Related
Hi,
I tried to upgrade my Himalaya to the latest O2 image (.187) with the
instructions mentioned by DCS. Changed also with the hexeditor the file
to reflect the new operator id, and still have the country id error. Even
worse, the update aparantly started to work since it put my device in the
bootloader mode, and now nothing works anymore....
Anyone ? First of all, getting it out of booloader mode would already be
nice....
TIA !
Willem
Why not use er2003edit to change the operator instead of a hex editor?
This tool can be found on this forum.
Mark
Just try to chage operator etc. once again with er2003edit and then reflash it...
If it will not work, you can still fix it with SD card.
buzz
tried to uppgrade my device. upgrade failed.
On rebooting i wont go into bootloader mode, the blue led will just flash.
Is my device beyond rescue???
markutah said:
Why not use er2003edit to change the operator instead of a hex editor?
This tool can be found on this forum.
Mark
Click to expand...
Click to collapse
Hi Mark,
Tried that, changed it to CDL and WWE as seen in the file DeviceData
and tried again, same error again. I have the 1.06 bootloader, so I cannot
use SD-Card images... (as far as I understood)
Anyone any clues as how to get out of the bootloader screen ?
Willem
please check this thread:
http://forum.xda-developers.com/viewtopic.php?t=12618
buzz
buzz_lightyear said:
please check this thread:
http://forum.xda-developers.com/viewtopic.php?t=12618
buzz
Click to expand...
Click to collapse
Tried that, to no avail, thanks for the tip !
Solved the issue, checked with google for HimaUpgradeUt and found
a version that does not do the countrycode check... It was mentioned
by the person on that forum as a 'very last resort' method. Well, for me
it worked fine. Here is the link.
http://d.tachet.free.fr/utilrom/free/HimaUpgradeUt.zip
Regards,
Willem.
please anyone in here help me for my x01ht
1. i flash with HER_DopodAsia_AUS_1[1].30.707.4_1.20.31.10_WWE_Ship.exe
2. when it flash until 14% , it stop
3. i plug out cable and restart phone , now phone only can go into bootloader mode
4. in bootloader mode , it show
HERM IPL-1.01
HERM SPL-1.06
5. now i flash whatever file into this phone , it will show invalid vender id
6. please teach me how to do now all master
thanks !
file i try to flash
-RUU_X01HT_1.33.761.4_1.14.00.10.exe
-RUU_Hermes_DopodAsia_AUS_1.30.707.8_1.27.30.10_WWE_SHIP.exe
-HER_DopodAsia_1237074_1060010_WWE_SHIP.exe
all not work , will show invalid vender id
check the two stickies in this forum - bricked device and free unlocker. If you can run the unlocker, it will SuperCID your phone, if you can get that far.
If not, check out the bricked device thread - lot's going on in there.
Also, have you tried putting the ROM back on that was there to start with? Inalid Vendor ID is a failed check by the phone to match Phone CID with ROM CID. If you didn't fry it out, then you whould be able to put the OLD ROM back on. If so, you have a little more work ahead of you.
no unlocker not work for me , please teach me step by step what should i do ... thanks for your help
hanyean1 said:
no unlocker not work for me , please teach me step by step what should i do ... thanks for your help
Click to expand...
Click to collapse
Shamelessly stolen from one of pof's recent posts but still applicable...
10 READ(wiki)
20 READ(Hermes->forums->stickies)
30 READ(Hermes->forums)
40 IF (Questions?) GOTO 10
50 FLASH(Hermes)
LOL
Closing this thread as he already posted here:
http://forum.xda-developers.com/showthread.php?t=286755
Hi guys,
I need your help. You'd make me amazingly happy if you could solve my problem.
I have an Orange SPV C100 (french one) and I keep trying to flash wm6.1 (the one Blackdragon_860 has released).
My problem is : I can't flash that rom. The updating process crash at 4% and I get an error saying that the ROM is corrupted.
Do you have any ideas to help me ?
Here are some additional information taken from the Hard-SPL And Soft-Spl walktrough :
1. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device
Click to expand...
Click to collapse
I've done that alright
, hold camera and launch spl.lnk -
Click to expand...
