I found a thread about HDMI mirroring from DS 5;
As google translates;
[Evaluation] of the DELL STREAK MINI5 [HDMI】 update! Please pay attention! Up to support the use of skills and test
first to HDMI introduction of a period of official products: HDMI devices play video 2011/07/09 By, Via: Powered original player on the HDMI device video 1 will 30-pin connector of the bottom of the device is inserted into the 30-pin dock connector. 2 Use the HDMI data cable equipment with HDMI devices (such as HDMI monitor or TV) connected. 3 Touch Application "(application) button → Photos | & Videos (photo & video). 4 Touch video thumbnails, start the video. 5 device screen will display the Video out (video output) asks you to confirm. Touch Ye, s (is) in the connected HDMI device to play the video. If you do not want to play the video on the device, the Touch No (No). 6 To switch the device screen and HDMI display screen playback, touch the "Menu" (menu) button → Change video out (to change the screen output). 7 To control the playback, use the controls in the device screen:? Touch of a button to pause playback, the touch of a button you can continue playing. ? Touch or drag the yellow playback progress bar to rewind or fast forward the video. Note: The device supports HDMI output WMV9/MPEG-4/H264/H263 video files. Note: HDMI output resolution to 720p.
Original the Dell MINI5 base, $ 59 from the United States buy, buy address: http://www.ebay.com/itm/DELL-STREAK-TABLET-HOME-AV-HDMI-DOCK-KIT-ORIGINAL-NEW
written -/330621384311 base, MADE IN CHINA, work did not have to say, Chinese exports to the U.S. things, the quality often gray ash often good, then I buy it back. . And helpless. Domestic Dell official call, there is a clear domestic test ROM is 15881, the official ROM, you can connect to the TV, but must use the ROM comes with pictures and video player can choose to enter "switch to HDMI " connection so far, want to play something of special format or network video software can not play, some users said, MINI5 This feature is tasteless, there are not as good as 200 yuan of MP4, but I believe through our efforts, or have the opportunity to be resolved. . Is still in testing phase, the idea is as follows: an extraction can be used to switch the HDMI built-in player software to the 2.3 version of the ROM, the CM7 or DSC, two relatively stable some of the 2.3 version to see if success to find other players Andrews supports video output to HDMI devices, or network player. 3, other more effective measures to HDMI is no longer tasteless. . 2012.3.18.22:48 test software: real the HDMI
Original link to thread,apk and HDMI cable;
http://bbs.zhangku.com/thread-80580-1-1.html
Where wa the .apk download link? I couldn't find it...
Hello, everyone.
OK, I finally got time to test the Android stick mini PC that I bought in Shenzhen, Guangdong Province, China
The device is model T-001, by AuxTek (I dont think it's a registered brand name).
MODEL: T0001
System = Android 4.1.1
CPU - RK3066 Dual CPU
2GB DDR3 RAM (actual available 1.45GB)
Internal 8GB memory (actual available 4.83GB)
WIFI capable
BLUETOOTH capable
HDMI-VIDEO OUTPUT
2.4GB Wireless Mouse _ Keyboard (It's actually like holding a LASER POINTER to point and click the APPs on the screen).
*See the attachment photos about the packing and the accessories.
OK, the HDMI connecting cable is loosen, so if I move the mini pc, the screen may black out.
and also, I dont trust the quality of the power supply (5V-2A).
I bought the HDMI adaptor and a new power supply for it (one may also use a Google Nexus 7 or iPad charger for it).
*Next post about the first thing that I do on the device...ROOTING it! (it is a must have software/app)
OK, Part 2.
About ROOTING the device.
I use "Tencent Mobile Manager"
(see photo below for download the software, and install it on the PC).
Note:
(1) In order to communicate with the PC, one can connect the mini pc to the PC by USB cable using the OTG port.
*This does not make the mini pc as a "storage device" on the PC. It simply can communicate with the Tencent Mobile Manager only!
