anyone have this problem? i leaded dcd new rom and it worked but i had to downsgrade and lock the phone back, i load the factory rom from htc website and now i cannot make calls. even with dcd rom i couldnt make any calls. anyone have any idea. i keep getting a recording that say i cannot make calls to that number i need to cal sprint for assistance
The new radio seems to erase your programing info on most peoples phones. Go to ##778# or just ##778 send and fill in the information that you know is wrong. Sprint i think you have to get an unlock code to edit this info which is based off your hes ESN #.
Lucky for me alltel is quite simple with their programing info with no unlock code and the only thing i needed to change was my phone number.
Thank you, this information was very helpful
Related
Sorry for the noob question, but i have looked everywhere and could not find an answer.
So yesterday I install nueSPL 2.47, on my Verizon XV6800 and then flashed to Radio 3.42.50 and then flashed to DCD Rom 3.2.6. I had some problems with authentication, so I called Verizon and they couldn't fix the problem at night because the system was down but they were able to fix things the next morning. Not sure what they did because they didn't give me a new A-Key over the phone.
So after that I was able to place calls out. I then downloaded the Verizon cab and was able to connect to the internet. I am also able to send and receive txt messages, but I can not receive phone calls. Now strangely after ending a call, I did receive one phone call but that was it. The rest of the time anyone calls it only rings on their end and then goes to voice mail. Then a few seconds later I will get a notification that I have a voicemail.
So since all this happened I have reflashed the dcd rom and reloaded the carrier cab. and called both *228 -1 and *228 -2. I still can call out, use gps, internet, and txt, but not get any calls. Any one have any ideas? Any help is greatly appreciated.
Thanks in advance.
that very interesting... I recently upgraded my father in law's phone and also experianed the same thing.
Also interesting, when I did the upgrade to my phone a few months ago I had to get an a key.. I also had to get one once after a hard reset. Perhaps they fixed something for this.
Keep calling VZW not all techs know what there talking about, eventuality you will run into one that know exactly how to fix your problem.
Quite a while ago, I flashed to DCD 3.2.6. After that, I noticed that I couldn't dial phone numbers from my contacts, but I could dial them directly. When I would dial using the contact, it would look like the call was going through, then I would get three error chimes and a message saying the call was disconnected.
Finally, I figured out that the difference is that in my contacts, the phone numbers all have "+1" before the number, i.e. "+1(206) 555-1212". This is the international prefix (http://en.wikipedia.org/wiki/List_of_international_call_prefixes#Syntax).
I assumed that this was a problem with DCD 3.2.6. However, I just flashed DCD 4.1.2, and the same issue is there. I suppose I could go through all 223 of my contacts and edit the phone numbers to get rid of the plus sign. However, this is the correct format for a number, and non-custom ROMs have worked fine with it.
Anyone got an idea of how to get the dialer with DCD 4.1.2 to work with these phone numbers? I'm guessing I just need to change some configuration relating to my International Prefix (U.S.) Alternatively, does anyone know of a ROM that does work with these phone numbers and also keeps the GPS and tethering (via Internet Sharing) working on my Verizon XV6800?
Thanks,
Jamie
Got it
Okay, I found it.
In the dialer application, go to "Menu", "Options...", "Services" tab, scroll down to "Plus Code Dialing". The rest is self-explanatory.
Hopefully, this will save someone else some time.
Jamie
Okay, I'm on Sprint. When I install an AOSP rom, it says that I need to activate my device.
Using the activation call built into the rom says:
"The number or code you dialed is incorrect."
Dialing *228 says the same thing.
From what I've seen in Settings About I can speculate what is wrong, but I'm not really sure. Could someone elaborate on what I need to do if I'd rather not flash back to another sense rom.
And why do I still have 3g if my phone isn't activated?
Thank you.
try dialing *2
or just call sprint and tell them to re-provision you sprint account
I have a VZW i605 Note 2.
I am using AT&T service.
I have JellyBeans 21 ROM installed.
OK, on to the question...
When I receive a phone call the call back number is wrong. From what I have read it is an issue with non Verizon service or something.
If I were to get a call from 18147259951 it would show up as +8147259951 in my recent calls list, making it impossible for me to easily call them back from that screen.
Does anyone have any idea of how this could be fixed?
I know I can just install an international ROM and it will work, however then my GPS will not work. (I also really like JellyBeans)
This has been bugging me for some time now and I would greatly appriciate any assistance I can get.
Deleted
After finally updating PRL, adding phone number and getting the phone recognize it. I found out that I can't make calls neither receive them.
I see everything normal but when I dial, nothing happens, it stays there, no sound at all.
Also when I call to this phone, I get the voice mail messages.
So obviously, I'm missing something.
I got CDMA Workshop, DFS AND QPST, I followed a guide that I found here and chaging a few things here and there since I live in Dominican Republic.
Anybody here knows something about this? Im struggling and desperate to make this phone works
Do you still have the phone? I posted a guide that may help you discover what's missing with your phone configuration: http://forum.xda-developers.com/showthread.php?t=2720046