Hi i have recently flashed to gingerbread on my galaxy ace on the orange uk network.. since then i can not send text while packet data is turned on.. i then flashed back to froyo and it all worked fine..
Is it posible i can mix files from froyo & gingerbread while flashing with odin..
eg (CSC & MODEM) from froyo & the rest from gingerbread..
Please could you help me out..
Regards
Aron
I believe you could. Anyway, flashing csc and modem files will not fully brick your phone so you can try.. if it does go into a bootloop, remove battery, put it back in and start download mode again.
can i just flash the csc file from froyo (sms text working) to the gingerbread (sms text not working) without reflashing the all other files..
Please can someone explain to me what the PDA, CODE, MODEM, CSC files do, or point me in the direction of a tread that will..
Hello, mate! Looky here...
http://forum.xda-developers.com/showthread.php?t=1204788
Related
I had a JI6 Vibrant and needed to network unlock it, I did the nv_data.bin modification and put my own network unlock code.
I went back from JI6 to stock JFD and was running the phone on AT&T network. I Have been using Macnut since version 5 and have been using v12 since the day it came out. Yesterday I upgraded to V13 and all was great, I went in to market and downloaded all of my apps, set up my contacts ..... I then enabled the 850 band and rebooted the phone and that is when I lost network connectivity.
with Macnut V13 I have been unable to get on the network, I go into about phone and it is unable to determine the baseband. I try flashing one of the modem files with odin and it does not work.
Used clockwork to revert back to R12 (clean install and also tried restore backup) and no dice.
I then flashed stock JFD using odin and I had network connectivity again, so I tried Macnut V12 again but once I did that baseband not identified and no network connectivity.
I reflash JFD using odin and my phone worked again, so I tried the JK2 odin rom from Eugene but that did not work, no network connectivity and cannot identify baseband
I reflashed the new JK6 release and again same issue, no network connectivity.
I am currently running stock JFD, can anybody help please? after about a month on Froyo JFD is slow as ....
I searched and most of the unknown baseband threads do not have solutions, and the ones that suggested removing the sim card/sd card/ usb and rebooting multiple times has not worked for me.
I really hate being stuck at JFD
Thread moved to Q&A.
Anybody?? It seems a few people have the problem but nobody has a solution
I have a similar problem. I deleted my nv_data.bin stuff on accident and one thing led to another. Now I can't connect to any service at all and my baseband says unknown. I've been trying to flash it with all different kinds of roms and finally got my baseband to say something but I still can't connect to anything.
No luck Still got Unknown Of Everything
Hi if somebody can help i have a similar problem got UNK baseband, phone, Network, service, try the nv_data.bin fix, no luck, try odin back to stock, no luck, the phone works on wifi perfectly and every thing else works exep cell functions, on mobile says "no simcard found" any help would be greatly appreciated..
I went back from Cm7 to JFD stock rom and flash Simply Honey now my mobile can't recorgnize my Sim card. I checked and saw a problem "Baseband version : unknown". *#06# show NULL/NULL.
Anyone know how to fix it, please help me ??
Thanks
I had the same problem with Simply Honey -- simply didn't recognize the sim card. No other rom I installed ever did that.
Hi,
I've had my Samsung Galaxy SII (GT-i9100) since around 10th of May this year. It came with a firmware ending with *1, but the first thing I did was to upgrade it to XWKE2 via Kies on my PC. That was a good firmware. I had no problems with it ... The only annoying part was that the camera made shuttersounds all the time, even when the phone was silenced to vibrate only. That was fixed in XWKF3 which I'm running now. The MAJOR problem with XWKF3 is that the radio/modem is ****ed up beyond recognition.
On KE2 I had like H or H+ all the time, and if no H/H+ I had E. Nothing in between. Now I see 3G almost more than I see H/H+, even though I'm in the same areas as before. Also when my phone goes toggling between 3G and H or stays on 3G - I do not have Internet access. It's like a huge "no route to host" appears on 3G, or if the phone toggles and cannot agree on ONE thing.
