Not sure what I'm doing wrong but can't get the radio ROM upgrade to run. Downloaded the 3.42.50 ROM (I'm on Verizon) and using Olipro 2.40 bootloader. Starts to run upgrade then quits and device restarts. Any thoughts?
unlock with nuespl
That did the trick. Thanks!
Sprint Mogul to Verizon?
Ive unlocked the sprint mogul and loaded dcd and added the verizon cab. But i cant get the radio to switch to verizons radio? any answers?
Related
So here is my situation:
I had a 3.27 radio with a 3.xx rom (one of the DCD roms). I wanted to get the 3.35 radio so i decided to flash to the SPRINT 3.35 rom, to do so i had to relock the phone so i used Titan Re-locker (which may have caused the whole problem) and now I am stuck at the SPL 1.06 screen.
I tried flashing older roms and still no luck.
I am currently with Telus and only flashed the SPRINT 3.35 rom to get the 3.35 radio off it. WHat do i do? I haven't bricked my phone right?
I have tried to flash Sprint 2.09 and SPRINT 2.17 roms and have failed. The bar goes up to 1% and then restarts the phone back to the SPL 1.06 screen for any flashes i try to do.
So here is my situation:
I had a 3.27 radio with a 3.xx rom (one of the DCD roms). I wanted to get the 3.35 radio so i decided to flash to the SPRINT 3.35 rom, to do so i had to relock the phone so i used Titan Re-locker (which may have caused the whole problem) and now I am stuck at the SPL 1.06 screen.
I tried flashing older roms and still no luck.
I am currently with Telus and only flashed the SPRINT 3.35 rom to get the 3.35 radio off it. WHat do i do? I haven't bricked my phone right?
Click to expand...
Click to collapse
Ok there's a WHOLE mess of problems with this post. First of all, if you read correctly in the kitchen thread, radio 3.35.04 is REQUIRED for any 3.x.x rom. 3.27 WILL not work. Second of all, you do not need to relock your phone when installing the 3.35 sprint rom, in fact, that's what caused it to break as the 1.06 bootloader will not flash or boot a 3.35 rom or radio. The only way to fix your problem right now is to flash the stock telus rom and radio using the microsd flashing method. Once that is complete, you need to unlock again with Olipro 2.40, and then run the sprint 3.35 update.
sux 2 B U. I highly doubt it is bt\ricked, you just dont know what U R doing.
This it what I did...
I did not need to relock. I started the sprint update with the phone booted up to the titan in Hard-SPL mode(miltucolor flash screen) . It reboots to the Hard-SPL several times to finish it and may pause several times. I just let it run. Keep an eye on it, it is done when it boots to a regular boot screen. Dont let it finish booting and then manually boot into Hard-SPL (PWR + Camera + reset with stylus) and flash DCD 3.0.4. I did the same process with the alltel update to get 3.37. You will be left with the bootscreens from the Sprint or Altel rom, but booting to DCD rom with 3.37 radio, GPS, exct....
I flashed both, same issue, no sound when dialing *228. If I try to turn on the speaker, it snaps and restarts. If I leave it going it will connect and about 30 seconds later it restarts.
Any suggestions?
More info please...... what were you running before? Have you unlocked the phone and upgraded the bootloader and radio?
I was running the stock rom before. I using the 3.27 radio and olipro 2.4 I did the bootloader, the rom then the radio. I unlocked the phone with Hard SPL 240. Do I need to relock?
You need to upgrade your radio to atleast 3.35.
yea get 3.35 or 3.37 radio
WAstarita said:
I was running the stock rom before. I using the 3.27 radio and olipro 2.4 I did the bootloader, the rom then the radio. I unlocked the phone with Hard SPL 240. Do I need to relock?
Click to expand...
Click to collapse
You need to read the ENTIRE section that DCD wrote in the 3.0.4 kitchen POST.... He clearly states you NEED the 3.35 or higher radio.... there are known issues with the "leaked, beta 3.27 radio" one of them is an audio issue....
You will only need to flash the SPINT or ALLTEL update. WITHOUT letting the customizations run..... Then DCD 3.0.4 will run fine for you....
I'd like to upgrade my VZW XV6800 to DCD's Titan 3.1.2 with radio 3.39.10, but have some questions. I've read the Wiki and FAQ several times through, but am having a hard time understanding the correct order of upgrading the radio and ROM.
I've successfully upgraded bootloader to 2.40 using Hard-SPL-MFG.exe
Do I next upgrade the radio? Or do I load DCD's 3.1.2 and then upgrade the radio? (After writing that out I think I would upgrade the radio...looking for confirmation.)
Radio or you will be screwed. I speak from experience. Get a SD card and use that method.
good advice on both accounts.
did the radio first, but was then unable to get past the bootloader and unable to connect w/ ActiveSync. followed the SD directions and now i'm running everything i wanted!
