Hi, I need help here. I got an At&t HTC TITAN PI3900 stuck in bootloader mode - When turned off, pressing the power button or plugging the charger or usb would automatically brings the bootloader screen.
Things that I did:
Upgraded to the SPL (2.6?) from the HTC website to fix the unlock code problem re-entering it everytime I reboot.
Forced flash the WP 7.8 via seven-eighter, and everything is just fine.
Tried debranding and installinhg HSPL but all failed:
Goldcard via Y Cable was ok but when trying to flash EU ROM (IMG_Eternity_HTC_Europe_1.09.401.02_Radio_16.23.02.09_A_16.24.00.23_Signed_ETERNITY_RELEASE) via Goldcard method, it says "NOT ALLOW"
Tried to flash via Goldcard also the Cingular ROM ( IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE) but always fails - OS and RADIO - Internal error or something
At this moment, the phone is still fine and working perfectly
The I flash via RUU (bootloader mode) the stock Cingular ROM same as the above,
( IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE), error came - ERROR [226] FLASH WRITE ERROR
Tried to flash again the 2 ROMS mentioned above a couple of times via RUU, re-downloaded the ROM would still give me the same error. Also tried the TitanAdvancedRUU-V1.0.5, but still the same error.
Now my phone is stucked at bootloader screen. It can't enter also the USB HOST MODE, I don't know why
The bootloader screen says:
PI39100
SPL-2.6.160015.3 (140182)
eMMC SND 15188MB
TOUCH A1(F:81, ID:1. V11, B:F8)
Radio-16.23.02.26A
Serial
APPSBL
IMAGE CRC
FACTORY RESET
Any help or suggestion would be greatly appreciated
Help
Nevermind, I got it working again! I just reflashed the stock 2.6 SPL from HTC and BOOM!
da_mayhem said:
Nevermind, I got it working again! I just reflashed the stock 2.6 SPL from HTC and BOOM!
Click to expand...
Click to collapse
i can't find stock roms on the htc site.. can you give me the link?
da_mayhem said:
Nevermind, I got it working again! I just reflashed the stock 2.6 SPL from HTC and BOOM!
Click to expand...
Click to collapse
There is no mention of SPL205 in any of your steps; had you successfully done that your SPL would be 2.5.160015 not 2.6.160015; it is once you've successfully flashed that step you would proceed to HSPL; however, if you're using the official stock 7.8 you're fine.
Tgodfather said:
i can't find stock roms on the htc site.. can you give me the link?
Click to expand...
Click to collapse
No bro, it's just the bootloader update posted on the HTC site, no roms posted over there
berrywr said:
There is no mention of SPL205 in any of your steps; had you successfully done that your SPL would be 2.5.160015 not 2.6.160015; it is once you've successfully flashed that step you would proceed to HSPL; however, if you're using the official stock 7.8 you're fine.
Click to expand...
Click to collapse
Yes I wasn't able to get it to SPL 2.5 that's why I can't proceed to the HSPL procedure, I don't know why I was having a "NOT ALLOW" error when flashing stock Cingular ROM via Goldcard
da_mayhem said:
Hi, I need help here. I got an At&t HTC TITAN PI3900 stuck in bootloader mode - When turned off, pressing the power button or plugging the charger or usb would automatically brings the bootloader screen.
Things that I did:
Upgraded to the SPL (2.6?) from the HTC website to fix the unlock code problem re-entering it everytime I reboot.
Forced flash the WP 7.8 via seven-eighter, and everything is just fine.
Tried debranding and installinhg HSPL but all failed:
Goldcard via Y Cable was ok but when trying to flash EU ROM (IMG_Eternity_HTC_Europe_1.09.401.02_Radio_16.23.02.09_A_16.24.00.23_Signed_ETERNITY_RELEASE) via Goldcard method, it says "NOT ALLOW"
Tried to flash via Goldcard also the Cingular ROM ( IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE) but always fails - OS and RADIO - Internal error or something
At this moment, the phone is still fine and working perfectly
The I flash via RUU (bootloader mode) the stock Cingular ROM same as the above,
( IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE), error came - ERROR [226] FLASH WRITE ERROR
Tried to flash again the 2 ROMS mentioned above a couple of times via RUU, re-downloaded the ROM would still give me the same error. Also tried the TitanAdvancedRUU-V1.0.5, but still the same error.
