Related
Hi guys. I've been here for while and over the years i flashed my hermes with various cooked and original roms over and over again. However, today i tried to flash it with the josh Manila2D_Black_V14_WWE rom to see if i could let go my iphone 3g and get back to my good old htc. Here's the thing: USB=Plugged, ActiveSync Ok, HardSSPL, Unlock Sim, the works... When i clicked RUUWrapper.exe all the process turns out good and then, puff! My screen turns black, the Led doesnt work, cant get it reset or hard reset, pulled out the battery and back in, nothing! then i took the USB PC cable and put it on wall charger. The led shows RED, the screen is dead, nothing happens. It stood there for a while, then i tried to hard reset. Went to bootloader, "Press R", "Then Space" "ok", PUFF! nothing happens. Cant get it sync with my pc, wont boot with hard reset, screen's BLACK, now the led stays GREEN all the time when i replace the battery...Can anybody help me out?! If theres a sollution im sure i'll find it here. Thanks in advance!!!
If you have Hard SPL V3 on the hermes, try to go to bootloader, Hold power, OK button and reset with stylus. Hold in all buttons until you get to tri-colour screen.
If you can get to bootloader then use the sd method to flash a different rom.
1. Format an sd card to FAT32, copy the .nbh file onto the sd card and rename to hermimg.nbh.
2. Put sd card into hermes and reset to bootloader.
3. Follow instructions.
cheers...
Still nothing...
Thanks for the reply Ultra Well i tried the Power+Ok+reset but nothing happens, the god damn green LED just stays on forever. However i can get to boot with power+the 2 quick buttons from the windows and ok. Can i get access to the SD Card from here? Havent been updated for quite a while, any particular rom you may suggest? Looking for stability, speed and cool home screen... I really apreciated your answer man, thanks
Finally the Cure!!!
It is only fitted that i respond here the cure i´ve found once again in XDA-Dev.com for another serious mind blowing problem with a Herm200. After days and hours spent reading the forum, testing some possibilities, finally the solution. Well it appears that with a SPL 2.30, that doesn´t bootloads by itself or with a SD Card; does NOT recharge the battery, no RED Led whatsoever... the simple official ROM solves the case. I entered Boot Load Mode with side ok+power and stylus reset, appearing USB Mode when i connected it to my PC, NOT showing the connection in ActiveSync, however the USB blip did in the PC. So i knew it was connected, plus the "USB" written in the Hermes. I´ve tested with almost every ROM available in the XDA-Dev, ran to 1% then, crashed. Then i managed to dowload the Official Windows Mobile 6.0 from DOPOD WWE. Fortunatly, it passed 1% to 100%, reviving my good old HTC Hermes. Hope this information helps for anyone with a similar problem.
Cheers!
Manu
Hi, I`m having some serious issues when trying to flash my HERMES. As far as I can tell, it is SIM Unlocked, but not sure if it`s CID unlocked. it`s SPL-1.06, and I can't seem to get it to install HARDSPL. I have tried, and tried and tried and tried. I've tried flashing VIA SD-CARD, but it just says "LOADING" and displays a number at the top, then goes back to the bootloader screen.
When I am flashing via the wizard, it'll go into the bootloader screen, and the wizard will fail saying it cannot connect "CONNECTION ERROR"...
I am at my wits ends, and cannot figure this out for the life of me. I have had 3 TYTN's now, and this one has gotten the better of me. I was able to flash both of my other TYTN's, but unfortunately I got the WSD, and cannot repair them, they are both beyond my technical knowledge of repairs...
PLEASE PLEASE PLEASE PLEASE PLEASE help....
Trying so hard to get this done...
Copied the .nbh (ren to hermimg.nbh) to my SDCARD and reset into bootloader, as I said, it just came up "LOADING" then back to bootloader....
I'd rip my hair out if I had any..
any help would be appreciated..
***UPDATE - I don't know what the hell happened, but suddenly, this bugger is letting me flash VIA SD. It's a damned miracle!
Just out of the blue, it asked me to flash via SD in the bootloader. Thank goodness! After 3 hours, I finally got it working..
Cheers all!
if you need more info, just ask, I will provide all I can....
need help ,during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
IPL 1.01
SPL 2.03
my device freezed at loading screen .
Now ,when i tried to rom upgrade in bootloader mode , using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
Edit/Delete Message
TVincent0621 said:
need help ,during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
IPL 1.01
SPL 2.03
my device freezed at loading screen .
