please need help for dead ipaq rw6815 no boot up after wrong rom upgrade -
jtag operation terminate but no boot . thanks fo all
Related
hi everyone,
i have a huge problem. my rom flash for my i-mate (qtek 2020, mdaII, XDAII) hung during flashing (from 1.66 to 1.72 official i-mate rom) during the ce upgrade step 2. now my i-mate just hangs at the blue i-mate screen and i cant connect to it through pc anymore, get error 101. is there any way to get a good rom on it again (can i connect to the ppc by another way, other software or sd-card0 so it will work again, or does it have to be epaired at at a rapaircenter?
thnx, sorry for the bad english
See the pm i send you.
I have the same problem ...
plz tell me how u solve it
Best regards
plz help, i-mate dead after failed flash, error 101
Hi,
If all that happened was it hung during upgrade you can put the device into bootloader, power+d-pad+softreset button, and attempt upgrade again, but if OS you were upgrading to is corrupt causing the hang a new rom might be the way to go, www.buzzdev.net has everything i needed, or clubimate.com
I have same problem. My q-tec100 is reseting so I can' connect it to pc for flashing again. Please tel me what is bootloader and what is d-pad button so thad i can stop it from reset and connecting for flash
hi friends i have the same prob. somebody plz help me too
I have HT7 Phone it bricks during upgrading the SPL because it had WM5 and I went to install WM6
I can boot the Phone in Recovery Mode ( Holding the Camera Button and Boot ). Three Color Screen and I can communicate with the phone through the MTTY but during installing the Update it says ERROR 300
is there anyway to get the phone alive again ?
Thanks for your Help
** I have Kaiser and it's not mine , it was belong to my friend and I damaged his phone
PS : Phone is out of warranty and there is no service center here , also I can't use the JTAG Method
jafer mainly error 300 comes in when you are using wrong rom update utility... atleast in my case...after running spl pgm from phone and mtty program make sure you run the rom update utility inside the spl folder before running the rom update utility inside the rom folder... hope this helps.. and make sure that the rom is for old gene...
which spl its nowing at the tricolor screen now... oref or olipro?
which spl its showing at the tricolor screen now... oref or olipro?
ONBL 1.10.0000
SPL 1.07.oref
Thank you
Could you please explain more , where to get those files
I got Unbricker from here
http://forum.xda-developers.com/showpost.php?p=2784291&postcount=66
Thank you again
Question : when TriColor Launched can I re-flash the original firmware ? i don't know what to do now
Please look at the stickey, krazy has made quite a good tutorial about flashing etc and has all the tools hyperlinked. LoL
Hi Thanks but please don't refer me to reads topics , because i've already read all of them
The Phone is HT7 , during the upgrade it bricks , I used the " Orefkov " but it seems it only works for new Phones
Anyway by no I can Boot the Phone in Tri Color Mode but when i try to upgrade a rom it says ERORR 300
is there any way to BOOT the Phone through the SD Card ? I already had the same issue with another phone , I boot the phone with SDCard and it became alive again !!
But I don't know the Instructions for this GENO Crappy Phone
try removing the SD card and update the ROM. BTW as far as i know oref Is for new Gene. post a query on the right thread and ankit or krazy or any proficient member will definitely help you out. or you may pm basha for help.
HELLO
i am a new member and sorry for my bad english
my problem that i ve upgrade my hermes and unloked sid ,but i killed my Hermes by trying to fix a "NoGSM error"
now my hermes don t start i can 'thave the boot screen ,only if take the power botton +to access boot screen i traid all solutions but no success
i ve not access to ktl mode;for this resons i supluy your help,i have connet herms and launch device monitoring and officiel rom ,result is attached down,
herm200
IPL 1.04
SPL 2.03
THINKS
Hello STAMBITA, try with mtty for fix problem.
If your OS don't start you try JTAG mode because your Hermes is not super cid (SPL 2.03) for fix problem.
See the post http://forum.xda-developers.com/showthread.php?t=391047&page=17.
Regards
nico
STAMBITA do you have access to a rom provided by your telco? If so try to flash that rom while you're in the bootloader. Since your device isn't supercid it's either that, or JTAG or send it to a repair centre. I'm sorry.
