hello,
i have a problem with my TG01... i did a hard reset on it and when it went back on...after the TOSHIBA logo in the begining just when it shows the Orange logo...it gets stuck...i tried to unbrick it using this method: http://forum.xda-developers.com/showthread.php?t=682480
but when i try to power the phone...it just gets stuck to the orange logo and my W7 won`t see any drivers or devices...pls need help
Follow these steps:
YOU SHOULD HAVE THE TG DOWNLOADER INSTALLED ON YOUR PC
1- You need to take out the Sim card and memory card
2- locate the pins under the sim card, there's a small black plastic cover, take it off
3- put the battery back and connect ur phone to the pc
4- short circuit pins 1+3 while pressing power button
5- the PC will ask for drivers press automatic
6- start downloading software as per the thread
Hope this revives your phone
Take out the micro sd card and try then.If not after taking out the card give a hard reset.
Related
I have full flash HP6828, but still stop step 5,(Radio)
I have disconnect USB cable from PC, after 6828 still black screen, can not power on, and tried more method, but fail...
I have reference following manual, but I don't know JTAG point on my 6828,
who can help me?? will big thanks!!!!!
I've had a hung flash yesterday and here's how I resolved mine. Try it and see if it works for you.
1. Unplug from PC
2. restart PC
3. Take out phone battery
4. Wait for about 1-2 mins
5. Press and hold the two - buttons, and insert the battery (keep holding on to the buttons).
6. After 2-3 secs of placing back the battery, release the buttons.
7. At this time, if the phone dun boot, go to boat loader mode by press & hold the two - buttons again and poke the soft reset hole with the stylus
8. It should load to boat loader (white screen).
9. Connect to PC and run the HP rom v1.01.
knave said:
I've had a hung flash yesterday and here's how I resolved mine. Try it and see if it works for you.
1. Unplug from PC
2. restart PC
3. Take out phone battery
4. Wait for about 1-2 mins
5. Press and hold the two - buttons, and insert the battery (keep holding on to the buttons).
6. After 2-3 secs of placing back the battery, release the buttons.
7. At this time, if the phone dun boot, go to boat loader mode by press & hold the two - buttons again and poke the soft reset hole with the stylus
8. It should load to boat loader (white screen).
9. Connect to PC and run the HP rom v1.01.
Click to expand...
Click to collapse
Thank you very much, Now I have use JTAG method to fix, and if I were successful, I will post method share with everybody.
My 6828 is death
tangjunhu said:
Thank you very much, Now I have use JTAG method to fix, and if I were successful, I will post method share with everybody.
Click to expand...
Click to collapse
Could you please share you method. My HP6828 is dead too. There is still black screen and little vibrate (sound like operating fan) when press 2 "-" and reset.
I can't....
my device is HP Ipaq rw6828.... i have this problems twice, but ican solve it, now i had a same problem.... now i can't resolve it....
now my device still (dead) only LED indicator when i charge it...... i use anything method, but it's not work.... except JTAG, cz i can't use this method.... please, any other way except JTAG mode????????? many big thanks.................. if u have an opinion, email me, [email protected]
MY HP6815 IS DIED.
I was flashing with the good wm5 rom of NHOCBANME when the phone fell to the ground and has detached the battery!!!
My hp 6815 is off and doesn't turn on.
I tried to flash by ordinary mode but the phone is always off.
Only battery led is on if the phone is charging.
I think it is permanently damaged.
Can someone help me?
Test:
1 - Remove the batery...wait some secounds
2 - Put the batery back on it
3 - Press POWER
4 - Press RESET with stylus and press the 2 softkeys (the keys that are on top of the red and green buttons)
5 - The phone will enter flash mode
6 - Use software to re-flash or use SD card to do it(SD card option: card must be inside when you do this!)
The same thing happened to me... but i lifted the cell and there was no cover in the battery...
hope this helps...
Dead boot ?
Hello,
I have a same problem after flashing. No life in my 6815.
The LED used to blink orange when charging or usb connected but now it flashes orange-green. Does anyone know how i need to fix my boot with jtag or other fix?
Many thanks
A free TUROK game[Newest turok game out last year] for whoever helps me fix my bootup. Game is boxed, manual etc.
Thanks to GraeFNZ (and helloworld1)...This is the correct procedure:
" How to recover from semi-brick state:
1. Prepare a sd card with proper diskimg.nb0.
2. Pull out the batter for a few minutes.
3. Press and hold two "-" button and at the same time, put the battery in.
4. Wait a few second and release the button, then after a while, the device will be in bootloader mode. "
I have the same problem with 6815
Hello, I'm new to this forum I have problem with 6815, it's completly dead after trying to put wm 6.5 on it. I have tried to pull out battery, to put it back, to press "-" keys, to reset... but no succes. It's dead. Battery is fully charged. It's showing charging status when I conect it to the charger or USB PC port. Anyone, please help, doing it for a 2 days, my head and stomach are ruin...