Now ,when i tried to rom upgrade in bootloader mode , using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
Edit/Delete Message
Click to expand...
Click to collapse
Okay, when you're in the "bootloader" method, have you renamed the file that you're trying to flash "HERMIMG.NBH".
also, try to use the "stripped" AT&T ROM first, see if that'll help correct the issue.
Did you flash that first before you attempted to flash a different ROM on your Hermes? I've read in many different posts that it is highly suggested to flash that first then flash your ROM to your Hermes.
Should always flash via SD-Card, not recommending flashing via USB Wizard.
Try the "stripped" rom first, on a formatted (FAT32) microSD card, and see if that helps.
Cheers
i have download the "stripped" AT&T ROM ,it also the same ,when using USB method ,it stuck at 1% and my devide reboot .
when using SD card method ,it show (loading ...) about 2 second ,then it will back to tri-color mode there .
TVincent0621 said:
i have download the "stripped" AT&T ROM ,it also the same ,when using USB method ,it stuck at 1% and my devide reboot .
when using SD card method ,it show (loading ...) about 2 second ,then it will back to tri-color mode there .
Click to expand...
Click to collapse
I had that exact same problem.
I noticed that I hadn't named the file properly.
It's HERMIMG.NBH I kept putting in HERMING.NBH. It's kind of funny, but it's an easy mistake. When you boot with the "HERMIMG.NBH" it should flash. I used the HARDSPL V7, which can be downloaded at http://forum.xda-developers.com/showthread.php?t=296722, which is a "sticky" for this forum. Try flashing that one. Also, double check your .nbh file, make sure it's HERM IMG not HERM ING
That was the problem I was having too, it would just show "LOADING" and a bunch of numbers then drop to the bootloader... Then all of a sudden... "POOF" it worked, after I double checked the file and noticed my spelling error.
Now, if you have that fixed and still getting the error, it might be something else. I'm not sure how to exactly fix that, but as I said, mine was just a minor spelling error.. The exact spelling that I have, don't know if it is case sensitive, is "HERMIMG.nbh"
if it is case sensitive, that could also be a minor issue.
try it, if it works, then bingo, you're back in business, if not, then I'm not sure how else to fix it.
Cheers!
>.< ,now i type correct word "HERMIMG" ,it shown loading ... and (00068002) on the top of loading ... ,now it ,have better improvement ,it show loading ... for about 5 second only jump back to tri-color there ,izit this is the normal procedure ?
TVincent0621 said:
>.< ,now i type correct word "HERMIMG" ,it shown loading ... and (00068002) on the top of loading ... ,now it ,have better improvement ,it show loading ... for about 5 second only jump back to tri-color there ,izit this is the normal procedure ?
Click to expand...
Click to collapse
Okay, we're getting there. But still a long way off from it working as it should.
Okay, do you know if your phone is HARDSPL?
If you haven't already HARDSPL your phone, you should download that and try to flash that onto your phone.
Also sounds like it isn't SUPERCID. You'll have to CID unlock your phone, which is a good possibility as to why it isn't accepting other ROMS.
If your phone responds to the flash wizard when you download a ROM then get the SUPERCID and try to flash that one first, then move on to the HARDSPL.
For the SUPERCID, and my previous post has the HARDSPL.
At least the situation is improving, and your phone is starting to respond.
We'll get it working!
The HARDSPL you have to follow most of the "manual" installation instructions, and copy, then rename the "HermesUnlocker_v3a.nbh" file.
Try to flash that file, and we'll see if we can get it going.
Cheers
i think my phone not yet HARDSPL ,can you guide me to do this ?
i search the web ,it show me to here "http://forum.xda-developers.com/showthread.php?t=296722" izit correct ?
and also superCiD:
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button.
how i wana do the step 6 ,my phone is stuck now ,i cant log in at all >< ,but i try step 1-5 ,it also shown the 00068002
TVincent0621 said:
i think my phone not yet HARDSPL ,can you guide me to do this ?
i search the web ,it show me to here "http://forum.xda-developers.com/showthread.php?t=296722" izit correct ?
and also superCiD:
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button.
how i wana do the step 6 ,my phone is stuck now ,i cant log in at all >< ,but i try step 1-5 ,it also shown the 00068002
Click to expand...
Click to collapse
Attached is the HARDSPL file, already named "HERMIMG.nbh, which you just need to copy onto your SD-CARD.
When those are successful you will be able to flash any rom you want (provided it is as Hermes ROM)....