(2) According to the instruction menu, in order to become a "storage device" when connecting to the PC, one must connect the mini pc to the home PC by using the USB port that
connects the Remote Control/Keyboard *the bottom USB port.
*However, the package does not have this cable. So I have not tried out this function yet!
(3) According to the instruction menu, there is a reset button on the left side of the mini pc. Pressing it with a pin is supposed to go to recover menu. But I have not tried this yet!
OK, after the home PC has installed Tencent Mobile Manager, it will automatically find the mini pc and a menu will pop up.
>Click the one-click manager button, and it will ROOT and manage the device to best performance (such as cleaning caches and unwanted files) *optimization!
When Rooting the mini pc, it also will install the Tencent Mobile Management app in the mini pc.
**after the success ROOT, you can click this app and learn that the phone is ROOT!!
Also, I installed "Titanium BackUp" and "Root File Manager" to test the device if it is ROOT. and It is!!!
This Tencent Mobile Manager is a must have program (and app) on the PC and the mini pc for communication and manage the device.
>It can manage the files within the device (between internal memory and the SD card) easily!
>It helps to scan all downloads and access files during the use of the mini pc! (and it optimize the device).
>It has its own app market function (that's including finding the Adobe Flash apk!)
>It has its own movie market to download full movie files into the device!!
OK, turning on the device, and first go to "About the device" to check the firmware and hardware version/software version.
*see the attachment photo in the last post.
The device is displayed just like any other Android device.
The bottom menu bar reads
(1) Go back
(2) Home menu
(3) Apps that are opened and are running in the background
(4) "Screenshot"
(5) Volume down
(6) Volume up
And this is Android 4.1.1
So, when one pull the bottom menu bar up, it opens the Google Search menu!
OK, you can check the attachment photos to see what apps I have installed and run in this mini pc.
Basically, it is used as an entertainment center for my parents. They can watch all the Chinese TV dramas and movies,
and access all China cable TV networks from this thing!
**The test is done on my Panasonic 50" plasma TV. So I think if it works on a large screen TV, anything that's less than 50" should be ok.
**The device is set at 720P by default, The wholesaler suggests to me to keep it at 720P even the 1080P option is available in the HDMI output setting. So I have not changed this.
**The device is in good temperature during the usage time (watching steaming movies from networks in China for awhile).
**I have also used a 2GB SD card to store music, movie (American Horror Story Season 1), and photos. and they all works out fine!
(The mini pc supports 32GB SD card)
The device has an app called "explorers", which is to access and edit the files inside the device.
>The device can use OTG port to connect an "USB memory stick" if a SD card is not present.
**can only choose to use either a SD card (via SD Cad slot) or a USB memory stick (via OTG port). CANNOT USE BOTH AT THE SAME TIME!
First, I have to install a chinese input keyboard (CedIME app) so that I can type chinese on the mini pc during search and internet browsing.
>The wholesale tells me there wont be any firmware updates in the future. But I have tested the System Update and it's running anyway. haha.
*dont know if I should try to flash the ROM myself in the future, as I have no idea which one supports this mini pc. haha.
OK, I have tested many available online video apps, and this one is really good.
*have very new movie and TV episodes available!!
*the steaming is very smooth, not much lag. (my wi-fi connection signal is already just fair)
In the end, I tested it with a Japanese pervert superman movie "Hentai Kamen"
CONCLUSION:
Pros:
(1)The operating temperature is good. Just mild warm.
(2)Speed is good. The remote control pointer sometimes lag, but overall ok. It needs just few minutes to get used to it.
(3)The Remote Control with Keyboard is a must have device to go with this mini pc!
(4)At 720P, it is already very good graphic quality in a good balance between "visual quality" and "smooth steaming"
(5)Tiny device, easy to fit just next to the TV.
(6)ROOTing this mini pc is necessary, and the Tencent Mobile Manager is a recommended companion to go with it! Really useful!!