Basically it get to the windows logo screen and stays. i dunno what to do
i tried to turn it off and on so many times and its not working.
my contacts are backed up but i dont want to install everything again. is there a way to fix it ??
i removed the sim and the sd card and for some reason its working. i put the sim card back without sd and the phone doesnt start up. iam clocking the phone at 998hz all the time using leocpuspeed
thanks
Try holding both volume buttons when turning the phone on and following the instructions to do a hard reset, only thing I can think of, if you've got your contacts backed up through MyPhone or on your pc can easily be replaced back onto the phone
thx i did that . i really appreciate the fact u bothered to reply unlike the rest
I believe holding the volume down just after the power on will put you in the tri-color bootloader screen. From there you could task29 start fresh and flash a new rom.
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
lisah456 said:
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
Click to expand...
Click to collapse
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
after task29,when your device reboot
press botton "volume down" and will go in bootloader mode
now if you have your device stuck in white screen,remove battery cover
press red botton for softrest and press "Volume down" botton
bobsbbq said:
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
Click to expand...
Click to collapse
opsss..sorry bob
i have look now your post
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
kikimax said:
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
Click to expand...
Click to collapse
It won't because you're in the bootloader. Does it say USB at the bottom of the bootloader screen? As long as it says USB when the phone is plugged into your computer, flash a ROM and be happy
Hello!
And what if my hd2 not entering into the boot loader?
Thanx in advance
There is only one way to get into the bootloader.
Hold down volume and keep it down....
After that press the start button and your phone will boot up.
Now you will see the tree colored screen and you're in the bootloader.
Goodluck.
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
When you are in the bootloader screen, connect the phone to the computer /with the usb cable/ on the same bootloader screen it will change to USB - look at the bottom of the screen:
Open the folder - on your computer - where the ROM you want to flash is:
find the "RomUpdate*.exe" or "Install.exe" /if Android it will most likely say "DAF.exe" - run it as Administrator/ file and run it. Do as it says on the screen.
Do not disconnect the cable, do not touch the device. When it is finnished it will restart the device, disconnect the cable and enjoy your new OS.
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
use a <4gb or preferably <2gb sd card - class 4 or 2 with LEOIMG.nbh.
HSPL3_pkg after that - make sure .nbh (as above on sd root) is your stock and you CLEAN-reinstall bootloader.
ps:
Then hspl, then radio, then magldr, then windows 7, the hacks, then call M$= LIVE!
Hi guys i have a similar problem. After task 29 i went into the bootloader but can't install any rom whatsoever. I have SPL 3.03 on my devide, mind no not hard spl but SPL. Can anyone please help me solve this issue? I also tried to flash using sd card but it doesn't work. Please help me save my hd2. Thanks in advance.
tmo-hd2 wont go into bootloader after task29
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india..
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
gdsbalaji said:
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
Click to expand...
Click to collapse
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
lms1407 said:
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
Click to expand...
Click to collapse
I hvnt even instaled MGALDR yet....task29 and hd2 went into trouble...need to get to bootloader to save it now
Tried this as well before posting....hv a 2gb sd card>formatted to fat 32> stock rrunbh to leoimg.nbh > moved to root of sd card....but this can only work if bootloader can be initiated right? i cant get to boot loader
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
SOLVED {bootloader dont load}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
DeAdMaNwa said:
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
Click to expand...
Click to collapse
Man, did you say blackstone? You should go into Blackstone forum
To go into bootloader, turn off the phone. Press volume down button and the POWER ON button (not start button) at the same time until the screen appear. It works on both Leo and Black Stone
Goodluck
I've been having weird problems recently with my SD card (or interface) and in the process of re-partitioning/formatting the SD card the phone went dead. I did the following as suggested in another thread, but nothing happens.
1) Remove MicroSD
2) Remove SIM
3) Remove battery and wait a few minutes; also press the power button while phone is off
4) Only re-inserting the battery, hold vol-down and then hold power until screen comes on (then release power but keep holding vol-down)
When hooking up to my Windows PC to attempt fastboot, I do get the windows notifications that it's trying to load USB drivers, but it fails. fastboot was working on this PC yesterday with same setup. Anything left to try? I appreciate any advice.
Thanks,
Drew
so it's done?!
drewzer said:
I've been having weird problems recently with my SD card (or interface) and in the process of re-partitioning/formatting the SD card the phone went dead. I did the following as suggested in another thread, but nothing happens.
1) Remove MicroSD
2) Remove SIM
3) Remove battery and wait a few minutes; also press the power button while phone is off
4) Only re-inserting the battery, hold vol-down and then hold power until screen comes on (then release power but keep holding vol-down)
When hooking up to my Windows PC to attempt fastboot, I do get the windows notifications that it's trying to load USB drivers, but it fails. fastboot was working on this PC yesterday with same setup. Anything left to try? I appreciate any advice.
Thanks,
Drew
Click to expand...
Click to collapse
First make sure the USB cable is not broken by trying it on a different device. If it works, plug the phone into an AC outlet and hold the power button down for 30 seconds. If that doesn't work, try the same thing on a car charger if you have one (this probably isn't any different, but I just read it somewhere). If it still isn't charging after trying this, I'd say its bricked. That is, unless you can find some miracle hardware trick to resurrect it somewhere. Good luck!
didn't work, but thanks for this tip. anything is worth trying at this point!