Related
Hi Folks,
I was having the issue with my Vario II (on my 3rd Handset) where the phone enters standby and never wakes up until a soft reset.
When the 3rd handset arrived I decided to bite the bullet and go for WM Black and see if it made the handset any better. Unfortunately, as good as the new ROM (now on V2) is, it didnt solve my hanging issue.
The next thing I decided to do was change the radio ROM. I first went to the 1.38.10 and then to 1.38.11 and then to 1.27.00, as the later was decribed as being the most stable.
As you have probably guessed by now, the issue still plagues me....Even more so since the radio upgrades. The symptoms are as follows;
- Some calls I answer go silent after around 30 secs and I need to soft reset
- The phone can show full bars of signal but the phone diverts to answering machine
- When connecting to the internet, the icons shows as connecting but then drops to no signal (showing a !) then after a while will start to reconnect. Sometimes I need to soft reset to get the connection again
I am wondering if there is something else I am missing that could be causing the issue. I am using it today with no apps and still have the same issues as above plus the freezing issue.
Is there anything else I can change???? or am I just cursed?
Any help would be much appreciated.
Cheers and thanks in advance
Aidan
I would say, try your SIM card in a TOTALLY different phone (not just a different Hermes) As you would have to be fairly unlucky for it to happen with THREE seperate devices, especially with different ROMs also.
If there is a handset available to you that is either a tmobile or SIM unlocked.....give it a go.
mrvanx said:
I would say, try your SIM card in a TOTALLY different phone (not just a different Hermes) As you would have to be fairly unlucky for it to happen with THREE seperate devices, especially with different ROMs also.
If there is a handset available to you that is either a tmobile or SIM unlocked.....give it a go.
Click to expand...
Click to collapse
I belive it's your SIM card also..ask your provider to replae the SIM card for you. Just tell them your issues and it happened to three handset with the same SIM. I bet they will able to replace the SIM card without charge.
trashcan said:
I belive it's your SIM card also..ask your provider to replae the SIM card for you. Just tell them your issues and it happened to three handset with the same SIM. I bet they will able to replace the SIM card without charge.
Click to expand...
Click to collapse
Yep SIM cards cost JACK ALL to the providers. If they do charge you then thats gotta ring alarm bells!!!
Hanging on wake-up was my big disappointment when going from Vario I to Vario II.
It decreased after upgrading to WM6 (first black 1.2, now black 2.0). In my case the SPB mobile shell also did not seem to do the problem any good, probably because it starts the 'now' screen on wake-up.
I have not much software on my device and have very few hanging issues.
I work for a Cingular retailer, and I just signed my fathers business up. Someone had told me that the IMEI on the account had to match the phone on a 3g phone or the exact same symptoms you are seeing would occur. I confirmed it with my pop's business. the three people using 3g phones had serious problems with calls going to VM, not getting txts, and poor service in general. Once i fixed the serial numbers Cingular-side, everything was peachy. This happens to be my first post (longtimelurker) so if I'm full of ****, feel free to tell me. Check with your service provider and make sure they have the right IMEI on file. If not, you'll prolly have to go to a store to have a clerk fix it, but it'll be worth your trip if im right .
Hope I helped.
luggyman said:
I work for a Cingular retailer, and I just signed my fathers business up. Someone had told me that the IMEI on the account had to match the phone on a 3g phone or the exact same symptoms you are seeing would occur. I confirmed it with my pop's business. the three people using 3g phones had serious problems with calls going to VM, not getting txts, and poor service in general. Once i fixed the serial numbers Cingular-side, everything was peachy. This happens to be my first post (longtimelurker) so if I'm full of ****, feel free to tell me. Check with your service provider and make sure they have the right IMEI on file. If not, you'll prolly have to go to a store to have a clerk fix it, but it'll be worth your trip if im right .
Hope I helped.
Click to expand...
Click to collapse
I don't think IMEI is the issue here. I just signed up with Cingular and got a Motorola K1..but the SIM is a 3G sim. I simply pop that into my Hermes and it's been working for 2 month now without any issues. Another thing with Cingular...the IMEI on their database is automatically updated..it's not like you have a Motorola phone and switched the SIM to a SonyEricsson phone and still using the Motorola IMEI #....it will not work that way. In fact, all GSM providers will automatically update the IMEI in their system once the SIM is registered in their network. I can confirm that with my HTC tytn with the Cingular's online account. You can check the online account pretty much on what type of phone you current have. If I use the Motorola K1, the online account will be updated as unknow phone due to it's new I guess...but when I use the HTC tytn..it's automaticlly updated as HTC 8525...even I manually change the phone type to other phone...after couple minutes..I log back on and it will show the HTC 8525 again. Base on this, I am sure IMEI is not the issue here. One thing to note is that I did get that hanging on wake up when I have the SPB software installed.
i can concur about the IMEI... i havent changed my IMEI on my account since i had a sony ericsson a few years back... and i have no data problems.. i take that back, i had some when i first got the 8525, but then found out i needed the white 3G sim, since then it has been flawless.
Awaiting Sim
Thanks for all the advice. I tried the phone with someone elses sim card the other day and it seemed to behave itself. I am going to phone t-mobile and ask them for a replacement SIM.
Will let you know how I get on.
Cheers
Aidan
AGGGHHHH!
It doesnt get any better....
I just phoned T-Mobile and asked them for a replacement SIM to be sent out. The girl I spoke to said that she could order me a new SIM which would be out in between 1-3 days but she would have to disconnect my current SIM when the new one was despatched! This means no phone for this time, which I need for business
I asked whether I could phone for activation when the new SIM arrived but this she tells me is not possible.......AGGGGHHH!
She did suggest that I could pay 15quid for an 'interactive' swap over at a T-Mobile store but I have issues getting to a store during the week and they are then going to see that VM6 Black edition is on the phone!
Any suggestions?
aidanbree said:
It doesnt get any better....
I just phoned T-Mobile and asked them for a replacement SIM to be sent out. The girl I spoke to said that she could order me a new SIM which would be out in between 1-3 days but she would have to disconnect my current SIM when the new one was despatched! This means no phone for this time, which I need for business
I asked whether I could phone for activation when the new SIM arrived but this she tells me is not possible.......AGGGGHHH!
