Hello
I can not upgrade L9. I tried many times by kdz by its not working.
LG upgrade tool can't connect with phone.
07:48:40 : 0 - NotConnected.
07:48:40 : 1 - Normal connect success
07:48:40 : 2 - Emergency connect success
07:48:41 : _IsConnectedPhone Call
07:48:50 : _IsConnectedPhone(0)
07:48:50 : 0 - NotConnected.
07:48:50 : 1 - Normal connect success
07:48:50 : 2 - Emergency connect success
07:48:50 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
07:48:56 : Check Cancel button active..
07:48:56 : Check Cancel button active..
07:48:56 : !pUpgrade->StartProcessing ... PostMsg STEP_TYPE_ENV_ERROR
07:48:56 : Page_Error şÎşĐŔÔ´Ď´Ů
07:48:56 : [011,700,147,062,092]LG Mobile Phone Software Update was canceled\n\n[009,400,102,102,102]To quit LG Mobile Phone Software Update, please press the [009,700,147,062,092]Exit[009,400,102,102,102] button below.
07:48:56 : OnStepMsg STEP_TYPE_ENV_ERROR delete m_pLGCyonUpdate
Click to expand...
Click to collapse
All drivers looks like here:
http://forum.xda-developers.com/picture.php?albumid=8677&pictureid=32161
Phone is all the time in s/w mode. Battery 100%.
I tried also LGMobile Support Tool (recovery mode), but it also lose connection.
Can anybody help me??
apa3 said:
Hello
I can not upgrade L9. I tried many times by kdz by its not working.
LG upgrade tool can't connect with phone.
All drivers looks like here:
http://forum.xda-developers.com/picture.php?albumid=8677&pictureid=32161
Phone is all the time in s/w mode. Battery 100%.
I tried also LGMobile Support Tool (recovery mode), but it also lose connection.
Can anybody help me??
Click to expand...
Click to collapse
how did you end up this way?
try disabling the lge mobile usb modem
while upgrading my battery died at 92% progress.... (battery was charged in 85%)
So I charged it again in different phone but it cannot connect with computer.
Nothing happens when I disabled usb modem.
problem solved. phone updated.
(reinstaled drivers and LG tools; then recovery mode)
please close this topic.
apa3 said:
problem solved. phone updated.
(reinstaled drivers and LG tools; then recovery mode)
please close this topic.
Click to expand...
Click to collapse
Hi apa, i'm sorry. Can you help me out here? I have the same problem you had, the phone does nothing but start SW Upgrade Mode and i dont know what to do. Can you please be a little bit more specific? I can't do nothing cause if i plug the battery in, it starts the SW, if i press the power button, it goes to SW, everything gets me to SW.
If isnt so much problem could you mail me at [email protected] so i can get the info faster
It will be highly appreciated, for real.
Thanks.
Related
Hi, because with last update increased count of people with bricket phone, I just tryed search for way how to repair this phone. It seems, that last possible way how to save your phone is emergency mode.
I would like to notify you, that I didn't tested it (I'm had not luck enough to brick my phone yet ). I just searched and tried write this for help to others.
So, let's go on.
1) If it's not possible connect to phone via ADB (in Adroid SDK/tools run "adb shell") at all you will try next steps. If it will work, you can use another, verified tools like custom recovery or KDZ_FW_UPD (search on forum for more) [HOWTO] Flash original firmware on P500, )
2) If you fail in previous step, you can try enter into emergency mode manually and try to flash ROM with KDZ_FW_UPD:
Download KDZ updater and uncompress it
http://www.4shared.com/file/UleS4dP3/KDZ_FW_UPD_EN.html
Install msxml.msi from the uncompressed directory
Charge your battery to almost full state (I'm not sure, but it can be reason if phone doesn't start)
Turn phone off somehow (remove battery etc.)
Install drivers properly
Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments
Install the LG drivers by selecting the update manager from the lg site
Disable LGE Virtual Modem. In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.
Press and keep pressed "Volume up"+"Return" and connect USB cable to phone
Yellow screen with text emergency mode should appeared
Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
Run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT (I have one report that CDMA mod works too)
Select PhoneMode : DIAG (in case of fail try EMERGENCY, and as last chance use CS_EMERGENCY)
I Recommend do not switch phone off. There was some people, which done it and after they were not be able to turn it on again. If flashing failed, just select some another mode and try it again, again, try shake/connect disconnect, again, again....