But as of right now, your phone is NOT bricked. It just currently has no ROM on it.
Have you tried to HARD-RESET your phone?
That's the two soft keys at the bottom of the phone, above the SEND and about the END keys.
Press and hold BOTH of those, then press the "RESET" button on the bottom of the phone. That'll hard-reset the phone.
I'm not saying to do that, just asking if you've tried that option yet.
Good luck, let me know how it's going.
Cheers!
my problem has solve now ,i try to install original rom for the phone ,it work ^^ ,thank for your help ,nice to meet you my friend from oversea .
Now i afraid to change any new rom >.<,can you guide me the best way to upgrade the rom ?so that i wont face the same problem and also brick my phone .
TVincent0621 said:
my problem has solve now ,i try to install original rom for the phone ,it work ^^ ,thank for your help ,nice to meet you my friend from oversea .
Now i afraid to change any new rom >.<,can you guide me the best way to upgrade the rom ?so that i wont face the same problem and also brick my phone .
Click to expand...
Click to collapse
Glad the problem was solved, and very happy to help!
Absolutely I can.
First thing is first, we have to SUPERCID unlock your phone, and we have to HARDSPL your phone.
Run the HARDSPL first, because the wizard will actually temporarily superCID your phone, so that you can install the HARDSPL, which will help prevent you from ever bricking your phone.
with your phone plugged in for activesync, you have to run the "autounlocker.bat" file in the SUPERCID. What this will do is make your phone accept other custom ROMS, whether it is from another carrier, or one of the ROMS that someone has developed on here.
After this, I would highly suggest, that if you ever flash your phone again with another ROM, do it the "SD-CARD" way. I'd only use the wizard to flash the HARDSPL and the SUPERCID.
Let me know how it goes.
Cheers!
Hehe ,My friend ,i had flash my phone with WM6.5 rom ,my device was Dopod838pro ,it is old device ,for my opinion WM6.5 not so suitable for my device ,but WM6.5 look amazing >.<
heh! Nice! Well sounds like your phone is now back amongst the living! That's good news! Hope you have many years of enjoyment with your phone!
Glad to have been of help for you!
Cheers
heh! Nice! Well sounds like your phone is now back amongst the living! That's good news! Hope you have many years of enjoyment with your phone!
Glad to have been of help for you!
Cheers
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
TVincent0621 said:
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
Click to expand...
Click to collapse
Unfortunately, no, I don't. You'd have to get a Vanilla, or a "lite/ultralite" rom. That's about the best I can suggest, unfortunately with the hermes, it does have a smaller ROM size, and limited RAM compared to the new, more up-to-date modern phones, like the 8925(Kaiser), or the new Tilt 2..
Cheers
TVincent0621 said:
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
Click to expand...
Click to collapse
Unfortunately, no, I don't. You'd have to get a Vanilla, or a "lite/ultralite" rom. That's about the best I can suggest, unfortunately with the hermes, it does have a smaller ROM size, and limited RAM compared to the new, more up-to-date modern phones, like the 8925(Kaiser), or the new Tilt 2..
Cheers
use the [Easy Hard-Spl v7 beta v0.1] by qwasde2
it,s really usefull i tryed it,s by me
it,s for win XP and vista and se7en users
i,am not joking here is the link
http://forum.xda-developers.com/showthread.php?p=5136858#post5136858
Hope you dont mind me reviving this thread as I also need your help
I tried flashing the MrDSL's WM6.5 ROM to my Hermes. Of course I followed the direction, I have Hard SPL (ever since Schaps rom) and stripped ATT flashed first.
However when I started flashing this rom, when I reached about 5% on the progress bar, I keep on getting Error. I followed the Recovery Steps and luckily I get the Tri-color mode and the process says Recovery successful. I then proceeded with the flashing but still getting errors, then recovery, then continue, then error again. Its been 10th try now.
Finally I canceled the update but I can only get the tri-color screen. Tried to Softreset as well as Hardreset but no go....my screen only gives me the Tri-color mode.
Any advice please....
thank you very much...
EDIT.....
problem solved sorry for that post.
what I did was:
1. flashed again the stripped ATT ROM....success!
2. flashed again MrDSL's WM6.5 titanium ROM (titanium)....success!
Dopod 838 Pro working again!
thanks again!!!
Bootloader shows but phone won't flash
Hey everyone,
I'm not new to
flashing my Hermes.
I'm just having an
issue I've never ran
into and can't figure
out. I would
appreciate some
assistance.