She did suggest that I could pay 15quid for an 'interactive' swap over at a T-Mobile store but I have issues getting to a store during the week and they are then going to see that VM6 Black edition is on the phone!
Any suggestions?
Click to expand...
Click to collapse
What the hell?!?! Thats bullcrap if ive ever heard it, when i got a replacment USIM from O2 my existing one worked until i called O2 to activate the new one? Maybe T-Mobile has a backwards way of provisioning them?! That sucks dude. Suggest you call them again (if you havent already got an order through) and do another request...you may hit the jackpot with a different operator?!
mrvanx said:
What the hell?!?! Thats bullcrap if ive ever heard it, when i got a replacment USIM from O2 my existing one worked until i called O2 to activate the new one? Maybe T-Mobile has a backwards way of provisioning them?! That sucks dude. Suggest you call them again (if you havent already got an order through) and do another request...you may hit the jackpot with a different operator?!
Click to expand...
Click to collapse
As far as I understand how GSM works...The T-Mobile lady is correct. You can't have the two SIMs having the same #, one has to be deactivated before the new one is active. But if you are sure the new SIM will get to you in a day or two, you can have them to schedule deactivation of the old SIM two days later, schedule the new SIM to be active in two days..the only donw time you have is probably a an hour or two if the timing is correct. If you are able to go to a T-mobile store for direct swap, you can get the new SIM working within an hour but they shouldn't be charging you $15 at the store even you have WM6 black on the phone becasue the phone is not faulty, the faulty part is the SIM and they should honor their warranty.
trashcan said:
As far as I understand how GSM works...The T-Mobile lady is correct. You can't have the two SIMs having the same #, one has to be deactivated before the new one is active. But if you are sure the new SIM will get to you in a day or two, you can have them to schedule deactivation of the old SIM two days later, schedule the new SIM to be active in two days..the only donw time you have is probably a an hour or two if the timing is correct. If you are able to go to a T-mobile store for direct swap, you can get the new SIM working within an hour but they shouldn't be charging you $15 at the store even you have WM6 black on the phone becasue the phone is not faulty, the faulty part is the SIM and they should honor their warranty.
Click to expand...
Click to collapse
Agreed on the warranty there dude.
O2 simply sent out a replacment USIM, obviously not activated yet. It arrived and i called them, they took the sim card number and said I should lose reception on my existing sim (it wasnt 3G ready) and thats when i should put the new one in, as soon as i lost reception i swapped and it was working (got the U symbol straight away).
I figure T-mobile would do the same?!?!
Bit the bullet yesterday and paid 15 quid for a new SIM card. It has made he haw difference. Still got major issues. The phone has no signal most of the time and even on the rare occasions when it does, the calls go to answerphone.
The signal shows an exclamation mark (!) and the only way I can get rid of it is to do a hard reset and it works for a couple of hour (or less). It is as though it is constantly in flight mode.
Hi guys,
i used a sim unlock code to unlock the ATT locked Atrix 4g, for use with a european sim card (mobitel, slovenia). it unlocked fine and i could call, but the wifi stopped working it just didnt scan/find or even connect to remembered wifis (home router), which worked perfectly before the unlock. so than i thought it might help to factory reset it, and now the problem persists and i cant even finish the wizard, cuz it wouldnt connect to the cellular (which we have 2g and 3g here) and the wifi has the same problems (so initially it finds all wlans, than after like a few secs it looses them all, i can turn off the wifi and turn it on again and the same thing happens). so i am wodering if anyone has any idea how i could rescue the phone ...
thanks in advance
ok guys i did a hard reset and put in a nonworking sim (doesnt connect to network) and i got the wifi back to working and managed to activate motoblur again. so after that ive put my working sim card in again (3g+ hsdpa+ able), and the wifi stops to work again/behaves the same as i described before. terrible ... anyone has an idea how to fix that ?
ok, more problems, now after ive put the working sim inside and the wifi stopped working, i tried with the nonworking sim (that wifi worked great before with), and the wifi isnt working with the sim it was working before either and even if i try without any sim it doesnt work... ill try with a third sim now and if it wont work ill hard reset it again
Same problem
I have the same exact issue. Anyone know what to do? I can't imagine that this is "bricked" because everything else works fine... thoughts?
where did you guys get the unlock code from?
Actually, I have a similar problem. After entering unlock code the phone accepts my SIM card, but I cannot activate 3G connection. GSM is working, try to call my other phone. APN settings are correct.
In the "hidden" settings menu (*#*#4636#*#*) I cannot chose between radio bands, but only the USA radio band.
Any ideas? Will I need to root it or even put a custom ROM (if it exists)?
So you guys used an unlock code from someone other than the carrier and are now having issues?
Wish I could help on this one. If you used an unlock code from someone other than the carrier, I would contact motorola support.
If you used a piece of software, I would wager that the software broke something and you might as well warranty return it for another.
Sent from my MB860 using XDA App
DarrellRaines said:
So you guys used an unlock code from someone other than the carrier and are now having issues?
Wish I could help on this one. If you used an unlock code from someone other than the carrier, I would contact motorola support.
If you used a piece of software, I would wager that the software broke something and you might as well warranty return it for another.
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Don't be offended, but I don't think this is the case. AT&T locked their phone to their network with standard network code (as seen in many other phones for years) so that "alien" SIM card would not work. But, additionally, since the AT&T has some value added services on their data plan (like wifi tethering) they made some accommodations (read: locked parts of the android configuration).
I am not a developer, this is just my guess, but it seams sane and probable.
gogy22 said:
Don't be offended, but I don't think this is the case. AT&T locked their phone to their network with standard network code (as seen in many other phones for years) so that "alien" SIM card would not work. But, additionally, since the AT&T has some value added services on their data plan (like wifi tethering) they made some accommodations (read: locked parts of the android configuration).
I am not a developer, this is just my guess, but it seams sane and probable.
Click to expand...
Click to collapse
No offense taken. This is why I asked about a program. Using an unauthorized code to unlock it may over write a.setting or file. Its also possible that someone broke something using adb.
