Sorry, newbie question, but before I have to use my MDA Vario 2 as a door stop, does anyone know if it is possible to get out of the Multi Coloured Screen ? our office had a power cut while I was updating from WM5 to WM6 and now it is stuck on the following screen:
HERM300
IPL-1.01
HERM300
SPL-1.40.Olipro
USB or Serial (Depending if I have the usb cable connected)
Obviously I cant connect to the phone as it is not booting and Active Sync is not connecting so I can upgrade.
Am I buggered like a cat in battersea dogs home ?
OK, false Alarm, was able to recover using a hard re-set + power on button and then load the original SPL loader ! phew ! RTFM me thinks !
U lucky bastard
Ha wow best case scenario from a worst case scenario.
That would piss me off if a brick wasn't my fault haha.
Tell me about it I was, how can you say "*hitting bricks", but it's all working now. I feel so like a virgin, I firstly purchased a ROM off Ebay and then when that didn't work I had a search on the web and found this great site Now to find out more about custom apps !
marcoryn said:
U lucky bastard
Click to expand...
Click to collapse
<laughs> Agreed.
Glad everything worked out. Good luck!
I spoke way too soon, Everything was perfect and then half a hour ago I changed a setting in the advance configuration section about ext ROM, took a telephone call and then re-started the phone..................now it just hangs at the WM6 splash screen !
Hi, I'm new here. Since I've read a lot of posts and guides I've learned alot. Sorry if my english isn't very good, spanish is my first language
I bought a Qtek s200 that couldn't boot, and thanks to the great members of this forum, now it is alive.
I flashed it first with the official qtek file.. nothing, then I used the PVtemp (that was the name i think).
The problem I have is that the device works SO SO SLOW !
with WM5 it was slow. I flashed to the WM 6.1 shadow 2.0 using dioxda2 's guide, and everything is fine, except that my device takes 15 minutes to start windows, and for example I point start and it appears almost inmediatly, but if i open something it takes between 30 seconds - 1 minute... to open for example the comm manager.
I will try to flash now to Korand's flash that the users say that it's very fast.
I don't know what to do.. Any suggestions?
I am almost sure that my Radio Rom is the 2.47
Thanks in advance !
update: I changed the PP to 6 mb and it works a LITTLE BIT faster, let's say that it took him 8 minutes instead of ten :S what can i do :S
update 2: can the SD slower it down so much? I took it out and it works faster.. let's say that now it's a little bit slow, so it's almost like it is normal... is the card the problem?
Well... know that Audiomanager sucks for boot time, as it puts all it's files in /windows. Try one of the "clean" roms, and don't install much. Also, use quickmenu or x-button to kill programs, freeing up ram. Occational hibernates also work. Other than that, I don't know.
i shutted down some tasks and it works perfect now.. WITHOUT the SD.
now i'm trying with a 16 mb SD card from a cannon camera, the original cannon card, but it seems to be slow again :S
EDIT: it boots up slow but it works fine. The 1 gb card is a kingston...
do I have to format the SD cards in some special way? do I need some special SD card ( I mean because of the read write timings)
haveing same phone but no problem...!
try to use this one it should work like charm.
WM6.1 Korand WWE 3.1 (based on official rom)
http://forum.xda-developers.com/showthread.php?t=366313
hope this might help u out.
it should actually.
Hello and welcome to the forum.
You can also try to use a softweare called Batery Status, it can overclock your prophet so it can be faster.
I use it in mine and really speeds up a bit.You can find it here
http://forum.xda-developers.com/showthread.php?t=270751
I tried the Korand flash With Out the SD card and it runs SO GOOD but if I put that 1 Gb SD card the system is slow (not so slow as before, but slow), I will buy a new card today.
The problem that I've with Korand's flash is that when ]I try to see the battery status, it says unknown... and the icon is like it's always charging.. so any idea on how can I solve that?
thanks !
Since both memory cards you have tried slow it down, it might be a problem with your device, although given how tough they are, I doubt that. Try a new memory card and see if that helps, and maybe try a WM5 ROM with a different memory card to see if it still happens.
Ok, I tried with another card and it works VERY NICE so I will buy some faster card.
Now I am having a BIGGER PROBLEM.
As I couldn't saw the battery status, the battery is dead now, the phone turned itself off suddenly and I tried to turn it on, the screen went on and then it was off again so I supose that the problem is the battery. The problem is that it is not charging the battery, or I think so. Is there any way to see if the battery is being charged?
If i plug it to the USB while it's off, the battery is being charged?
