i everybody!!
my x02t softbank rovider it only japanese language
i try flash it and now I power-up the device, It's only have a green LED flash and vibrate a single time.
After, I connect the Pin 1 & 3 and try with other rom but fail
every help me
can i flash it with origin rom? and i can get it where?
http://forum.xda-developers.com/showthread.php?t=682480
try that, good luck
I cant power-up the device by the normal way after i flashed it into English. I have to short pin 1 &2 at the same time with the power button to power-up that device.
i would like to power-up it by the normal way so that would you might to suggest any solution to solve my problem?
EVERY BODY HELP ME
tempb said:
EVERY BODY HELP ME
Click to expand...
Click to collapse
did you try TG Downloader?
Use the TG TOOL to convert TG rom to T01A rom,
http://forum.xda-developers.com/showthread.php?t=659589&highlight=t01a
and after that decrypt it:
1- make a folder on your desktop and rename it TG01
2- Put 2 files inside:
a- T01A rom
b- TGtool
3- press start--> Run--> type cmd in it
4- type:
a- cd desktop/TG01
b- tgtool -dec T01A_to_SP50_wm65.tsd tg01.bin
and then you'll have the tg01.bin file in that folder
Use this file with TG Downloader
If you don't know what to do or How to Do, just send it back for service, it's better to save your phone before it's completely dead..
wafeeq said:
did you try TG Downloader?
Use the TG TOOL to convert TG rom to T01A rom,
http://forum.xda-developers.com/showthread.php?t=659589&highlight=t01a
and after that decrypt it:
1- make a folder on your desktop and rename it TG01
2- Put 2 files inside:
a- T01A rom
b- TGtool
3- press start--> Run--> type cmd in it
4- type:
a- cd desktop/TG01
b- tgtool -dec T01A_to_SP50_wm65.tsd tg01.bin
and then you'll have the tg01.bin file in that folder
Use this file with TG Downloader
If you don't know what to do or How to Do, just send it back for service, it's better to save your phone before it's completely dead..
Click to expand...
Click to collapse
It was not possible for me to make a bin file as tried to make it several times but failed. Kindly someone make and host it to download.
Related
hi all, help me to back up my roms plzzzz
my ori rom is
Rom v 1.03 USA
n bootloader mode v 1.02
i wanna upgrade to wm2k3SE
but i cant back up my rom ?
if i wan to back up always pop up notice
Card initialize is failed ??
wat thats means ?
thzzz for ur anssss
While a lot has been written, the following should provide an easy-to-follow guide:
Preparation:
1. A torch (read on and you will know why)
2. 256M SD card
3. Download ntrw.exe, romupdate.exe, hexedfull.exe from the ftp of this forum to c:\ and install hex editor
4. Download the appropriate ROM file (hereafter referred to as "newrom.nb1"). Somehow, these rom files seemed to be deleted from this ftp. I will upload them later.
5. Cancel USB in ActiveSync
6. Use Sprite Backup to backup your ppc
Backup original ROM:
1. Put ppc into the boot loader mode (hold both on/off and camera buttons at the same time while resetting).
2. Insert empty SD card.
3. Connect ppc to pc through USB.
4. Run romupdate.exe on pc.
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
6. Don’t get panic to see the ppc screen goes dark. Use your torch and you will see the download percentage. Wait until it reaches 100% and shows “CheckSum is OK!”.
7. Insert SD card into card reader of the pc. Ignore the “format SD card” message and click “No”.
8. Run “command” to go into DOS prompt and change to root directory (cd c:\). Enter “ntrw read oldrom.nb1 s:” where s is the drive of your SD card.
9. Ignore the “Data error <cyclic redundancy check>” message. You should save another copy of this important rom file “oldrom.nb1”.
Change header of newrom.nb1:
1. Right click on oldrom.nb1 to open hex editor. Copy the first 220 bytes.
2. Open the downloaded newrom.nb1 file and overwrite the first 220 bytes with those of the old rom.
3. Save the edited newrom.nb1. You may save another copy of this important file.
4. Go to the command prompt and enter “ntrw write newrom.nb1 s:” to write it to the SD card. Ignore the error message “The parameter is incorrect”.
Update the ROM:
1. Insert SD card into ppc and put it to boot loader mode again (on/off + camera + reset). Use you torch to check the dark screen.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your ppc.
