Related
I have upgraded and downgraded many times, never with a failure. I just upgraded to PDAVIET 4.0003. Went without a hitch but now my phone will not stay on the network, also it will every few minutes complain that there is no sim card. Card is fine as tested in my other phones. The interesting part is it functions fine on any 2.2 ROM.
Tried Smart1's True's and all PDAVIET, no WM6 allows the phone to work.
Cold resets don't resolve the issue. Is there something that could have gotten corrupted that is part of the phone OS and not in the ROM's?
I am at a loss to troubleshoot this issue.
Thanks for reading, any advice/suggestions is appreciated.
ron1n, what is the network protocol for your provider?
Do you use pap or chap, the setting choice in CommManager?
Is network set for auto in phone dialog?
In your connection settings, do you use Server assigned ip address or auto?
Since i have upgraded to PDAviet i have almost the same problem.
After soft-resetting my device no gsm connection is found.
The only solution is to go into phone option and start the manual search.
If it's connected it works without any problems.
Strange thing....I also tested a few gsm roms but always the same experience.
R0N1N said:
I have upgraded and downgraded many times, never with a failure. I just upgraded to PDAVIET 4.0003. Went without a hitch but now my phone will not stay on the network, also it will every few minutes complain that there is no sim card. Card is fine as tested in my other phones. The interesting part is it functions fine on any 2.2 ROM.
Tried Smart1's True's and all PDAVIET, no WM6 allows the phone to work.
Cold resets don't resolve the issue. Is there something that could have gotten corrupted that is part of the phone OS and not in the ROM's?
I am at a loss to troubleshoot this issue.
Thanks for reading, any advice/suggestions is appreciated.
Click to expand...
Click to collapse
Reflash Radio ROM (2.47.21 or 2.69.21 will work)
To reply to all of your suggestions. I have tried 5 different radio roms, none will see the phone network (GSM not GPRS) for more than a few seconds with a weak signal, then they fail and either go to flight mode or say that the SIM is missing. To reiterate, this was working fine up until yesterday with a few different WM6 ROM's. Coincidentally, the rear speaker failed at the same time. I resolved that issue, but the lack of phone service persists, although all AKU 2.2 ROM's work fine. Very curious....
DeviLduck said:
ron1n, what is the network protocol for your provider?
Do you use pap or chap, the setting choice in CommManager?
Is network set for auto in phone dialog?
In your connection settings, do you use Server assigned ip address or auto?
Click to expand...
Click to collapse
It is CHAP, although I am referring to the phone service not wireless GPRS. My network is configured for auto, although if I switch to manual (due to the lack of consistent conntection), it will not be able to see any networks, except briefly and intermittently.
Cheers
WM6 Sim Card issues [solution, use radio rom 2.19.21]
I've been using WM6 for awhile now, I've tried SMART1.3, PDAVIET 4.0.0.01, 4.0.0.0.3,4.0.0.0.3a and finally 4.0.0.0.4 .. but yesterday i tried to flash back to SMART1.3. After downgrading and upgrading, i got unknown sim status ! since yesterday , I've change my Radio Rom and OS ( I've tried almost everything ) but i can't get my phone to work in WM6 !! when i flash back to wm5 ( any AKU 2.2 version ) i have no problem with phone or GSM but as soon as I upgrade to WM6, I got unkown Sim status ... anybody , have any Ideas ?!!
Same Problem !
I have exactly the same problem !! it's not from radio ROM or OS !! I've tried 3 different version of radio ROM, and almost every single WM6 OS that is out there ! my phone stop responding yesterday after i changed my OS from PDAVIET 4.0.0.0.4 to SMART1.3 ! since then I've tried everything, but I can't get the phone to work in any WM6 OS! although WM5 (any version of it) is okay !
hma4 said:
I've been using WM6 for awhile now, I've tried SMART1.3, PDAVIET 4.0.0.01, 4.0.0.0.3,4.0.0.0.3a and finally 4.0.0.0.4 .. but yesterday i tried to flash back to SMART1.3. After downgrading and upgrading, i got unknown sim status ! since yesterday , I've change my Radio Rom and OS ( I've tried almost everything ) but i can't get my phone to work in WM6 !! when i flash back to wm5 ( any version) i have no problem with phone or GSM but as soon as I upgrade to WM6, I got unkown Sim status ... anybody , have any Ideas ?!!