Cons:
(1)Some apps that are installed via apk file or other non-Play Store download, it has to be uninstalled through "Settings->Apps".
And after every uninstall, it will reboot the device. And after every reboot, the Wi-Fi has to be turn OFF and then turn ON to search the
Wi-Fi connection correctly again!!
(2)The USB cable, HDMI cable, and the Power charger (5V-2A) are below average quality.
*I changed them to use my own HDMI adaptor, my own HDMI cable, and my own USB cables (Nokia and Sony), and my own Power Charger.
(3)The package does not come with the USB cable that connect the mini pc to Home PC as an externam storage device. I have to buy a new cable to test this function (which I have not done).
oh, the size of it, in comparing to a Nokia 920
I know this thread is old,
I have an auxtek T004, allwinner A10s cpu running android.
I wonder if is there a way to run OpenElec on it, as Xbmc/Kodi is not booting (crashes after "preparing for first boot").
Thanks in advance.
Hello all! My first attempt at any type of guide or help, so give me pointers if you notice a better way to go about this than what's here.
This was done by me on my Ultra that broke, but I would imagine the same works for any other device that has a Snapdragon 800, and probably earlier chipsets as well. SPMC and XBMC have documentation about the supported hardware.
Doesn't it suck when you crack the screen on your baby and she no longer responds to touch input? We've probably all been there with one device or another. But don't let that busted phone gather dust, turn it into a full fledged media center! These quad core beasts can do so much more than the phones of a few years ago. I take no credit for anything here, as I'm just passing along my experience so others can make use of a disabled phone.
I have used Plex, Chromecast, etc, but no combination of those gives me the control of XBMC, and the ability to play mostly any codecs without the need for transcoding.
A few things before I get into the steps:
1. I started with a rooted phone, but you don't necessarily need one. It just helps later on if you want more control over the device functions.
2. I recommend using the most up to date firmware possible, I am on 4.4.4 myself, using this rom here:
http://forum.xda-developers.com/showthread.php?t=2800414
3. You'll want a usb OTG cable like the one I used here, along with a cheapo wired usb mouse so you can control the phone until it is set up to work with a remote.
http://www.amazon.com/gp/product/B00871Q5PI/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
4. You'll also need an MHL adapter. I used this one here:
http://www.amazon.com/gp/product/B00KPXI4S2/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
5. You'll need wifi, assuming you have moved the sim to your next device.
6. You will want some form of controlling XBMC remotely. I use Yatse for Android, installed on my replacement phone and it's a godsend.
https://play.google.com/store/apps/details?id=org.leetzone.android.yatsewidgetfree&hl
Here we go.
1. Clean that busted phone up. Reset to factory settings, flash a new rom, OR just remove any non-essential apps. I only have my phone signed into Google so I can access the Play store, which you will want to do as well.
2. Install this if you are rooted. It will allow the phone to disable the screen when the MHL adapter is plugged in, saving battery and keeping it nice and dark around your TV. The wizard should guide you through a fairly simple set up. What you are looking for is for the app to disable/suspend/standby the screen when it detects MHL.
https://play.google.com/store/apps/details?id=com.nkahoang.screenstandby&hl
3. Install SPMC. This is a forked version of XBMC for Android, and frankly, it's better suited for this application. It has more features, and takes better advantage of the hardware.
https://play.google.com/store/apps/details?id=com.semperpax.spmc
4. After installing SPMC, you can use it as a launcher, meaning the phone will boot directly into SPMC. Just press home and you'll be given the option.
5. Launch SMPC, go into Settings-Services-Webserver and check Allow control of XBMC via HTTP.
6. At this point, you can now control SPMC with Yatse or another similar XBMC remote app on another device. Depending on your situation, you may still want that mouse to do a few more things before you connect to the TV.