Click to collapse
I've done that too.
you`ll see the white screen
Click to expand...
Click to collapse
I have no white screen. Instead a file named JumpSPL.txt is generated... Here is what is inside :
-----------------------
Comandline is: 0x10000000 \SPL.nb
SPL File: \SPL.nb
Jump Address: 0x10000000
kmode is 0
SPL file size: 524288 bytes
3. From the flasher folder run ROMUpdateUtility.exe and follow instructions to flash the Hard-SPL if needed. or you can flash *ANY* oxygen rom
Click to expand...
Click to collapse
I've done that too. I put RUU_Signed.nbh from wm61OxygenUpdate1.rar in the same directory than ROMUpdateUtility.exe
Before the flashing process itself, ROMUpdateUtility.exe tell me I going to flash the image version from 1.7.74.1 to : 1.01
Then I have a rainbow screen which says :
ONBL : 1.07.0000
SPL : 1.07.0000
Oxygen : IU
The flashing process start, then crash and 4%... Saying that image file corrupted.
One last information :
I got the same error with other ROMS. Here the list of what I already tried :
Blackdragon_860's rom, released the 11-05-2008
Standard rom, the one that comes with Soft and Hard SPL (weight about 641Ko)
A Russian rom, taken today from zfree (here)
I didn't tried the chinese one. But as edgeofthestring has eventually the same problem than mine, I not will go for this rom.
I tried to be as complete as possible... I truely need some help.
Plz plz plz hrlp.
Thx
Guigoui
Try first flashing this rom:
http://www.megaupload.com/nl/?d=6B0FDY24
After this hard-spl and than flash any rom you like
Always use rom loader from hard-spl and before flashing rename rom to RUU_Signed.nbh
i also tried to flash the file posted by you but after 4 % the phone reboots and the setup gives me the: " invaliv vendor id " message
Default
ok. may it works when you do it like this:
1. restart your phone
2. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device
3. restart phone, don't connect to your PC!
4. open total commander, hold camera button and launch spl.lnk
5. Do you see a white screen? if yes proceed if not it has no
point proceeding, flashing will fail anyway!
6. Now connect your phone to your pc using the usb cable
7. From the flasher folder run ROMUpdateUtility.exe and follow
instructions to flash the Hard-SPL
8. After flashing Hard-Spl, to avoid reflashing, use always use
flasher from hard spl and rename the desired rom to flash to
RUU_signed.nbh
Hope this will finaly work for you!
i have tried it, i have the wm6.1 chinese version rom and the hard spl is not working at all in this rom, i have tried it with total commander and after the white screen appears and i connect the phone to the pc it is nor recognized by the pc...
thx nemphis for helping me... but it just don't work.
Believe me I'm not numb. I can read and use my little brain... I think I tried everything (including throwing my device to the other side of my room). There is something that keep my device from displaying this f*****g white screen.
Just for the record, I repeat, I have a french blocked orange C100...
If someone has got in the same problem and finally sorted it out, plz share how.
Nemphis, thx again but I doubt I will ever have wm6.1... Anyway I give up, so I guess I will never have wm6.1...
By the way, I also tried the rom you advised but as you so rightly said "if not it has no point proceeding, flashing will fail anyway!".
Thx you all...
c u...
by by
Is your phone sim unlocked also?
When reading through these forums there also are people saying you still need this: http://www.imei-check.co.uk/
Or ask your operator for the sim unlock code, they should give it when your phone is more than 1 year old.....
Phone simunlocked today... gonna try again tonight... Hope it will eventually work this time... Last hope anyway...
guigoui said:
Phone simunlocked today... gonna try again tonight... Hope it will eventually work this time... Last hope anyway...
Click to expand...
Click to collapse
Was your phone "app unlocked" before begining ? I would assume it is necessary, but won't pretend I'm a guru...
Christophe - Lyon - France
@guigoui :
I had this same, white screen didnt appeared .. but after unlocking using this way: http://rapidshare.com/files/105133496/Unlock_HTC.rar.html you'll see it (after runing SPL.lnk with camera button pressed) all is working !!!
I've WM6.1 !!!
Thanks!
This sounds pretty good vovakk... I'll test your file tonight (because I had no white screen after having my device simunlocked)
I can't to stand waiting until tonight...
