sorry if this shouldnt be here, but i really cant figure this out. Im using a united states HD2 with 1024, i have it connected via usb with active sync then i run HSPL2 and then it restarts to the bootloader, and it allows me select the HSPL 2.08 and then i run it and it just sits there and nothing happens. =( any help?
for reference, tmous section is here
in answer to your query, use HSPL3 (see my sig for link)
manually enter bootloader yourself (power off, press and hold vol down, tap and release power) wait for 'serial' to become 'usb', then right click hspl.exe and 'run as administrator'
also, im only using windows XP, so how exactly to i run as administrate? i dont use windows very often
sorry, dunno, been a few years since i last used xp.
Related
When I perform a ungrade to my XDA II. the update program tells me that there in an error. On the same time the PPC can't start reset and totally no response. Any expert can help? Many many thanks.
Push power button while pushing reset, then restart the flashing process.
Upgrade
Thanks for your nice reply. But I have already try it. Any other things I can do?
After a while. I can see a text on screen
On top it say "Serial"
At down side it say "V1.03"
If you now plug it in it should say usb and flashing should work.
I have try XdA2JoJo.v3.2zS.exe and the original row upgrade software from O2. It both day the device cannot be connected. I am using a sync cable, and cradle without power cord.
Is it a must to have power cord plugged in to the cradle before doing ROM flash.
I am also got the following findings.
1. Windows cannot detect my XDAII device.
2. I cannot enter bootloader using procedure in this site.
Upgrade Done.
Finally the upgrade done and I can consolidate the following experience.
1. When fail within upgrade process. Remember to hard reset.
2. I think Windows needed to detect the device with driver something like "Microsoft Sync Device", for a successful upgrade when my device show up "USB" and "v1.03".
Well I was trying to upgrade mt niki to 6.1 but apparently I must have missed a step or did something I shouldt have and now I am stuck with the color bar screen. Can anything be done? I am running Vista.
tri-colour = Bootloader
The tri colour screen is the boot loader screen, when you updated, did the progress bar go allll the way to 100%?
If so, its in bootloader, try to flash another rom from you computer,
Also run through what you done to update - What rom also. Did you hard-spl, Uspl or anything like that?
It stopped at 15%. These are the directions I was following:
Originally Posted by Judge584
Follow these steps:
1. download the attached files (flash-uspl-niki.zip & sspl-1.16-nike)
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the uspl by running ROMUpdateUtility.exe from flash-uspl-niki
9. Now you can flash the latest rom update to have spl 1.22 and wm6.1.
ouch, Thats the only problem with sspl,
urmm.
How long did it stay at 15%?
As the device isn't CID unlocked you can only flash official roms...
Find an official rom, in the bootloader connect the USB and see if it will flash. It should do!
fingers crossed..
the only rom I can find for singtel in singapore is an updated one so I am trying that now so far so good, I am at 30%. So if this will get me going again can you offer a little advice or explination as to your last post, how do I go about loading a newer 6.1 rom on my device?
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Deejaynate said:
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Click to expand...
Click to collapse
well i was able to fix it by using the singtel rom. I want to use the Niki SuperCID unlocker but I have to install the " HardSPL 1.15 MFG " first - can you walk mw through this so I dont brick my touch again. do you have messenger?
yeah Windows live messenger, add me [email protected]
sorry to hijack your thread, but I encountered exactly the same thing. The screen is now stuck with 3 colour bands. I tried to flash it with an official rom, but the computer is not connecting with the phone, active sync does not recognise the device, any help!?
this is what I did:
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. running ROMUpdateUtility.exe from flash-uspl-niki
Sorry for the non prompt reply
I have been at work alot lately,
sorry for a non prompt reply.
Active sync wont connect to your phone, as its in bootloader mode.
At the tri-colour screen, does you computer beep when you connect it, or try to install drivers?
thanks for replying!
no beep from the computer, when connecting the usb to the phone, the phone changes from "serial" to "usb".
I tried reflashing with ROMUpdateUtility.exe from flash-uspl-niki, it will work, but says fail and will go into recovery mode. It will then complete the "recovery" action and go back to flashing new rom which won't work.......
The same ocurred with me!! Help me!
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
luismatos123 said:
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
Click to expand...
Click to collapse
You need to flash an original ROM from your service provider (phone company).