In KDZ file : Choose the ROM file you downloaded in the first step
Press Launch software update
Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
Make sure that all update was done successfully. Phone should restart itself automatically
Disconnect the USB cable from the phone
Press the three button combo for HW reset of device i.e volume up + home + power button
List to do based on Zecanilis's [HOWTO] Flash original firmware on P500
3) Still no success? Wait for more "What I can do" or just go to LG and let repair on them.
Source:
http://forum.gsmhosting.com/vbb/f282/vygis-shell-v1-1-0-josedavido-1166478/ (included file named "Flash help.txt" in application)
http://android.modaco.com/content/l...modaco-com/321895/faq-gt540-reference-thread/
Please let me know if it works. I just searched for way and I haven't possibility to test this steps for now. I will do update if it will be necessary, same as I will try describe more about software which I founded.
Some experiences from thread(s):
AVanover5: ...It works if you set the mode to CDMA and DIAG. Just to let people know. Not sure if it'd work without the recovery screen or not. I never tried it ironically, haha. Thank you guys.
geejay2: ...Bricking seems to be easily achieved by forgetting to disable the LG Modem driver. Apparently the modem driver interferes during flashing. Also I noted that kdz is not stable under Win2k, I switched to WinXP to flash successfully. I saw several aborted flashing attempts in WinXP with modem driver enabled.
domenic_s:KDZ_FW_UPD doesn't work (Application cannot start) -.- Using Windows 7 64bit version. //edit: allright tried another pc (win xp 32bit) and yeah - it worked... I'm so happy.
Click to expand...
Click to collapse
About shaking (sorry, but I still can't believe... )
salte_eskil:wow! shaking the phone really worked! seems kind of stupid but thanks to you all at the xda forum for tips and tricks
4wd vege: Now unbricked. Strangely kdz updater only saw my phone after shaking!!!
me2kimi:It sound crazy to shake the phone while at emergency mode. I's crazy but it magic. ...So what I do is connect to usb, Launch software update at kdz while shaking the phone. Then after that kdz is working like normal.
Click to expand...
Click to collapse
I tried with all possible combination.. with and without battery.. vol- home, vol + return, power vol+ home.. end more.. but phone don't turn on...
In meantimes the phone is in the service LG.. hope...
Exscuse me for my English
Did you had phone off before trying this? And also battery should be charged. I just added this things...
If event that it not show you emergency mode, LG service and warranty is probably the only way how to proceed. Sorry. But I will be searching if another way will exist...
Good work .. I hope that you will find a way to solve ... especially for other users .. good luck
Good work @The_ERROR.
It should work. I think you should also add that the phone mode should be set to Emergency (and not DIAG as mentioned) in the kdz updater.
Moved to development and stickied it for a while!
Thank you!
Cheers
socialdistortion said:
Good work @The_ERROR.
It should work. I think you should also add that the phone mode should be set to Emergency (and not DIAG as mentioned) in the kdz updater.
Click to expand...
Click to collapse
Good to know - do you know differences between CS_EMERGENCY and EMERGENCY?
Recovery Phone?!
Hello,
Had anyone tried "Recovery Phone" from the LGMobile Update app? It's under the "Customer Support" menu. Enter IMEI or S/N and see if it can bring it up to life.
Cheers.
Yes.. I tried.. but nothing.. the LG MOBILE UPDATE crashed because don't wiew the phone in Usb...
zeule said:
Hello,
Had anyone tried "Recovery Phone" from the LGMobile Update app? It's under the "Customer Support" menu. Enter IMEI or S/N and see if it can bring it up to life.
Cheers.
Click to expand...
Click to collapse
I can add that as next possible way Let me expect it.
batman89i said:
Yes.. I tried.. but nothing.. the LG MOBILE UPDATE crashed because don't wiew the phone in Usb...
Click to expand...
Click to collapse
So... it sad everything
The_ERROR said:
Good to know - do you know differences between CS_EMERGENCY and EMERGENCY?
Click to expand...
Click to collapse
Not really. Gathered some info though. We use emergency mode when the phone boots into only emergency mode else we try CS emergency as last option.