So I would like to upgrade the radio only. Why? Well I've been trough a few of the original firmwares from samfirmware.com and here, Mostly XWKE2 (which made my phone loop on boot), XWKF3, XXKG6 and XWKG3 (I think). Main problem with XXKG6 was that it didn't have Norwegian (for Swype or keyboard at all, but UI was present in Norwegian). Others was either looping on boot or I was using them to upgrade back to the original firmware (now XWKF3 with radio XXKE7 and XXKF1 for CSC).
Two questions ... Can I use Odin (I've got 1.85 as the latest) to upgrade ONLY the "Modem"-part? From XXKE7 to XXKG6?
Is there a way to get Norwegian Swype on the XXKG6? Maybe "keep" an older NEE-based CSC? Because .. Swype is a part of CSC not PDA/Code, right?
Two questions ... Can I use Odin (I've got 1.85 as the latest) to upgrade ONLY the "Modem"-part? From XXKE7 to XXKG6?
Click to expand...
Click to collapse
Yes, you can upgrade the modem separately.
Is there a way to get Norwegian Swype on the XXKG6? Maybe "keep" an older NEE-based CSC? Because .. Swype is a part of CSC not PDA/Code, right?
Click to expand...
Click to collapse
swpye is not part of the csc, the language only is part of the csc.
Swype is app that can be updated or installed seperately and has links to the csc.
Untar the file using something like 7-zip.
Just use the modem.bin, and tar it back using 7-zip, flash with Odin under phone.
If not, you can download one of the Clockwork version, and replace the modem file, then rezip and upgrade with Clockwork Recovery.
Flash your Modem KG6 and Flash CSC KF1 for your area Modem in Phone and CSC in CSC via Odin . A CSC is only a bunch of text files with network details language etc .
jje
So summarized ... I can use Odin and _only_ tick "Modem" and pick the XXKG6-Modem, or do I need a CSC as well? I have today the Stock XWKF3, with radio XXKE7 and CSC KF1. The only ****ing thing bothering me with this stock rom, is that the radio went FUBAR after update (compared to how it behaved on XWKE2)
Cosmic Blue said:
swype is not part of the csc, the language only is part of the csc.
Swype is app that can be updated or installed seperately and has links to the csc.
Click to expand...
Click to collapse
So ... With XXKG6 (to differ from XWKF3) I will not get Norwegian Swype, even if I custom with Odin to keep my KF1-CSC? I will have to wait for a XWK*-release of Android 2.3.4 to have my Swype with norwegian dictionaries?
you can flash the modem only.
csc is used in relation to your swype question.
Will do a flash of my radio later tonight after work then. I really hope it goes more stable again. Samsungs Customer Service is crap ... "Have you tried to reset your phone?" - "Yeah, your radio software still sucks!" ... "Well sir, try to fabric reset your phone" - "Say that again, and I will strangle you!!" ...
Hi. I have the Canadian SGS2 from Virgin Mobile.
I want to update the firmware on the phone but Im unsure as to which one to use. Right now the latest firmware for this specific phone is UGKG2. My model number is GT-19100M. Im just wondering which firmware would be the best to update to. Ive been having a few issues with my phone and apparently updating the firmware is suppose to fix it (like the Wifi sharing garbage that starts every time you tun wifi on, but doesnt go away when you turn it off)
Anyway - which firmware would be best to update to, or if it would be best to just update to the latest which I think is XKH2.
Help is appreciated. Thanks!