Options Options Options
I use XBMC in my living room on a dedicated PC. My media resides on a NAS, wired via gigabit ethernet to an AC wireless router. Since I wanted to use this broken phone as a sort of satellite system in the bedroom, I set up a MySQL server on the same NAS. It can be daunting, but XBMC provides great documentation and this method makes getting your media onto the phone very easy.
http://kodi.wiki/view/MySQL
If you do not have another XBMC or do not wish to share the library between devices, skip this section.
1. If you have another instance of XBMC, give this a serious look, as both the library and the playback status will be synced among all devices. You can stop in one room and resume in another.
2. Running the current version of SPMC, and XBMC 13.2, I had no issues with MySQL, despite the warning to use the same build date.
3. If you have this type of setup, all you need to do is copy the advancedsettings.xml file you created from your original XBMC install, and paste it into the userdata folder deep inside the SPMC file structure. This is usually found inside sdcard/Android/data
4. Once you do this, launch SPMC and your existing library will be there.
5. I have not tried this, since I went through the trouble to set up MySQL before, but you can alternatively use Media Browser 3 to serve up your library, and it does appear
to be easier to set up. Download the XBMB3C plugin inside XBMC/SPMC to allow for this.
http://mediabrowser.tv/download/#server
Add Media
Alternatively, you can navigate to videos inside SPMC, select files, and then choose Add Source to add your media from wherever to your new library. There is lots of documentation over at the official XBMC site, so go there if this is your first foray into this type of thing.
I've found that I just have to turn the phone on when I walk into the bedroom, and it will boot directly into SPMC. From that point I can use Yatse on a different device to control the media center. When I am done watching content, the shutdown option inside Yatse will shut the phone off, and it just goes into a powered down charging state.
Mostly everything should play after the install, but you may need or want to adjust some settings inside SPMC/XBMC. Again, look to the official XBMC wiki for help if you need it.
If you're rooted, you can probably do without the USB OTG cable. You could use ADB to install packages and the shell (or a wrapper like this — worked well for me a few months back) to control the screen. This might also be useful if your screen is dead.
There is a new specific xbmc for android that comes preconfigured with the most important repositories for those that really don't want to dabble with all of that kind of stuff. Just install and all the main plugins are automatically installed for you. You can find it here http://www.tvaddons.ag/tvmc-android/
Is TVMC anything more than XBMC 13.2 with preconfigured settings? Seems redundant slightly because SPMC (version 13.3.2) actually contains fixes to XBMC 13.2 to enable hardware acceleration on more devices. With the Z Ultra specifically, under XBMC 13.2 official, even though hardware acceleration was enabled in the settings, it was not working. SPMC is built by official XBMC team members and contains "fixes" that were left out of the official spin for whatever reason. The settings are also mostly preconfigured, at least the defaults are different than regular XBMC, and for me at least, everything worked right away.
What are the possibilities for a phone that does not support MHL? (Oppo Find 5) I had the same idea after I broke my screen, but I am not sure now what to do. A mediacenter seemed great to me. A webserver is possible too, but I don't like how it won't use it's media capabilities anymore.
The device supports wireless screen (Miracast?) but I don't think that works great and I can't get it to work really.
Well, Android Lollipop will support Chromecast Mirroring, so if you are able to find a rom for that device when Lollipop makes its way around, that would work. There seems to be a good amount of development for that phone on XDA, so you might just need to wait it out a bit.
HaTeNL said:
What are the possibilities for a phone that does not support MHL? (Oppo Find 5) I had the same idea after I broke my screen, but I am not sure now what to do. A mediacenter seemed great to me. A webserver is possible too, but I don't like how it won't use it's media capabilities anymore.
The device supports wireless screen (Miracast?) but I don't think that works great and I can't get it to work really.
Click to expand...
Click to collapse
mailme45 said:
Well, Android Lollipop will support Chromecast Mirroring, so if you are able to find a rom for that device when Lollipop makes its way around, that would work. There seems to be a good amount of development for that phone on XDA, so you might just need to wait it out a bit.
