I followed these instructions only: http://forum.xda-developers.com/showpost.php?p=35603363&postcount=3
I ignored the warning about needing to flash a stock rom as I couldn't see the point of flashing something which is already on the device.
When in Odin mode, it says:
Code:
PRODUCT NAME: GT-S5830i
CUSTOM BIN DOWN: NO(0 counts)
CURRENT BIN:SAMSUNG OFFICIAL
With the phone in ODIN mode, plugging the device into my Linux PC comes up with USB errors much like the following:
Code:
[ 255.706655] usb 2-4: new high-speed USB device number 3 using ehci_hcd
[ 255.938608] cdc_acm 2-4:1.0: This device cannot do calls on its own. It is not a modem.
[ 255.938695] cdc_acm 2-4:1.0: ttyACM0: USB ACM device
[ 257.364592] usb 2-4: USB disconnect, device number 3
[ 257.369128] usbcore: registered new interface driver cdc_acm
[ 257.369131] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 259.203322] usb 2-2: new high-speed USB device number 4 using ehci_hcd
[ 259.503540] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 259.759984] usb 6-2: new full-speed USB device number 2 using uhci_hcd
[ 274.866657] usb 6-2: device descriptor read/64, error -110
[ 290.076652] usb 6-2: device descriptor read/64, error -110
[ 290.286648] usb 6-2: new full-speed USB device number 3 using uhci_hcd
[ 305.393317] usb 6-2: device descriptor read/64, error -110
[ 320.603315] usb 6-2: device descriptor read/64, error -110
[ 320.813321] usb 6-2: new full-speed USB device number 4 using uhci_hcd
[ 322.439979] usb 6-2: device not accepting address 4, error -71
[ 322.493336] hub 6-0:1.0: unable to enumerate USB device on port 2
Ordinarily, I use Odin within a VirtualBox Vista install, but as Linux is reporting the problem, that renders VirtualBox useless. I don't really want to re-install Vista on my PC, as it will mean a lot of hard drive partition shuffling including deletion of one of my Linux installs just to make room for a Windows install which I'll very rarely use.
Code:
[[email protected] ~]$ uname -a
Linux Scrapyard 3.7.10-1-ARCH #1 SMP PREEMPT Thu Feb 28 09:50:17 CET 2013 x86_64 GNU/Linux
A few questions first:
1) Any Linux users solved this without using Windows?
2) Might I find after installing Windows, that the problem is not with Linux?
3) Is there some other way of reseting the phone?
Thanks for any help.
Have you even installed the USB drivers?
Android-fany said:
Have you even installed the USB drivers?
Click to expand...
Click to collapse
Which USB drivers would they be? I'm not being funny, but have you even read the title? I'm using Linux. I don't need to install USB drivers.
#edit2
At least, I don't need to install USB drivers for any device which operates in mass storage mode, which was what the device was operating in before I bricked it.
I don't know what protocol the device operates in when in Download Mode... it wouldn't be Media Transfer Protocol (MPT) by any chance?
I followed these instructions for my Galaxy Tab 2.0
wiki.archlinux.org index.php/MTP
Might be worth a try... will report back...
sirromj said:
Which USB drivers would they be? I'm not being funny, but have you even read the title? I'm using Linux. I don't need to install USB drivers.
Click to expand...
Click to collapse
Sorry, but I don't know much about Linux. So I am just asking if there are USB drivers on Linux. So, sorry.
Android-fany said:
Sorry, but I don't know much about Linux. So I am just asking if there are USB drivers on Linux. So, sorry.
Click to expand...
Click to collapse
Ok no problem.
Decided MTP has nothing to do with this at all, definitely barking up the wrong tree there.
Tried it in Windows Vista now. I have Kies installed. Windows does not recognize the device, it says the device malfunctioned... Vista installs some USB driver for the device, but it's still an unknown device. Odin does not recognize the device.
The device won't boot into recovery mode.
The device won't boot past the Samsung Galaxy Ace GT-S5830i screen.
Is there anything else I can do to get it working again?
sirromj said:
Tried it in Windows Vista now. I have Kies installed. Windows does not recognize the device, it says the device malfunctioned... Vista installs some USB driver for the device, but it's still an unknown device. Odin does not recognize the device.
The device won't boot into recovery mode.
The device won't boot past the Samsung Galaxy Ace GT-S5830i screen.
Is there anything else I can do to get it working again?
Click to expand...
Click to collapse
download odin maybe?
sirromj said:
Tried it in Windows Vista now. I have Kies installed. Windows does not recognize the device, it says the device malfunctioned... Vista installs some USB driver for the device, but it's still an unknown device. Odin does not recognize the device.
The device won't boot into recovery mode.
The device won't boot past the Samsung Galaxy Ace GT-S5830i screen.
Is there anything else I can do to get it working again?
Click to expand...
Click to collapse
Try on other pc.
Sent from my GT-S5830i using xda premium
sirromj said:
Tried it in Windows Vista now. I have Kies installed. Windows does not recognize the device, it says the device malfunctioned... Vista installs some USB driver for the device, but it's still an unknown device. Odin does not recognize the device.
