i've reflashed my rw6815 (original ipaq) with the latest rom (original hp rom), and now my gsm part is not detected anymore. with the selftest of gsm /imei i get the message that the gsm module is not detected? i am running bootloader 1.05. any suggestions how to get it to work again? i tried reflashing the same latest hp rom several times. is there a way to only upgrade / reinstall the radio=gsm rom?
any help is appreciated
Related
I have my xda fixed by O2 with a new bootloader 6.22. I tried to downgrade to 5.15 without any success. I did downgrade my 5.17 to 5.15 without any problem, but cant repeat it for the 6.22.
Can anyone please help?
are you using 'pnewbootloader' to do this?
it only works for a limited nr of rom versions.
what rom version do you have?
ROM version 3.20.06ENG dated 07/30/03
I used the bootloaderfix batch file withuot any success, then
I wrote the 5.17 patch to SD also did not work, then
I wrote the 5.15 ROM image to the SD using XDArit10 also no success
I put the xda on the cradle connected to the PC thru USB and tried to run the pnewbootloader, without any luck. Nothing happened
my objective is actually to upgrade the O2 ROM to ATT WM2003. But I dont want to upgrade the radio stack. Suppose it is impossible to trick the wallaby 6.22 to accept the SD. How about running the ATT WM2003 upgrade, but removing the RSU upgrade application program in order to 'stop' the rsu upgrade from running. Will this work?
THanks a lot for your help...
Does anyone have the Orange UK rom ?
Not the : HER_ORRO_123702_1060400_WWE_SHIP.exe
I have a UK preproduction unit and need the rom for this device.
Thanks,
P
What's the problem with your prepro version? older bootloader and not flashing from sd-card?
PrePro TyTn
I updated it with a Imat rom.. no problem (it's a unlocked PDA).
A couple of weeks later i was updating it with the HTC rom and my laptop went in standby mode during the update
Now my pda starts up in de bootloader screen (1.06).
No reset option will work, mtty1[1].42.exe (set 14 0) does not work eighter.
If it try to update it again it gives a "Vendor ID error".
It's a Orange UK device, and it think i need the Orange UK rom.
I tried HER_ORRO_123702_1060400_WWE_SHIP.exe...no succes.
It's the only Orange Rom i can find.
Need some help... can't use the PDA anymore
Thanks for your help..
Pim
If it's a preproduction device it should be SuperCID, but I guess your CID got corrupted during the bad flash, so no Orange upgrade will fix it. Too bad you flashed a rom with bootloader 1.06
Can you attach a usb monitor capture of the flashing process until you get the invalid vender id to confrm that?
I saved the Basic and Complete capture
Yes, it was what I said: your CID is corrupted. Bootloader 1.06 enforces CID checking and yours won't match any ROMs CID, it's just junk characters.
There are many of you with this same problem (search the upgrading forum), I hope someone comes with a fix for this soon...
ok, thx for the help.
indeed i really hope someone has a fix soon....
where to get UK Rom
Is there any way to get the UK Orange Rom anyway?
hi guys,
trying to upgrade the radio rom, im using the customRUU and its getting to about 99% and then its getting the error 290: invalid command.
and now it only boots in the red, green, blue and white bootload screen.
heres some info if it helps:
SPL-1.42.HSPL on my hd2..
windows 7 home premium, (i tried running as admin, no difference.. also tried several other usb ports)
help would be appreciated!
thanks guys!
have you tried a good ol MTTY or Task29 before flashing?
does the phone boot to RGD screen?
what Radio you using?
And you have the phone HSPL unlocked?
dodgy download perhaps? tried another radio?
did anyone find the solution to this problem??
l have same problem not upload any rom and radio tryed everything same eroor %8 and error 290 l dont know what is problem
webiso said:
l have same problem not upload any rom and radio tryed everything same eroor %8 and error 290 l dont know what is problem
Click to expand...