Click to expand...
Click to collapse
Did it used to work?
Yes , it used to work ! I've been using WM6 for more than 2 weeks with no problem! recently I upgrade my os to PDAVIET 4.0.0.0.4, but I decide to change the OS back to SMART 1.3, after I changed it back, i got the error "Unknown SIM card , without the pin you can call emergency calls only" I tried my pin and PUK , but none works ! So i changed the OS to WM5 again. I've tried couple of different version of WM5 (JESTER, NVID) and I've found the phone works perfectly in wm5 !! as I said before I tried re-flashing my Radio ROM, but it didn't help !! i still can't get my phone to work in WM6 ! any of Pocket PC gurus, have any suggestion ?
S200 Gone Wacko with WM6 and I don't know why
Hello people
Okay so here is the situation, since about last week I have been using PDAViet 4.0.0.3 on my Qtek S200
Now I love this ROM..so much so that I spoon with it at night...um...crap lol Its fast and lite...but something went terribly terribly wrong yesterday
So around 1pm I disconnect my phone from my computer, and notice a "X" in the data connection arrows...okay I thought nothing of it. I go to a restaurant, get a phone call from my brother, and talk, and everything is fine. From there it went bonkers...it kept on trying to connect a GSM signal, and then would go out to no service...it would keep on trying and trying, and bogging down my phone....
So finally i got it stablize (with an EDGE data signal i thought) and of course a voice signal and went on my merry 2 hour drive back home to Montreal.
When I got to Montreal and was waiting in the dead moving traffic jam, I wanted to check the Windies cricket score on BBC, so I take out my phone and try to make a data connection. But again the X showed...i rebooted my phone and signal about 10 or 20 times, and finally got something...however by the time that happend I had arrived at home so i went and used my computer.
The GSM signal stayed, but I dont know if I had a data connection. I then went to a funeral, turned off my radio entirely, and then when I turn it back on...ooooooooo no signal...it would get 2 bars, and then drop, and then 2 bars "E" symbol, and then drop.
So from then on, i went nuts, opened up the back, took out the battery, checked the sim, installed another sim to make sure..and by now it went even worse..first INVALID SIM...then it went to MISSING SIM...urge to kill rising!
I finally said F it, and hard resetted my phone...but i noticed something upon the screen calibration..."NOTIFICATION ERROR...cannot find calnot.exe". After hard resetting and such, the problem still showed...
This morning, after leaving it overnight, it was still misbehaving...so I went to took it back down to the floating NVID file found here on XDA developers...and oddly enough...no more calnot.exe error...the radio signal is strong, and i get a data connection...So i tried to then upgrade to the new PDAViet 4.0.0.4s ROM, but again...calnot.exe error...so finally i am stuck at the NVID ROM...oy!
So I searched here on XDA Developers and on google...now while people have said they get the calnot.exe error, they also get this reglog.dll (or something to that effect) error as well...me on the other hand am only getting that calnot.exe error, which would seem to be the root of my problem.
What can I do fix this, and get back to the speedy 4.0.0.3 ROM (man I love that ROM)
Phone info:
ipl: 2.09
spl: 2.20.0000 (so I guess that my Qtek S200 is a G3 model)
radio: 02.47.21 (i even moved up to 02.69.21)
os: 2.20.7.34
so i really appreciate the help guys...take care...
*howls like a wolf*....nothing?
hofo_mofo said:
*howls like a wolf*....nothing?
Click to expand...
Click to collapse
Flash again the WM5 NoVid Rom,hard reset and if you come up with the same error,hard reset again... Tell me what happens... If it works flash PDAViet 4.0.0.0.3a...
Holy S*** I have the same Problem for like two weeks!!
Man , I have exactly the same problem !!! exactly !! i had PDaviet 4.0.0.0.4 and one day I got the same thing, No signal , then after i hard reset, the Calnot error ! then Hard reset again, and this time I got the replog error !
I get "Unknown Sim Card!" or "Unknow Sim Card status enter your pin" whenever I install WM6! My phone works perfectly in Wm5 though !!