4. You may have to reinstall your software, unless you are familiar with the advanced features of Sprite Backup.
or u can find at http://forum.xda-developers.com/viewtopic.php?t=19500&highlight=rom+backup
thanks to talent and all XDA Dev
Phreakazoidz
1. Download the 20060426 from www.seeo2.com
2. Run DSUU, after extracting the files in directory windows\temp DO NOT CLICK NEXT
3. Copy all 6 files into temporary or another directory
4. From that 6 files, copy 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, rename diskimage_ver.nb0 into diskimg.nb0
6. Now, you can run bootloader by pressing camera and soft reset ( you have to put your mini SD into your Atom so that the bootloader will boot from mini SD
7. Just wait and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that your screen will blank, do not worry or panic
9. Pull out your mini SD and connect USB to PC and run bootloader again
( please make sure that your usb already connected to pc )
10. Now u can normally run the 20060426
This topic has been posted in many threads, there is no need to use the SD if this procedure is not done correctly you will loose the bootloader all together. Instead use the method posted by Luchao:
1.run atom 0416 rom update program, after the DSUU program extracted the files, don't click "next", go to windows/temp folder, copy those files extracted, except "diskimage_Ver.nb0" and "ExtendedRom.img", then save them somewhere else.
2.run july exec rom update program, after the DSUU program extract the files, don't click "next," go to windows/temp folder, overwrite with the files you just saved, this will leave only the diskimage_Ver.nb0 & ExtendedRom.img files as of the july exec rom, others become atom rom files, including an older bootloader which allows you to flash back other roms.
3. flash
http://forum.xda-developers.com/viewtopic.php?t=52925&postdays=0&postorder=asc&start=150
i just saw eboot.nbo & test.zip file in windows/temp/ folder, how to get the others file ? Thanks.
activesync mode not working
i tried the activesync mode, but not working.
finally i used bootloader method. just copied eboot.nb0 file to your miniSD. and enter bootloader mode.
Re: activesync mode not working
klikman said:
i tried the activesync mode, but not working.
finally i used bootloader method. just copied eboot.nb0 file to your miniSD. and enter bootloader mode.
Click to expand...
Click to collapse
bro, just klik next one more time, and DSUU will extract the others files
tjs0509, I tried your sd card method and totally lost the bootloader when I tried camera and soft reset. Is there anyway to bring back the bootloader?
interesting methods...
thanks!
"Camera" + SR, connect USB, run Device Software Update Utility, flash...
dear
tjs0509
I Downloaded the 20060426 from www.seeo2.com
2. Run DSUU, after extracted the files in directory windows\temp DO NOT CLICK NEXT
3. I Copied all 6 files into temporary or another directory
4. copied 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, renamed diskimage_ver.nb0 into diskimg.nb0
6. Now, I maked bootloader by pressing camera and soft reset ( I had to put my mini SD into your Atom so that the bootloader boot from mini SD
(from 1 to 100 dowloded)
7. I seem and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that My screen was blank,
9. I Pulled out my mini SD and connect USB my pc . After I waited since 2 hour .screen been Black.. black... Black..I tried soft reset .and batery out -in but not anythink .
I was worring .!!??
Can help me What can I do?
Homer285, any help. I really lost the bootloader in the SD card method. I tried to connect USB and the 0721 ATOM EXEC recognize the ATOM, but when downloading the ROM, the ATOM just rebooted. I cannot press camera and reset to go to bootloader mode. Is bootloader mode be activated by a program in SD card so that it can be run in the explorer. Please help.
tjs0509 said:
1. Download the 20060426 from www.seeo2.com
2. Run DSUU, after extracting the files in directory windows\temp DO NOT CLICK NEXT
3. Copy all 6 files into temporary or another directory
4. From that 6 files, copy 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, rename diskimage_ver.nb0 into diskimg.nb0
6. Now, you can run bootloader by pressing camera and soft reset ( you have to put your mini SD into your Atom so that the bootloader will boot from mini SD
7. Just wait and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that your screen will blank, do not worry or panic
9. Pull out your mini SD and connect USB to PC and run bootloader again
( please make sure that your usb already connected to pc )
10. Now u can normally run the 20060426
Click to expand...
Click to collapse
this method broke my bootloader too. i spent about RM200 to repair my bootloader...grrr
Small soft-pack for removing free space from Gene ROM, make lzx compressing ROM and set Extrom size to 2MB (extrom will be cleared).
After use it and flashing new ROM, you will have 65-70 MB of user storage.
Use it on own risk.
Usage:
1. Unzip this archive to one folder (for example c:\lzx).
2. Put file ruu_signed.nbh from your ROM in this folder too.
3. Run make_lzx.cmd
After it work about 5 min, and you will have new ROM as file GENEIMG.nbh in this folder.
Flashing:
This ROM cant be flashing throught RUU.
You must flash it from SD-Card.
On your device must be HARD-SPL installed !!!
Format SD-Card as FAT32.
Put GENEIMG.nbh on SD-CARD.
Charge your device at 100%!
Insert SD-Card in Gene, press AND HOLD "Camera" button, and do soft-reset.
If you see white screen with "Reading SD content":
Release "Camera" button, wait, and when countdown in left-bottom corner of screen is appear, press "Power" button. Flashing is begin, and approx. 5 min long. After you will see "Success. Press any key". Do soft-reset. Congratulation.
