I tried to upgrade my Device but When i install new update after two next Give me Error message said " Error 120:country id error" 5-5-N-8-N
and turn off my device and show only on to screen serial and on bottom Ver 1.06
PLS Help me
Country code errors =>
http://forum.xda-developers.com/viewtopic.php?t=12101&start=0
unfortenately you are now in a position that you can't see what your device was.
Do you remember what OS was on your device? Which update did you try?
Please read this post first http://forum.xda-developers.com/showthread.php?t=339961 I`m hoping someone can give me instructions in how i can do this so I can change or upgrade my rom.
Thanks in advanced
http://forum.xda-developers.com/showthread.php?t=322225
Download the herm1.nb file in that thread and flash it to your device using the instructrutions on page one.
http://forum.xda-developers.com/attachment.php?attachmentid=46888&d=1186868649. It uses Hermes 200.
If you want to edit it to a different Device ID, use a HEX Editor and edit bytes 4008-400D.
Hi Drummer 10630,
I have red the thread and I have to start by downgrading my spl and that’s just the problem I cannot downgrade or upgrade to anything because I keep on getting the error message Invalid model Id.
Now I’m trying my best to understand what it all says in the thread but what’s easy for you guys is Chinese to me and I’m from Holland.
So could you explain to me in lames terms which action I should take first to get my model id name changed back into HERM200 in nand.
I’m sorry if I’m a pain in the ash………e but I can’t do this without your help.
It's all in the thread. Read Mr Vanx's downgrading SPL pages...then flash the nand.
Hey Drummer10630,
Like I said I cannot downgrade I have red the thread several times and the Mr Vanx's downgrading SPL pages, tried the hard spl v7 but still get the error message invalid model id.
As you can read in this thread http://forum.xda-developers.com/showthread.php?t=339961 if I go to boot loader using the OK and Power button I get
H
IPL-1.01
H
SPL-1.40.Olipro
But if I use the spl wrapper I get
H
IPL-SSPL by des
H
SPL-1.09.ds
Does this make any difference?
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeGuide
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
ERROR ?242 : INVALID LANGUAGE ERROR ?244 : INVALID MODEL ID ERROR ?294 : INVALID VENDER ID ERROR ?296 : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
Hey Drummer10630,
I followed the instructions but it starts with installing HARD SPL which wont work because of the MODEL ID error so I skipped that and tried the rest and everything went fine I change the MODEL ID to H which is what it says on my device put the RUU_SIGNED.NBH file in the HTC rom folder and fired it up and guess what MODEL ID error.
I think what I need to do is to change my MODEL ID in nand like Olipro says.
Olipro said:
Your ModelID is stored on NAND and can be edited quite trivially (mostly).
how it got corrupted I don't know, however, the important question is; can you get into the OS?
Click to expand...
Click to collapse
device id
Hove the imei is related to the device id ?
There is relations ?
I mind part of the imei is the device id ?
Regards
Hello.
I want to change another version rom on HTC Hermes but when start loading new rom the "ERROR [262]: UPDATE ERROR
The rom update utility has encountered communication errors during the update process ... RECOVERY ...."
Phone is correctly connected to USB and entered on bootloader.
ex. Old rom is Schap's and i want to change to RDZ-ROM-STORM (for example) but not works!
When load similar version (Schap's) works!
What could be the problem?
Sorry 4 my eng.
Hi,
I have a big problem.
Sorry, but i already search in this forum but no success.
I upgraded a ATH100 with a SPL 3.65 ATH400 Rom
Now, i try to back to ATH100 but i cant. With PC and RomUtility, i get MODEL ID 244 error.
With SDCard i get 00058002 error while Loading...
Anybody can help me.?
Thanks
athena400back to 100
i was in too, now if you cant downgrade yet,sent me an Email ,to [email protected] and sending to me alot of pic from thet and information about your rom.
hi guys,
I had the same issue too....can not flash from SD card with 00058002 loading ...
any solution yet ??
hi guys,
I had the same issue too....can not flash from SD card with 00058002 loading ...
any solution yet ??