I am trying to flash from the bootloader to recover from an installation error on my Fuze. I've entered into the tricolor bootloader screen by holding down Vol.down and reset. Now, when I plug the phone into the computer, the computer recognize the phone as a Qaulcomm CDMA Technologies MSM, and is trying to install a driver for it (which it cannot find.) When I run the Custom_RUU, it does not find my Fuze and is showing a ERROR[260]: Connection.
What am I doing wrong? Do I need to find a driver for Qualcomm first? I searched, and it seemed that when you enter bootloader to flash, it is suppose to say USB at the bottom. Mine says Serial. Does that matter?
If more information is needed to troubleshoot:
SPL is SPL-1.90.OliNex
Phone is unlocked by using Olinex's unlocker
Rom was EnergyRom 3.0 Phoenix 51909
Problem was caused because I tried to install Studio Kuma Traditional Chinese Fonts on it. That program works flawlessly on a WM6.1. Of course, Energy 3.0 are WM6.5, hence causing the problem.
Any assistance is very appreciated.
Try sd card flashing
You have connect your device to your USB port and let it find the drivers. In order for it to download the drivers, you must have Activesync or Windows Mobile Device Center.
Once you have one of those downloaded, launch it and connect the device while it is running normally. Opt to connect via Activesync on your phone. You don't have to have these running in the future but you need it to find the drivers and install them. Leave the Activesync connection intact while you run the Flash program.
Once the phone reboots in bootloader mode, the PC will probably download some more drivers. The Flasher will probably time out while the drivers are being downloaded and installed. Keep trying.
Once the bootloader drivers are downloaded and installed, try to run the Flasher program again. Sometimes you'll need a reboot if something is hung up.
You SHOULD be able to reboot, put the phone in bootloader mode (Down + Power + Reset) and it should change "SERIAL" into "USB". Once it displays "USB" you are good to go. Load up the Flasher program and it should go all the way through without the assistance of ActiveSync or Mobile Device Center.
I always flash in bootloader mode, I just know the initial pairing is rough.
Well, I flashed from sd card, and the phone is working now. Thanks for everyone's replies.
Hi,
My new Gene is bricked. I am trying with the Orefkov SPL updater. I am getting the Boot loader screen but I am stuck with MTTY. I am not getting the USB button. Please help
WHAT IS YOUR OS? IS IT WINDOWS XP OR VISTA/7?
IF YOU ARE USING WINDOWS VISTA/7 YOU NEED TO HAVE WINDOWS XP ACTIVESYNC DRIVER INSTALLED.
Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Here is the link to the Master of all masters Sumit's official thread for more info:
http://forum.xda-developers.com/showthread.php?t=472169
HI Schizo,
Thanks for the quick reply.
I have Win XP and I have ActiveSync installed. I have removed SD Card, Sim and did the same way you have explained. But still I am getting only COM1 and COM2 in the dropdown in MTTY.
Please help.
Anything specific to be done with ActiveSync?
go to computer> right click and select properties and go to device manager. Is there anything called pocketpc usb sync? If there is pocketpc usbsync or unknown device then Update it with the driver i have attached below. and one more thing keep on refreshing the page from time to time.
No Schizo. I dont have anything like that.
I have Windows Mobile-based Device#7 in Network Adapters. Is that a problem?
rexhyd said:
No Schizo. I dont have anything like that.
I have Windows Mobile-based Device#7 in Network Adapters. Is that a problem?
Click to expand...
Click to collapse
then upgrade that with pocktpc usb sync driver i have attached above and try again. Let me know if that worked.
Link:
http://forum.xda-developers.com/attachment.php?attachmentid=270636&d=1264088925
Sorry to ask but how to update it?
rexhyd said:
Sorry to ask but how to update it?
Click to expand...
Click to collapse
Unzip the files i have send you.
Go to device manager, right click on windows mobile and select update driver.
select browse my computer for driver.
select let me pick from device drivers and choose have disk.
go to the folder you have extracted the drivers and select pocketpc usb sync.
I am using windows seven but i believe steps is basically the same
I have right clicked on WceRndis and wceusbsh and selected Install. Will that do?
rexhyd said:
Sorry to ask but how to update it?
Click to expand...