In any case this method will work only if the kdz updater recognises the phone.
Further reading http://android.modaco.com/content/lg-gt540-optimus-gt540-modaco-com/321895/faq-gt540-reference-thread/
I was able to do the KDZ, actually thats the only way possible. Please add this to the list:
1. Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments.
2. Install the LG drivers by selecting the update manager from the lg site.
3. Disable the modem driver.
4. Once done, reboot the handset and when it has come to emergency mode connect it via USB.
5. Its going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
6. shake the handset - IT DID WORKED FOR ME.
My suggestion don't give up. It took me around 14 hours to bring the handset back to original firmware and here I am today trying to boot the rom once again.
7. UPDATE AND ENJOY.
pariksheetsharma said:
I was able to do the KDZ, actually thats the only way possible. Please add this to the list:
1. Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments.
2. Install the LG drivers by selecting the update manager from the lg site.
3. Disable the modem driver.
4. Once done, reboot the handset and when it has come to emergency mode connect it via USB.
5. Its going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
6. shake the handset - IT DID WORKED FOR ME.
My suggestion don't give up. It took me around 14 hours to bring the handset back to original firmware and here I am today trying to boot the rom once again.
7. UPDATE AND ENJOY.
Click to expand...
Click to collapse
Thanks, I will do!! Only about 4 and five.
First reboot the handset and when it has come to emergency mode connect it via USB
and then
It's going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
So, whats about if phone didn't go into emrgency itself (for example stuck on Android logo)?
The_ERROR said:
Thanks, I will do!! Only about 4 and five.
First reboot the handset and when it has come to emergency mode connect it via USB
and then
It's going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
So, whats about if phone didn't go into emrgency itself (for example stuck on Android logo)?
Click to expand...
Click to collapse
I am talking about phone getting into Emergency mode, KDZ doesn't need to switch to CS_EMERGENCY or EMERGENCY Switch off the phone first, then you are either connect it to USB cable or you can remove it from the USB cable. Key combination to bring the phone only in emergency mode are:
1. Connected to USB cable, only thing visible is the LG logo, this is because its getting charged. Press VOL UP + BACK BUTTON
2. Not connected to USB cable and is not charging and so switched off: Press VOL UP + BACK BUTTON + POWER BUTTON
In both the cases phone will switch to a yellow screen showing: "Emergency mode!!" and will remain like that.
It's only in Emergency mode that the handset will be detected like a USB drive and can be KDZed.
I seriously doubt the "Shake your phone part". It just sounds so ...
Peace
pariksheetsharma said:
I am talking about phone getting into Emergency mode, KDZ doesn't need to switch to CS_EMERGENCY or EMERGENCY Switch off the phone first, then you are either connect it to USB cable or you can remove it from the USB cable. Key combination to bring the phone only in emergency mode are:
1. Connected to USB cable, only thing visible is the LG logo, this is because its getting charged. Press VOL UP + BACK BUTTON
2. Not connected to USB cable and is not charging and so switched off: Press VOL UP + BACK BUTTON + POWER BUTTON
In both the cases phone will switch to a yellow screen showing: "Emergency mode!!" and will remain like that.
It's only in Emergency mode that the handset will be detected like a USB drive and can be KDZed.
Click to expand...
Click to collapse
OK, I edited it. But I kept possibilities of EMERGENCY and CS_EMERGENCY modes if standard way failed. About switch into emergency, I think that it does not matter which way for emergency is used.
socialdistortion said:
I seriously doubt the "Shake your phone part". It just sounds so ...
Peace
Click to expand...
Click to collapse
Yes, I know... but if it will help, it doesn't matter how stupid it sounds....
Stuck in LG logo, unable to boot into emergency mode.
What can I do? Go to LG?
cjbi said:
Stuck in LG logo, unable to boot into emergency mode.
What can I do? Go to LG?
Click to expand...
Click to collapse
Have you tried all the mentioned methods? Press the combination buttons a little longer (Maybe that can help).
BTW what did you do that bricked your phone?
Hello,
- i'm the proud owner of an LG P500, i mannaged to "kill" it alot of times, one time i bricked it so bad the power button was useless. I'm going to tell you how i always manneged to fix it.