Best solution, warranty it and try again
Sent from my MB860 using XDA App
ok. anyone with unlocked phone has a wifi problems besides these 2 nice people ?
I don't have a WiFi problem, I have a 3G problem
Sent from my HTC Desire using XDA App
gogy22 said:
I don't have a WiFi problem, I have a 3G problem
Sent from my HTC Desire using XDA App
Click to expand...
Click to collapse
Sent from my HTC Desire using XDA .....
can you guys tell us what website you use to get your unlock codes from so we can avoid them? thanks
man.. this forum is dead.
even the OP stopped coming here to check his post :/
Based on your replies, I'm guessing you've never unlocked a phone before...
Unlocking a phone to be used for a different carrier affects nothing else but the ability to only use the SIM Card of the carrier you bought the phone from.
To unlock a carrier-locked Motorola phone, you simply need a "Network Unlock PIN" which is an 8 or 16 digit code that you enter to unlock the phone to any network. There is no software installation ivolved in the process.
A 3G issue will occur when your carrier doesn't support the 3G bands that the Atrix supports. Which would be: 850/1900/2100. If your carrier doesn't use any of these bands for their 3G network, then of course you are going to have 3G issues.
The Wi-Fi problem that the OP is having may be as simple as him having an antenna QA issue. But it could never be the Unlock Code.
Unlocking your phone and using another carrier other than AT&T has nothing to do with Wi-Fi issues...
DarrellRaines said:
So you guys used an unlock code from someone other than the carrier and are now having issues?
Wish I could help on this one. If you used an unlock code from someone other than the carrier, I would contact motorola support.
If you used a piece of software, I would wager that the software broke something and you might as well warranty return it for another.
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
DarrellRaines said:
No offense taken. This is why I asked about a program. Using an unauthorized code to unlock it may over write a.setting or file. Its also possible that someone broke something using adb.
Best solution, warranty it and try again
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Beach_Head said:
The Wi-Fi problem that the OP is having may be as simple as him having an antenna QA issue. But it could never be the Unlock Code.
Unlocking your phone and using another carrier other than AT&T has nothing to do with Wi-Fi issues...
Click to expand...
Click to collapse
I got my unlock code from cellunlock.net. It unlocked my phone just fine. Don't use that as a reason to avoid cellunlock.net. Unlocking is unlocking.
I have swapped back and forth between my prepaid sim and My AT&T SIM about 5 times so far.
WiFi disconnects almost immediately when I try to connect with my prepaid sim inserted, but I can make calls. (Atrix also displays H+, which can't be right)
With my AT&T sim everything works fine, solid as a rock.
I may do a factory reset to test things, but I have a feeling it has something to do with drivers or the network stack on the atrix, or perhaps because my prepaid sim has no data plan. It certainly isn't a hardware problem with the antenna. I am afraid to do a factory reset on the atrix while I am out of the country, considering that it requires network access to unlock itself.
To the original poster:
When you put a non-connected SIM into the phone, if you do a power reset again, the wifi comes back up solid again.
Also, is there some way we can request a merge of these two threads?
http://forum.xda-developers.com/showthread.php?t=986499
how come only you 2 have this problem ? do you 2 live in the same country ?
this is really surprising :/
It really is quite weird...
ll_l_x_l_ll said:
how come only you 2 have this problem ? do you 2 live in the same country ?
this is really surprising :/
Click to expand...
Click to collapse
I was merely suggesting that it could be a multitude of things, but never the unlocking code or the process of unlocking itself.
Also, it can't be your SIM because your SIM has nothing to do with Wi-Fi. If we were talking about GSM and 3G then SIM cards come into play. Other than that, no way.
Have you tried using the phone without a SIM? Do you get the same problems?
wstutt said:
It certainly isn't a hardware problem with the antenna. I am afraid to do a factory reset on the atrix while I am out of the country, considering that it requires network access to unlock itself.
To the original poster:
When you put a non-connected SIM into the phone, if you do a power reset again, the wifi comes back up solid again.
Also, is there some way we can request a merge of these two threads?
http://forum.xda-developers.com/showthread.php?t=986499
Click to expand...
Click to collapse
Beach_Head said:
I was merely suggesting that it could be a multitude of things, but never the unlocking code or the process of unlocking itself.
Also, it can't be your SIM because your SIM has nothing to do with Wi-Fi. If we were talking about GSM and 3G then SIM cards come into play. Other than that, no way.
Have you tried using the phone without a SIM? Do you get the same problems?
Click to expand...
Click to collapse
I agree that it has nothing to do with the SIM or unlocking.
I just tested. I get the same problem with no SIM inserted. Screw it.. doing a factory reset and seeing what happens.
Edit:
Still does the same thing. But now I have to re-activate app sideloading.
Also, you can reactivate over wifi, which is nice.
I have just purchased an unlocked Dell Streak 5 from ebay, I put my GoPhone SIM card in and booted it up, and I'm not prompted with any unlock screen, and it doesn't say my SIM card isn't inserted or isn't invalid. But I have no service and cannot connect to any network via the Wireless & Network Settings, I have called AT&T Support multiple times and have not received any useful help. They have changed the IMEI of my SIM to match my Dell Streak 5 and I still have no service. I have just got off the phone with someone who has made the most sense of all the representatives I've talked to. She said a previous person had updated my information of my account and that it may take up to and hour for the information to update, and I was told I would receive a call back in about an hour to unlock my SIM card i guess. I'm not 100% sure what that means, because I've used this SIM card with 3 previous different phones, all have worked. So I don't know how if my SIM is locked that I was able to do that. Some feedback on this issue would be greatly appreciated. I don't want to have just wasted $300 on a very nice phone that I cannot use. I'm very much into tech and I need this phone working!
more information:
Dell Streak 5 running froyo 2.2.2
Ebay seller stated phone was unlocked to all GSM carriers
My GoPhone plan is unlimited talk&text (i'm not worried about not having data plan) So I hope this helps shed some light on this subject. Thanks in advance!
other notes:
I have tried playing in my apn settings, and searching for networks. AT&T shows but I cannot connect
I've ran into the issue where one my really old tmo sims didnt work in it, the sim itself was no longer valid but my iphone detected it properly.