It WORKED !!!! Now I have WM6.1 !!!
Ok so here are some additional information that could be useful.
Be sure you have .net framework 2.0 or newer before starting the unlocking process (the file shared shared by vovakk) otherwise you would be stuck at the second step.
When at step 5, I'm not sure which profile is required but, for me, it worked with "No security".
Once you've done step 5, you'll get THE white screen when laucnhing SPL.Ink (I confirm). You can start flashing.
I've flashed several rom as nemphis told me to, and it worked. Here is the list in the right order, with some notes :
1. http://www.megaupload.com/nl/?d=6B0FDY24 (given by nemhpis) : takes about 2-3 minutes, when done, I believed that my device was dead because it took a while before the PIN screen showed. Don't panic, just wait.
2. http://rapidshare.com/files/65732449/hspl.7z.html (the original Hard-Soft SPL - created by sp3dev) : extract, don't change anything, just launch RomUpdateUtility.exe. Flashing process takes less than 1 second
3. http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar (THE Windows Mobile 6.1) : In the RomUpdateUtility.exe folder, just replace the original NUU_signed.nbh by the one inside wm61OxygenUpdate1.rar. Launch RomUpdateUtility.exe. Eveything else is like 1. except that my device rebooted fast without being stuck a while on the windows mobile logo screen. The device reboot, you enter your PIN and then welcome to WM6.1 !
Hope someone would find interesting to read my so long posts...
I thank you all for your patience and help... I wouldn't be able to do it by myself.
C you
hey GuiGoui can you upload this file here or Rapidshare please. Megaupload is way tooooo slow. RUU_OxygenWM5_1.5.401.2_R3_4.1.13.28_02.67.90_HTC_EUR_Test.exe
thanks
I can't.... 8Mo limited...
guigoui said:
It WORKED !!!! Now I have WM6.1 !!!
Ok so here are some additional information that could be useful.
Be sure you have .net framework 2.0 or newer before starting the unlocking process (the file shared shared by vovakk) otherwise you would be stuck at the second step.
When at step 5, I'm not sure which profile is required but, for me, it worked with "No security".
Once you've done step 5, you'll get THE white screen when laucnhing SPL.Ink (I confirm). You can start flashing.
I've flashed several rom as nemphis told me to, and it worked. Here is the list in the right order, with some notes :
1. http://www.megaupload.com/nl/?d=6B0FDY24 (given by nemhpis) : takes about 2-3 minutes, when done, I believed that my device was dead because it took a while before the PIN screen showed. Don't panic, just wait.
2. http://rapidshare.com/files/65732449/hspl.7z.html (the original Hard-Soft SPL - created by sp3dev) : extract, don't change anything, just launch RomUpdateUtility.exe. Flashing process takes less than 1 second
3. http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar (THE Windows Mobile 6.1) : In the RomUpdateUtility.exe folder, just replace the original NUU_signed.nbh by the one inside wm61OxygenUpdate1.rar. Launch RomUpdateUtility.exe. Eveything else is like 1. except that my device rebooted fast without being stuck a while on the windows mobile logo screen. The device reboot, you enter your PIN and then welcome to WM6.1 !
Hope someone would find interesting to read my so long posts...
I thank you all for your patience and help... I wouldn't be able to do it by myself.
C you
Click to expand...
Click to collapse
How did it work............ i ended up lockin my phone it was unlocked before... now no application works... anymore it say this application is not have signed certificates..... PLZ ANY1 HELP I DONT EVEN KNOW HOW TO HARD BOOT THIS HANDSET..... I NEED URGENT HELP PLZZZZZZZZZZZZZ...
Hi everyone.
im a beginner for PDA's..i have read your post about prophet then i decided to upgrade to WM6 PDAVIET.
While i connect pda and execute software i had mistake and turn off phone.i did turn on phone after cancelled process
it just showing operator logo and IPL SPL GSM OS infos..
and i have run again Upgrade_ROM.exe than its stopping " Clearing the existing Extension ROM " ..
What did i do PLS i wait your helps
goto bootloader and flash again
follow the direction on the link to enter bootloader mode
http://wiki.xda-developers.com/index.php?pagename=prophet_bootloader
and read the NEW WM6 upgrade guide. which is a sticky on top of the page.