But if you see 3-color screen, then you mast do magic with your SD-Card.
See http://forum.xda-developers.com/showthread.php?t=371147
Good luck!
Cant upload file to this forum.
Download from http://www.filefactory.com/file/8f6656/
thanks orefkov .. will give it a shot tonite.
hmmmm will try it tonight
orefkov i am getting this error bro .........
NJackal said:
orefkov i am getting this error bro .........
Click to expand...
Click to collapse
try unpack archive closer to root folder, ie c:\lzx
Or try it on WinXP.
need help
i have successfully flash the rom with this tool, after that i soft reset, device automatically boot into windows mobile 6.1, runs all the basic setup (screen align, date setup), then it automatically load some setup, after setup, device automatically reset..... PROBLEM start here, it stop at the first screen, refuse to boot into windows... i hard reset, soft reset, still the same, anything wrong?
try press power button some times, or reinsert the battery.
NJackal said:
orefkov i am getting this error bro .........
Click to expand...
Click to collapse
hmmmm no change getting the same error again ............. and i am using xp only bro it is a vista theme only ..........
NJackal said:
orefkov i am getting this error bro .........
Click to expand...
Click to collapse
Have you tried appending the temp folder's path in CMD? The process cannot find the file - so appending the path might help. Also, the batch file doesn't seem to recognise long filenames. That could be the reason the files inside your desktop can't be found.
I create GENEIMG.nbh from a wm6.1's nbh file by your tool and flash it successfully. But it stop at the first screen, refuse to boot into windows... i hard reset, soft reset, still the same, anything wrong? Thanks a lot!
That work unstable on 6.1
Try on 6.0
Or try with that xip.
orefkov said:
That work unstable on 6.1
Try on 6.0
Or try with that xip.
Click to expand...
Click to collapse
Thanks a lot! I'll try that again by your new Xip and report the result.
Hello, orefkov:
I try your new xip, but it has the same problem.
I'm using is not a official rom but a chinese version with core 19199. What I can do? Thanks!
then you mast do magic with your SD-Card.
what is the magic??
I dint get u..
Every ROM cant be flashed from SD card.You must make it to boot from SD card.Also make sure that you have formatted SD card in FAT32 and proper chunk size.
OK, let's start:
1. Download https://www.dropbox.com/s/rnqrx7xh4z27zfr/KDZ.RAR
2. Unpack archive and open folder KDZ
3. Drag the firmware file (eg, V10J_00.kdz) on 1.unpack_kdz.bat
4. You get ,cab file (eg. V10J_00.cab)
5. Drag the .cab file on 2.unpack_cab.bat
6. In stock folder, you can find firmware folder with .dz, and .dll file
7, Download https://www.dropbox.com/s/sjb9ff7wmpdxl6a/LGwinTools_1.02.zip
8. Unpack archive LGwinTools, start LGwintools.exe
9. Open our .dz file previously extracted in stock folder
10. Click on 'save' icon (dont work through File ... menu), and choose folder for extraction...
That's it.
To unpack system.img:
1. Download https://www.dropbox.com/s/z7mqlzmobblf0d7/ext4_unpacker_exe.zip, and unpack it.
2. Run the ext4unpacker.exe, choose image file (system), and click on save as ext4. You can't miss, only 3 buttons is available: open image file, save as ext4, and exit.
4. Name it however you want .ext4 and save.
5. Download https://www.dropbox.com/s/5i33dt4n0w2z398/ext2explore-2.2.71%20%281%29.zip, unpack it and run ext2explore.exe,
6. Choose system.ext4, and do whatever you want.
Enjoy
I understand all points what you write...But then, the last point absolutely not understand.
Choose system.ext4, and do whatever you want?????
Please help me, thank you and sorry for my English.
So basically, it turns the kdz into a zip file that can be extracted?
So i just copy the file on the SDcard and install zip from the SDcard in recovery?
EDIT: Now the phone doesnt turn on..when i turn od it will displayed blue strips and thats all..
Pecan6 said:
I understand all points what you write...But then, the last point absolutely not understand.
Choose system.ext4, and do whatever you want?????
Please help me, thank you and sorry for my English.
Click to expand...
Click to collapse
Read carefuly point 4.:
To unpack system.img:
1. Download https://www.dropbox.com/s/z7mqlzmobb...packer_exe.zip, and unpack it.
2. Run the ext4unpacker.exe, choose image file (system), and click on save as ext4. You can't miss, only 3 buttons is available: open image file, save as ext4, and exit.