Yeah sounds like you are on an older firmware which a lot of us battled back in May with the wifi-sharing battery drain. You'd be safe flashing any ROM really. Not sure if you prefer stock firmware only or not as some of the custom roms are great. I'd suggest KH3 as many bugs have been fixed that are evident still in your ROM. But you may want to check to see if anyone has a backup of your current rom in case you need to take it in for warranty. I have an i9000 but friends who are using i9000m Bell model are able to flash any i9000 rom without issue as there really is no difference from what I know. If you do flash, keep in mind that your boot logo will say i9000 and not i9000M, which is why you may want to look into backing up your current rom (by rooting and flashing a custom kernel to make a backup) just in case you need to flash back for warranty repair.
I use Batista Rom and really like it but I always tend to prefer custom roms. I think you'd be better on any newer rom, stock or custom to get rid of the bugs you got in that firmware you're on
so to be clear - I can download KH3 and use Odin to flash without issue, Even though Im on the stock I9100m Virgin Phone? And KH3 is a single TAR file that needs to be placed under PDA correct? I basically just want my phone to be the exact same as it is now except with the firmware updated.
Will anything be different or will it all seem the same as if I were to do a factory reset right now?
Also where KH3 is 2.3.4 and my phone is currently 2.3.3 - this wont lead to issues when using Odin?
Thanks for the replies.
Ryne said:
so to be clear - I can download KH3 and use Odin to flash without issue, Even though Im on the stock I9100m Virgin Phone? And KH3 is a single TAR file that needs to be placed under PDA correct? I basically just want my phone to be the exact same as it is now except with the firmware updated.
Will anything be different or will it all seem the same as if I were to do a factory reset right now?
Also where KH3 is 2.3.4 and my phone is currently 2.3.3 - this wont lead to issues when using Odin?
Thanks for the replies.
Click to expand...
Click to collapse
Yes you can flash KH3 using Odin under the PDA section. Depending on where you downloaded the KH3 firmware it probably wont wipe your phone so I normally do a factory reset after just to make sure it's a clean install. Make sure you back up anything you don't want to loose. Also take note that the KH3 package includes files that will change your boot up image from I9100M to I9100. If you want to keep things as close to stock as possible you can remove these files from the package since you don't really need it: boot.bin/sbl.bin/param.lfs. All you need to do is use winzip or 7zip, double click on the .tar file and delete.
Haha. Thanks for the replies.
I'm happy to say that everything went without a hitch - and all of my problems have been solved. One funny thing, was the camera shutter sound - which from what I read is suppose to be hardware related - was actually fixed as well - no more sound when opening the camera app.
Battery Improved
Wifi Sharing bug = gone
Shutter Sound = gone
Random restarts while listening to music = gone
And I got list view
Thanks guys!
im in the same boat. i just got a galaxy s2 a couple days ago. I just want to flash my phone to 2.3.4. Which firmware do i download? Where did you find KH3? thanks
I have a Samsung Vibrant-
I flashed Simply Stock 2.3.5 to it, loved it
but,,, what I did not know, is I was not receiving calls...
It seems as this is an issue that others have seen, what was / is the fix?
thanks!!
I am also having the same issues after flashing
Simply Stock 2.3.5 with a simply.stock.JVS.Talon.kernel. I even tried the bullet kernel and I get the same emergency calls only error "No service- selected network (my network) unavailable). the only time this Simply Stock 2.3.5 rom works for me is when I use its stock kernel.
ok I finally figured it out,
after odin you have to flash either "Asgard_32_0821signed" rom or "Malice_v5_EDT" and then you have to flash on top of either of these 2 roms simple stock 2.3.5
do this if it helped me I see no reason it wont help u.
I flashed a stock 2.3.5 rom, using odin after I almost bricked my phone. Upon starting up my phone I immediately got the error that I could only make emergency calls. The strangest part of this is that my service state flicks on and off between in service and out of service, and my roaming switches randomly between not roaming and roaming. My provider is Telus and I have a sim card, and I'm pretty sure it works, I bought my phone from Telus.
My phone is able to connect to Kies.