Now my phone is stucked at bootloader screen. It can't enter also the USB HOST MODE, I don't know why
The bootloader screen says:
PI39100
SPL-2.6.160015.3 (140182)
eMMC SND 15188MB
TOUCH A1(F:81, ID:1. V11, B:F8)
Radio-16.23.02.26A
Serial
APPSBL
IMAGE CRC
FACTORY RESET
Any help or suggestion would be greatly appreciated
Help
Click to expand...
Click to collapse
had the same problem..scared the crap out of me...Installing SPL 2.6 seems to be working for this problem...even though we are stuck on 2.5.
Did you manage to get HSPL working?
da_mayhem said:
Did you manage to get HSPL working?
Click to expand...
Click to collapse
nada...nope...
I tried pretty much everything. So has Nikola, on this board...
I think some AT&T Titans and their nand memory get shot after trying to HSPL or debrand.
-Which therefore could be linked to a manufacturing problem with the Titan.
---As technically, my other AT&T Titan had no problem whatsoever getting the HSPL installed.
I guess I have to stop trying now Guess we'll be stuck at the official 7.8 for a while not until DFT releases something for us
da_mayhem said:
I guess I have to stop trying now Guess we'll be stuck at the official 7.8 for a while not until DFT releases something for us
Click to expand...
Click to collapse
Yea....
Anyway yea, at least you get 7.8 and not a brick -or a phone that is stuck at 7.5.
da_mayhem said:
No bro, it's just the bootloader update posted on the HTC site, no roms posted
Click to expand...
Click to collapse
it is just what i'm looking for dude! I'm stuck at the 1.8 bootloader version. Can you link me the update? I'm italian, and in HTC.it there isn't any update
EDIT: nevermind, i've found it
Related
I restored the stock vodafone rom and then flashed the stock spl now when i turn the phone on i get the spl screen and it say
upgrade rom code error
then i get a grey screen that says Loading... nothing more
lohap said:
I restored the stock vodafone rom and then flashed the stock spl now when i turn the phone on i get the spl screen and it say
upgrade rom code error
then i get a grey screen that says Loading... nothing more
Click to expand...
Click to collapse
How did you flash the original SPL?
As far as I know there is no JumpSPL or SoftSPL for Raphael yet? Or am I wrong?
[EDIT] Sorry, I've seen how it's possible in the Wiki.
Per the instructions at
http://forum.xda-developers.com/showthread.php?t=410150
now it seems to boot the stock spl but with that error
windows doesnt even detect it i think
woop got windows to detect it
problem is i cant flash the hardspl, spl and if i try to flash a stock firmware i get vendor id error, anyone got a full dump of the vodaone uk firmware
Could not you flash the ROM from memory card (when you find any)?
crocodile010 said:
Could not you flash the ROM from memory card (when you find any)?
Click to expand...
Click to collapse
problem is i cant flash the hardspl..........so 1 and 1 is 2,he cannot do that
have u tried getting in touch with olipro or cmonex? or with any members of the elite team? my guess is they are the ones with most technical knowledge of the device so ask one of them help.
ofcourse always be nice and polite and patient as those guys have their plates full
thanks ill send them a pm and see if i need to buy a new device.
hi been told i can fix this with mtty and one got a link to a download and do i need to do anything to the raphel to get it into serial mode
My HD2 stuck at the HTC boot screen. It's stock rom is RUU_Leo_hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship, but flashing is fail from PC or SD card.
Error snapshot is in attachment.
Can you help me pls?
TEEEmon said:
My HD2 stuck at the HTC boot screen. It's stock rom is RUU_Leo_hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship, but flashing is fail from PC or SD card.
Error snapshot is in attachment.
Can you help me pls?
Click to expand...
Click to collapse
What SPL are you on?
SPL-1.42.0000, but I try different SPLs and HSPLs
Hmz, I havn't seen this... Does the device boot, or does it directly go to bootloader?
Normally it's stuck at the HTC boot screen, to go to bootloader I press volume key. I try different versions of roms, but no result
TEEEmon said:
Normally it's stuck at the HTC boot screen, to go to bootloader I press volume key. I try different versions of roms, but no result
Click to expand...
Click to collapse
If it get's stuck at HTC Boot screen, you don't have a correct ready.
Try to install HSPL, and flash other radio...
