Helllo Guys,
Has anyone successfully Jtaged a RW6828 i have built a jtag interface and using the JFLASHMM utility i have used an eboot.nbo ( the latest bootloader for the HP rw6828) file.. and got the unit to flash which programs the device, once i put it together i still dont get it to boot up to the bootloader
i used the following commands which have been stated in the start.bat file
jflashmm pxa27x32 ebo_a.nb0 N 0 PAR
jflashmm pxa27x32 ebo_a.nb0 N 3F40000 PAR
any thoughts i really want to get my PDA going again
once again thank you
ABS
bump bump...
i have followed the wiki link also on how ot repair a dead boot loader..
if this info helps.. the unit again as explain did flash in both memory blocks successfully..
i also verified the data and it was all successful using the v command..
i also plugged the unit into the usb port of the p.c. and the led lights reddy orange and also after a while it flicks between red and green?
any thoughts guys hopefully i can revive this PDA..
ABS
bump bump bump bump it up
its working thanx
Related
Hope anyone can help me - i' am still stuck - after trying and reading posts for 6 hours. i tried to flash the touch flo w6 rom on my charmer. activesync disconected during the flash proces. charmer does not start anymore - but i can get to bootloader screen.
But all roms i found and tried to flash need an activesync connection. could someone pls let me know how to flash from bootloader without active sync and where to find such a rom - if possible a w6 - if not w5 is also very very welcome!
Thanks a lot in adv!
are you using Vista ?
Good morning Urkraft!
Actually I do - but if nessecary I have ease access to a Computer running XP.
you need to use a PC running XP, then please try to flash the base ROM as Vdlock mention in his thread : http://www.tm-phonedownloads.com/fil...ileUK_Ship.exe
Reset to bootloader then connect teh USB cable to an XP machine and run teh above shipped ROM installer
Please make sure you do this before your goes flat, if you notice now it might not be even charging ...
Charmer is running again! Tks a lot Urkraft
And yes - I tried again - WM6 is running fine!
the link doesnt work is there a new one?
The link is dead... Please.... somebody help
Please update the link, it's dead and i'm in really need. Thanks in advance!
Hi All,
Yes I searched, could not find a helpful post that I could understand (unfortunately a lot of not-so-good english on these forums!).
I used the file 'windowsmobile2003se.exe' here;
http://forum.xda-developers.com/showthread.php?t=230279
It started loading fine, then when it came up with the progress bar to start updating, my device rebooted and is now stuck in bootloader.
When I try himaupgradeut.exe, it gives me a ERROR 101: Connection Error. USB is disabled in ActiveSync and I can see the device as "Microsoft USB Sync".
The USB still works (I can use mtty and xda2unlock in Windows XP and they both work fine). Is the device still recoverable?
I have hard reset (Power + Reset), removed and re-inserted battery and tried a normal reset, none of these work.
Can I please have some step-by-step instructions on how to recover the phone? The bootloader version is 1.06
Thanks.
can you get some pics?
Have you tryed leaving the battery out for 1 day or over night. Because that fixed some problems for me.
try it
flyboy
Yeah I've left the battery out overnight (about 12 hours to make sure the backup battery ran flat). It's still stuck on the boatloader.
It's just got the normal bootloader screen (Serial up top and 1.06 down the bottom) and this changes to USB when in the cradle, so the device seems to be fine.
Any ideas?
Solution found!
I HAVE FOUND A SOLUTION FOR RECOVERING FROM BOOTLOADER!
Full props and thanks go to utak3r of buzzdev.net
Please go to this thread.
http://buzzdev.net/viewtopic.php?f=8&t=36437&start=0
MODS: Please sticky this. Please.
Hi All,
I have made a script that people can use to easily flash their Himalaya without performing all the above steps manually.
My extreme and eternal thanks go to utak3r (from BuzzDev), xda-developers.com and buzzdev.net for building such great communities and for providing so much help and information (even if it is a little hard to follow sometimes!).
You can download it from;
http://members.iinet.net.au/~nomicakes/MakeSDBoot.zip
http://www.clonnyserver.com/uploads/tools/himalaya/MakeSDBoot.zip
The zip file contains the script and the tools neccesary to do this.
