Related
hi
i have i-mate with bootloader 1.01, i was going to use chines WM2003 SE rom update by SD card, after putting SD and do flashing it says "failed" then i did a hardrest, and now i cant get bootloader screen...... i think my device gone be junk
plz help me if there anyway to reback it to life
thanks alot
hi nightmare,
that's really one SORRY situation. like a nightmare.
i know, cause it happened once to myself.
so, could you please describe what exactly happened, what is your XDA2 behavior now, can you connect with terminal, is the LED on while connected to charger or cradled...
i mean everything.
buzz
when i plug the device into charger there is no power LED, plus i pressed (power button + any directon + rest) and nothing apper (not even bootloader)
plz help me to get it work again.....
best regards and wishes
nightmare
...something similar happened to me. unfortunately i was not able to fix it myself.
so i sent it to repair. it was repaired under warranty...
interesting is, that they fixed it very quickly without even opening it.
there must be a way to do it... but how...
try to ask itsme from this forums...
maybe there is a way to boot it over eboot and upload new bootloader or talk to it with direct serial cable
good luck
buzz
thanks alot buzz_lightyear
yah smae here i was thinking about buying serial cable,,,,, :roll:
thanks for telling me it did happen to u lol
yeah...
it hapenned to me because i was trying to port W2kSE to XDA2 and i did forget to remove 2.06 bootloader out of the flash file...
as i said, try asking itsme. he knows probably the most here...
buzz
Dead XDAII with no screen
I have a situation like that before, goto http://forum.xda-developers.com/viewtopic.php?t=13651
Hope you get to recover your XDAII
good morning to everybody...
i have an xda I
my akku went off during my holiday. now i recharged it an the wallaby bootloader v5.22
starts an nothing else doesn´t start.... can anybody tell me how to start the windows mobile software?
thx 4 help
s3V3n said:
good morning to everybody...
i have an xda I
my akku went off during my holiday. now i recharged it an the wallaby bootloader v5.22
starts an nothing else doesn´t start.... can anybody tell me how to start the windows mobile software?
thx 4 help
Click to expand...
Click to collapse
Have you tried a hard reset?
Are you sure, you do not have an hardware problem? Normaly you enter the bootloader by pressing power button and making a soft reset. Maybe this switch is blockated by anything....
HTH
Stefan
yes i don´t think its a hardware problem because nobody touched it during the week of my holiday but i´ll go to the shop tomorrow looking they will say
oh and yes i did a few hard and soft resets... no effect... he only doesnt boot windows the bootloader starts but there i can only do selftests
please can any one tell me how to fromat Qtek 1010?? thanks in advance
XDA won't start
Dear forum users,
I own a XDA I, which is sold as PCT 206 in Turkey. The original OS is ppc 2002
I also have the same problem on my XDA 1. I used up the battery to the end and after plugging the charger I got the bootloader screen.
At that time a had a cooked rom ppc 2003.
I tried to flash from SD to the original ppc 2002 but I still get the bootloader after soft and/or hard resetting.
Does somebody have an idea.
Best regards.
Sounds like the power switch may be stuck if you are entering bootloader from soft reset.
same trouble
cruisin-thru said:
Sounds like the power switch may be stuck if you are entering bootloader from soft reset.
Click to expand...
Click to collapse
i have same problem, after i upgrade from SD card and after i gave a cold boot machine start with TMOBILE logo and: 4.0.1.16, R6.25.02, G324e4...
by the way... i have no more access to setup options at start... any idea about how to fix this?
Is there a way to access to RAM using IR or USB without init windows CE thanks a lot
lambertoh, you have a different problem, you need to reflash your phone using sd card method again, it might be helpful to try a different memory card.
cruisin-thru said:
lambertoh, you have a different problem, you need to reflash your phone using sd card method again, it might be helpful to try a different memory card.
Click to expand...
Click to collapse
thanks for your response, i did it fix unsuccesfully. I have no access to test menu (before i had in fact but i kill it ). Can you tell me how can i write the bootloader into the wallaby, maybe with a jtag, or maybe with a byteblaster cable, i don't know too much in thius kind of themes but i have to... Actually i'm trying building a serial cable and i pretend use tty application to try to use an terminal pda in the computer.
Excuse for the english, is not my native language.
any solution
;740211 said:
oh and yes i did a few hard and soft resets... no effect... he only doesnt boot windows the bootloader starts but there i can only do selftests
Click to expand...