Click to collapse
What exact ROM versions have you tried, and what SPL or HSPL do you have showing in bootloader? Also is there a radio currently on your HD2 and what is that radio if so?
normally phone hd2 leo and italy not t mobile ant spl 208 hardspl maked bootmode okay ( also write boot with jtag ) radio ver 2.15.50.14
webiso said:
l have same problem not upload any rom and radio tryed everything same eroor %8 and error 290 l dont know what is problem
Click to expand...
Click to collapse
I had the same problem. I was trying to restore my phone to original firmware, due to issues with custom firmwares. I had managed to extract the NBH from the installer provided by my carrier, and used CustomRUU to flash the phone, but the phone was not booting.
I then flashed one of the EnergyROM builds onto my phone.
After that I could not get the original firmware onto the phone, error 290 at 9%.
I booted my phone into the bootloader (red/blue/green), and used HSPL2 to set SPL to 1.42.HSPL. I could then flash the original firmware.
My phone is now working fine, as best I can tell.
Always showing bootloader screen with rom upgrade error
I was trying to revert to windows custom rom from android (due to frequent freezing) and then onwards booting the phone I am always getting the bootloader screen displaying rom upgrade error.
I tried hard reset but still the same problem persists, then I downgraded the HSPL 2.08 to SPL-1.42.HSPL and then tried reinstalling the custom rom but still the same problem persists. In between after downgrading the HSPL, I tried task 29, it was unsuccessful after 96% (shows Invalid Command (Error 290)), while reinstalling the customRUU I have, I got something like error 270 at the end (it goes fine till 100%).
I also tried with installing the radio (ver 2.15.50.14) in between but to no effect
Please help me in fixing the issue, my phone is of no use now
Hi guys i read all the posts about the radio and no clues....
i flash a stock rom and after one day the phone died.
I tried with another ROM,stucks at 0%,with the card method the same,if i try with hspl same,task 29 same,change radio same....
What should i do?
How can i manage to change the Radio ROM? i think this is the problem cuz when i use card method,gives me error RSA.....
GSM Problem
i have a problem sinch i flashed the origional wm6.5 stock rom with an andriod rom for the first time, i went back to windows rom but GSM only Rdio does not work, when i choose 3G only, i have 3G Signal, but again a week signal, i do not know what to do, i flashed latest radio, still the same. At the same time Camera does not work. Camera HW is ok because it works under android. please help!
Please Help ! I read lots of pages in forum, but can't find what I'm doing wrong. I want to get HSPL working to able to instal custom ROM to use Nokia apps, witch are way better than HTC and Marketplace apps.
Phone, HTC Radar 4G T-Mobile US
Windows Phone 7.8 (pushed on update with seveneight tool)
OS Version 7.10.8858.136
Firmware vers. 1600.2200.20402.531
Hardware revision: 0002
Radio vers. 16.23.05.13_16.30.00.23U
Radio hardware vers. 2.16.0.D4
Bootloader vers. 2.5.160015.3(137079)
Here is what I did, I flashed using Goldcardtool with Y-cable, OMEGIMG.nbh. I think flash did not finished properly, it went too fast, phone rebooted to SPL , plugged in to PC used DFT_HSPL_WP7SG1_INSTALL, install finished OK , but when I boot up to HSPL mode it does NOT connect to PC.
(Using ROMUpdateUtility getting connection error (260))
Here is how my screen looks in HSPL mode;
PI06110
HSPL2.5 1600.3(137079)
eMMC SMS 7376,FA31
CotullaH(F:80,ID:10,V20,B:AA)
Radio-16.23.05.13_2
F400
Please Help, what I'm doing wrong ? Why my HSPL have F400 error ?
Thank You so much !
Problem fixed. After HSPL install needed second time boot to USB Host mode and this time radio installed correctly. All good now, time for custom ROM
newappz said:
Problem fixed. After HSPL install needed second time boot to USB Host mode and this time radio installed correctly. All good now, time for custom ROM
Click to expand...
Click to collapse
Flash the radio also.