I flashed radio rom in WM6, I also tried different sim Cards , but none works !I can not get the phone to work in wm6!
By the way, NVID is not a good rom to stay with.
tonydeli7 said:
Flash again the WM5 NoVid Rom,hard reset and if you come up with the same error,hard reset again... Tell me what happens... If it works flash PDAViet 4.0.0.0.3a...
Click to expand...
Click to collapse
Still the same thing...i have treid 4.0.0.0.3a, 4.0.0.0.3, 4.0.0.0.4, 4.0.0.0.4s, 4.0.0.0.4sse, and Mobiz 2.0b3.....all nothing...
Sometimes it would be calnot.exe notification error, or replog.dll, or now clocknot.exe error...so far only NVID works
hma4 said:
Man , I have exactly the same problem !!! exactly !! i had PDaviet 4.0.0.0.4 and one day I got the same thing, No signal , then after i hard reset, the Calnot error ! then Hard reset again, and this time I got the replog error !
I get "Unknown Sim Card!" or "Unknow Sim Card status enter your pin" whenever I install WM6! My phone works perfectly in Wm5 though !!
I flashed radio rom in WM6, I also tried different sim Cards , but none works !I can not get the phone to work in wm6!
By the way, NVID is not a good rom to stay with.
Click to expand...
Click to collapse
In a way I am glad you are having the same problem...so I know I am not a nut lol (and nor am I alone)...but of course its not good to relish in someones downfall, so of course it is also a bad thing eh..
What ROM would you suggest then? NVID seems alright, but I don't know of any others out there (well somewhat)...thanks!
I wish we knew why it happened at first place!
for wm5, if you want a clean, fast and reliable Rom, try Jesterz Rom
http://forum.xda-developers.com/showthread.php?t=284578
you might want to re flash the start-up image to HTC logo... you can find the .cap in the same thread.. I also updated the radio rom too, you can find it in prophet wiki.
Jesterz Rom is nice cause you don't have to uninstall anything, it's really clean and stable. it is by far better than NVID, but don't ask why cause i have to ramble a lot.
Oh by the way if you found out why this happened to us .. let me know
hofo_mofo said:
Still the same thing...i have treid 4.0.0.0.3a, 4.0.0.0.3, 4.0.0.0.4, 4.0.0.0.4s, 4.0.0.0.4sse, and Mobiz 2.0b3.....all nothing...
Sometimes it would be calnot.exe notification error, or replog.dll, or now clocknot.exe error...so far only NVID works
Click to expand...
Click to collapse
Try flashing PDAViet WM5 Temp
http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip PASSWORDDAVIET
or PDAMobiz WM5 Temp......
http://www.sharebigfile.com/file/178269/fantastic-b3-Step1-rar.html
and then try to flash truneytral's WM6 if you haven't already...
http://www.savefile.com/files/763142
If you don't want russian keyboard ,just follow DEVILDUCK's procedure here http://forum.xda-developers.com/showthread.php?t=302067&page=18
and follow the guide
http://forum.xda-developers.com/showthread.php?t=310452(just flash one of the above Wm5 temp roms,instead of NVid)
tonydeli7 said:
Try flashing PDAViet WM5 Temp
http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip PASSWORDDAVIET
or PDAMobiz WM5 Temp......
http://www.sharebigfile.com/file/178269/fantastic-b3-Step1-rar.html
and then try to flash truneytral's WM6 if you haven't already...
http://www.savefile.com/files/763142
If you don't want russian keyboard ,just follow DEVILDUCK's procedure here http://forum.xda-developers.com/showthread.php?t=302067&page=18
and follow the guide
http://forum.xda-developers.com/showthread.php?t=310452(just flash one of the above Wm5 temp roms,instead of NVid)
Click to expand...
Click to collapse
Okay, I spend another 2 hours to update the phone ! This time i didn't get the
Calnote.exe or replog error !! but my phone still doesn't work !
The phone connection is not stable ! it comes and goes ! and i get " Unknow SIM status. 3 attempts remaining. Only emergency calls can be made without a pin." well i tried different sim card , and i still get the same error !
HELPPPPPPPPP Pleaseeeeeee !