4. Name it however you want .ext4 and save.-MEANS ADD (.ext4) extension (eg. system.ext4)
5. Download https://www.dropbox.com/s/5i33dt4n0w... (1).zip, unpack it and run ext2explore.exe,
6. Choose system.ext4, and do whatever you want.
Dennydap said:
So basically, it turns the kdz into a zip file that can be extracted?
Click to expand...
Click to collapse
No, it turns kdz file in readable format, with possibility to manipulate with files.
When someone figure out how to pack changed/switched/modded files back in kdz, we will have tool to distribute rom through KDZ-s.
Pecan6 said:
So i just copy the file on the SDcard and install zip from the SDcard in recovery?
EDIT: Now the phone doesnt turn on..when i turn od it will displayed blue strips and thats all..
Click to expand...
Click to collapse
Why did you do that?
This is tool for extract rom files from kdz pack to regular format.
Where did you find a word zip, or zip for flashing in thread?
Flash only regulary kdz for your phone model, or verified rom.zip...
Read this; http://forum.xda-developers.com/showthread.php?t=2409308
Rename Topic
Rename the topic to "LG IL3 II, L5 II, L7 II, L9 II. How to Correctly unpack KDZ"
can u help me
there is a way to convert lg p705 kdz to be a ToT file.
i need that origial tot for unbrick this l7. thanks.
rezzkull said:
there is a way to convert lg p705 kdz to be a ToT file.
i need that origial tot for unbrick this l7. thanks.
Click to expand...
Click to collapse
Idk if it is even possible for P705 (never hear anybody did it, or have it).
I know how to extract partitions from dz (and merge system), but what is the difference, or how did you recover P705 with tot file, and why did you didn't with dz?
Anyway, I think you can find more information on lg l7 forum...
hs usb mode
the phone is hardbricked
the jtag pinouts now was damage (sorry cant upload picture)
if the only way can fix dead boot via usb mode, it will be superb things.
the emmc modem n etc does not detected in device manager.
any advice????
Is it possible to get boot.img and recovery.img?
rezzkull said:
the phone is hardbricked
the jtag pinouts now was damage (sorry cant upload picture)
if the only way can fix dead boot via usb mode, it will be superb things.
the emmc modem n etc does not detected in device manager.
any advice????
Click to expand...
Click to collapse
Have you any sign of phone in device manager? Try to pull out battery.
If not, i doubt even qpst (with proper emmcbld.hex) help you.
How did you damage jtag pinouts? If you try to recover boot area, with which device?
maxx_hr said:
Have you any sign of phone in device manager? Try to pull out battery.
If not, i doubt even qpst (with proper emmcbld.hex) help you.
How did you damage jtag pinouts? If you try to recover boot area, with which device?
Click to expand...
Click to collapse
sorry for late reply...
the phone is usb qualcomm 9008 mode at device mnager. with or without battery.
jtag pin damage is ... TDO , NRST n RTCK. all jtag pinouts are direct to Processor qualcom msm7227A. and that ic is permanently glue.
it impossible to reball n re write if the IC was damage by hot air .
thanks for advice.
if any other way from usb to repair dead boot mode....please tell me?
thank you.
Br.
rezzkull said:
sorry for late reply...
the phone is usb qualcomm 9008 mode at device mnager. with or without battery.
jtag pin damage is ... TDO , NRST n RTCK. all jtag pinouts are direct to Processor qualcom msm7227A. and that ic is permanently glue.
it impossible to reball n re write if the IC was damage by hot air .
thanks for advice.
if any other way from usb to repair dead boot mode....please tell me?
thank you.
Br.
Click to expand...
Click to collapse
You won't get away with that without a very good RE knowledge and the time will not be worth most likely. You can destroy any connection with QDL Mode with wrong files. I have been there. Sorry, that phone is done.
my stupid question
how to repack kdz?
THANK YOU
THANK YOU SUPER EXPLAINED ... SENT FINE.
:laugh: :victory:
My phone is completely dead (no files) after flashing with a third party tool (chimera tool),
Now I can get .img files from the update.app and can flash with QPST, QFIL Tool, but the phone is not turning on (only showing bootlogo),
I think, I need to flash oeminfo.img file also, to fix the problem, which is not present in the update.app file.
So please anyone kindly share the oeminfo.img file of KIW-L22 to save my phone, my phone is dead since about last two months.
To get oeminfo.img file,
1. Run Terminal (or adb command) and enter superuser mode by typing 'su' and pressing enter,
2. then type,
Code:
dd if=/dev/block/platform/hi_mci.0/by-name/oeminfo of=/sdcard/oeminfo.img
if it doesn't work, then type,
Code:
dd if=/dev/block/platform/soc.0/7824900.sdhci/by-name/oeminfo of=/sdcard/oeminfo.img
and press enter.
3. oeminfo.img file is saved in your phone storage and please send me the file to save my device.
Brothers,
Your help can save my phone from dying,
I'm in a problem, please help me.