The strangest thing
is happening to me
while attempting to
flash from my
storage card. I put
the phone in
bootloader mode
and it takes
(IPL-1.04 /
SPL-2.10.olipro).
Then on the bottom
Serial shows and it
never goes to the
next step and ask
me do I want to
flash the new image.
I put the att original
on the 2gb storage
card over and over
and over and
renamed it
HERMIMG.nbh over
and over and over
and just am
flabbergasted. The
phone is not bricked,
it just refuses to
flash again.
Does anyone here
have any solutions
or suggestions?
PS - I have
formatted the card
to fat32 and I have
checked it for errors.
The HERMIMG.nbh
file is on the root of
the storage card.
Hi
When I turn on my phone all it shows is red, green, blue and white stripes across the screen with the following text:
ROSE100
SPL-1.54.0000
MicroP-Rose (LED) v10
MicroP-Rose (key) v5
PCBID 0x80
RID 0x0
At the bottom of the screen it also says "Serial", but displays no actual serial. Please see attached pic.
Please help guys. Problem initially started when phone collected dew on cold morning (camping).
Thanks!!!
You seem to be in the "flash screen".. I did that on my phone by accident, pressing power and one of the volume buttons.. Try pulling the battery out, put it back and see if it starts normally.
I have the exact same problem. Mine happened all of a sudden for no reason after turning my phone off and trying to turn it back on. Please post if you find a solution
Well, you can try to reflash your ROM. Many official ROMs can be found here.
Hi, I got the roms, but where can I read how to put the new one on my phone using my computer?
Ok, I got it I just run the .exe file to update my rom. However, there is just one problem, it says you should connect activesync to your phone. How tf do I connect activesync as my phone does not load any OS?! I tried without activesync but it doesnt work - it freezes on 0% update and after a while it runs some kind of recovery steps. So how do I get pass the activesync thing? Thanks
You can't upgrade ROM via activesync if u don't have acces to windows mobile, you can do it only from SD card.
Here http://www.megaupload.com/?d=M7OEOF2N (pass: xda) you find a Rose service manual and at the page 45 you find "ROM Image upgrade thru SD card" ...it's not complicated, read carrefuly.
Ok I read it but when I press the power button for the second time it says "No image file". I renamed the file to RoseIMG.NBH. What am I doing wrong?
I don't know what are you doing wrong ...try to rename the file to "ROSEIMG.nbh". Where did you download the ROM? ...I recomend you to put the same ROM you have on device because you don't have installed HardSPL (and I don't know if you can install it from SD card). Here http://forum.xda-developers.com/showthread.php?t=599520 are the officials roms for S740.
PS: I never tried this method on S740, I do it once on tytn II and works perfectly.
Here is how I got it to work:
Left it in the boot mode with the colorful screen until the battery is decharged enough, then tried to put it on again and it automatically turns off. So I put the USB cable in it and walla it started loading the battery and it turned on automatically and loaded WM. However, I still can not flush my ROM even through activesync.. but I am glad I can use it again.
something many forget with this fault, and I have seen quite a few is it is often not a rom issue but a hardware problem... in this case it may be a faulty up volume button, or maybe the plastic cap has shifted keeping the button held down, does the button still click ok?
The monet was a swine for the camera button giving up the ghost and doing nothing but dropping to boot loader......
Hi,
I have a problem with my HTC HD2, thing is that the phone it's not booting correctly, all i got when i power on the device, it's an emty white screen... without the green HTC letters.
I got installed a cooked ROM, BsB Beast 6.1, with radio 2.12.50.02_2, and i was running Android from SD when all this **** started, two weeks ago. The phone battery ran out while i was on Android, a couple of hours later... i got home and plugged the phone for charging. When i pressed the power button, the phone boots with that blank screen.
I can get into the bootloader, and it's showing this info (whitout the underscores):
PB81100 HX-BC
SPL-1.42.HSPL XE
_____________0x05
_____________0x30
CotullaHSPL
I've tried many different things and none seems to do anything at all:
- First of all, i did a hard reset. The process ends OK but the phone stays doing the same
- Then, i tried to flash again the same ROM i was using. I was unable to do that by using CustomRUU and PC connection. The phone it's detected by the PC, and the bootloader screen shows that it's conneted by "USB". Then, i executed the CustomRUU app, following all the steps and, when the phone should start flashing the progress bar doesn't get past 0%, both the phone display and PC. After a few minutes, CustomRUU gives an error saying "timeout" connection. I've tried to do this from different USB ports and different PCs with the same result.