1. - install the USB DRIVERS for LG P500 Download LINK
2. - extract the KDZ archive , install msxml.msi, Download LINK, Download Froyo 2.2.2. v10E.kdz after that open >> KDZ_FW_UPD.exe, select type 3GQCT and mode DIAG (select this only if your phone starts when you connect the USB and the battery charging logo apears) if the phone starts in Emergency Mode or dosen't start at all >> remove battery and while holding the BACK and volume UP buttons connect the USB, the phone should start in Emergency Mode, after that select in KDZ, MODE > EMERGENCY, select file > V10E_00.kdz and press the "Launch software update" .
- wait for KDZ to do it's job ( until it says FINISHED) after it is finished it will reset the phone (alot of times the phone wolden't start after reset and i had to start it manualy @power button) an LG logo should apear , then an Android logo, wait about 5 - 10 min (the phone should start and you will have froyo 2.2.2. working), but if the Android LOGO stops or lags for 2,3 seconds then you must remove battery , put it back , and power on the phone. if it dose the same thing , then you must reflash your phone. Usualy it works with the battery on and simply flashing under DIAG mode.
- after reflashing if you have the same problem , you must remove battery and try installing it DIAG mode. if it still dosen't work enter emergency mode ( UP + BACK + connect USB (or press the power button)) and reflash using KDZ , MODE >>> EMERGENCY.
- when phone is connected go to COMPUTER > PROPERTIES > DEVICE MANAGER > MODEMS > and disable LGE Modem.. (some say it helps i diden't saw any difference.)
- as i was saying i killed my phone alot of times, KDZ always helped me bring it back to life , be patient.. and if you get alot of errors and flash meny times the phone gets hot , leave it to cool for a while and then try again.
be patient !! hope this will help you ..
sorry for my bad english !!
i dont mean to be rude, but there are guides on this already (i mean, how else would you know this yourself)
http://forum.xda-developers.com/showthread.php?t=1060121
http://forum.xda-developers.com/showthread.php?t=875881
sweetnsour said:
i dont mean to be rude, but there are guides on this already (i mean, how else would you know this yourself)
http://forum.xda-developers.com/showthread.php?t=1060121
http://forum.xda-developers.com/showthread.php?t=875881
Click to expand...
Click to collapse
- i understand, you'r right, but "I'm going to tell "you" how i always manneged to fix it."
PS: i wrote this tutorial after reading alot about unbricking , i tried to make it simple.
xzet2 said:
- i understand, you'r right, but "I'm going to tell "you" how i always manneged to fix it."
PS: i wrote this tutorial after reading alot about unbricking , i tried to make it simple.
Click to expand...
Click to collapse
what you posted is the exact same thing as what is posted in my links
okay , i diden't saw the detail'd tutorial with pictures , if this one is usless "someone" delete it.
no need delete
just edit ur thread with got solved or thread close something like this ~~
Thanks alot, dude. My phone is working again.
rainCz said:
Thanks alot, dude. My phone is working again.
Click to expand...
Click to collapse
well i think this one has helped someone
good luck
Bricked my phone beyond recovery
i totally bricked my phone, while i was using kdzupdater something went wrong . Finally had to go to the LG service center ( hope my warranty is not void in India). Well they said the phone is not responding to software it will need a new PCB. So my phone goes for like 2-3 days away from me.
As posted before, It's already been posted on here but great work nonetheless. It's better to have more posts like these then have more people posting about how to unbrick there phone.
Thanks for the post... I was a little unsure about flashing via KDZ, but this thread actually points few ways of procedure in case of things going wrong...
I think, this thread is pretty helpful and complements well with the others regular "how to" threads!
LG p500 Unbrick
Dear Sir,
I have lg p500, Yesterday i was downgrade my mobile software from 2.3.3 to 2.2 through KDZ updater. while updating error came finally my mobile now in dead condition, I tried to boot emergency mode (Volume UP+Back Button+USB Connect) there is no reaction on my mobile screen even though battery was removed.Any body help me to come back live my phone(I had lost my mobile purchase bill, if it is available i will give to LG service center)
xzet2 said:
Hello,
- i'm the proud owner of an LG P500, i mannaged to "kill" it alot of times, one time i bricked it so bad the power button was useless. I'm going to tell you how i always manneged to fix it.