As above, if you aren't familar with flashing devices and the possible outcomes, DO NOT USE THIS TOOL.
Hi there,
Yesterday I tried to upgrade my Qtek 2020 to the last rom available but something went wrong and now my PPC only shows the bootloader screen.
After hours of researching on Google I found this forum and this topic. I tried to do what is in utak3r tutorial but I can't connect to my PPC using mtty (usb port can't open) and I don't know why. :\
When I try himaupgradeut.exe, it gives me a ERROR 101: Connection Error too...
And finally when I run this script made by Clontarf it fails on the last step on writing to the SD card. It gives me a Error - Access Denied.
I don't know how to solve this. Would you please help me?
Problem solved!
Hello,
I've got a bricked Leo. I've bought it with the description that has fallen down, and doesn't work any more.
Actually the display and the digitizer is fine, but the flex board is cut and it doesn't boot any more. Via USB it is recognized as "Qualcomm CDMA...". I guess it's flashed with a wrong radio as it is the US version.
Can someone tell me what I've to do via JTAG to restore it? Just delete an part of the ROM? Or load the bootloader to a specific address in RAM and start it from there to flash a valid ROM?
I've got the knowledge to solder such fine pitch parts and also have a JTAG adapter that works with open OCD, but don't know what to do in that case.
Maybe someone from Germany is reading this, who has the knowledge and the technique, who I can send the mainboard to flash it.
I would be very glad if someone could help me with this!
It seems to be possible to access the device with QPST. QPST finds a Phone in download mode and it might be possible to download a boot image, OS image and so on.
But it doesn't accept .nbh files. Boot image must be a .hex file. So I tried to extract the spl from a stock rom and build an intel hex file, but the QPST downloader doesn't accept this format: "could not open flash programming file".
Any idea how this hex file has to look?
Have you made any progress?
same thang just happend to me!
i flashed
RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50.07U_2.08.50.08_2_Ship.exe
and all was well but i realy didnt like tmoble logos so i tryed
RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship.exe
and aperently it bricked my phone because it wont turn on now!
i hit the yellow button next to teh battery with no luck the phone is now dead!
it was instantly recognised buy my pc as a cdma phone when it was bricked!
now what?
please someone help us!
You did indeed brick your precious HD2 by not reading this forum. It was stated over and over again that flashing a TMOUS HD2 with a .51 ROM will brick your phone. Flashing is not for the faint of heart. You thought you were in the right league, but alas. Back to the minors with a nice Nokia. Good luck!
Hi all, i'm searching for some info since yesterday. I have read (hoping) everything about how to unbrick this tablet (folio 100). A friend of mine tried to install cwm on his Toshiba F100 and got stuck with:
"magic value mismatch.
critical failure. unable to start kernel.
unrecoverable bootloader error (0x00000002)".
So, i was trying to repair it with nvflash. but, when i put it on APX mode, my pc won't see it. If i turn it on fastboot, my pc installs the driver for fastboot (so it can be seen on fastboot).
What to do if my pc don't want to see it on APX mode?? (using Windows 7 / 32 bit)
Thank you for your support
Reflash from fastboot?
Sent from my IDEOS S7 Slim using XDA App
Thank you for your reply. ok. i will try with fastboot. but where to look for info and what to install? i'm all kinda dizzie. i've read a lot on the forum, but i don't see exactly what to do (maybe i'm too stupid). it's much easier with my phone than with this tablet. thanks
PS: Do i need any external memory card?
http://forum.xda-developers.com/showthread.php?t=1119507
Fastboot set up guide
Sent from my IDEOS S7 Slim using XDA App
Thanks. Problem solved. It was easier than I expected . Topic can be closed/deleted
Hi ghuyz.. newbie hir, trying to find all ways to revive by Smartphone... here's what happened:
first, i accidentaly formatted the sys boot of my device, resulting to a "reset for entry qpst" error because according to some geeks out there, formatting sysboot actually formats the partition 3 instead of partition 8.. as a resolve for this, i followed certain instructions on how to fix this kind of problem.. unfortunately, i cant find any complete procedures for karbonn s1, so i gambled to follow instructions for karbonn a9+ .. Now my phone is totally dead! It won't power on anymore. It wont even show "charging" when pluged in. I'm just a poor little guy who can't afford buying a new one anymore. For those geeks who have a benevolent heart out there, Please Help! I hate goint to service centers promising me to wait 4 at least 3 months before they can repair it.