- After those fails, i tried to flash again the cooked rom from SDCARD. The process ends OK, saying "Update Complete". Then, i rebooted the phone but the blank screen remains the same way. That cooked ROM doesn't have radio.
- After that, i decided to flash a stock ROM. First, i tried to make a "Task 29" to the phone, but i got the same problem than with the cooked ROM. The progress bar doesn't get past 0%. With the stock ROM the problem was the same again. Then, i tried to flash the stock ROM from SDCARD. The process stops at X% saying 0018003 RADIO - FAIL. I've got this error each time i try to flash a ROM with radio or a radio itself.
- I was able to do a "task 29" by using MTTY, but nothing changes when i try to flash any ROM after that.
- i've tried to upgrade my HSPL, by using both HSPL2 and HSPL3. Both programs detects my version of HSPL, then the process starts and ends saying "Succesfully done" but nothing changes in my bootloader, it's still saying that i got 1.42.HSPL
Since i can get to the bootloader, i hope to have any chance to get this device back to life.
I've readed some posts here and within other forums, i've tried with many different cooked or stock ROMS but nothing works
I hope to find help here, thanks in advance and, sorry if my speaking it's not 100% correct
yet another "i was running android and...........now my phone won't boot".. thread. makes me glad i don't bother with android...tried it once and had to hard reset, never touched it since, heh.
for the sticking at 0%,and timeouts etc, try and always enter bootloader yourself, then wait for serial to become usb, and then run customruu. this way you can also visually confirm hspl is there(or not there, depending what you are doing) and it should cure certainly the timeouts.
if i were you, i'd concentrate on getting back to stock, and start over.(only skimmed your post, i'm mobile, so sorry if i say something you already did.)
get into bootloader, get rid of hspl if it s there,(run hspl2 and choose 1.66.0000) then back into bootloader(you should soon get used to holding vol down as each stage completes to reenter bootloader) then try flash your CORRECT stock rom via usb. if that fails try it using the sd card method.
Thanks for answering, samsamuel.
I haven't looked into the Android section for threads with the same problem i got, maybe i should have started that way
Each time I enter the bootloader, i'm doing as you've said (believe me... in these days i've become a "master" on pushing power button with vol. down )
I always wait for the bootloader to finish loading, then i plug the phone to my PC, wait again for "Serial" turns into "USB" and, then, start the flashing process.
I'll try to do what you said with HSPL2, to select 1.66.000. Each time i've tried with different HSPLs, i've selected 1.66.HSPL or 2.08.HSPL... so, i guess i should try with that.
I'll be updating this thread as soon as i got news.
/me edit
I must to say, that Android was running "fine" (some minor problems when trying to wake up the phone, but nothing critical apart from this disaster). By the record, i didn't have installed dual boot... the phone always boots into WinMo
Hi again,
I have tried to update my SPL to 1.66.000 without success, despite what HSPL2 says ("Succesfully done")
Any thought about this? I can't understand why those programs are saying "OK" but are doing nothing
thanks in advance
not seen it first hand but have read several threads where the update seems to work but nothing changes. not really sure as to cause or cure, sorry.
I wonder if is there a way to make HSPL2 / HSPL3 to leave traces or any log of what they are doing... in order to see why my phone is ignoring them
Little bump, looking for more help
Is this the right subforum to post this things?
hey guys ...
there is the whole story
My friend's HD2 device was working in strange way, When restarting it gives a white screen and the HTC logo and freeze at this screen and then after a large number of re-starting it works, but when re-restart it again it return to the white screen
After a Hard Rest through the sound buttons the top and bottom were formatted but the device remain standing at the white screen after a Hard
the only solution to me was upgrade to new Rom and after read in the forum that This problem can be a lack of Compatibility between the Rom and the radio, but I think that the device had not been updated b4 by a lack of awareness of my friend, and then check the SPL version ,it was 1.42.000 (still locked) then try to ulock it by HSPL2_RUN as posted in some thread
it done right and the message "we hacked .." and enter boot-loader and checked it became 1.42.spl then I tried to upgrade by the following Rom:
RUU_Leo_HTC_WWE_GCC_1.43.488.1_Radio_Sig ned_15.26.50.07U_2.04.50_22_2_Ship
When updating the device whenit reached 9% did not complete the upgrade untill the upgrade process stopped by itself so I did restart the black screen appeared within a triangle inside the exclamation point.
now I started to be panic, and then search the net and found the advice from someone to use Task29 before the upgrade and when I run the program worked fine and after restarting the white screen returned with the HTC logo inside
I tried again to upgrade the same Rom and returned the same result ,searching again and found many advise to upgrade the SPL to version 2.0 which is recommended by most members
After the successful conversion of the SPL took off the device and swithched to boot loader to make sure the validity of conversion and the back of the version then after restating the white screen appeared and when I tried to reboot again the device turned off, I tried several times and did not work I said maybe the battery and when i connect the charger it did not ship and the orange led did not spark, tried the USB method but same result
I tried another charger and a another usb cord and it did not work and I check the battery by an electronics specialist, He assured that the battery is fully charged.