I ve not access to room .with mtty nothing happen nothing .the last solution is to try jtag but is complicate to do.to send for repair centre it cost the price of new one?
Hello guys!
I have a big problem. I tried to flash HardSPL (via MemoryStick) on my raphael. After the flash process, raphael restart, but it starten with the tricolor screen and it shows me dthe massage "Upgrade ROM code error, please try again".
and a few seconds later raphael starts the proces again, after 3-4 tryouts the screen freez and now i can nothin do.
can someone help me?
sorry for my bad english.
best regards,
sasuke213
sasuke213 said:
Hello guys!
I have a big problem. I tried to flash HardSPL (via MemoryStick) on my raphael. After the flash process, raphael restart, but it starten with the tricolor screen and it shows me dthe massage "Upgrade ROM code error, please try again".
and a few seconds later raphael starts the proces again, after 3-4 tryouts the screen freez and now i can nothin do.
can someone help me?
sorry for my bad english.
best regards,
sasuke213
Click to expand...
Click to collapse
We need more info...
Is your phone CDMA or GSM?
Did you flash HardSPL from XDA?
Can you enter the boot screen and try to reflash the Hard SPL?
Problem #1 is that you need to flash hard spl off of a pc through a usb cable. Like it says in the thread (assuming you read it), you can't flash hard spl off of an sd card.
Try soft resetting, and see if the phone boots up normally. Did you flash the correct hard spl (incorrectly)? If you used a hard spl from the wrong device, the game may be over. My advice is to download the proper hard spl and to flash it according to the instructions in the thread.
hi all
i try to Upgrade my gene to official ROM but this installed to 2% and restart then
my gene showing
3 Color screen
and this msg
ONBL...............
SPL 1.28.0000
DONT POWER OFF!
PLS .UPADTE NEW IMAGE NOW!
And in the white band RE-FORMATTING OK!
pls help me to fix it
also i try to install other ROMs but they all not work .
up
light25360 said:
hi all
i try to Upgrade my gene to official ROM but this installed to 2% and restart then
my gene showing
3 Color screen
and this msg
ONBL...............
SPL 1.28.0000
DONT POWER OFF!
PLS .UPADTE NEW IMAGE NOW!
And in the white band RE-FORMATTING OK!
pls help me to fix it
also i try to install other ROMs but they all not work .
Click to expand...
Click to collapse
Any official ROM can not be flashed directly you must go through this process
http://forum.xda-developers.com/showthread.php?t=506467
You must remove spl.nb,gsm.nb and other .nb files but not os.nb because they will mess up with your device's spl and bricks it.
Since you have already flashed this ROM, unfortunately you've bricked your device.......
So, i would suggest you to patch your SPL via this guide http://forum.xda-developers.com/showthread.php?t=472169 and then try to flash custom made ROMs.
Other way is to remove that bad flashed spl.nb file but don't know the method to do it....
I have always used the Orefkov method for flash it but This time my downloaded ROM was a Installation file and i dont use orefkov method just Got connected to usb and run this file but after 2% my gene restarted and Revealed this msg :
ONBL
SPL 1.28.0000
DONT POWER OFF!
PLS .UPADTE NEW IMAGE NOW!
RE-FORMATTING OK!
I also downloaded this ROM from shiped ROm site
How can I repair this
pls help me bro
light25360 said:
I have always used the Orefkov method for flash it but This time my downloaded ROM was a Installation file and i dont use orefkov method just Got connected to usb and run this file but after 2% my gene restarted and Revealed this msg :
ONBL
SPL 1.28.0000
DONT POWER OFF!
PLS .UPADTE NEW IMAGE NOW!
RE-FORMATTING OK!
I also downloaded this ROM from shiped ROm site
How can I repair this
pls help me bro
Click to expand...
Click to collapse
I don't know what to do now.....
But what about this??
GENE J-TAG Restore
ok I did not try JTAG Method but tnx for your help dear mr.harsh .
I would try this method and I will say results in this thread
also sry for my bad eng