Thank you..
i entered bootloader screen its showing operator logo and IPL SPL... vs
then i retry to run Upgrade_ROM.exe but there are no change ?
what must i see on bootloader screen ? and now my screen vibrating during on process now is it normal ?
PLS help ?
algorytma said:
Thank you..
i entered bootloader screen its showing operator logo and IPL SPL... vs
then i retry to run Upgrade_ROM.exe but there are no change ?
what must i see on bootloader screen ? and now my screen vibrating during on process now is it normal ?
PLS help ?
Click to expand...
Click to collapse
read my post @ my signature...... please reply to that thread if you think helpful~~~
algorytma said:
Thank you..
i entered bootloader screen its showing operator logo and IPL SPL... vs
then i retry to run Upgrade_ROM.exe but there are no change ?
what must i see on bootloader screen ? and now my screen vibrating during on process now is it normal ?
PLS help ?
Click to expand...
Click to collapse
That is not bootloader... It should show a three coloured screen, and when plugged in to USB, the text in the bottom right hand corner should say "USB"
WARNING - WARNING - WARNING
VERY IMPORTANT FOR HARD SPL USERS, YOU MUST "REMOVE HARD SPL" BEFORE PROCEEDING!
IF YOU DON’T REMOVE HARD SPL YOU WILL BRICK YOUR PHONE!
These Instructions assume your phone is in stock condition
Download and install “Wizard Service Tool”
Download "M3000v4aUnlock"
Download unlock file below
1. Make sure your device is properly connected to the PC through ActiveSync
2. Run Wizard Service Tool, click “Enab. RAPI + Unsigned Apps” button, wait for it to finish
3. Click “Repair IMEI” button, write down and save your original IMEI number before proceeding
4. Enter this number “356381000157184” as your New IMEI number then click “Write IMEI” button
5. After the phone reboots, turn the phone off and remove the USB cable
6. Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen
7. Start M3000v4aUnlock, when program asks for the .unl file, browse to and select "356381000157184.unl" wait for it to finish
8. When the phone has fully rebooted, start Wizard Service Tool, click “Repair IMEI” button, and change back to your original IMEI number
That’s it
Your phone can now be flashed with any G4 Safe ROM provided you have the appropriate ROM Update Utility
To flash cooked ROMs, you need the "Wizard No ID Update Utility"
To flash OEM ROMs, nothing special is required
WARNING - Changing your IMEI number is considered to be illegal in most if not all countries
Disclaimer - The above mentioned method is provided for informational purposes only, neither I nor xda-developers condone the changing of IMEI numbers
I have successfully used this on two G4 devices and one G3 device.
I found with the G3 device it also SIM unlocks, I assume it does this with the G4 as well, but mine had already been unlocked.
Just tried it and it worked!
Thanks
.unl file
-MyHTC- said:
This was originally posted in the [HELP PROJECT] "Data Crashes" Project [HELP PROJECT] thread, Page 25, Post #249
Instructions:
Download and install “Wizard Service Tool”
Download "M3000v4aUnlock"
Download unlock file below
1. Make sure your device is properly connected to the PC through ActiveSync
2. Run Wizard Service Tool, click “Enab. RAPI + Unsigned Apps” button wait for it to finish
3. Click “Repair IMEI” button Write down and save your original IMEI number before proceeding
4. Enter this number “356381000157184” as your New IMEI number then click “Write IMEI” button
5. After the phone reboots turn the phone off and remove the USB cable
6. Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen
7. Start M3000v4aUnlock, when program asks for the .unl file, browse to and select "356381000157184.unl" wait for it to finish
8. When the phone has fully rebooted, start Wizard Service Tool, click “Repair IMEI” button and change back to your original IMEI number
That’s it
WARNING - Changing your IMEI number is considered to be illegal in most if not all countries
Disclaimer - The above mentioned method is provided for informational purposes only, neither I nor xda-developers condone the changing of IMEI numbers
Click to expand...
Click to collapse
where is unl file???????????
Rooks said:
where is unl file???????????
Click to expand...