I just Upgraded my phone to ASreg3.3.12, and LvsW Aku2.3 and still doesn't work !!
I get the same error ! the Phone App doesn't function! I get Unknown Sim Status! I've tried NVID, and Jesterz Roms , both AKU 2 and both work fine !!
any suggestions ?
Strange, however, can you post which radio version you have when you switch roms ? it could a radio rom problem....
Hello All
my work has 100 mda vario's
but they all had windows mobile 5.1 on it
so i say to my boss i can flash it to windows mobile 6 with htc touchflo
he liked it so he let me do it
but it goes wrong
the mda vario does nothing anymore
just a bootloader cames up with : red green,blue,white
saying :
ipl 2.21.0001
spl 2.21.001
my idea is to get a working rom on a mini sd card and flash it from the sd card
but how to let the sd card starts load and let it flash,
not one button works in the bootloader
i have tried a lot of tricks i also have one time get restore to factory defaults.
but wont work, it says format completed, so no error's
thats good i think
but i really need to fix it.
otherwise my boss wont be happy
also active sync wont work anymore , the pc wont see the phone all .exe updates ultilty gives me errors that they dont get response from the phone
that comes because it only stays in the bootloader and the bootloaders has left under a usb sign, there stood usb
can this be fixed?
any help plz
Regards
R.G
hi there... 2 bad is the boss phone!!!
hi there... 2 bad is the boss phone!!!
first of all, try a hard reset, then plug once again the phone to PC
dont worry, activesync wont recognize phone at all (is just usb connection)
tell me if hard reset worked, and ill keep in touch
i kpnw there is a tool that would help you to fix the phone.... first try the hard reset!
Good luck
I got the same problem, the hard reset works, but the problem is there yet.
Ich hab das gleiche Problem, der Hard reset funktioniert, das Problem besteht jedoch weiterhin
Hello All
Thanks for u responses i like that
okay hard reset works
but nothing has changed by that
hard reset is the question with restore to factory defaults?
and than i get a screen with format complete.
Regards
R.G
hello All
i fixed it
i know get a green screen with ipl,spl, os
but everything is terrible slow
really slow i mean when i press start it takes a minute to show up
why is this?
plz help
i fixed it with abort all processes in task manager and use wizard love rom.
this is the only possible way i think
regards
R.G
R.G
You know what you did,whats wrong with the phone,you flashed a wm6 rom to a CID locked device.A CID locked phone cannot be upgraded to wm6,you must have a CID unlocked device for upgrading to wm6.
Now,as its a G4 device,it cannot be CID unlocked,but,however,it can be upgraded to wm6 through either SoftSPL or HardSPL method.
Now first recover back to its default status by downloading official stock rom and flash it,after it starts to work normal,then follow the SoftSPL or HardSPL method,only then it'll upgrade.
Hi,
im currently running the following setup:
phoenix 2.51
radio 1.71
hard spl 1.22
with o2 as service provider in germany.
since some flashing and testing i discovered that after a few seconds of speaking i get massive interferences in the call. my calling partner cant understand me, but i can hear him.
i already flashed back to 6.1 wwe official rom but the error still persists.
does anybody have ideas which could help me?
RsRichard said:
Hi,
im currently running the following setup:
phoenix 2.51
radio 1.71
hard spl 1.22
with o2 as service provider in germany.
since some flashing and testing i discovered that after a few seconds of speaking i get massive interferences in the call. my calling partner cant understand me, but i can hear him.
i already flashed back to 6.1 wwe official rom but the error still persists.
does anybody have ideas which could help me?
Click to expand...
Click to collapse
Try a different radio, eg 1.65.28.25. Works very well, and low power consumption to boot.
use other radio rom
I had the same problem.
Many noises, people on the other side couldn't hear me as well as dropping line.
I also tried different combination in spl/rom/radio (also restoring original spl/rom/radio).
I solved by sending phone to service reparing (warranty).
I don't know exactly what they did since ther was no physical repair but they said they only upgraded something (which sounds strange to me since ther's no official upgrade for my country from HTC) but now it works fine.
shinji_73 said:
I solved by sending phone to service reparing (warranty).