Upon dialing *#1234# I get
PDA : S5830XWKS9
PHONE : S5830XWKS2
CSC : S5830XEOKP2
This CSC is for Poland, the rom I flashed was set to Poland for some reason, is this an issue? I live in Alberta, Canada, so my CSC code should not be set to this. I found a Telus CSC on this page in post #10, so I might try flashing that rom to see if that resolves my problems.
http://forum.xda-developers.com/showthread.php?t=1390798
I also noticed that the PDA and PHONE last few letters are different(WKS9/WKS2) is this also an issue?
Additional information
Baseband version : S5830XWKS2
Kernel Version : 2.6.35.7-perf-CL654989
[email protected] #1
Build Number : GINGERBREAD.XWKS9
You can see more examples of different numbers when you look at this info, the Baseband version is WKS2 and the Build number is WKS9.
Should I phone up Telus to make sure I'm not being charged roaming fees while I am most certainly in their coverage area? And would it be possible that my imei number is blocked for some reason(The one on the battery is the same as the one in about phone and also the same as the one when you dial *#06#).
Although my phone does work sporadically I really want it to work 24/7 for a number of reasons including safety.
Any and all help is greatly appreciated, feel free to ask me for additional info, I'll do my best to get it.
Edit: My brother has a relatively new Galaxy Ace, also from Telus, exact same settings and everything I want, would it be possible to get CWM recovery on his phone and copy all the settings to my phone and restore my phone to his settings, bypassing having to screw around with all the settings on my phone?
The person in Post #8 on the site below said doing this worked for him(Although I don't understand why he replaced CWM with Ultrajack)
http://androidforums.com/huawei-m835/405469-apn-question.html
Ive also heard that you can remove your sim card and your sd card from your phone, connect it to odin and flash something to restore your phone to defaults, would there be any way to do this?
Edit: I solved this problem by finally finding the stock firmware for Telus here..
http://hotfile.com/dl/137128537/a629597/GT-S5830D_TLS_S5830DTLKI4_S5830DTLSKI4_S5830DTLKI4.rar.html
worked great, just flashed it in Odin, started up my phone and all the baseband, CSC, everything was the correct format(TLKI4), I think this works for Koodo as well, so if anyone has been facing some issues with their stock rom, just flash this one and any errors should be cleared up.
Please try flashing a full package Froyo
Herpderp Defy.
Did you flash a new baseband? On a possibly related note... I have the DTLKI baseband, and it comes on Koodo phones. Koodo is a Canadian subsidiary of Telus. I had flashed a new baseband on and had the same problem as you, it wouldn't pick up my network provider and luckily someone on here had uploaded the baseband I needed to pick up Koodo again. Maybe you're having the same issue? Try going to wireless & networks/mobile networks/ and then network operators. Check if you can find Telus. (if this is irrelevant, I apologize)
Yeah my brother phone has DTLKI baseband as well, do you have any links to that specific baseband? I can find Telus(and also Rogers for some reason), but using the right baseband couldn't hurt.
If I did flash a full package Froyo, could I connect it to Samsung Kies to update it to 2.3.4/2.3.5? I've also read on a lot of sites that Koodo/Telus Galaxy Aces have difficulties if the baseband isnt TLKI4 so if you know of any full package froyos that use that baseband version I would greatly appreciate it.
Well, you'll want to flash the modem with odin. and the modem only. I don't know if it's compatible with froyo though as I've only used GB myself. I'll email it to you. I received it from Kevinlekiller a long time ago. The filesharing site is now removed now though! It's worth a try if you don't have a limb to go on though I guess.
Gonna try it
How did you find that firmware? I looked all over the place for it and finally found your thread!
Gonna try it tonight, my CM makes my gps crash. No fix whatsoever. Hopefully this will restore it.
Worked!
Yay!
by the by, did you happen to lose GPS functionnality while flashing custom roms?
Forget that last question
Flashing back the stock firmware corrected all issues I had and now, all other firmwares are working A-OK.
Currently on ice cream sunday.