And now the device does not function at all, not even shaking when running and screen or charging
please guys i need ur argent assistance ...even a thought may help
Note: This is not the first time for me unlocking and flashing thin , my last devices was: JAM - k-jam - Jazjam - Omnia (current)
king roro said:
hey guys ...
there is the whole story
My friend's HD2 device was working in strange way, When restarting it gives a white screen and the HTC logo and freeze at this screen and then after a large number of re-starting it works, but when re-restart it again it return to the white screen
After a Hard Rest through the sound buttons the top and bottom were formatted but the device remain standing at the white screen after a Hard
the only solution to me was upgrade to new Rom and after read in the forum that This problem can be a lack of Compatibility between the Rom and the radio, but I think that the device had not been updated b4 by a lack of awareness of my friend, and then check the SPL version ,it was 1.42.000 (still locked) then try to ulock it by HSPL2_RUN as posted in some thread
it done right and the message "we hacked .." and enter boot-loader and checked it became 1.42.spl then I tried to upgrade by the following Rom:
RUU_Leo_HTC_WWE_GCC_1.43.488.1_Radio_Sig ned_15.26.50.07U_2.04.50_22_2_Ship
When updating the device whenit reached 9% did not complete the upgrade untill the upgrade process stopped by itself so I did restart the black screen appeared within a triangle inside the exclamation point.
now I started to be panic, and then search the net and found the advice from someone to use Task29 before the upgrade and when I run the program worked fine and after restarting the white screen returned with the HTC logo inside
I tried again to upgrade the same Rom and returned the same result ,searching again and found many advise to upgrade the SPL to version 2.0 which is recommended by most members
After the successful conversion of the SPL took off the device and swithched to boot loader to make sure the validity of conversion and the back of the version then after restating the white screen appeared and when I tried to reboot again the device turned off, I tried several times and did not work I said maybe the battery and when i connect the charger it did not ship and the orange led did not spark, tried the USB method but same result
I tried another charger and a another usb cord and it did not work and I check the battery by an electronics specialist, He assured that the battery is fully charged.
And now the device does not function at all, not even shaking when running and screen or charging
please guys i need ur argent assistance ...even a thought may help
Note: This is not the first time for me unlocking and flashing thin , my last devices was: JAM - k-jam - Jazjam - Omnia (current)
Click to expand...
Click to collapse
Hi,
Since you have enough experience in flashing custom ROM, I would suggest you the following ways:
1. Make sure battery is at least 50% and the battery pins are not bent
2. Format your micro sd card to fat 32
3. Find and download the CORRECT STOCK ROM. You can download it from htc website if your hd2 is non branded, or you can download it from your carriers website if your hd2 is a branded one. Make sure the downloaded file is not corrupt due to download process
4. Extract the downloaded file using 7 zip or winrar. Find the file named: RUU_signed.nbh Then, rename it to: leoimg.nbh then copy it to the root directory of your micro sd card
5. Go into boot loader and follow the onscreen instruction. If therenis no hardware issue, it should work.
Good luck ...
thanks m8 but I've checked the pins and changed the battery with fully charged one ..
but it's no boot loader mode ... its completely off
thanks 4 ur support
Not offering solution, just an observation,,,, hanging at HTC screen and only occasionally booting, plus flashing hanging at. 9% is a bad sign, sometimes associated with a stuck radio, and/or/caused by thermal issues.
Try chilling the phone with stock nbh ready to go on SD card, in sealed bag in fridge/freezer for a while, then try to SD flash.
If flashing starts, (white screen blue writing) keep an eye out for "rsa radio fail" or similar.
if the flash goes well, but then later the problem returns, it's pretty conclusively hardware.
thanks buddy for the advise but as I mentioned b4 ...
the device doesn't boot anymore ... and yeah it's Hardware bug I think.
best regards