Click to expand...
Click to collapse
This may be worth a look if you are interested in chromecast mirroring.
http://forum.xda-developers.com/har...experimental-enable-mirroring-device-t2812193
mailme45 said:
Hello all! My first attempt at any type of guide or help, so give me pointers if you notice a better way to go about this than what's here.
This was done by me on my Ultra that broke, but I would imagine the same works for any other device that has a Snapdragon 800, and probably earlier chipsets as well. SPMC and XBMC have documentation about the supported hardware.
Doesn't it suck when you crack the screen on your baby and she no longer responds to touch input? We've probably all been there with one device or another. But don't let that busted phone gather dust, turn it into a full fledged media center! These quad core beasts can do so much more than the phones of a few years ago. I take no credit for anything here, as I'm just passing along my experience so others can make use of a disabled phone.
I have used Plex, Chromecast, etc, but no combination of those gives me the control of XBMC, and the ability to play mostly any codecs without the need for transcoding.
A few things before I get into the steps:
1. I started with a rooted phone, but you don't necessarily need one. It just helps later on if you want more control over the device functions.
2. I recommend using the most up to date firmware possible, I am on 4.4.4 myself, using this rom here:
http://forum.xda-developers.com/showthread.php?t=2800414
3. You'll want a usb OTG cable like the one I used here, along with a cheapo wired usb mouse so you can control the phone until it is set up to work with a remote.
http://www.amazon.com/gp/product/B00871Q5PI/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
4. You'll also need an MHL adapter. I used this one here:
http://www.amazon.com/gp/product/B00KPXI4S2/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
5. You'll need wifi, assuming you have moved the sim to your next device.
6. You will want some form of controlling XBMC remotely. I use Yatse for Android, installed on my replacement phone and it's a godsend.
https://play.google.com/store/apps/details?id=org.leetzone.android.yatsewidgetfree&hl
Here we go.
1. Clean that busted phone up. Reset to factory settings, flash a new rom, OR just remove any non-essential apps. I only have my phone signed into Google so I can access the Play store, which you will want to do as well.
2. Install this if you are rooted. It will allow the phone to disable the screen when the MHL adapter is plugged in, saving battery and keeping it nice and dark around your TV. The wizard should guide you through a fairly simple set up. What you are looking for is for the app to disable/suspend/standby the screen when it detects MHL.
https://play.google.com/store/apps/details?id=com.nkahoang.screenstandby&hl
3. Install SPMC. This is a forked version of XBMC for Android, and frankly, it's better suited for this application. It has more features, and takes better advantage of the hardware.
https://play.google.com/store/apps/details?id=com.semperpax.spmc
4. After installing SPMC, you can use it as a launcher, meaning the phone will boot directly into SPMC. Just press home and you'll be given the option.
5. Launch SMPC, go into Settings-Services-Webserver and check Allow control of XBMC via HTTP.
6. At this point, you can now control SPMC with Yatse or another similar XBMC remote app on another device. Depending on your situation, you may still want that mouse to do a few more things before you connect to the TV.
Options Options Options
I use XBMC in my living room on a dedicated PC. My media resides on a NAS, wired via gigabit ethernet to an AC wireless router. Since I wanted to use this broken phone as a sort of satellite system in the bedroom, I set up a MySQL server on the same NAS. It can be daunting, but XBMC provides great documentation and this method makes getting your media onto the phone very easy.
http://kodi.wiki/view/MySQL
If you do not have another XBMC or do not wish to share the library between devices, skip this section.
1. If you have another instance of XBMC, give this a serious look, as both the library and the playback status will be synced among all devices. You can stop in one room and resume in another.
2. Running the current version of SPMC, and XBMC 13.2, I had no issues with MySQL, despite the warning to use the same build date.