Does any solutions to repair extended rom on HD2 or it's hardware issure?
xmoo said:
Try to install HSPL, and flash other radio...
Click to expand...
Click to collapse
No results
is this your stock rom?
have you tried downloading once more the stock rom from HTC's website based on your device's serial number? Error 18003 is most likely caused by flashing a corrupt file (either from the download or transfering/renaming the file to SDCard) ???
EDIT: are you sure you are not trying to flash a non-WWE version of the stock ROM without previously installing HSPL on your device?
Yes, I use firmware from HTC's website based on my device's serial number... When I flash custom roms or radio (roms, which image not contain EXTROM) it's flash well, but no result.
This morning I tried again to flash device and it flash well!! But it stuck at the HTC boot screen again. I used the same firmware as yesterday (RUU_Leo_hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship from official HTC's website) and used the same CD card as yesterday, but today it flashed well. I think, that it's hardware issue
TEEEmon said:
This morning I tried again to flash device and it flash well!! But it stuck at the HTC boot screen again. I used the same firmware as yesterday (RUU_Leo_hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship from official HTC's website) and used the same CD card as yesterday, but today it flashed well. I think, that it's hardware issue
Click to expand...
Click to collapse
maybe a bad copy/download?
Try this otherwise send it to warranty:
1) HSPL2
2) Task 29 by doonloop
3.1) Flash a stock WWE ROM (try a version 1.66) from the PC
or
3.2) Redownload your HK stock from a different source (specific thread here at XDA), rename it LEOIMG.nbh and flash it from your PC
Good luck!
Do not flash any ROM from your SD card please. Just use the recommended way - through PC.
remove sd card from your leo and try to flash rom using pc .
@mon_money..How can he flask from his pc ir phone wont boot... dont you need active sync?
I had a similar problem when i was using an incompatible radio rom for the rom i was trying to install...
copy the nbh file from the stock rom into the root of the sd. that will fix the problem..
I had a similar problem with a different ROM and I tried this suggestion provided by mskip. It does require you already have HSPL2 installed.
1. Turn your phone off and unplug it from your computer
2. Press and hold the VOLUME DOWN then Press and hold the POWER button. After about 3 seconds the tri-coloured screen should appear with the "SERIAL" driver displayed at the bottom
3.connect it to your pc it should install drivers.the screen should now say "USB"
4.reflash with std rom/radio, known working ROM, or original OEM rom - TMOUS has a bundled 2.13 download from their website.
Good luck.
slatiwonk said:
4.reflash with std rom/radio, known working ROM, or original OEM rom - TMOUS has a bundled 2.13 download from their website.
Click to expand...
Click to collapse
probably best you don't use the 2.13. chances are it would be fine, but this rom seems to be pretty good at updating the spl to 2.1
not a problem for tmous users who can downgrade using rom 2.10 but that only works because their phone is tmous. the OPs phone isn't.
im pretty sure it just simply wouldn't work, but whilst you are already having problems, don't run the risk.
I try all this solutions but no result
This device was purchased new aprox. 6 weeks ago.
I flashed HSPL1 and updated the radio to Leo_RADIO_2.07.50.27_2
Then flashed Energy rom of my choice. via custom ruu.
I flashed lots of roms or the course of several weeks and have lots of prior experiance with custom rom flashing on many devices so this was nothing new.
The device worked great for this long and then yesterday updated Rom to
Energy Rom July 1.
When the device was finished flashing it auto started in the Bootloader screen.
I tried redownloading the rom and reflashing. Still started in bootloader.
Tried reflashing to previous working rom but it still started in bootloader.
Next I did a task 29 "format"
downloaded an official rom. RUU_Leo_Telstra_WWE_1.72.841.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship
Extracted the .nbh to a freshly formated FAT32 2gig mem card and reflashed via mem card.
The screen showed the progress like normal and the flash displayed "Successful".
When I rebooted the device it once again started in Bootloader.
This time:
PB81110 HX-BC
SPL-1.66.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
so I am pretty sure that the bootloader and possibly radio and rom are correctly flashed but something is making it start in bootloader.
Any thoughts??
sticky 'down vol' button? try holding just 'vol up', , see if it starts a hard reset, , if it does then you know the vol down button was registering as pressed.
shenweas said:
This device was purchased new aprox. 6 weeks ago.