I Flashed ROM Then Radio
Tonight I just finished successfully flashing my phone for the first time. I updated the boot loader using titan_SPL_2.40-olipro.exe, then I attempted to update the radio but actually did not due to a mistake on my part, then I successfully updated the ROM to dcd_titan_3.1.2.exe. Upon a restart, I realized the radio was not updated based upon the Verizon splash screen so I re-entered the bootloader and eventually flashed the radio. Once I finished flashing the radio I restarted and was presented with WM 6.1 and a usable phone.
Easy Way
The easiest way i found was after the new bootloader to go and use the Alltel Stock ROM with the 3.39 radio. This will upgrade your radio without you having to call Verizon. Then load DCD's ROM. Again you should not have to call Verizon or mess with SD cards or anything.
The easiest way i found was after the new bootloader to go and use the Alltel Stock ROM with the 3.39 radio. This will upgrade your radio without you having to call Verizon. Then load DCD's ROM. Again you should not have to call Verizon or mess with SD cards or anything.
Click to expand...
Click to collapse
The Alltel rom has Radio 3.37.20, not 3.39.10.
schwillyd530 said:
The easiest way i found was after the new bootloader to go and use the Alltel Stock ROM with the 3.39 radio. This will upgrade your radio without you having to call Verizon. Then load DCD's ROM. Again you should not have to call Verizon or mess with SD cards or anything.
Click to expand...
Click to collapse
Also not everyone has to call Verizon. I have flashed once to stock, DCD 3.0.4 and DCD 3.1.20 and have yet to call or reenter anything.
I need a little help with this phone. I have a AT&T Tilt that I've unlocked and flashed at least a dozen ROMs and it's no trouble at all to use it on my T-Mobile account. My co-worker here has a Sprint Mogul that he wants to use on his Verizon account and I'm having trouble doing it.
I have installed Hard-SPL 2.40-olipro, Radio 3.42.50, and DCD 3.2.6. I also have a guy Verizon that will enter my ESN in their system. My question is How do I get to the provisioning menu and what are the Verizon settings?
I think it best to relock the phone by the following instructions. This should install a Verizon PRI and PRL. http://forum.ppcgeeks.com/showthread.php?t=21161
After you have the stock rom on and working flash the custom rom and the dcd carrier cab. Then add the esn or even add the esn while using the stock rom. Also update using *228.
After relocking the Sprint Mogul it woun't allow a Verizon ROM to be flashed.
Did you follow the instructions in my link I provided?
Ok I have SPL 1.20 loaded the verizon rom but I have no radio. I need 1.30.60. Looking for it now
The link I provided has the rom and radio included together. No searching needed.
splash screen says no radio.
reflash then because it is included.
Anyone encountered this error before? It gets to 8% and then phone reboots and I get this on my PC screen. It says Error [328] (see attached image)
I am using Radio 3.37.75 (verizon), and my bootloader shows 2.40 Olipro
Any ideas?
Try this RUU it is version 3.16.4.3.
Yes, thats the version that I am using. I think... when I run it, it says 3.16.4.3 in the window title bar. (see screen shot)
EDIT: I tried it anyways, and I got the same thing. Do I have the right bootloader? Would a different one help?
what are you trying to flash
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
wildcard said:
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
Click to expand...
Click to collapse
Just follow my post here and only use the files and Radios that I provide. Make sure you read a few times so you understand, and dont skip anything. Most important based on what I have read in this thread. Use only the radios I provide on my share site and take your time paying close attention.
http://forum.xda-developers.com/showpost.php?p=3687027&postcount=144
Thanks, I'll do it exactly like that. I will keep you posted. I have to get a new micro SD card, I only have an SDHC 8 GB
The radio can be updated via usb. I do it all the time. But it does hard reset the phone in the process.
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
I followed the directions exactly like in Ryan's post mentioned above, (used USB instead of SD card), and it works!
Fully functional. I used Radio 3.42.02 (somewhere I saw that it was recommended over the others, went with it to be safe). Then Flashed Ryan Mogul Rom 2.2 Heavy.
Thanks everyone!
drewcam888 said:
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
Click to expand...
Click to collapse
i have spl olipro-2.40, rom dcd 3.2.6 and want to upgrade radio to 3.42.50 using usb. should i downgrade spl to 1.20 before upgrade the radio? or i stick with current config and update the radio using RUU?
Still cant load radio
Obtained 6800 originally Alltel, not sure which radio, Had Olipro 2.40 installed, would hang on Alltel splash screen.
Could not get any RUU loads to complete (from USB or SD card), usually would fail around 50%.
Eventually was able to get RyanMogul 3.1 Cricket (lite) to load, but shows no radio and eventually screen goes blank. Never goes into active Sync mode.
We force boot loader mode and try and load several radios including Titan_Radio_ROM_3.42.50.Alltel.rar, Titan_Radio_ROM_3.35.04,
but keep Getting error 328 from RUU when I try to load a radio..
tried RyanMoguls "Here is a fix for GPS for all you VX6800 users that gps will not function!!", but cant run relocker because no active sync connection.
Stock Verizon ROM RUU also gets error 328.
Any ideas.