3. If you have this type of setup, all you need to do is copy the advancedsettings.xml file you created from your original XBMC install, and paste it into the userdata folder deep inside the SPMC file structure. This is usually found inside sdcard/Android/data
4. Once you do this, launch SPMC and your existing library will be there.
5. I have not tried this, since I went through the trouble to set up MySQL before, but you can alternatively use Media Browser 3 to serve up your library, and it does appear
to be easier to set up. Download the XBMB3C plugin inside XBMC/SPMC to allow for this.
http://mediabrowser.tv/download/#server
Add Media
Alternatively, you can navigate to videos inside SPMC, select files, and then choose Add Source to add your media from wherever to your new library. There is lots of documentation over at the official XBMC site, so go there if this is your first foray into this type of thing.
I've found that I just have to turn the phone on when I walk into the bedroom, and it will boot directly into SPMC. From that point I can use Yatse on a different device to control the media center. When I am done watching content, the shutdown option inside Yatse will shut the phone off, and it just goes into a powered down charging state.
Mostly everything should play after the install, but you may need or want to adjust some settings inside SPMC/XBMC. Again, look to the official XBMC wiki for help if you need it.
Click to expand...
Click to collapse
Im confused. How does the phone charge while its hooked into the TV?
Roseysdaddy said:
Im confused. How does the phone charge while its hooked into the TV?
Click to expand...
Click to collapse
The mhl adapter is powered.
http://ecx.images-amazon.com/images/I/71TmMtz9uIL._SL1500_.jpg
One port to rule them all
adfurgerson said:
The mhl adapter is powered.
http://ecx.images-amazon.com/images/I/71TmMtz9uIL._SL1500_.jpg
Click to expand...
Click to collapse
I have a Galaxy Note 2 with the same issue,
What is confusing me here is the phone has one MicroUSB into which three things need to plug into it
Power
OTG for Mouse and Keyboard
MHL adapter
ShiversZN said:
I have a Galaxy Note 2 with the same issue,
What is confusing me here is the phone has one MicroUSB into which three things need to plug into it
Power
OTG for Mouse and Keyboard
MHL adapter
Click to expand...
Click to collapse
1. The mhl is a Y cable with a male micro usb on the end of cord and a female at the end with hdmi that requires power which runs adapter and charges phone.
2. OTG is only for initial setup and will not be used with mhl ( OP states this is for screens that will display but not respond to touch) after setup control will be via a second device using yatse or another remote control app.
3. See #1.
This thread is great i ened up doing this very thing after destroying the digitizer on an s3 a while ago (I was one unlucky sap to try replacing a cracked screen) and the resultof having a usless phone was made better by having a perminant xbmc device connectd to my tv-way better than satellite or cable
Awesome!
I have a few devices that I keep around. Note 2, galaxy S2, nexus 1 (and my retarded/retired phones iphone 5S, ipad and blackberry playbook). I will definitely give it a try and let you guys know how it goes.
Have you tried on your S2?
Although I've touch screen working, but my gorilla glass is broken. I dont know some are saying that they've to replace whole assemble costing $125 here. While some people on the internet say that it can be done and on ebay I saw front panel(Gorilla) being sold in India.
I just came across this thread after my own experiences with getting this going yesterday! I have an LG Optimus G (E973) with a cracked digitizer, and I was about to buy an Android box, when I realized this phone would be more powerful, and have more features, than anything I could buy in the $100 range.
I made an OTG cable myself. Very easy to do, all you need is a microUSB cable male end, and a USB female end... except, problem #1, I found out my phone doesn't support OTG power. So I had to turn it into an OTG Y-cable so it can receive power (and charge the phone) simultaneously. Then, problem #2, my kernel doesn't support OTG. I wasn't able to figure this out. So I looked for another solution.
Maybe I could install VNC or one of those ADB viewers? Hook up my computer... problem #3, not authorized for adb. Can't authorize without touchscreen. (I later discovered the device keys are stored at /data/misc/adb/adb_keys, and could have added my computer in recovery.) Went to the gf's house and found my old MacBook Air, turns out that one was authorized!