I flashed HSPL2 and updated the radio to Leo_RADIO_2.07.50.27_2
Then flashed Energy rom of my choice. via custom ruu.
I flashed lots of roms or the course of several weeks and have lots of prior experiance with custom rom flashing on many devices so this was nothing new.
The device worked great for this long and then yesterday updated Rom to
Energy Rom July 1.
When the device was finished flashing it auto started in the Bootloader screen.
I tried redownloading the rom and reflashing. Still started in bootloader.
Tried reflashing to previous working rom but it still started in bootloader.
Next I did a task 29 "format"
downloaded an official rom. RUU_Leo_Telstra_WWE_1.72.841.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship
Extracted the .nbh to a freshly formated FAT32 2gig mem card and reflashed via mem card.
The screen showed the progress like normal and the flash displayed "Successful".
When I rebooted the device it once again started in Bootloader.
This time:
PB81110 HX-BC
SPL-1.66.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
so I am pretty sure that the bootloader and possibly radio and rom are correctly flashed but something is making it start in bootloader.
Any thoughts??
Click to expand...
Click to collapse
Only time I can make my phone do that is a) I've just done a task29 and there just isn't anything to load, b) I've flashed a rom incompatible with the radio currently installed or vice versa. So the flashes can be all fine but something is just stopping it at the door. Hmph, wish I had the silver bullet for ya bro. Best of luck.
shenweas said:
This device was purchased new aprox. 6 weeks ago.
I flashed HSPL2 and updated the radio to Leo_RADIO_2.07.50.27_2
Then flashed Energy rom of my choice. via custom ruu.
Click to expand...
Click to collapse
it is my understanding that you are not suppose to use HPSL2 on the Telstra, you can use HSPL or HSPL3, did you mean to say you use 1 or 3?
samsamuel said:
sticky 'down vol' button? try holding just 'vol up', , see if it starts a hard reset, , if it does then you know the vol down button was registering as pressed.
Click to expand...
Click to collapse
Holding only Up-Vol button and powering on = still starts in bootloader
alwayslearning said:
it is my understanding that you are not suppose to use HPSL2 on the Telstra, you can use HSPL or HSPL3, did you mean to say you use 1 or 3?
Click to expand...
Click to collapse
Yes I meant to say 1.
I also tried both versions of 3.
it is back to spl now though since I flashed the offical rom. which has the radio included as indicated in forst post.
Thanks for all your good ideas I am trying them as you send them this way.
I am thinking if may be a hardware issue but am trying what I can before sending it in.
BTW the mem card I am using is SanDisk 2GB.
Does anyone think after reading previous posts that I should go out and buy a different card "just to try"?
no, you shouldnt need to use sd card at all. Ive only used sd card with this phone once, and that was just to test removing hspl 1.42 6 months ago.
You dont have hspl installed and the stock rom should flash over usb anyway. (You have tried that, right? boot to bootloader, connect usb, run the telstra .exe)
samsamuel said:
no, you shouldnt need to use sd card at all. Ive only used sd card with this phone once, and that was just to test removing hspl 1.42 6 months ago.
You dont have hspl installed and the stock rom should flash over usb anyway. (You have tried that, right? boot to bootloader, connect usb, run the telstra .exe)
Click to expand...
Click to collapse
Yes it flashes normal over usb using RUU exe file. Everything looks normal until it reboots. Then it starts in Bootloader.
Have you checked if the ROMs you downloaded were complete? Are you sure they weren't corrupt? Tried flashing a generic WWE ROM? Also, flashing via USB is apparently a better flashing method than MicroSD.
aethelbert said:
Have you checked if the ROMs you downloaded were complete? Are you sure they weren't corrupt? Tried flashing a generic WWE ROM? Also, flashing via USB is apparently a better flashing method than MicroSD.
Click to expand...
Click to collapse
I am unfamiliar with how to check if the rom download is complete. However, I tried flashing roms that were working on the device before and that i still have on my PC with the same results. I tried several custom roms and official htc rom. along with a WWE rom.
Still no Joy.
shenweas said:
I am unfamiliar with how to check if the rom download is complete. However, I tried flashing roms that were working on the device before and that i still have on my PC with the same results. I tried several custom roms and official htc rom. along with a WWE rom.
Still no Joy.
Click to expand...
Click to collapse
I have the Telstra version myself and I HSPL (number 1) always use the USB method and have never had any issues.