Click to collapse
unzip that and then right click on inf files it shows install
then re plug device
rexhyd said:
I have right clicked on WceRndis and wceusbsh and selected Install. Will that do?
Click to expand...
Click to collapse
Now replug the device and start all the steps as posted before. Let me know if that works
Hi,
I have done it. Now I have a white screen and I am going to run RomUpdateUtility.exe program.
Thanks a lot
I am done now My SPL is 1.07.Oref. Thanks a lot guys. I was damn scared that I've lost my Gene. But You guys made it. Thanks once again.
Can you suggest which ROM will be best for my mobile?Please
congratulations, now update to the ROM of your choice. Glad to help. Had the same problem, woke up till 5 am in the morning trying to fix that. For new ROMS just browse the section. Plenty of ROMs for our new gene here. Enjoy
@schizo440 Good job mate
Great to hear that one more Gene was saved. Good job schizo440
@rexhyd : From now on, never flash any ROM that says its for Old Gene, and also those which say Stock Rom or Official ROM etc. For the second type of roms, ask in the forum first, whether they are safe or not. Good luck!
I have the same problem too.
Hey, I have the same problem. Im stuck at the tricolour screen showing SPL 1.10. Olip. Mtty doesn't sho usb option. Im on Windows 7 please help.
msrkanurag said:
Hey, I have the same problem. Im stuck at the tricolour screen showing SPL 1.10. Olip. Mtty doesn't sho usb option. Im on Windows 7 please help.
Click to expand...
Click to collapse
kill active sync process at taskmanager
really nice work schizo440......
Hey guys, as the title suggests....im having trouble
Trying to update my ROM.
Active sync works fine, up to the point I have to run the RUU and .nbh files, it just drops out and then i get the error 266 coming up.....asking me to check the cable etc.
Tried different USB ports and leads with no joy.
Strange one this, as I have updated my ROM before (around a year ago) with no trouble.
Help very much appreciated.
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
AndrewSh said:
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
Click to expand...
Click to collapse
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first?
Im following these instructions:
FIRST TIME FLASH
1. Remove SD (and remove Application Data and Program Files folders from it using SD card reader)
2. Remove HSPL with HSPL2_RUN.exe (flash SPL 1.66.0000 with HSPL2_RUN.exe)
3. PowerOff the phone
4. Boot to bootloader (VolDown+PowerOn) and when it shows "USB" flash stock ROM by running matching RUU_Leo_S_HTC_XXX_3.14.XXX_Radio_15.42.50.11U_2.15 .50.14_LEO_S_Ship.exe (get yours HERE or for Orange UK/FR HERE)
5. Hard Reset (when phone starts booting after step 4, remove the battery, insert it back press VolUp+VolDown and still holding both press PowerOn and follow the instructions)
6. Boot to homescreen.
7. Run SSPL_RUU.exe with Artemis v4X RUU_Signed_XXXX.nbh in the same folder - YOU HAVE TO BE ON HOME SCREEN, NOT BOOTLOADER (this took me 3 tries until succeded - yes - nerve wrecking, but works). If it doesn't work (hangs on black screen for more than 2min or stays at 0%) remove the battery and try again. If still doesn't work - try solutions in NOTE below.
8. Hard reset (instructions in step 5)
9. when on homescreen - softreset.
10. Insert SD
marlon32 said:
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first
Click to expand...
Click to collapse
You're going about things in a strange manner, using hspl.exe to set a stock spl and then using sspl to flash the rom? Pretty non standard, what are you aiming for? My guess is you are using outdated instructions from before Hspl4 was released to handle spl/hspl 3.03 (just a guess, of course)
Stabdard flashing a 3.14 rom would go as follows,
Phone into bootloader(forget actuvesync)
Run Hspl4.exe, choose 3.03.hspl
Back into bootloader,
Run the Artemis flash using custom ruu .
Done.
It won't show the current installed image because that is a simple registry entry and is only accessible when winmo is running, but when winmo is running the USB times out when the ruu reboots into bootloader,sim that's why we manually enter bootloader.
(I haven't checked in the Artemis thread as to if there's a reason why his rom wouldn't follow standard proceedures, but I did use exactly your process prior to Hspl4 release)
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
marlon32 said:
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
Click to expand...
Click to collapse
Thanks M8 Had the same problem and moved my usb cable to another port worked 100%