Great! I'm in... now... after fiddling around trying to get it to work in Windows and OSX, problem #4 neither VNC or ADB viewers worked. I could SEE the screen, but interaction did nothing.
Eventually, I decided to just manually run touch events from the adb shell, a la adb shell input swipe 0 0 0 1280 to pull down the menu. Armed with this, I hacked together a script with JavaScript and PHP to have a web interface I could interact with my phone through. It's SLOW as hell at 768x1280 (max 1fps, I'd say), as it uses screenshots.
If anyone is interested, here's the script I made. https:// gist.github.com/shahyar/8d24815b54b8ca1c1d9c
...It didn't end there. I decided now that I have it working, I'll reset the data. Problem #5: I forgot that this also resets debug to off. I had to calculate, using a ruler, where to swipe and tap to enable developer mode, and then enable USB debugging. I wrote an init.d script which did this.
Now, I'm just waiting for my MHL cable and Bluetooth keyboard. Let's hope those go a little better than how the rest of this adventure did.
Screen cracked and not usable
I have a further issue in that my screen is cracked and I can't see what's happening on the screen.
Any thoughts on how to set it up in this case?
Great guide, thank you for taking the time to write it mailme45
tithij said:
I have a further issue in that my screen is cracked and I can't see what's happening on the screen.
Any thoughts on how to set it up in this case?
Click to expand...
Click to collapse
I was in a similar situation when I embarked on this little project, my screen was completely dead but i could hear sounds from the physical buttons so I knew the phone was on. There are a few solutions to get your phone setup, assuming you are still looking for a solution, if not I'll just mention it for the next person in this predicament. If you didn't buy your mhl adapter yet and your screen doesn't work at all, then I suggest buying a mhl cable with CEC function; this will allow you to control your phone with your tv remote when connected. These mhl adapters cost more than the ones found on ebay but also come with more features. The rocketfish RF-G1171($12 at bestbuy) for example will work with most phones including 11-pin samsung models so if you didn't buy a mhl yet, I would recommend getting one with CEC or one that comes as part of a hub, search ebay for the 5in1 mhl. If you already bought a cheap ebay one, continue reading below.
You will need a mhl cable, otg cable and usb mouse/keyboard; These steps are for people with a dead screen and digitizer. If your screen works but touch does not, just use a otg cable and mouse and if your screen doesn't work but touch does then use mhl cable and control using the touch screen.
Note** If you had USB debugging enabled already, skip to step 5
Step 1: connect the MHL cable to your phone and connect with your TV/Monitor and wait for your device to boot into the lockscreen
Step 2: Once at the lockscreen take out the mhl cable and use the otg cable to connect your mouse and swipe to unlock, switch back to mhl cable to make sure you got passed the lockscreen.
Note** If you had a password lock or pattern lock this will be very annoying, use the otg with keyboard if its a password and use mouse for pattern; might take awhile since you will be doing the pattern blind.
Step 3: use the keyboard to navigate to Settings > About Phone > scroll to "build number" and hit enter 7x to turn on developer options.
Note** As each phones menu, app layout and UI is slightly different, you may have to switch between mhl and otg just to see where you currently as you navigate. I suggest taking your time and switching between the two for each action you make, as we will only have to go through this process once.
Step 4: with developer options enabled, navigate to the "developer options" menu and turn on USB debugging.
Step 5: At this stage there are two methods, if you are lucky option 1 will work, if it does not, sadly you will have to go through the annoying mhl/otg switching to navigate one more time.