I don't know exactly what they did since ther was no physical repair but they said they only upgraded something (which sounds strange to me since ther's no official upgrade for my country from HTC) but now it works fine.
Click to expand...
Click to collapse
So, what's the build number of ROM and also radio number? If it is one not on the board, any chance of dumping the ROM and posting it?
i tried with 1.5xx roms, 1.65.28.25 etc. and still have the problem.....
rling said:
So, what's the build number of ROM and also radio number? If it is one not on the board, any chance of dumping the ROM and posting it?
Click to expand...
Click to collapse
Rom version: 1.31.408.09
Date rom: 10/30/07
Radio version: 1.58.16.27
Protocol version: 25.61.30.03W
It seems to be the "standard" configuration...
But now on the splash screen there's no more "Niki pro" trace...D 1.31 as it used to be.
ok... i again tried several configurations and also flashed the complete original rom. the error still is there what can i do now? is there any possibility to format the whole phone except the bootloader?
heeeeeeeeeeeeeeeeeeeeeeellllllllppppppppppp
RsRichard said:
ok... i again tried several configurations and also flashed the complete original rom. the error still is there what can i do now? is there any possibility to format the whole phone except the bootloader?
Click to expand...
Click to collapse
The radio, SPL and ROM cover the entire phone's OS. The official HTC WWE release 2.09.405.1 has all three in it. Disable the Hardspl (if other than HardSPL 1.22) by flashing the sspl, then flash this ROM. This will return the phone to original state. You might need to do this if you need to send the phone back for warranty service.
I'm going to send my phone to service again because I got my problems back...because I definetly think I got some "hardware" problems...
If I shake my phone some metallic noises can be heard inside, did you try something similar?
any news on this topic? i still cant use my niki.... im still receiving massive intereferences when calling since my flashing orgy. how to put it back to a fully OEM state without any mods?
nothing? will i really have to send my phone to the service ..... please not, i damaged one of the guarantee seels (back of the phone, right to the camera) mit the pen once....
RsRichard said:
nothing? will i really have to send my phone to the service ..... please not, i damaged one of the guarantee seels (back of the phone, right to the camera) mit the pen once....
Click to expand...
Click to collapse
it must be radio issue - please try to flash a complete rom+radio, flash from microSD this time, rename the nbh file to NIKEIMG.nbh, enter bootloader and flash.
*push* still not working
Hello,
used michys rom 6.1, works well. by upgrading to 6.5, upgrade stops at 92%. over and out..
I checked out to fixe it with the methods from xxacsxx, but still get : can´t synchronize with host, after use ´lnbs ...etc´ from mtty.
mtty also shows no info 2 page, interpret timeout.
I tried athena-unlocker again, it says not useabale for my device.
I also tried to upgrade with different rom, vanilla, michy, original t-mobile, chinese and uk.
I only com to the bootloader. Most rom-Updates say just :not for you phone, vannila and t-mobile say: wrong device id.
but this means i have to fix it via mac/mtty, or not ? and this does not work..
any ideas ? the bootloader screen is awfull beatyfull, but wm6 was it also...
thanks for your help,
Doktor.Wahnsinn
moin...
have you tried to flash any rom again? sometimes it helps you flash an original rom.
look at my page for info >> http://xacsx.de and original roms
doktor.wahnsinn said:
Hello,
I checked out to fixe it with the methods from xxacsxx, but still get : can´t synchronize with host, after use ´lnbs ...etc´ from mtty.
I also tried to upgrade with different rom, vanilla, michy, original t-mobile, chinese and uk.
Click to expand...
Click to collapse
i think you are this one i meant with the page xxaxsxx ? i checked all your roms, no positiv effect. i also tried nearly any rom, i got in my hands..
No Rom works, but i still came to the bootloader and can connect via mtty...
any further ideas ?
Thanks,
Doktor.Wahnsinn
..any ideas ?
i can´t update the device id. can´t synchornize with host at mtty; means this with host the athena, or the file-source,the pc ?
i´ve got no more ideas..
doktor.wahnsinn said:
..any ideas ?
i can´t update the device id. can´t synchornize with host at mtty; means this with host the athena, or the file-source,the pc ?
i´ve got no more ideas..
Click to expand...