Used a newer expired sim and it was detected properly. I dont know if this helps but you could try a different gophone sim
thanks for the reply. I'm not sure if it's my SIM, I feel it's not. I purchased my SIM less than a year ago so it's fairly new. Any way of checking the age of a SIM? also I have no other SIM cards I can try. at the moment my hope rests on AT&T support calling me back with good news.
Ok sorry for the double posting, but I have tried my buddies AT&T SIM card, which looks older then mine in regards to the graphic wear on it, but it works in my Dell Streak?! Does this help shed any light on this? I'm not understanding why his SIM card works, we're both AT&T only difference is he's on a contract. So i'm really stumped, I would really appreciate any help I can get on this. I need this phone!
Thanks in advance!
Is your plan a pay-per-use plan or a pay-as-you-go plan? It makes a difference because smartphones cannot be used on a pay-per-use plan.
Thanks for the reply, I believe I'm pay-as-you-go. I purchased a GoPhone close to a year ago (maybe 9-10 months ago) and I took the SIM card, activated on the GoPhone first, then used it with 3 previous phones. I'm 99% postive it's pay-as-you-go but I got tired off constantly buying the plan monthly (unlimited talk&text) and setup an autorefill to automatically refill my account with the selected plan service (unlimited talk&text)
Again sincerely sorry for the double post again but I've had the biggest breakthrough all day. I accidentally clicked airplane mode when attempting to power off my Dell Streak. I then turned airplane mode back off and I went to power off and during the power off I noticed my bars go blue with service, in excitement I quickly turned my phone back on and did not have service. I then did my previous accident this time canceling the power off and my phone connected to AT&T network and I have full service, I quickly made a call to my buddy who's with me and it went through, upon trying to text him, it hangs on sending and eventually prompts that the message could not be sent please retry. I feel I'm so close! Does this new info help? Again I have some knowledge of all this and this all has just been so confusing to me.
EDIT: more info, I can receive messages but it seems I cannot reply :/
UPDATE: It seems I can get my Dell Streak to send messages by toggling airplane mode on then off, but it's only temporary and I have to repeat the process almost every other message just to get my message to send. Again this is just adding more confusion to my problems. I can't imagine why all this is working like this!
Thanks in advance once again!
-hawker
I had a similar problem, I got my unlock code from AT&T, unlocked the device (when it prompted and I had a T-Mo-USA sim inserted), it shows the number in the device identity screen, but never connects to a network. I just swapped my old Streaks motherboard to my Streak with a working screen, just to see if this would work, working on getting this motherboard unlocked too.
jmhalder said:
I had a similar problem, I got my unlock code from AT&T, unlocked the device (when it prompted and I had a T-Mo-USA sim inserted), it shows the number in the device identity screen, but never connects to a network. I just swapped my old Streaks motherboard to my Streak with a working screen, just to see if this would work, working on getting this motherboard unlocked too.
Click to expand...
Click to collapse
Am Facing same issue in India. SIM1 suddenly stopped working, but SIM1 works on other phone and SIM2 from other phone also works on Dell Streak. Its only the Dell Streak + particular SIM that is not working. What could be the issue.. Will flashing a modem help.?
Thanks
Even, i have been having this problem with my streak, posed it here few months back but of not much help. It identifies the cell provider and all, and then shows the "x" at the signal bar. While keep restarting the phone, sometimes it suddenly works for 2-3 minutes and then, goes back to frustration.
Ok so I (foolishly) bought a galaxy s4 with verizon even though I was moving overseas to Israel in two months. I made sure that the phone was world capable (like it can do cdma and gsm) and the guy at the store said it would handle foreign sims no problem. Once I arrived here I got a new sim. I figured out that it needed to be in gsm. From then on it had the service bar and confirmed it was connected to Orange. Since then I have been able to receive calls and texts, but not make them, every time I try to make a call before one ring I get a prerecorded message saying that my number cant be completed as dialed. I have tried several things already to fix this: to a cell phone repair person, to the local sim carrier where a lady tried using the sim of her own phone, customer service at verizon and samsung (who both told me to go see the other). I also did a factory reset which didnt do anything.
my phone is not rooted and is schi545 ME7. I will root if I have to, but if I dont I would prefer not to for the time being
Anyway I suspect the problem has something to do with the fact that I got the phone from verizon. Every time I start the phone I get the Verizon logo and after a minute I get a notification from the verizon set up wizard saying that I have a non verizon sim and that the sims source is unknown. I also tried disabling the verizon security and was able to make the notification go away but the problem persists.
Can someone with experience with this kind of stuff help me please? Thank you so very much:good:
Are you sim unlocked? I don't think the phone is unlocked. Talk to verizon to see if they'll unlock it.
According to verizon I am. I spoke with multiple representives from verizon and they said the phone was unlocked
medphratalon said:
According to verizon I am. I spoke with multiple representives from verizon and they said the phone was unlocked
Click to expand...
Click to collapse
Has any one told you if you have to change any apn, access point name? That may be the problem too. They can be specific to the carrier.
No, how do you configure that
medphratalon said:
No, how do you configure that
Click to expand...
Click to collapse
In system settings, network & wireless, more, mobile networks, access point name. It'll be specific to the carrier so i can't help you there.
all LTE Verizon phones after Galaxy Note 2 are factory unlocked it must be a APN issue. Try maybe to do a factory reset and as previous poster suggested do the steps he told you to change the APN or look into I think it's called HiApn in Play Store.