Thanks !
Does the LED show anything when you plug it in?
no, there is no led on.
I took out the battery upper case, so I have the lithium pack and everything in it's place, and in the phone, with the carger, and the lithium pack is getting a little bit hot. I measured the voltage of the battery, and while it's charging it's like 3.65, so I am letting it charge to see, but there is NO LED on :S
any ideas?
Umm... I think you may need to "reset" the battery. I found a discussion on doing that sometime ago, but don't have the link to hand. Try a search for battery reset or something like that, and I'll see if I can find a link for you.
Hey there
First of all, thanks for your help, I know that in the forums we try to help each other, but really, thank u for all.
Now my device is alive again after half an hour charging, it's on.
What's the problem then? There is not any led ON while the charger is in there, and also, I still can't see the battery status on the windows mobile. Now i'll try to install the battery status cab that you told me (I thought that i needed to justo run it to install, but it seems to be in a different way. I'll search now).
I searched for battery reset, I found it for another model, they were talking about some button, like the soft reset one, but i can't fin anything similar in my device.
I've installed the Battery Status package, and it shows now like it's plugged an it says -1 %
the rest of the phone is working VERY GOOD
welcome gdline,
your device, it's a new or a second hand prophet?
perhaps your problems are related about this issue, it's unusual no led when you're charging your s200, where did you buy it?
PD spanish is my first language too, and your english is so good to understand you very well
actually I bought it second hand, I couldn't afford a new one.
gdlin said:
actually I bought it second hand, I couldn't afford a new one.
Click to expand...
Click to collapse
I think that's the reason of your problem but, if the device is working right about wifi, bluetooth and all of things you would want, it's a good choice
saludos
It works great.
How much days can the phone survive without charging?
Depends on the ROM, and on the usage. Light usage with a clean ROM can get 2/3 days usage. Heavy use with a ROM packed with programs and you'll be lucky to get one days usage.
so it seems that the solution is to charge it every day or one day charge it and the next day don't :S
I still don't understand why couldn't I change the radio rom :S
thanks
I charge mine almost every day because I don't like the risk that I might run out of battery! I also use it quite a lot for music...
I just flashed a new radio and it completed it but now my phone will not reboot at all , ive took the battery out and put it back in and still nothing can someone please help me
1- this is in the wrong forum...
2- you need to give a lot more info. like what phone you have, what rom/radio you are running and what radio you flashed. and what steps exactly you did. exact steps.
have a htc hd2 and i the radio is 2.095103 and i went to 7 zip and extracrted it their after the download went to a 100 percent and then the phone cut off and now nothing , no power
and i have diniks rom
and when i plug it into the computer it makes that noise like its connected but still a black screen
is it a tmobile us hd2??
green and red hard keys??
t mobile UNITED STATES AND YES GREEN AND RED
Ok I hate to be the bearer of bad news but......
if the radio you flashed has .51. in it then your phone is dead.
You may be able to claim it on warranty........ just dont mention flashing anything.....
Really , dang so theirs nothing i can do at all, no tricks . And thank u for trying to help out
Sorry man its gone........ those radios are for the EU Hd2's and will completely screw a US model.....
People have said that they managed to get a warranty replacement........ after all, you woke up in the morning and the phone was dead not your fault right??
if you see what I mean......
your exactly right , i get what your saying..... see the phone was a replacement phone anyways cause the original got stolen and i have 180 days if someting goes wrong
You should be fine then..........
next time just remember....
NO 51 RADIOS!!!!!
Hope it all works out for you.........
i got it taken care of , so even when they get it they wont b able to fix or figure out what is wrong with it right
Hello all.
Got an Neo V today and updated to last version firmware SE.
Everything ok if working with it, if i let it in idle when i try to wake it up he don't show a thing but restart it self.
I tryed to read on forum for an answer and coudnt find one.
If u know anything about it plz let me know. This is annoying...
Thanks in advance
If it's connected to energy PC or 220v it wount restart...
maybe your battery is malfunction.
Try to bring it to service center.
Hello.
to start, sorry my bad english.
"used phone, seller didnt know why phone didnt start."
so here is the proplem, just got HTC Titan(used phone) and it wont start, so i opened it the wet stamps or something was red.
and so it wont star, is there anyting i can do?
or do i have to go shop to give it them to fix it?
ask if you didnt understood so i'll try to tell something !
So i sended it to ultrasound wash, they sayed that maindoard etc. looks fine now, but it wont still wake.
is there anyting to do ?
weird thing is that it won't discharge battery.