Click to collapse
i am having this same problem ... i have a T-Mobile and it is stuck on Ozone screen i can run the bootloader but it allows only tests...
can anyone tell me a solution ?
if a valid rom is put on the sd card the right way entering bootloader auto update the rom
hi my friend my device is not respond i try to upgrade it but it is now black screen and i want to reflash it like any device
and i want to know how i can do that
please any one know
my device is
imate pocket pc phone
win se 1.72
and i want to know how i repaire it but you must know that i try to put in the crtadel but and reinstall but this is screen is appear to me
start aggain
what did you put in your rom?
first check everything
is the roms you try to update for your device?
it was power loss?
can you get it to bootloader if you can it will be back from the dead
check roms for country id errors
if you get it to bootloader and you dont get it to connect to you pc try another pc
ok thats it for now
my friend when i connected the power my device is not work how?! because when i put the battery in the device it gives me that no power in the device ,then i changed the battery but the problem still appear when i put the device in the cradel the red light becomes work but this happend when i put it without battery now when i put the battery the device turn off the red light and not give me any thing now i want to give the device power
how can i do that and how can i fix the screen that tell me that the device is not in the cradel this screen is apper for me my frindes
and when i press that buttons nothig happen i don't know waht but now i want to give the device the power how can i do that do you have any answer about that
hi my friends what can i do
hi where are you my friend what can i do
plesae why noboady replay for me
oh where are you
Did you try a hard reset? Please detail what happened exactly, from the beginning.
the first when i put the baterry in the i-mate pockt pc phone the red light is became off i don't know why if someone know the reason he can help me and i want to get the bootloader that is appear in the middel of the screen it called usb or serial because the screen is black i don't know waht i want to became on and i see the serial so can you help me my friend please
if you know how can i get the bootloader you will help me and how i turn on the screen my friend because it is became off and this is the reason
i hope you understand me because when i upgrade the device still work but when the extended rom is installed in the device i see (erasing the rom ) and after erasing the rom i have lose the power so the extended rom now is empty and the usb didn't read any thing by active syn and any other application so can you help me and i try to re-upgrade the processe is failing so i want to know ho can i turn on my device again
Hi everybody,
i've got a big problem with my s200 G4.
when i flash it ti wm6, it work about 1 day, and after it freeze.
since, i can't turn on it. When i plug the power supply, no LED :/
I try the battery on an other S200 (i've got 3 ) and the battery is ok.
Anyone got the diagram of the motherboard ?
Other idea ?
Hello
I have the same problem
Do you found the solution ?
lot of people have the same problem
Hi,
After open my S200, i think this is a capa out :/
Lot of people after upgrading the s200 have got the same problem. Freeze , reboot..freeze ....and never work again
Have you got a red led ? orange ?
charging ok ?
i had the same probleme
the solution is to remove the battery for 24 hour after plug it in the usb with ur computer until the charger leed appear
after change the rom to a wm5 rom and it will work perfectly.
i think the reason of this probleme is the ipl version must be 2.20 beafore upgrade to wm6
tried and failed :/
Hi,
I test your technic, but doesn't work. Now, when i plug the charger, i've got the red led 1 second, and ....nothing. it doesn't won't to switch on
i try the trick with the pins...but doesn't work
tried and failed :/
Hi,
I test your technic, but doesn't work. Now, when i plug the charger, i've got the red led 1 second, and ....nothing. it doesn't won't to switch on
i try the trick with the pins...but doesn't work
Hi,
Same problem, when I put the charger in I got one sec red led. But I can hard reset or enter bootloader, when on the charger, but there is no way to put USB when the charger is in. Which pins are + and - battery?
If any Prophet can enter bootloader, it can be recovered. See the wiki for a how to.
prophet with white screen and red led
hi everybody.
After trying again and again the pin trick, the s200 went to a blank screen, white with the red led.
I wish it reboot again...
if you got any idea to enter bootloader when i've got white screen ....
Can it enter bootloader? Hold down the camera button and soft reset.
the same problem
i have G4 with ipl and spl 2.20 and on switching on it freeses with white screen. it goes to bootloader, but except WWE ship 220 update others can't be loaded.
Sometimes it goes to screen "Windows mobile", but then freeses.
Is any solutions? Thanks
Jahn11 said:
i have G4 with ipl and spl 2.20 and on switching on it freeses with white screen. it goes to bootloader, but except WWE ship 220 update others can't be loaded.
Sometimes it goes to screen "Windows mobile", but then freeses.
Is any solutions? Thanks
Click to expand...
Click to collapse
Can you perform a hard reset?
no bootloader..just white screen
l3v5y said:
Can it enter bootloader? Hold down the camera button and soft reset.
Click to expand...
Click to collapse
I can't access to bootloader. :/
nyco said:
I can't access to bootloader. :/
Click to expand...
Click to collapse
Can you do a hard reset?
Yes i try again and again...but ...
white screen ( flashing )and red led :/
snif snif
Try to enter bootloader (soft reset and camera button), it doesn't matter if it shows nothing, disable activesync connect through USB, and try to flash a WM5 ROM.
Ok, i'm trying it this evening...
But when i plug the s200 on my PC, nothing show the phone is connected (USB mode on winXP or on the tel )
Well...i tell if your tips work tomorrow =)
The point of this technique is to reduce the number of points it could fail, and remove the requirement for the previous ROM to work. The RUU for shipped ROMs can establish a connection without activesync.
Well ...