One thing I did do, I flashed an official HTC non-Telstra version first. Then I flashed just a radio. Then I flashed Miri's ROM and everything worked. I have flashed Miri's version from 1 to 17.5 all using USB
you may want to try a different PC, I have heard of people who did this and it worked for them
alwayslearning said:
I have the Telstra version myself and I HSPL (number 1) always use the USB method and have never had any issues.
One thing I did do, I flashed an official HTC non-Telstra version first. Then I flashed just a radio. Then I flashed Miri's ROM and everything worked. I have flashed Miri's version from 1 to 17.5 all using USB
you may want to try a different PC, I have heard of people who did this and it worked for them
Click to expand...
Click to collapse
Thanks for the idea.
Tryed re-downloading the official rom from HTC and re-flashed from a different computer via usb RUU.
Flash completes perfectly fine and RUU says ready for use. The device still restarts in bootloader
shenweas said:
Thanks for the idea.
Tryed re-downloading the official rom from HTC and re-flashed from a different computer via usb RUU.
Flash completes perfectly fine and RUU says ready for use. The device still restarts in bootloader
Click to expand...
Click to collapse
try: make sure you do not have an SD card in slot, right after the flash do a hard reset
alwayslearning said:
try: make sure you do not have an SD card in slot, right after the flash do a hard reset
Click to expand...
Click to collapse
Restart after flash with no card in slot has this result.
first screen is "Restore Waiting for completed" with progress bar that completes in aprox 3 sec.
the next screen is "Restore.....Completed
Press VolUp to boot
I press VolUp and the bootloader appears again Thanks for the idea.
I will keep trying to work on this untill tue which is the next time the mail runs here. Will probably have to ship it to HTC CS to get it fixed. I am thinking something is wrong in the hardware.
Could it be possible that a chef could have got the rom versions mixed up and i ended up with a tmoble rom without knowing it or is this unheard of???
What would have happened if I did flash a Tmo rom?
shenweas said:
Could it be possible that a chef could have got the rom versions mixed up and i ended up with a tmoble rom without knowing it or is this unheard of???
What would have happened if I did flash a Tmo rom?
Click to expand...
Click to collapse
Just a thought , have you tried flashing it with USB, without the SD card in it and rebooting before putting it back in ....
shenweas said:
Could it be possible that a chef could have got the rom versions mixed up and i ended up with a tmoble rom without knowing it or is this unheard of???
What would have happened if I did flash a Tmo rom?
Click to expand...
Click to collapse
I use Miri's ROM and it is a Tmo version. Just make sure you have one the radios on his site, go here: http://htcpedia.com/forum/showthread.php?t=1786
still stuck in bootloader.
This is strange. Hard for me to believe I am the only one with this problem but could be possible.
shenweas said:
still stuck in bootloader.
This is strange. Hard for me to believe I am the only one with this problem but could be possible.
Click to expand...
Click to collapse
I have never heard of anyone stuck on the Stock bootloader where the phone was not bad ...
but just for the sake of trying, try holding the UP and Down at the some time when powering on, I know that is supposed to only do a hard reset, but maybe it will kick it off ....
anything is worth a shot at this point ....
Well as tittle says, i have famous at&t tiatan with 2.05 spl and error F400, was showing USB and SERIAL, now since i tried usb stick and sd card with reader on HTC HD7 confirmed to work, i start proces with titan and i get kicked to BL screen, now what is unexpected is that i, for fun only, flashed this IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE.nbh via ROMupdateutillitytool and it flashed But what is main thing is spl didnt changed, nor radio, just FW it is now at&t US rom, I had EU .401 region ROM before, my humble question is should is use hammer on my titan or what? Is there a way to go back to .401 region ROM
thx in advance
EDIT: Well this is even more strange, via goldcard i now flashed same Cingular ROM, but why when i try to flash any other ROM via gold card i get knocked out of USB host mode into bootloader mode?
nikola92 said:
Well as tittle says, i have famous at&t tiatan with 2.05 spl and error F400, was showing USB and SERIAL, now since i tried usb stick and sd card with reader on HTC HD7 confirmed to work, i start proces with titan and i get kicked to BL screen, now what is unexpected is that i, for fun only, flashed this IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE.nbh via ROMupdateutillitytool and it flashed But what is main thing is spl didnt changed, nor radio, just FW it is now at&t US rom, I had EU .401 region ROM before, my humble question is should is use hammer on my titan or what? Is there a way to go back to .401 region ROM
thx in advance
EDIT: Well this is even more strange, via goldcard i now flashed same Cingular ROM, but why when i try to flash any other ROM via gold card i get knocked out of USB host mode into bootloader mode?