Option 1:
Install a google chrome app/extension called Vysor on your pc
Link: Vysor
This is an app developed by Koush that allows you to connect, view and control your android device on your PC through USB. The app is still in beta phase so might not work with every phone. Drivers will need to be installed for this app to work, which can be found at the Vysor homepage(I can't link to outsite sites so just google it) along with instructions. If the app works for you, I suggest the first thing you do is turn off certain features like lockscreen and sleep timer; next install a bluetooth keyboard/mouse/controller, something that will allow you to control the phone when connected to the tv/monitor through mhl. Finally you can also do all the required setups mentioned in this thread to get kodi running and when you are satisfied with the setup, connect the phone back to the tv/monitor.
Option 2:
If you were unlucky and Vysor did not work for you, navigate to the play store by switching between mhl and otg and install an app called Teamviewer Quicksupport. Install teamviewer on your PC; launch the app on your phone and you will be given an ID, use the ID on your PC to connect to the phone. When you try to connect from your PC, you will get a confirmation on your phone; make sure your phone is connected through mhl so you can see the confirmation. switch to otg to accept then switch back to mhl since you will be prompted to install an add-on, this add-on is necessary to view your phone screen on your PC. Once the add-on is installed, you will be able to see and control your phone from your pc, use your pc to setup your phone. As mentioned in option one, turn off certain features that are hindrance like lockscreen and install a bluetooth device that will let you control your phone wirelessly.
Hope this helps people with a completely dead screen but otherwise working phone, It can be very frustrating and time consuming but once you get past the initial stuff, you should be able to either link using vysor or wirelessly using teamviewer for feature setups.
So this is a great idea, except that it doesn't work for any other apps, since I do most of my watching on Netflix and HBO and I can't figure out a way to control the phone outside of Kodi.
I've just received my first android TV box, this one
https://banggood.onelink.me/zMT7/wda08nyk, and I was wondering if anyone knew where I can go to get alternative ROMs for it? I'm specifically looking for Android TV based ROMs, as it ships with standard android (pretending to be a pixel 3).
I haven't found any. It's still a very new device. There are updated stock FW, though. Not much of an improvement. Here are updated stock Images.
Hello
Same problem here, it is pretending to be Googlre pixel 3
Any idea when would someone make Android TV based ROM?
If you own one of these H618 devices, can you please run the following command on your device to see if it has malware similar to the T95 H616?
Code:
adb shell "getprop ro.product.device ; [ -d '/data/system/Corejava' ] && echo 'Corejava exists' ; ! [ -d '/data/system/Corejava' ] && echo 'Corejava not present'"
Thanks!
Hi I am trying to connect my android box T95z plus to a Samsung tv, but when I try the signal is not getting though, although the hdmi connection is found there is a red cross symbol by the hdmi icon on TV.
However I can connect the Bix to my other fire tv with no issue and same cable!
This is really driving me mad.
And advice greatfully received thanks in advance
Jonnybourne said:
Hi I am trying to connect my android box T95z plus to a Samsung tv, but when I try the signal is not getting though, although the hdmi connection is found there is a red cross symbol by the hdmi icon on TV.
However I can connect the Bix to my other fire tv with no issue and same cable!
This is really driving me mad.
And advice greatfully received thanks in advance
Click to expand...
Click to collapse
this issue is common, the tvboxes don't support every possible resolution out there, your tv may have a specific resolution or refresh rate that isn't supported by the tv box, so the tv box can't switch to the correct resolution because it doesn't exist.
i'm not by my tv box now, but if i recall correctly, there is usually an option to disable automatic switching to the correct resolution, you can turn that off so the box doesn't automatically switch to a resolution the TV chooses. then plugin the box to a monitor or another tv, choose a resolution manually on the tv box, then plug it back to the samsung tv, if still no signal, repeat the process with a different resolution.
this worked for me with 2 tv boxes Q96+ and HiMedia Q5 or Q7 i can't recall, but also hasn't worked with every box that did that, so it's a hit or miss.
good luck
You may want to try something like THIS. I had similar issues with both h616 and h618 boxes. In the settings for display, the h616 had a toggle for TV HDMI control.