Thanks and Godbless..
android4279 said:
Hi ghuyz.. newbie hir, trying to find all ways to revive by Smartphone... here's what happened:
first, i accidentaly formatted the sys boot of my device, resulting to a "reset for entry qpst" error because according to some geeks out there, formatting sysboot actually formats the partition 3 instead of partition 8.. as a resolve for this, i followed certain instructions on how to fix this kind of problem.. unfortunately, i cant find any complete procedures for karbonn s1, so i gambled to follow instructions for karbonn a9+ .. Now my phone is totally dead! It won't power on anymore. It wont even show "charging" when pluged in. I'm just a poor little guy who can't afford buying a new one anymore. For those geeks who have a benevolent heart out there, Please Help! I hate goint to service centers promising me to wait 4 at least 3 months before they can repair it.
Thanks and Godbless..
Click to expand...
Click to collapse
I have the same issue I was trying to install new rom and unfortunately reformat the system drive...if you unroot your phone and ask your manufacturer to repair it or replace it you should have a good acting skills, don't tell them that you were trying to install new ROM because the warranty doesn't include system issues...
GL...
BTW: I wasn't able to find any fix for this issue...I just use my acting skills...LOL
Bricked S5
That happened to my Karbonn TitanS5 or cherry mobile Skyfire 2.0 aswell .. anyone have a walkaround for this?
christopher.silan said:
That happened to my Karbonn TitanS5 or cherry mobile Skyfire 2.0 aswell .. anyone have a walkaround for this?
Click to expand...
Click to collapse
yes there is always a solution, download stock ROM n flash it find the stock ROM in my signature
An image for flame 2
Hmm maybe if somebody can get us a flame2 image
IM Not sure but by going to QPST Download mode nd connecting it to windows and making a backup image through acronis somebody can help us
And we restore the image using the same method.
Request people to connect qpst mode to linux and give us the boot files as windows cant recognize the partitions.
Im also stuck in a similar problem
hope someone can help
You find solution..???
YOU Found SOLUTION..???
YOU Found SOLUTION..???
YOU Found SOLUTION..???
Sort of
kaushal9128 said:
YOU Found SOLUTION..???
YOU Found SOLUTION..???
YOU Found SOLUTION..???
Click to expand...
Click to collapse
Sort of
We Actually need someone who does have a working Titanium S1 or Cherry Flame2.
If you find someone who does have it Please ask them to do the following
1) Switch off the Working Mobile
2) Switch it on by pressing the vol+ Key and wait untill it shows the "Entry QPST Download" Screen
3) Connect your mobile to Windows
4) Start Acronis and make a Sector by sector backup
5) Now Switch on your bricked mobile and connect it to windows
6) Start Acronis and do a restore that you made from the working Titanium S1 or Flame2
7) Reboot
This should do the job.However i was unable to find someone with the same mobile.Hope Somebody can help.
If anybody has the Backup.Please post it so that others can also Restore their mobile if bricked.
Thank you
I will!!
I will make one soon As I get the Phone in hands.. I sure will... Just have patients !!
Please Do!
Please Do!!
I Have sent my mobile to the service center and it has been over three weeks and still no result.
I'll take it back and do it myself as soon as an image surfaces out.
And Thanks!!
That'll be of great Help
Karbonn s1 Titanium/Cherry Flame 2.0 Partition 3 Backup
Did anybody got the solution for fixing a hard brick Karbonn S1 titanium???? By mistake i formatted my boot from clockworkmod... n from that tym its showing Reset for entry qpst download... idk how to fix it... Please sum1 help me out... now its completely dead... so charging... nothing.... Please help me..
Thanks In Advance
Rohan
warmachine68 said:
Did anybody got the solution for fixing a hard brick Karbonn S1 titanium???? By mistake i formatted my boot from clockworkmod... n from that tym its showing Reset for entry qpst download... idk how to fix it... Please sum1 help me out... now its completely dead... so charging... nothing.... Please help me..