Also try to put it in global mode or GSM? play with the settings.
still having problems
Thanks for all the input everyone but my problem still persists
I downloaded HiApn and followed its instructions to which told me to set up 3 Apns. I noticed that only one of them can be active at the time. I tried with each one active and I still can not make phone calls. Does anyone have any other ideas?
medphratalon said:
Ok so I (foolishly) bought a galaxy s4 with verizon even though I was moving overseas to Israel in two months. I made sure that the phone was world capable (like it can do cdma and gsm) and the guy at the store said it would handle foreign sims no problem. Once I arrived here I got a new sim. I figured out that it needed to be in gsm. From then on it had the service bar and confirmed it was connected to Orange. Since then I have been able to receive calls and texts, but not make them, every time I try to make a call before one ring I get a prerecorded message saying that my number cant be completed as dialed. I have tried several things already to fix this: to a cell phone repair person, to the local sim carrier where a lady tried using the sim of her own phone, customer service at verizon and samsung (who both told me to go see the other). I also did a factory reset which didnt do anything.
my phone is not rooted and is schi545 ME7. I will root if I have to, but if I dont I would prefer not to for the time being
Anyway I suspect the problem has something to do with the fact that I got the phone from verizon. Every time I start the phone I get the Verizon logo and after a minute I get a notification from the verizon set up wizard saying that I have a non verizon sim and that the sims source is unknown. I also tried disabling the verizon security and was able to make the notification go away but the problem persists.
Can someone with experience with this kind of stuff help me please? Thank you so very much:good:
Click to expand...
Click to collapse
Go to Setting, call setting, disable the prefix international. I have done the same for using Verizon S4 in Indonesia.
Mine was not unlocked either, although I knew this before buying. This is a guide I tried (without success) to unlock it on my own.
Like the last poster, I reside in Indonesia, but I was never with Verizon. I rooted mine and have had no problems since.
Ok so I went to call settings and the closest I found was assisted dialing for international calls and the option to turn it on or off. I played with that for a bit and it didnt work.
I also tried the code and it said connection problem or invalid code
during my fiddling I came upon an app that showed promise of fixing my problem if I had adb shell. Does anyone have a good place to get that? I tried a few that didnt work out for me. There was another that showed promise but it wouldnt send a package no matter what I try
Thanks
If you want ADB, you need to download Android SDK and have Java Runtime Environment also installed. Then, it is just a matter of typing in "adb" into the command prompt of Windows.
Is there a serious conflict for you not rooting the device? The true benefit of doing this is to get SIM cards from anywhere to work, and to allow certain apps to work. Rooting is simply a matter of bypassing security parameters. As long as you follow instructions strictly, you won't have an issue using the phone as it should be used.
yea I suppose I could try to root it. Im just not great at that stuff and am worried about messing up my phone permanately
medphratalon said:
yea I suppose I could try to root it. Im just not great at that stuff and am worried about messing up my phone permanately
Click to expand...
Click to collapse
You don't need to root. You need to sim unlock. Get a hold of att international chat and adj them for an unlock code.
Hey guys thanks for all the help but I figured out that it was just a bad sim all along and that the first school screwed me over
But everything works now
Hello Everyone.
I am stumped on this issue. There doesn't seem to be any solutions for me. Here is What's happening, then I will tell you what I know..
Originally an ATT watch. SM-R750A
The IMEI is perfect. Not black listed at all. (Verified with ATT,SAMSUNG, and TMOBILE)
It is unlocked by ATT - I received the code and used it with the Tmobile Sim card inside when prompted. Success.
ATT Sim cards work perfectly,and with 4G!! When my Tmobile Sim goes in there, it only allows Emergency calls.
The APN settings are automatically populated. Verified to be correct with Tmobile. Basically, everything is fine on their end..
I am getting the run around from all 3 sources. They point the finger at each other.
Example:
Tmobile :"ATT did not unlock it completely, call them and ask for it to be fully unlocked."
ATT: "Once we gave you the code, our hands are tied. Call samsung, they may be able to complete your request.."
Samsung: "This is a service/network issue. Contact who ever your sim card has service with.."
Please help me, I have tried everything I can think of.
I researched all over the internet.. There are no working solutions anywhere!!!
I even Oden flashed the Official Firmware from ATT to Tmobile, so now my Model # is SM-R750T. I get the same errors. Att sim cards still work perfectly.
:crying:
I added photos of a menu I found on the device.. I dont know what this means..
I can draw conclusions, but I still need help..
Also, I have had the Tmobile Sim card replaced twice..
If someone could help find a solution, this will help a LOT people!
Thank You AHEAD of time.
did you flash the entire firmware package?
I only flashed official firmware from ATT to TMOBILE.. That was all. If there are further steps please let me know.
I stopped at the firmware install because I thought anything extra would have just been for customizing themes, etc..
animegamemaster said:
Hello Everyone.
I am stumped on this issue. There doesn't seem to be any solutions for me. Here is What's happening, then I will tell you what I know..
Originally an ATT watch. SM-R750A
The IMEI is perfect. Not black listed at all. (Verified with ATT,SAMSUNG, and TMOBILE)
It is unlocked by ATT - I received the code and used it with the Tmobile Sim card inside when prompted. Success.
ATT Sim cards work perfectly,and with 4G!! When my Tmobile Sim goes in there, it only allows Emergency calls.
The APN settings are automatically populated. Verified to be correct with Tmobile. Basically, everything is fine on their end..
I am getting the run around from all 3 sources. They point the finger at each other.
Example:
Tmobile :"ATT did not unlock it completely, call them and ask for it to be fully unlocked."
ATT: "Once we gave you the code, our hands are tied. Call samsung, they may be able to complete your request.."
Samsung: "This is a service/network issue. Contact who ever your sim card has service with.."
Please help me, I have tried everything I can think of.
I researched all over the internet.. There are no working solutions anywhere!!!
I even Oden flashed the Official Firmware from ATT to Tmobile, so now my Model # is SM-R750T. I get the same errors. Att sim cards still work perfectly.
:crying:
I added photos of a menu I found on the device.. I dont know what this means..
I can draw conclusions, but I still need help..
Also, I have had the Tmobile Sim card replaced twice..
If someone could help find a solution, this will help a LOT people!
Thank You AHEAD of time.
Click to expand...
Click to collapse
Tmobile :"ATT did not unlock it completely, call them and ask for it to be fully unlocked."
From my understanding, there are no levels of unlock permissions. Once a device is unlocked, it's done on all levels and access.
It is unlocked by ATT - I received the code and used it with the Tmobile Sim card inside when prompted. Success.
The unlock code needs to be entered on device while connected to the ATT network...not TM's. My initial suggestion is kindly call back ATT and with the correct IMEI/ATT Sim inserted, enter unlock code again. You may need to flash back to xxxA first.