I have same problem. Please anybody can help me?
Try out This>>>>>
ERROR [244] : INVALID MODEL ID
from cmonex @xda-dev
This is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
NOTE, the command starts with a lowercase "L", not "I"!
WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx
13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.
Download: Mac1.zip mtty_0513_Test.zip
But where atachment ?
For me....WORK...THANKS again CMONEX
but i not do to repair wifi i want to flash my wm........
help me please ,,,
i make hard spl for athe400 in athe100
"ERROR [244] : INVALID MODEL ID
from cmonex @xda-dev
This is good for both corrupt modelid and corrupt wifi, and fixes both at the same time"
as it says it fixes corrupt modelid
It is worth a try
ERROR[244] :Invalid model ID ATHE100
Hi,where do i find the MAC adress for my ATHE100 as i cannot get forward from the bootloader?I am using SPL-v1.20.Olipro.Thanks to any1.
Yes, where is the MAC ADDR
As above, would be grateful if anyone would help us find where the MAC address and thanks for this thread this is the bane of most new owners and newbies. Cheers!!
Mac addr found, but......
Yes found the MAC address - it's under the battery cover, but having gone thru the whole process I got the following 3 errors at the end-
ERROR: no header matched
Transfer CERT error
Flash Programming Error
Thanx buddies!
3 ERROR Messages!!!
Hi Lakeman, could you help decipher these mysterious errors which I had after I have gone through the process twice
ERROR: no header matched
Transfer CERT error
Flash Programming Error
Thank you!
invalid Command
command error
whats wrong???
Cmd>lnb ameo.bin 76508000
lnb ameo.bin 76508000
Command error !!!
here you go >> http://xacsx.de
german ameo-site, roms, repair, and other helpful things
command error
whats wrong???
Cmd>lnb ameo.bin 76508000
lnb ameo.bin 76508000
Command error !!!
if you get notice
-> ERROR [242] : INVALID LANGUAGE
-> ERROR [244] : INVALID MODEL ID
-> ERROR [294] : INVALID VENDER ID
-> ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
stuck in bootloader. Help needed.
I have a HTC Athena x7500.
accidentally upgraded my htc x7500 WITH SSPL-Manual-x7510.zip of HTC X7510
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl is 1.10.0000
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed!
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
I have explored ruu_signeg.nbh in spanish rom with notepad jai entered the signer spl 1.10 I know if is sure or not
I believe there is a problem in the image rom saved in my athena rom
what I see on the screen of my athena is the spl 3.05.0000
The real spl is 1.10.0000 there is confusion in my spl
with mtty : task 32 level=ff
is what I can fix this problem with mtty
so if possible please guide me
I board on my pda (cid locked)on the Spanish language HTC_304
sorry for my bad Englis
thank you in advance
My email: [email protected]
http://forum.xda-developers.com/showpost.php?p=5205291&postcount=8
I think there is another thread somewhere about this but you could try the incorrect ID fix in the post above
and try to do the lower SPL
Hi all,
Here's my big problem I have right now
not return to stock HTC Rom for a return SAV is my topic in the section problem is transformed into ROM installation problem
http://www.forum-htc-dev.net/t53344-aide-retour-sav-jack-audio-hs
Can you help me when I run the RUU after it said 10% AC: ERROR [131]: ERROR ID CLIENT
I can watch one on the net and it looks like it come from:
ERROR [131]: ERROR ID CLIENT
One of these error messages displayed when you use the wrong RUU
to do the update. RUU will check if the Model ID and Language ID are
compatible with the Android phone. Make sure to use the correct RUU
to update.
Help me please guys!
This is my S-OFF with Revolutionary
try and flash from RUU. Not a rom, should get you back on stock.
http://forum.xda-developers.com/showthread.php?t=1208485
this error is with the RUU
Did you try S-On afterwards?
Connect phone to computer, open terminal, 'fastboot oem lock'