Thanks In Advance
Rohan
Click to expand...
Click to collapse
:crying::crying::crying:
Yeah Same Happened With Me No Flashing Lights While Trying To Charge..
0k gonna go round..
OK ok I saw this.I know how you feel.Once I soft bricked my Samsung Galaxy S2..That's so bad.Here's possible solution.Download original ROM from somewhere idk you find it.Download Odin.Try to insert new software with it.If it doesn't works I am so so sorry.
As I heard before the only solution for hard bricked devices is.
Go to very tall building,go to top and throw your phone from there and cry..
For Soft Bricked you can fix it easy.You need to install new ROM.
Soft Bricked or Bootlooped is when you hear only sounds.Your phone reacts on charging but you don't see anything and you can boot into recovery and turn on and off your device.
Hard Bricked Device- Well nothing works.Solution is to throw it into junk..
I'll look out somewhere if I can find any solution.
Solution
android4279 said:
Hi ghuyz.. newbie hir, trying to find all ways to revive by Smartphone... here's what happened:
first, i accidentaly formatted the sys boot of my device, resulting to a "reset for entry qpst" error because according to some geeks out there, formatting sysboot actually formats the partition 3 instead of partition 8.. as a resolve for this, i followed certain instructions on how to fix this kind of problem.. unfortunately, i cant find any complete procedures for karbonn s1, so i gambled to follow instructions for karbonn a9+ .. Now my phone is totally dead! It won't power on anymore. It wont even show "charging" when pluged in. I'm just a poor little guy who can't afford buying a new one anymore. For those geeks who have a benevolent heart out there, Please Help! I hate goint to service centers promising me to wait 4 at least 3 months before they can repair it.
Thanks and Godbless..
Click to expand...
Click to collapse
Hey i think i found solution for this but i haven't tried it yet coz i don't have linux http://forum.xda-developers.com/showthread.php?t=2573743 if u find it useful or have any other solution please let me know. I am so upset since when my S1 is hard brickes that i am using nokia 1208 . please msg me if u find the solution
idragon81 said:
Sort of
We Actually need someone who does have a working Titanium S1 or Cherry Flame2.
If you find someone who does have it Please ask them to do the following
1) Switch off the Working Mobile
2) Switch it on by pressing the vol+ Key and wait untill it shows the "Entry QPST Download" Screen
3) Connect your mobile to Windows
4) Start Acronis and make a Sector by sector backup
5) Now Switch on your bricked mobile and connect it to windows
6) Start Acronis and do a restore that you made from the working Titanium S1 or Flame2
7) Reboot
This should do the job.However i was unable to find someone with the same mobile.Hope Somebody can help.
If anybody has the Backup.Please post it so that others can also Restore their mobile if bricked.
Thank you
Click to expand...
Click to collapse
I was going to post a same request. But i thought i will find it myself. Then i found instructions using acronis with an img file of Archos Platinum 50. Then i flashed that file on S1. Now my phone won't even show RESET FOR ENTRY QPST DOWNLOAD. However it can enter ENTRY QPST DOWNLOAD.
kalmukale said:
I was going to post a same request. But i thought i will find it myself. Then i found instructions using acronis with an img file of Archos Platinum 50. Then i flashed that file on S1. Now my phone won't even show RESET FOR ENTRY QPST DOWNLOAD. However it can enter ENTRY QPST DOWNLOAD.
Click to expand...
Click to collapse
Made a backup of the partitions following you method......but came up with lots of them and dont know which partition is the right one
here is the screenshot
Help!
adubu said:
Made a backup of the partitions following you method......but came up with lots of them and dont know which partition is the right one
here is the screenshot
Click to expand...
Click to collapse
Can anyone please help us.. on how to build the correct image back up for Cherry mobile flame 2.0, we need a complete package that can be flashed thru EMMC Download... or better yet sir can you make a back up using the emmc Download tool? thanks a bunch!
looking forward to resolve this issue.
Can anyone please... Post a Acronis backup file of Partition3sector for Karbonn titanium S1 please.......