1. - install the USB DRIVERS for LG P500 Download LINK
2. - extract the KDZ archive , install msxml.msi, Download LINK, Download Froyo 2.2.2. v10E.kdz after that open >> KDZ_FW_UPD.exe, select type 3GQCT and mode DIAG (select this only if your phone starts when you connect the USB and the battery charging logo apears) if the phone starts in Emergency Mode or dosen't start at all >> remove battery and while holding the BACK and volume UP buttons connect the USB, the phone should start in Emergency Mode, after that select in KDZ, MODE > EMERGENCY, select file > V10E_00.kdz and press the "Launch software update" .
- wait for KDZ to do it's job ( until it says FINISHED) after it is finished it will reset the phone (alot of times the phone wolden't start after reset and i had to start it manualy @power button) an LG logo should apear , then an Android logo, wait about 5 - 10 min (the phone should start and you will have froyo 2.2.2. working), but if the Android LOGO stops or lags for 2,3 seconds then you must remove battery , put it back , and power on the phone. if it dose the same thing , then you must reflash your phone. Usualy it works with the battery on and simply flashing under DIAG mode.
- after reflashing if you have the same problem , you must remove battery and try installing it DIAG mode. if it still dosen't work enter emergency mode ( UP + BACK + connect USB (or press the power button)) and reflash using KDZ , MODE >>> EMERGENCY.
- when phone is connected go to COMPUTER > PROPERTIES > DEVICE MANAGER > MODEMS > and disable LGE Modem.. (some say it helps i diden't saw any difference.)
- as i was saying i killed my phone alot of times, KDZ always helped me bring it back to life , be patient.. and if you get alot of errors and flash meny times the phone gets hot , leave it to cool for a while and then try again.
be patient !! hope this will help you ..
sorry for my bad english !!
Click to expand...
Click to collapse
Thank you for your information... Actually Today when i WAS UPDATING MY p500 FROM ROM 2.2.2 TO OFFICIAL 2.3 THROUGH KDZ,I got an error in the updating process, My phone shows only emergency mode... and after that i removed the battery and try to switch on the phone.. But my phone is seems totally dead.... I had also tried your procedure. But it wont work... Please help me how can I unbrick it..
Plz...plzz.plzzz.....
---------- Post added at 03:13 PM ---------- Previous post was at 03:08 PM ----------
sweetnsour said:
i dont mean to be rude, but there are guides on this already (i mean, how else would you know this yourself)
http://forum.xda-developers.com/showthread.php?t=1060121
http://forum.xda-developers.com/showthread.php?t=875881
Click to expand...
Click to collapse
Hello sir,
Thank you for your information... Actually Today when i WAS UPDATING MY p500 FROM ROM 2.2.2 TO OFFICIAL 2.3 THROUGH KDZ,I got an error in the updating process, My phone shows only emergency mode... and after that i removed the battery and try to switch on the phone.. But my phone is seems totally dead.... I had also tried your procedure. But it wont work... Please help me how can I unbrick it..
Plz...plzz.plzzz.....
i keep getting upgrade error
wparam:100
lparam: 502 ,
i have the optimus m , and when i connect it in emergency mode my computer AUTOMATICALLY says that there is a usb 2.0 slot avaible , and when i connect it to another it says the same thing , and i am positive that all my usbs are 2.0
Sent from my Mytouch 4G Running Capychimps Sense 3.5 rom (v.4.0)
and then KDZ force closes
Sent from my Mytouch 4G Running Capychimps Sense 3.5 rom (v.4.0)
also the phone unmounts (the screen flashes) every 25 seconds
Sent from my Mytouch 4G Running Capychimps Sense 3.5 rom (v.4.0)
---------- Post added at 04:34 PM ---------- Previous post was at 04:14 PM ----------
Heres my Log :
[16:30:43:509] : =============================================
[16:30:43:509] : Log is started on 06.01.2012, at 16:30:43:509,