But i forget to say ...the s200 can't power on when it's plug on USB...it power only with the charger
With USB, no LED, no screen ....
Have you got a tips to connect the phone with charger+USB cable ?
I was following the instruction here on how to backup and re-flash your own Hermes ROM:
http://www.modaco.com/content-page/...ring-your-htc-hermes-rom/page/20/#entry894621
After I completed the last steps 9 of running RUUWrapper.exe, the screen told me that my ROM upgrade have completed successfully. then I looked at my Hermes and the screen is black and and it seems to be powered off.
After exited RUUWrapper.exe my PC Activesync icon is gray.
So I tried to soft reset and also hard reset, nothing happends.
I took battery out overnight and put back in and hit power and still won't turn on.
I plug USB cable in and the charge indicator amber light doesn't come on, if I have the battery out while USB cable plugged in, the charge LED will become red, but as soon as I put the battery back in the red LED goes away and doesn't turn amber color (the normal charging LED)
I've read both of the following:
"dead hermes? corrupted radio? Post comments here"
http://forum.xda-developers.com/showthread.php?t=369434
Common Upgrading Problems in HTC Hermes
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem6
any suggestions please??
Will doing the KITL+PB to try to boot OS will help? http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
But my Hermes won't even turn on now?
First thing I'd try (if you know someone with a hermes like yours) would be to swap batteries and see if theirs wont turn on with your battery and if your hermes will with his battery. Or you could go to a phone shop and see if they have a spare battery lying aroud to try (with the added promise of a potential sale if it works). Hope you can fix it though... Cheers...
Actually I just swap battery with my friend's working Hermes and his can turn on with my battery, and mine still won't turn on with his battery.
Seems there's very little I can do if my Hemes won't even turn on or response with USB cable plugged in.
Any other suggestion? I'm getting pretty desperate.
sounds like a hardware problem. if its under warranty, take back. If not, and you really wanna get fixed, you might have to pay. Check pricing first though as you may decide to upgrade instead.
i hav exactly the same problem. herme 300 t-mobile bootloader 1.11 (ipl 1.01) i never managed to flash it ether with sd card or from my pc (winxp). i recieved different errors: invalid vendor, not allowed... help plz
sorry form the poor english
paloma728, you need to sim/cid unlock your phone, HERE : http://forum.xda-developers.com/showthread.php?t=293665
THEN you need to Hard SPL your phone... HERE : http://forum.xda-developers.com/showthread.php?t=296722
But 1st you need to do some reading through those threads I just gave you. Also look for mrVanxs upgrading guide. You wouldn't have got in trouble if you had've first done some research....
Hope this helps you out of your mess... Cheers..
ultramag69. with all respect, how can i cid or sim unlock it. my herm stk in bootloader 3color screen. sometimes turns on but the screen remains black (displays nothing) by the way this was the result of wrong flashing (idont know how bkz i gave i to a friend to do the job 4 me!! . may u help me out of this. actually i did alot of reading but couldnt find any solution to my device.
thx 4 ur concrn
1st thing I'd try to do is to Hard SPL the phone. That was on page 116 of the "Hard SPL or how not to brick your hermes" thread I directed you to. It shows how to do using sd card. Then try to reflash with stock rom. This should get you back to where you started. Use the sd card method as I don't think you'll be able to use the pc. I don't know if this will work as it sounds like your friend also didn't Hard SPL your phone.
You REALLY shouldn't let anyone play around with such an expensive toy without proof that they know what they are doing (for example, own one themselves and have flashed their own MULTIPLE times with no problems) ... You might have a very expensive paperweight, and a bit more wisdom about letting others do what you should have learnt to do yourself.
All the best and I hope you get it working... Cheers...
i tried the solution u gave but didnt work too. the solution works with unbricked devices i gues (able to copy and excute files from it) but for me i tried to boot only the"HERMIMG.nbh" from the sd card (4 color screen or just black screen) & wich shows the following error code:00068002
thx for ur help.
paloma728, try flashing a stock rom. yu can do this by the sd card method too. I REALLY don't know if this will work but at this point it can't hurt. Nothing to loose and everything to gain... As it is the "right" update it MAY pass the CID check. Hope all goes well... Cheers..
your battery topped off while being plugged is my best guess. i dont think it's with the flashing of the rom at all
im new to this stf. (stock room)?. is it the exacly the method of copying the "RUU_signed.nbh" file to sd card and rename it to "HERMIMG.nbh" ?
if this is what u meant by stk rm then im not lucky again. i tried it b4 with many different rooms & always get errors
plz may u explain? thx for ur help & concern
today i downloaded an original room from t-mobile NL then tried the sd method & i recieved a new error code:"00028002 not allowed".
what does it mean plz?
You may have to take back to your supplier and see if they can fix under warranty if that didn't work. Don't hold your breath though...
unfortunatly there's no splr in here (morocco). thx alot mate
try this http://forum.xda-developers.com/showthread.php?t=369434&page=39
maybe u can revive the herm