I need to restore my HD2 back to stock. First I was trying to remove HSPL as per the following procedure
4) Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Click to expand...
Click to collapse
I downloaded a stock rom and done the above and now I have the SPL screen as follows
SPL-1.42.000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x30
Upgrade ROM code error
Please try again
If I then try and put a stock ROM back on I manage 1% and then the phone restarts. I get the following error on the windows application.
ERROR [294]: IVALID VENDER ID
I have tried both a HTC stock rom and an O2 stock ROM and both give the error.
Any ideas?
check this out
http://forum.xda-developers.com/showthread.php?t=833875
Tried both O2 rom and general stock rom and neither will let me download because of my serial number?
Hello,
When i try to install HSPL3 i get an error message 'Wrong SPL version'. My SPL version is 3.03 is there a way to install HSPL again?
microgyn said:
Hello,
When i try to install HSPL3 i get an error message 'Wrong SPL version'. My SPL version is 3.03 is there a way to install HSPL again?
Click to expand...
Click to collapse
HSPL and stock ROM 3.14 (spl 3.03) isn't compatible sir.
I suppose you will flash a custom ROM!?
- First of all be sure the custom ROM have/use 3.14 stock ROM drivers.
- secondly use SSPL_RUU.exe
/Solved/
I downloaded the latest ROM from T-Mobile US's support site and it flashed properly. Then used HSPL3 to go back.
My HD2 was installed with HSPL and Android 2.2 NAND. I tried to flash stock 2.10.1 to restore it to default. Placed the LEOIMG.nbh on the root of the SD and booted into bootloader, used VOL Down to run, and received a ROM Install Failure.
Now when I boot into bootloader I am at SPL-2.08.0000 and on the green section it reads "Upgrade ROM code error Please try again".
The phone will automatically go into a grey screen with "Loading..." from bootloader but it seems to just sit there and do nothing.
Do you guys know what I should do? Thanks.
did you get 2.10.1 from the 'tmobile stock and test roms' thread? If so, its not a 'real' stock rom. It is stock, but its packaged like a cooked rom.
Use the 2.10.0 instead, or use hspl4 to apply hspl then reflash 2.10.1 over usb, then remove hspl again with hspl4.
hii i have a htc hd2 and it's stuck on 3 colour screen and i also have HardSpl 3.03 but when i try to flash official rom it stucks at 1% and i also cannot flash it via SD card
Can anyone help me out with this ? thanks a lot
You probably no longer have Hspl. The instant you try to flash stock from SD card Hspl is gone, (usually,, there are of course exceptions) even if the flash fails.
enter bootloader, what does it say next to spl?
firstly sorry for my english. i am new in this
my hd2 freezon htc logo,and i can't solv this problem. i tried to reinstall the rom, but the problem still persists. also i tried to boot a nand android rom, and also didn't worked, i can't inslall ClockWorkMod Recovery (i think this is the problem),if some one can help me i would be very thankful
tmous or regular?
flash hspl yet? what does it say in bootloader?
flash anything that successfully boots at all yet?
samsamuel said:
tmous or regular?
flash hspl yet? what does it say in bootloader?
flash anything that successfully boots at all yet?
Click to expand...
Click to collapse
Tmous, and i flashed hspl,in bootloader says pb811 ss-b3
spl-2.08.hspl 8g xe
0x05
cotul lahspl 0x50
serial
and i succesfuly installed magldr v1.13
Ok, so once magldr is installed, can you enter magldr by holding power at boot?
YES, I CAN. AND I try to COPY THIS FILES initrd.gz AND zImage to sd card, after i enter in usb massStg,and some times it works,some not.if i copy the files,i must do a reset,but it doesn't work,and and when i press the reset button near battery,i recive a error 1fatal hit 1,and here i don't know what to do. sorry again for grammar mistakes
That's old cwm,it runs from the nand in later versions.
Go get "nand toolkit" in android dev thread, put phone in magldr, choose "USB flashing" and in nand toolkit choose partition size...... well, read the toolkit instructions, first posts.
Then once cwm is installed, enter magldr and choose 8-ad recovery,,,if 8isnt that option, update magldr thru the toolkit.
I can't find where to download nand toolkit, now is late,i will tomorow search better,but today I didn't find nothing on it
i found the hd2 toolkit,but i don't know what "Choose the partition size you want to install and choose cache size you want to install." what values should i choose ?
Pick a rom, ,, in post 1 it will tell you what to choose. Example, typhoon (and most cm7 roms) will use a 150 system partition, whilst sense roms need 200plus,, for cache, 5 seems to be common, tho some use bigger, its less important than the system size. Tho.
and also i can't install device driver softwoare,before installing the cLK insall recovery. my computer can't find the driver for the phone at this step. what should i do??
and i want to ask you to write without abbreviations because i don't understand all what you want to say. thx