My thought here is the phone isn't unlocked according to ATT's server's Device ID data...when you reestablished connection with ATT, it locked the device again.
[Q]
You said that you got the unlock code from ATT, with TM Sim inserted, and it was a success....
Why did you go back to the ATT Sim again if you had it working?
animegamemaster said:
Hello Everyone.
I am stumped on this issue. There doesn't seem to be any solutions for me. Here is What's happening, then I will tell you what I know..
Originally an ATT watch. SM-R750A
The IMEI is perfect. Not black listed at all. (Verified with ATT,SAMSUNG, and TMOBILE)
It is unlocked by ATT - I received the code and used it with the Tmobile Sim card inside when prompted. Success.
ATT Sim cards work perfectly,and with 4G!! When my Tmobile Sim goes in there, it only allows Emergency calls.
The APN settings are automatically populated. Verified to be correct with Tmobile. Basically, everything is fine on their end..
I am getting the run around from all 3 sources. They point the finger at each other.
Example:
Tmobile :"ATT did not unlock it completely, call them and ask for it to be fully unlocked."
ATT: "Once we gave you the code, our hands are tied. Call samsung, they may be able to complete your request.."
Samsung: "This is a service/network issue. Contact who ever your sim card has service with.."
Please help me, I have tried everything I can think of.
I researched all over the internet.. There are no working solutions anywhere!!!
I even Oden flashed the Official Firmware from ATT to Tmobile, so now my Model # is SM-R750T. I get the same errors. Att sim cards still work perfectly.
:crying:
I added photos of a menu I found on the device.. I dont know what this means..
I can draw conclusions, but I still need help..
Also, I have had the Tmobile Sim card replaced twice..
If someone could help find a solution, this will help a LOT people!
Thank You AHEAD of time.
Click to expand...
Click to collapse
Try this. Go to phone dialer, type in *#2263# , dont hit call , just wait for the menu. When it comes up, select GSM band preference and if its an option, choose GSM 1800. Then swipe down to exit.
Sent from my SAMSUNG-SM-N910A using XDA Free mobile app
mghtymse007 said:
Tmobile :"ATT did not unlock it completely, call them and ask for it to be fully unlocked."
From my understanding, there are no levels of unlock permissions. Once a device is unlocked, it's done on all levels and access.
It is unlocked by ATT - I received the code and used it with the Tmobile Sim card inside when prompted. Success.
The unlock code needs to be entered on device while connected to the ATT network...not TM's. My initial suggestion is kindly call back ATT and with the correct IMEI/ATT Sim inserted, enter unlock code again. You may need to flash back to xxxA first.
My thought here is the phone isn't unlocked according to ATT's server's Device ID data...when you reestablished connection with ATT, it locked the device again.
[Q]
You said that you got the unlock code from ATT, with TM Sim inserted, and it was a success....
Why did you go back to the ATT Sim again if you had it working?
Click to expand...
Click to collapse
The unlock code worked. I was not prompted to enter another unlock code. I received success notification. I immediately got the error code that you see in the pictures. Could not dial out. So i went to ATT store for some hands on troubleshooting. But I will try to use the sim card idea you mentioned. I will come back with an update.
vacortina said:
Try this. Go to phone dialer, type in *#2263# , dont hit call , just wait for the menu. When it comes up, select GSM band preference and if its an option, choose GSM 1800. Then swipe down to exit.
Sent from my SAMSUNG-SM-N910A using XDA Free mobile app
Click to expand...
Click to collapse
This is a 'no-go' as well.. I will flash my firmware back to ATT and try it again.
Edit:
No, this did not work as well..
animegamemaster said:
The unlock code worked. I was not prompted to enter another unlock code. I received success notification. I immediately got the error code that you see in the pictures. Could not dial out. So i went to ATT store for some hands on troubleshooting. But I will try to use the sim card idea you mentioned. I will come back with an update.
Click to expand...
Click to collapse
The same here. I'm from Vietnam. My boss from USA visited Vietnam office and gifted me a T-mobile Gear S with the unlock code from T-mobile. Before unlocking the network, i upgrade it with the latest firmware from T-mobile (R750TUVU1A07). I then inserted a VN carrier SIM and did follow T-mobile guide as below:
1.Insert a Non-T-Mobile SIM & turn the Gear S ON.
2.The Gear S will automatically prompt you to enter the unlock code.
3.Tap in the unlock code provided by T-Mobile and click OK.
Note: The device should display code accepted
Click to expand...
Click to collapse
After i receive the successful message, i still cant make call or send message. It keep saying that "Mobile network is not available". I tried with 3 nano sim cards from 3 biggest carriers in VN but there is no luck. (These sim cards work well on the iPhone 5).
BTW, the GPS also didn't work, even before or after unlocking with the code. It keep saying "GPS signal too weak. Please connect the Gear to mobile device via Bluetooth" (or something like that).
snowinjune said:
The same here. I'm from Vietnam. My boss from USA visited Vietnam office and gifted me a T-mobile Gear S with the unlock code from T-mobile. Before unlocking the network, i upgrade it with the latest firmware from T-mobile (R750TUVU1A07). I then inserted a VN carrier SIM and did follow T-mobile guide as below:
After i receive the successful message, i still cant make call or send message. It keep saying that "Mobile network is not available". I tried with 3 nano sim cards from 3 biggest carriers in VN but there is no luck. (These sim cards work well on the iPhone 5).
BTW, the GPS also didn't work, even before or after unlocking with the code. It keep saying "GPS signal too weak. Please connect the Gear to mobile device via Bluetooth" (or something like that).
Click to expand...
Click to collapse
You most likely will not be able to use a North American S outside the US. It has nothing to do with the software...the frequency bands are different and hardcoded. You may want to check and see what bands are used by the providers in VN for cellular ie: 2G, 3G, etc and compare those to what US/Sprint uses.