Click to expand...
Click to collapse
Why did you flash to the Cingular Rom? From what I understand...you can get rid of the f400 error if you flash via goldcard the stock rom that you had before. Did you try this yet? and did you try flashing to your EU stock rom via the RUU too?
I read over on the DFT thread and noticed you were trying to install DFT's HSPL a couple of days ago. Do you know what SPL version you had before you tried to HSPL?
xconomicron said:
Why did you flash to the Cingular Rom? From what I understand...you can get rid of the f400 error if you flash via goldcard the stock rom that you had before. Did you try this yet? and did you try flashing to your EU stock rom via the RUU too?
I read over on the DFT thread and noticed you were trying to install DFT's HSPL a couple of days ago. Do you know what SPL version you had before you tried to HSPL?
Click to expand...
Click to collapse
Why i tried well because not a single one other Stock ROM was flashable via RUU or Goldcard, even stock Cingular ROM wasnt flashable via RUU i only mmanaged to flash it via goldcard. Well I was trying too to get rid of F400 but the thing is my titan is AT&T he was branded, before i bought it someone placed 2.05 spl on it and unlocked it, to meake it simple i got my titan with 2.05 spl, F400 and was x310e in about, every my atempt to flash something via goldcard was failure because it connects with usb stick in USB host mode , it says "Loading..." and then kicks me out to BL screen, exept the 1.10 cingular ROM, hehe but what is funny i get rid of F400 that way but my SPL stayed on 2.05..... :silly: iwill try the famous Tango ROM 4.16 spl i dont care anymore i am pissed or i will do that or use a hammer on this american junk... I had a lot of phones and not a single one was anoying as this one.....
Hello, please help regarding my HTC HD2. I tried everything but nothing helps. I'm trying to restore WP 6.5, but it keeps coming back to the bootloader. here's what I've tried:
1st made the task 29 (after installing HD2 returned to the bootloader)
2nd installed radio Radio_Leo_2.15.50.14 (after installing HD2 returned to the bootloader)
3rd installed Hsp 08.02 (after installing HD2 returned to the bootloader)
4th installed signed RUU (after installing HD2 returned to the bootloader)
-Installation went through with no problems and always come back to the bootloader ??
-I tried the installation via a micro SD card but throws an error 'update rom code error ... not allowed)
-Magdlr 113 installed without problems but returns to the bootloader after restarts
- I tried with MTTY but always the same, restart and returns to the bootloader
- I tried with 3 diferent RUU (all for my country) and nothing
Any solutions? All comments are welcome. Ty
upravnik said:
Hello, please help regarding my HTC HD2. I tried everything but nothing helps. I'm trying to restore WP 6.5, but it keeps coming back to the bootloader. here's what I've tried:
1st made the task 29 (after installing HD2 returned to the bootloader)
2nd installed radio Radio_Leo_2.15.50.14 (after installing HD2 returned to the bootloader)
3rd installed Hsp 08.02 (after installing HD2 returned to the bootloader)
4th installed signed RUU (after installing HD2 returned to the bootloader)
-Installation went through with no problems and always come back to the bootloader ??
-I tried the installation via a micro SD card but throws an error 'update rom code error ... not allowed)
-Magdlr 113 installed without problems but returns to the bootloader after restarts
- I tried with MTTY but always the same, restart and returns to the bootloader
- I tried with 3 diferent RUU (all for my country) and nothing
Any solutions? All comments are welcome. Ty
Click to expand...
Click to collapse
I tried with different batterie,usb cable and micro sd card as well, still same problem. please help!!
I would reflash HSPL 2.08
then try custom WM6.5 ROM from link in HD2 Wiki & then a radio too ...
http://forum.xda-developers.com/wiki/HTC_HD2#ROM_Development
ROM code error would suggest you got no HSPL & ROM code of roms you are trying are not correct, ROM code is region & vendor specific but with working HSPL and USB flashing it is bypassed, dlashing via SD card removes HSPL at first step then if wrong ROM code it fails to flash so you are best sticking with USB flashing.