executable: C:\Users\David\Desktop\KDZ_FW_UPD_EN\KDZ_FW_UPD.exe (ProcID: 0x00000a1c),
compile time : Dec 8 2010 09:19:37
[16:30:43:509] : Version :
[16:30:43:509] : Get Usb Port
[16:30:43:509] : rsi.strFriendlyName=LGE CDMA USB Serial Port (COM6)
[16:30:43:509] : FriendlyNameList[iii].szFriendlyName=LGE CDMA USB Serial Port
[16:30:43:509] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 1 - COM6
[16:30:43:509] : Port = COM6
[16:30:43:525] : UNKNOWN : Req(12) -> Rsp(13)
[16:30:48:548] : RX Timeout : 5.0 seconds
[16:30:48:548] : RX TIMEOUT
[16:30:48:564] : UNKNOWN : Req(12) -> Rsp(13)
[16:30:48:564] : >> DIAG_STATUS_F FAILED
[16:30:48:579] : >>Get Model Name [DIAG_VERNO_F]
[16:30:51:606] : RX Timeout : 3.0 seconds
[16:30:51:606] : RX TIMEOUT
[16:30:51:621] : BAD CONN MODE : Req(0) -> Rsp(3)
[16:30:54:648] : RX Timeout : 3.0 seconds
[16:30:54:648] : RX TIMEOUT
[16:30:54:663] : BAD CONN MODE : Req(0) -> Rsp(3)
[16:30:57:690] : RX Timeout : 3.0 seconds
[16:30:57:690] : RX TIMEOUT
[16:30:57:705] : BAD CONN MODE : Req(0) -> Rsp(3)
[16:30:57:705] : FAIL (No Phone)
[16:30:57:705] : GetModelName() Operation Failed Check Diag CMD
[16:30:57:705] : EMERGENCY Booting Mode
[16:30:57:705] : >>Get Model Name in Emergency Mode [DLOAD_VERREQ_F]
[16:30:57:721] : 76XXT-6040-TSNCJPLYMta\Local\Temp\DZE51
[16:30:57:721] : First two character of model name is not BS
[16:30:57:721] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 0 - No Phone
[16:30:57:721] : GetEmergencyModelName in Emergency Mode - FAILed (No Phone)
[16:30:57:721] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - Close Port
[16:30:57:721] : Close Port<<
[16:30:57:721] : TYPE_WPARAM_UPGRADE_ERROR
[16:30:57:752] : Log finished
then KDZ force closes .
;(
Yesterday, i've tried to go to recovery mode in powermenu [ROM CM7 nightly 1], but phone just stuck at lg logo. Then I've tried to unbrick it with KDZ. Something in first progress steps happened, and now my phone do not show any signs of life. Also I have no warranty.But i can fix it, i searched on every forum, and did not found anything, that would work. So is there any way i could unbrick my phone ?
Thanks
P.s.
And maybe i could fix it somehow using JTAG, but using arduino as that thing ? ( I don't have an arduino, but I am planing to have one)
It worked on my device , thank you:good:
xzet2 said:
Hello,
- i'm the proud owner of an LG P500, i mannaged to "kill" it alot of times, one time i bricked it so bad the power button was useless. I'm going to tell you how i always manneged to fix it.
1. - install the USB DRIVERS for LG P500 Download LINK
2. - extract the KDZ archive , install msxml.msi, Download LINK, Download Froyo 2.2.2. v10E.kdz after that open >> KDZ_FW_UPD.exe, select type 3GQCT and mode DIAG (select this only if your phone starts when you connect the USB and the battery charging logo apears) if the phone starts in Emergency Mode or dosen't start at all >> remove battery and while holding the BACK and volume UP buttons connect the USB, the phone should start in Emergency Mode, after that select in KDZ, MODE > EMERGENCY, select file > V10E_00.kdz and press the "Launch software update" .
- wait for KDZ to do it's job ( until it says FINISHED) after it is finished it will reset the phone (alot of times the phone wolden't start after reset and i had to start it manualy @power button) an LG logo should apear , then an Android logo, wait about 5 - 10 min (the phone should start and you will have froyo 2.2.2. working), but if the Android LOGO stops or lags for 2,3 seconds then you must remove battery , put it back , and power on the phone. if it dose the same thing , then you must reflash your phone. Usualy it works with the battery on and simply flashing under DIAG mode.
- after reflashing if you have the same problem , you must remove battery and try installing it DIAG mode. if it still dosen't work enter emergency mode ( UP + BACK + connect USB (or press the power button)) and reflash using KDZ , MODE >>> EMERGENCY.