I have the same issues with the GPS. Even when I'm outside, in an open area I can't even get the weather app to update. Not sure how many people have this issue, but it doesn't seem to be a topic of discussion on XDA.
snowinjune said:
The same here. I'm from Vietnam. My boss from USA visited Vietnam office and gifted me a T-mobile Gear S with the unlock code from T-mobile. Before unlocking the network, i upgrade it with the latest firmware from T-mobile (R750TUVU1A07). I then inserted a VN carrier SIM and did follow T-mobile guide as below:
After i receive the successful message, i still cant make call or send message. It keep saying that "Mobile network is not available". I tried with 3 nano sim cards from 3 biggest carriers in VN but there is no luck. (These sim cards work well on the iPhone 5).
BTW, the GPS also didn't work, even before or after unlocking with the code. It keep saying "GPS signal too weak. Please connect the Gear to mobile device via Bluetooth" (or something like that).
Click to expand...
Click to collapse
---------- Post added at 02:15 PM ---------- Previous post was at 02:12 PM ----------
animegamemaster said:
This is a 'no-go' as well.. I will flash my firmware back to ATT and try it again.
Edit:
No, this did not work as well..
Click to expand...
Click to collapse
Have you tried rooting?
http://forum.xda-developers.com/showthread.php?t=2977581
Thanks to cipherswitch
This is from "CELLUNLOCKER" where I got my unlock code...before it was free...lol....... When I click on the t mobile for network....I get "registered to networkk" popup with my ATT GS. When I call a number I get the tmobile cust servc help line...... since I am not a tmobile cust.
I cannot remember which method I used....but I can go with att or tmobile sims with no issues. Right now I have H20 as my carrier, on the ATT network...but at least I know I can go to the Tmobile network or carriers anytime
How to enter unlock codes on all Samsung models
Different phones have different Unlock Code Input Instructions, Try the following Instructions in order:
Note: Non Accepted Simcard is any simcard not from the original provider
Method #1 Insert a Non accepted simcard in your phone and power on. Once finished loading your phone will ask you to enter a code, enter the Unlock Code
OR
Method #2 (NOT applicable for newer Samsung phones, ie. Galaxy S3, S4, S5, Note 2, Note 3, etc)
Go to the dial screen on your phone as if you are going to make a call and press: #7465625*638*UNLOCKCODE# (8 digit unlock code)
OR
Method #3 (NOT applicable for newer Samsung phones, ie. Galaxy S3, S4, S5, Note 2, Note 3, etc)
Go to the dial screen on your phone as if you are going to make a call and press: #0111*UNLOCKCODE# (8 digit unlock code)
OR
Method #4 (NOT applicable for newer Samsung phones, ie. Galaxy S3, S4, S5, Note 2, Note 3, etc)
Go to the dial screen on your phone as if you are going to make a call and press #7465625*638*# Once prompted for code, enter the 8 digit Unlock Code.
When this method is used for newer Samsung phones, it will say "unsuccessful" regardless of the phone being unlocked or not.
Phone Not Allowed MM#6 Tmobile- A clue to problem?
I also have the same problem...it is frustrating.
i have an unlocked AT&T Gear S ( unlocked thru one of the unlock ebay sites. it seemed to go well, and worked)
i setup account with Tmobile, and it worked, i have had it about 2 months, all OK, until..
i took out SIM to test with my unlocked IPHONE 6+, (i have been thinking of switching all my phones to Tmobile) it also worked OK,
Then i swicthed it back into the Gear S, and the trouble started (unless it was a conincidence),
'Phone not allowed MM#6', it tried everything.
1. reset Gear
2.rebooted thru the gear boot menu
-i called Tmobile, they did not have answer,m they asked me to try a new SIM, which i did online and updated account with new SIM,
same problem.
3.Tmo said maybe not complety unlocked to contact AT&T but i doubted this,
4. I tried a freinds SIM from his Iphone 6+ (on Tmo) it worked great in my Gear Sm and my 'unlocked Ipphone 6'
5. i tried my Gear S SIM in my Iphone, message poped up 'Phone not allowed' (this time no MM#6)
6. called Tmo again (maybe 3rd time) suggested another new SIM card, they everything on there end looks fine, they checked imei, sim card etc, all OK.
i told them from what i have read the forums mentioned a network problem, not a phone problem.
They connected with Samsung, they said they can try reflashing the Gear S, if i send it in to them,
7. i called Tmo again, and i spoke one rep who , GAVE ME A CLUE TO PROBLEM.. he found a note concerning the Gear S,
it said if the user puts the Gear S SIM cards (wiith the 'wearable plan') into another phone, it will block the account until the user reinstalls SIM into Gear S.
8. if this the problem, iit is not reseting itself when SIM is back in Gear S.
9. Not sure what to do next.
the last Tmo rep told to go into Tmo store, and they will try another new SIM, and ask them to try new SIM and my in anoother Gear S, but it seems many tmo stores dont have Gear S on hand, only display it am checking.
10. One idea may be to close the whole account and open new account for the Gear S.
did anybody have luck with this problem?
perdikoylis said:
I also have the same problem...it is frustrating.
i have an unlocked AT&T Gear S ( unlocked thru one of the unlock ebay sites. it seemed to go well, and worked)
i setup account with Tmobile, and it worked, i have had it about 2 months, all OK, until..
i took out SIM to test with my unlocked IPHONE 6+, (i have been thinking of switching all my phones to Tmobile) it also worked OK,
Then i swicthed it back into the Gear S, and the trouble started (unless it was a conincidence),
'Phone not allowed MM#6', it tried everything.
1. reset Gear
2.rebooted thru the gear boot menu
-i called Tmobile, they did not have answer,m they asked me to try a new SIM, which i did online and updated account with new SIM,
same problem.
3.Tmo said maybe not complety unlocked to contact AT&T but i doubted this,
4. I tried a freinds SIM from his Iphone 6+ (on Tmo) it worked great in my Gear Sm and my 'unlocked Ipphone 6'
5. i tried my Gear S SIM in my Iphone, message poped up 'Phone not allowed' (this time no MM#6)
6. called Tmo again (maybe 3rd time) suggested another new SIM card, they everything on there end looks fine, they checked imei, sim card etc, all OK.
i told them from what i have read the forums mentioned a network problem, not a phone problem.