Click to collapse
Download and unpack 356381000157184.zip
I now have IPL 2.21.0001 and SPL 2.21
I forgot to undo HardSPL. Don't forget.
I cannot get past three colored screen.
I cannot flash anything over it.
It goes through the process, but after it reboots, it is still the 3-colors.
RoryB said:
I now have IPL 2.21.0001 and SPL 2.21
I forgot to undo HardSPL. Don't forget.
I cannot get past three colored screen.
I cannot flash anything over it.
It goes through the process, but after it reboots, it is still the 3-colors.
Click to expand...
Click to collapse
I have got exactly the same problem! I also forgot (or didn't know I have to) undo HardSPL. Is there some solution?
pszemaz
Wow i’m so sorry to see this happened this is something I was unaware of, it’s not mentioned anywhere that i’ve read.
I have corrected the main post to reflect this.
I have not been able to find a fix.
I could not get MTTY to work for me. I found Tera Term and tried it.
Info states 2.21.olip for the SPL and gives an error which I forgot and am having trouble reconnecting. The error had to do with CID. I am having trouble getting the phone to come back on. Must have used up the battery trying to figure things out.
Unfortunately, most everything I read leads me to believe I need to get some mortar.
I know this is a stupid question but did you try the Wizard Love ROM?
The only reason I ask is you say you still have the hard SPL.
I should have spelled out what all I tried. Yes, I tried wizard love ROM, original Cingular ROM and noidupdate utility with several nk.nbf files such as 2.25.0001 IPL/SPL, etc. It either works all of the way and reboots to the IPL/SPL splash, gives the no communication error or gives the wrong updater error. Once I got a wrong file error.
That doesn’t look promising.
Unfortunately I don’t have an 8125 G4 anymore so I can’t make a backup for you to try.
Maybe someone with an 8125 G4 could make a backup and send it to you, I don’t know if it would work but it would be worth a try.
Just an update. When I do a hard reset the phone states "Format is Failed" and goes to the first splash screen which is not my splash screen, but I assume it is from the unlock program.
I just unlocked my SPV-M3000 G4 phone and it works fine! Thanks!
RoryB said:
Just an update. When I do a hard reset the phone states "Format is Failed" and goes to the first splash screen which is not my splash screen, but I assume it is from the unlock program.
Click to expand...
Click to collapse
have you tried to softspl your device again as if it were hard SPLed? then flash in a stock rom? maybe that will help.
SoftSPL cannot see the device since it will not get out of bootloader mode
I have been continuing my research:
If someone has a Cingular G4 phone and is willing to take the time, I could use some help.
You would need to flash back to cingular ROM (and go back to locked CID) and then use MTTY command ( r2sd all ) to put your ROM image onto a clean SD Card. Then upload that image so I can try to use MTTY to flash back a working ROM.
Don't know if it will work, but this seems to be the only thing left to try.
RoryB, if you'll get that image plase remember to post it here, as I'm in the same situation as you. Thx.
pszemaz
I will definitely post the results here if I get one. If it works I will post step by step recovery method here too.
RoryB said:
SoftSPL cannot see the device since it will not get out of bootloader mode
I have been continuing my research:
If someone has a Cingular G4 phone and is willing to take the time, I could use some help.
You would need to flash back to cingular ROM (and go back to locked CID) and then use MTTY command ( r2sd all ) to put your ROM image onto a clean SD Card. Then upload that image so I can try to use MTTY to flash back a working ROM.
Don't know if it will work, but this seems to be the only thing left to try.
Click to expand...
Click to collapse
This is true however the phone will need to be CID unlocked no hard SPL.
The “r2sd all” command requires full CID unlocking.
The image can’t be remove from the SD card so it must be mailed to you.
-MyHTC- said:
This is true however the phone will need to be CID unlocked no hard SPL.
The “r2sd all” command requires full CID unlocking.
The image can’t be remove from the SD card so it must be mailed to you.
Click to expand...
Click to collapse
I was thinking that maybe the CID unlock worked (it seemed to go through full operation - no error messages), but corrupted the ROM since I get the "Format is Failed" message after a hard reset. I was hoping to try this as a last effort I could figure out.
I did not realize it was not a file that could be copied, etc.