- when phone is connected go to COMPUTER > PROPERTIES > DEVICE MANAGER > MODEMS > and disable LGE Modem.. (some say it helps i diden't saw any difference.)
- as i was saying i killed my phone alot of times, KDZ always helped me bring it back to life , be patient.. and if you get alot of errors and flash meny times the phone gets hot , leave it to cool for a while and then try again.
be patient !! hope this will help you ..
sorry for my bad english !!
Click to expand...
Click to collapse
after doing this my phone is not booting only
error with kdz
upgrade error
WParam : 100
LParam : 500
pls help me guys
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
This happened to me also. I solved it like this:
First thing to do is get sure the LG drivers are installed ( there is a topic in the forum on this also).
Install KDZ ( serch in the forum and download it)
Download a room ( stock or not )
Flash the phone with KDZ ( after the drivers have been installed the phone should be detected on the pc.
After flashing if it does not start up do not fear, get the battery out, re install the battery and do a hard reset power+home+volume down buttons pressed at the same time and it should work.
If its your first time install Stock GB 20E as it is an open room, if not new to this I would suggest CM7.
Hope it helped
Regards
But the PC doesn't recognize the phone.
Here is the log from KDZ:
[R&D Test Tools Log File]
23:47:37 : Launching SW update
23:47:37 : Unpacking KDZ
23:47:39 : KDZ file extraced
23:47:40 : Files were extracted.
23:47:40 : LGMobileDL Load.
23:47:40 : Port = -1
23:47:40 : Connecting to phone
23:47:40 : PHONE WAS NOT FOUND!
23:47:42 : ===FINISHED===
Click to expand...
Click to collapse
How should I solve this problem? :/
bondzi said:
But the PC doesn't recognize the phone.
Here is the log from KDZ:
How should I solve this problem? :/
Click to expand...
Click to collapse
I had this same issue too, do not worry.
Keep your phone plugged into your computer, and go to Start > Control Panel > System > Hardware > Device Manager > Modems and disable the LG modem.
I am on Windows XP, so it may not be the same steps, but the point is that you have to disable the LG modem in Device Manager.
I had the same problem as well at one point. What operating system are you running on your computer?
I had the same issue, but I could not find the LG modem to disable it, it was just that windows was not detecting my phone at all, or using the drivers I had installed for my P500 to figure out what was connected to my laptop. Bricked phone after a failed ROM flash. Reinstallation of USB drivers for my phone failed to do anything.
Have you used LG Mobile update at all? I got all my drivers through it, rather than useless PC Suite 4.
Download it through HERE
Here's what I did to rectify it (Running windows vista):
DO NOT PLUG IN YOUR PHONE UNTIL STEP 3!
1. Went to system restore in windows(you'll find it under Backup and Restore in the Control Panel) and restore your computer to a state before installing any drivers for your phone.
2. After everything had completed, installed LG Mobile update. There is an option to install general USB drivers for your phone, DO NOT do it! Go to Customer Support > Application, Manual & USB driver download. Input your IMEI number from behind the battery in the back of your phone(or just select the "Read your phone" option if you can get it to read your phone). It will search and return the correct drivers for your exact phone. Download and install your USB drivers.
3. Keep your phone disconnected from your PC, and start up LG mobile update again. Connect your phone, LG mobile update should verify the connection by trying to connect to your phone, checking software versions, etc. It will connect even if you are stuck at the LG screen.
4. If everything checks out run KDZ updater and flash your phone back to original specs.
hey first go to emergency mode by pressing back(return) and volume up
and then in emergency mode use kdz it then only pc will recongnise your phone
believe me this thing also happens with me and I know that time I very scared
that time I used this article
http://forum.xda-developers.com/showthread.php?t=1015332
bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
read general thread it has been answered many times,stucking at lg logo is solved by take out battery reinsert and the 3 button combo
have u tried HOME + VOL DOWN +POWER BUTTON,still if it dont,
read downgrading details here http://forum.xda-developers.com/showthread.php?t=1038338
error guide here http://forum.xda-developers.com/showthread.php?t=883314
The same problem. But i solved it.
1) install again the driver using B2CAppSetup
2)This is based by xda forum by: Zecanills with a detailed explanation from my side.
- You need to download the firmware of your device. Download "Orginal LG Firmware" application (search in xda forum). Open it, put your IMEI and you will download the original ROM.