They connected with Samsung, they said they can try reflashing the Gear S, if i send it in to them,
7. i called Tmo again, and i spoke one rep who , GAVE ME A CLUE TO PROBLEM.. he found a note concerning the Gear S,
it said if the user puts the Gear S SIM cards (wiith the 'wearable plan') into another phone, it will block the account until the user reinstalls SIM into Gear S.
8. if this the problem, iit is not reseting itself when SIM is back in Gear S.
9. Not sure what to do next.
the last Tmo rep told to go into Tmo store, and they will try another new SIM, and ask them to try new SIM and my in anoother Gear S, but it seems many tmo stores dont have Gear S on hand, only display it am checking.
10. One idea may be to close the whole account and open new account for the Gear S.
did anybody have luck with this problem?
Click to expand...
Click to collapse
Call tmo back and have them make sure you have the right data plan I had the same problem and mine was on a tablet data plan not mobile/watch plan
I am experiencing a similar issue with TMobile. My thread is in here, http://forum.xda-developers.com/gear-s/help/gear-s-longer-able-to-register-tmobiles-t3040635
I have the factory unlocked international version, SM-R750W, and several people here said it wouldn't work. It worked perfectly for a day, then nothing. New SIM, it worked perfectly again for maybe 5 minutes.
HagbardCelineII said:
I am experiencing a similar issue with TMobile. My thread is in here, http://forum.xda-developers.com/gear-s/help/gear-s-longer-able-to-register-tmobiles-t3040635
I have the factory unlocked international version, SM-R750W, and several people here said it wouldn't work. It worked perfectly for a day, then nothing. New SIM, it worked perfectly again for maybe 5 minutes.
Click to expand...
Click to collapse
Still no luck, but maybe a couple more clues;
1. As the tech support advised, I went to a Tmo store, and they swapped the nano sim , no help.
2. I put in a sim from my friends tmo iPhone. It seemed great.
3. I called tech support back, they escalated problem to the engineering dept,
Said it may take 2 days to hear back...... So far no luck, please let me know if you have better results.
(I did check the plan online and with support to be sure it was correct.- the wearable / watch plan)
I feel it has something to do with there network 'rejecting' my imeo, but support checked that several times, as said it is correct.
perdikoylis said:
Still no luck, but maybe a couple more clues;
1. As the tech support advised, I went to a Tmo store, and they swapped the nano sim , no help.
2. I put in a sim from my friends tmo iPhone. It seemed great.
3. I called tech support back, they escalated problem to the engineering dept,
Said it may take 2 days to hear back...... So far no luck, please let me know if you have better results.
(I did check the plan online and with support to be sure it was correct.- the wearable / watch plan)
I feel it has something to do with there network 'rejecting' my imeo, but support checked that several times, as said it is correct.
Click to expand...
Click to collapse
They escalated my situation as soon as I called them on Tuesday and told me 3 days. Nothing yet.
Have you used the Tmobile IMEI check? http://www.t-mobile.com/verifyIMEI.aspx
I just tried it and it doesn't recognize my IMEI....But if that was going to be a problem, shouldn't that have meant it would never work? I can't think of any reason it would work for a day before they shut it off.
I had same result "did not recognize" with there Imei checker, further, the support reps checked several times and said it is Ok, My gear s is an unlocked AT&T, it did work for the first 2 months (until I removed sim to test in my iPhone ( I was considering switching all my phones to Tmo) Maybe coincidence? + But with a friends sim (from his iPhone ) it worked immediately , it even populated the Apn etc settings, but i did not leave on more than 1-2 minutes to test.
When I put my sim back in, it does not register, it does even show phone number, says:
"Phone not allowed MM#6" and emergency calls only.
I had this same issue come up. The way I solved it was to close out the account for my phone number tied to the watch wearable plan. And then I created a new phone account for the wearable plan with a new number. And got a new sim card from T-Mobile at the time of creating the new wearable plan / number. It seems that the phone number that was previously tied to my galaxy gear s was not blacklisted, but the services were limited on it because I had taken the sim card out of the gear s watch and put it into a cell phone to test if there was service on it. So that flagged the wearable phone number account like I was trying to steal data/phone service from T-Mobile by using the only $15 / month plan on an actual phone. Like said above, the services are supposed to be restored once you put the sim back into the watch, but there is a bug with T-Mobile's service in doing so. So in the end, I closed out the "flagged" account, opened a new account and will never put the sim card into a phone again in the future.
same the issue
snowinjune said:
The same here. I'm from Vietnam. My boss from USA visited Vietnam office and gifted me a T-mobile Gear S with the unlock code from T-mobile. Before unlocking the network, i upgrade it with the latest firmware from T-mobile (R750TUVU1A07). I then inserted a VN carrier SIM and did follow T-mobile guide as below:
After i receive the successful message, i still cant make call or send message. It keep saying that "Mobile network is not available". I tried with 3 nano sim cards from 3 biggest carriers in VN but there is no luck. (These sim cards work well on the iPhone 5).
BTW, the GPS also didn't work, even before or after unlocking with the code. It keep saying "GPS signal too weak. Please connect the Gear to mobile device via Bluetooth" (or something like that).
Click to expand...
Click to collapse
Hi...I have same the issue...now are you solve? You can help me this issue?...thank you
A good looking digital watch
zztoine said:
Hi...I have same the issue...now are you solve? You can help me this issue?...thank you
Click to expand...
Click to collapse
No, i follow this guide to try some features of the Gear S. But my phone become sluggish, and the GPS still not work.
http://forum.xda-developers.com/gea...ll-gear-manager-connect-t2934307/post60592795
So, right now, the Gear S is just a digital watch to me, ha ha.
The error is specifically a sim/network error unfortunately and more importantly this;
9 out of 10 times MM6 error means the phone has been reported lost/stolen and the IMEI has been network blocked.
Here are a few options that could be causing most of the issues I have read;
At&t is NOT open and a fan of allowing devices outside their network. Therefore its possible your device is literally reported as lost/and or locked to at&t and they dont want it on T-Mobile. And your best bet is to raise hell threating an investigation by the FCC.
At&t re-locked your device when att sim is put in.