Click to collapse
what method are you trying exactly? try my wifi mac/modelid fixer (stickied). follow instructions.
Hi cmonex,
I tried meanwhile different methods, all came to the same result:
1. xp,use mac1.exe, create bin for 1.2,rename to mac.bin and put in on c:\->deactiving wcescomm,mtty0512 (on c:\)->use usb-connection,connect->task32-> Level 0->lnbs mac.bin 75108000.
2. xp,use mac1.exe, create bin for 1.2,rename to mac.bin and put in on c:\->deactiving wcescomm,mtty11a (on c:\)->use usb-connection,connect->task32-> Level 0->lnbs mac.bin 75108000.
3. xp,use mac1.exe, create bin for 1.2,rename to mac.bin and put in on c:\->deactiving wcescomm,mtty142 (on c:\)->use usb-connection,connect->task32-> Level 0->lnbs mac.bin 75108000.
that´s it, no dialog box opens, no ok button appears, only after a few seconds: can´t synchonize with host.
For your information: your procedure works one year ago fine, as my device crashed during a rom-update. Do as you said, everything works well. But now after the crash during update to 6.5 this disaster.
Hope it´s not the end and the flash is broken...
greetings,
Doktor.Wahnsinn
if your bootloader shows the right informations, then use the sd-card-method (no sdhc).
it shows you, whats wrong (look at your (grey)screen). i have flashed my ameo for 500 times, a lot of crashes will be fixed with this method.
(mein englisch ist miserabel, weiss ich. beim flashen über die sd-karte zeigt das gerät alles an, was ok und was nicht ok ist. wenns geht ist gut, wenn nicht, dann wissen wir aber warum)
Hi,
i think my english is miserable, too.
Aber deutsch ist auch gut, aber nicht für dieses Board..
Ich werde es noch einmal mit sd-karte probieren, ich benutze das T-MOB005signed.nbh.
..i try it via sd-card with the t-mobile rom T-MOB005signed.nbh.
thx for brainstorming, i will post results.
greeting,
Doktor.Wahnsinn
it loads, then appears in red letters on the grey screen
00058002
and it starts up to the bootloader tri-color..
well frustrated..
..have a good night,
Doktor.Wahnsinn
you have to rename the *.nbh to ATHEIMG.nbh
make sure that your sd-card is not an sdhc-card (i think thats all cards over 4 GB)
HI,
I have renamed the rom-file correct; also i used a 2 GB SD Card..
greetings Doktor.Wahnsinn
..i tried 5 different sd cards, Sandisk,Kingston,Transcend from 512mb to 2 gb, also again all my available roms, always the same.. The fact that all card where functional under windos while the unit was ok it not important in this state of ´bios-booting´ or not ?
any further ideas ?
best greetings,
Doktor.Wahnsinn
Hi Doktor,
Did you solve the problem?
I have the same issue. I cannot upgrade with sd (formatted 1gb sd card with 2048 cluster size in FAT32).
I have to upgrade via SD card because i upgrade with wrong version (i have a 7501 and i did a upgrade with 7510 )
Thanks
Nelson
Can you please provide more info regarding what is displayed on Bootloader screen ? A screenshot/picture would help a lot mate
do you see:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.20.Olipro
or something else ?
MOVED TO ANOTHER THREAD BECAUSE HEADLINE ISN'T THE PROBLEM ANYMORE!
Got my 3rd Niki. As usual, I use sspl 1.16 (after 1st boot of original ROM) and hardspl 1.22 to unlock. But since unlocking the device always stucks in alignment/calibration screen, sometimes in screen before where you have to press once to continue.
I tried different ROMs (Original HTC and T-Mobile, some cooked ones), always the same.
Anyone an idea?
Update: I did hardspl with soft reset again, now alignment screens reacts, but always restarts (loop).
Update2: Toch screen doesn't work when keyboard is slided in, also accu status is 1%! It works as long it's slided out, also battery is shown right then. Very confusing!!
hi,
ich denke ich kann dir helfen, schalte mal deine PN an^^
------------------
hi,
i think i can help you but turn your PM on
its not software issue.
do not try to upgrade rom. coz this will not solve.
consult with a technician. and ask for touch screen replacement.