Mister B said:
I would reflash HSPL 2.08
then try custom WM6.5 ROM from link in HD2 Wiki & then a radio too ...
http://forum.xda-developers.com/wiki/HTC_HD2#ROM_Development
ROM code error would suggest you got no HSPL & ROM code of roms you are trying are not correct, ROM code is region & vendor specific but with working HSPL and USB flashing it is bypassed, dlashing via SD card removes HSPL at first step then if wrong ROM code it fails to flash so you are best sticking with USB flashing.
Click to expand...
Click to collapse
Thank you for answer
HSPL 2.08 was re-fleshed (with HSPL 4) each time after attempting to install via SD card, that's OK.
I tried to install this three ROMs:
RUU_Leo_S_TMO_HR_3.14.119.1_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
RUU_Leo_TMO_HR_1.66.119.0_Radio_Signed_15.31.50.07U_2.07.51.05_2_Ship
RUU_Leo_TMO_HR_1.72.119.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship
I followed all the steps that returns the WP on the phone, and HD2 do everything, except the most important one, not raise OS.
ROMs installation runs without any problems via USB but when HD2 should run WP 6.5, HD2 returns to the bootloader. And now when I turn on the phone automatically starts in bootloader.
Flash SPL 3.03HSPL then flash the 3.14 ROM via USB
Do you get 100% progress bar on the HD2 while flashing ?
If completes ok try rebooting but do so via reset button on back of HD2 & see if boots.
If still going to bootloader try reflashing just the ROM radio 2.15.50.14 from link in HD2 wiki as they known working radio ROMs.
Try rebooting again & using reset button on rear to see if helps get proper boot.
If still fails try flashing Radio ROM again but from sd card & test boot again :-S
Mister B said:
Flash SPL 3.03HSPL then flash the 3.14 ROM via USB
Do you get 100% progress bar on the HD2 while flashing ?
If completes ok try rebooting but do so via reset button on back of HD2 & see if boots.
If still going to bootloader try reflashing just the ROM radio 2.15.50.14 from link in HD2 wiki as they known working radio ROMs.
Try rebooting again & using reset button on rear to see if helps get proper boot.
If still fails try flashing Radio ROM again but from sd card & test boot again :-S
Click to expand...
Click to collapse
Thanks for the help, but still nothing.
I followed all the steps that you wrote and at the end, again the same - the bootloader.
- SPL 3.03HSPL flashed OK, pic 1
- Flashed 3.14 ROM via USB, 100% progress on HD2 and PC, pic 2
- for reset I used button on rear, and HD2 returned to bootloader
- after that I tried installation via SD card (formated to FAT32), pic 3
- installation stopped after this point, pic 4, and i got this messages pic 5 and pic 6
I don't know is this important but, after each installation, before entering the bootloader, the screen shortly flashed and in the background I can see 'loading' but quickly bootloader start again.
I think it's something wong in the HD2 because in the bootloader I can not see the radio version at the bottom of the screen. I'm not sure, but at the previous installation (before it broke) I was able see that. Thank you again
Problem is it not flashing radio &/or suspect Radio nand is bad !
You want flash HSPL & the ROM via USB then try just flashing a Radio via USB & SD, not the complete ROM as via SD that removes the HSPL then you get those error messages as wrong original ROM for region/vendor.
Just try various attempts with 2 radio roms linked below (rename same as a full ROM to flash via SD) & hope you get lucky !
http://www.datafilehost.com/download-0f71cda2.html
http://www.datafilehost.com/d/9b79ee41
Mister B said:
Problem is it not flashing radio &/or suspect Radio nand is bad !
You want flash HSPL & the ROM via USB then try just flashing a Radio via USB & SD, not the complete ROM as via SD that removes the HSPL then you get those error messages as wrong original ROM for region/vendor.
Just try various attempts with 2 radio roms linked below (rename same as a full ROM to flash via SD) & hope you get lucky !
http://www.datafilehost.com/download-0f71cda2.html
http://www.datafilehost.com/d/9b79ee41
Click to expand...
Click to collapse
Thanks for your help. I installed the radio via sd card with no problem but when installing the ROM again the same problem. I think it's best to leave the HD2 to get some rest and try again when I have more time and nerves. Thank you so much for your advice. I hope I will fix it .. once