- Download KDZ updater and uncompress it
KDZ_FW_UPD_EN.zip - 4shared.com - online file sharing and storage - download
- Install msxml.msi from the uncompressed directory
3) Remove the battery, put it back and start the phone in emergency mode (actually the only way possible) back+up volume+power
Connect your device and run KDZ_FW_UPD.exe (as administrator). If the phone is not recognized repeat step 3) several times.
Select Type : 3GQCT
Select PhoneMode : DIAG
In KDZ file : Choose the ROM file you downloaded in the step 2)
Press Launch software update and wait (It will be 10 minutes or so).
Wait until it reboots.
After reboot will appear an image as in the following link: http://androidforums.com/getitnowmarketing/330813-all-one-recovery-thread.html
Don't worry. Restart phone again pushing power button (or remove battery, put it back and push power ) and then after few minutes you will have the phone as the begging when you bought it.
Thanks people for helping me. I just put the phone in emergency mode (Volume UP button + Home button), connected to the PC and flashed with KDZ.
After that, the phone works fine.
Thank you again!
bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp
LG P925
Same thing happened to me! I'm desperate... I've done research for hours and tried everything but no success so far... anyone could help us?
88prince said:
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp
Click to expand...
Click to collapse
hi guys I'm new in the forum,
I have a problem whith my LG F60(D390N) , it's bricked,(I had installed the wrong custom ROM) now I can't go to recovery or download mode ,
the phone don't start up , (there's no problem whith the battery or charger,
when I connect the phone to the PC i see only QHSUSB_BULK, please guys help me :crying: ,
the assistence it's very expensive.
Im in the same boat.
Installed first a stock 5.0.1 over the kitkat, everithyng went fine but after that installd a wrong CWM recovery
Now when I turn on my phone, its vibrate infinitely, and nothing happen. Black screen. When I put in-out-in my usb cable, screen turns on, and phone says: DBI Apps Watchdog Reset!
DemiGod Crash Handler : DBI Apps Watchdog Reset!
Please do following action.
1) Dload Mode. Please connect USB.
2) Get the ram dump image using QPST Configuration.
----------------------------------------------------------------------------
Board Info
rev. : 1.1, serial : 003bwff********
secure boot : disabled
--------------------------------------------------------------------------
Jump to Dload Mode.
I have no idea how I can take it back into life :S
I find it in device manager at COM ports : LGE AndroidNet USB Serial Port (COM6)
and at modems : LGE AndroidNet USB Modem
Hi everybody today i wanted to hard reset my XPERIA because i have an error with WIFI (0x) and it's disconnect after 2 secondes of internet
I connect my phone into USB (Power ON with USB debug) nothing hapenning only charge
I try to access to Fastboot (Green Light and black screen + error on windows) the error is : usb not recognized (Error 43)
Flashboot and Sony companion won't detect my phone i'm lost i don't have idea what i do now
Thanks for reply !
I found i how to solve this :
Step 1 : Put an headset in the jack prise
Step 2 : Hard reboot your phone with the small hole
Step 3 : Use your xperia normally
Step 4 : Wait for the battery to 5% (minimum)
Step 5 : Put your phone in the usb cable and your pc configure the USB and you can use without problem your phone
I hope it's working for you, but for me it's worked.
xC3Dr1C said:
Hi everybody today i wanted to hard reset my XPERIA because i have an error with WIFI (0x) and it's disconnect after 2 secondes of internet
I connect my phone into USB (Power ON with USB debug) nothing hapenning only charge
I try to access to Fastboot (Green Light and black screen + error on windows) the error is : usb not recognized (Error 43)
Flashboot and Sony companion won't detect my phone i'm lost i don't have idea what i do now
Thanks for reply !
Click to expand...
Click to collapse
try different usb cable
abodoma said:
try different usb cable
Click to expand...
Click to collapse
Tried 4 diffferent usb cable no change :/
I found i how to solve this :
Step 1 : Put an headset in the jack prise
Step 2 : Hard reboot your phone with the small hole
Step 3 : Use your xperia normally
Step 4 : Wait for the battery to 5% (minimum)
Step 5 : Put your phone in the usb cable and your pc configure the USB and you can use without problem your phone
I hope it's working for you, but for me it's worked.