The device won't boot into recovery mode.
The device won't boot past the Samsung Galaxy Ace GT-S5830i screen.
Is there anything else I can do to get it working again?
Click to expand...
Click to collapse
GermainZ may help you
Try to contact him
Ynt: [Q] First flash fail + Linux USB errors
sirromj said:
Tried it in Windows Vista now. I have Kies installed. Windows does not recognize the device, it says the device malfunctioned... Vista installs some USB driver for the device, but it's still an unknown device. Odin does not recognize the device.
The device won't boot into recovery mode.
The device won't boot past the Samsung Galaxy Ace GT-S5830i screen.
Is there anything else I can do to get it working again?
Click to expand...
Click to collapse
First remove and select delete drivers from Device Manager in control panel. Then remove cable from usb port. Install the drivers dont connect cable. Reboot computer. Take battery out. When pc fully boots plug cable to phone. Enter odin mode (vol up + vol down + power). When you see warning screen immediately plug cable to pc in other usb port. Select odin mode in phone and wait drivers to recognized. Open odin to see if com port installed. Then flash one of the original firmwares.
S5830i Stock + Root + init.d + LightSpeed Intervention + Link2SD
I forgot to ask, have you enable usb debugging in your phone?
Sent from my GT-S5830i using xda premium
ChelebiTech said:
First remove and select delete drivers from Device Manager in control panel. Then remove cable from usb port. Install the drivers dont connect cable. Reboot computer. Take battery out. When pc fully boots plug cable to phone. Enter odin mode (vol up + vol down + power). When you see warning screen immediately plug cable to pc in other usb port. Select odin mode in phone and wait drivers to recognized. Open odin to see if com port installed. Then flash one of the original firmwares.
Click to expand...
Click to collapse
Hi ChelebiTech, thanks for replying. Taken me a long time to get around to doing this, partly because I really really really did not expect that to work. But unbelievably it did, and my gt-s5830i is now recognized by Odin v3.0.7. Good stuff.
However, I'm really struggling to navigate my way around all the available information on here. I don't know if I should first try flashing a new recovery, because I cannot enter recovery mode, or try flashing a stock firmware.
I've been looking at flashing the stock firmware but I can't find any exact firmware matches from the details I've written down before my failed flash attempt.
I wrote down:
Sales Code: BTU
PDA:S5830iXXLD3
PHONE:S5830iXXLD2
CSC:S5830iBTULC1
Using the firmware checker on samsmobiles.com, the closest match I find is
PDA:S5830IXXLK3
CSC:S5830IBTULK1
MODEM:S5830IXXLK1
As far as flashing a recovery goes, what are my choices if I can't use any recovery mode in the first place? Is there a recovery I can flash?
Thanks for any help.
sirromj said:
I've been looking at flashing the stock firmware but I can't find any exact firmware matches from the details I've written down before my failed flash attempt.
I wrote down:
Sales Code: BTU
PDA:S5830iXXLD3
PHONE:S5830iXXLD2
CSC:S5830iBTULC1
Using the firmware checker on samsmobiles.com, the closest match I find is
PDA:S5830IXXLK3
CSC:S5830IBTULK1
MODEM:S5830IXXLK1
As far as flashing a recovery goes, what are my choices if I can't use any recovery mode in the first place? Is there a recovery I can flash?
Thanks for any help.
Click to expand...
Click to collapse
Ah sorry, Vista/Internet-Explorer is all a bit strange to me, back in Linux and I suddenly can find the matching firmware: http://www.sammobile.com/firmwares/1/?model=GT-S5830i&pcode=BTU#firmware
[SOLVED] First flash fail + Linux USB errors
sirromj said:
Ah sorry, Vista/Internet-Explorer is all a bit strange to me, back in Linux and I suddenly can find the matching firmware: http://www.sammobile.com/firmwares/1/?model=GT-S5830i&pcode=BTU#firmware
Click to expand...
Click to collapse
Flashing the above in Odin V 3.0.7 and the phone is back, hurrah! :victory::victory::victory::victory::victory::victory:
I thought only Odin 1.85/1.87 were compatible with this phone.
Sent from my GT-S5830M
atometros said:
I thought only Odin 1.85/1.87 were compatible with this phone.
Sent from my GT-S5830M
Click to expand...
Click to collapse
No, Odin v3.07 is compatible for us too.
Hello
I've got Lark Freeme 70.65, it's a cheap tablet based on Allwinner A13 procesor. It was allright till yesterday. I installed here CWM and Cyanogenmod 10.1 from there and it still was allright. But then suddenly, when I tried to replace camera drivers, everything collapsed, touchscreen is completely reversed in Y axis and it ain't got it's full range, so it was completely unaccesible. But it wasn't so bad, I did recovery of my stock rom from CWM mod, then once again installed cyanogenmod 10.1 and I did few experiments. It was nothing that would really hurt it, but I was so unlucky than in one moment every one way of access to the tablet failed. So right now I cannot use USB connection in any way, CWM when I try to recovery says about 'MD5 mismatch' (I haven't touched clockworkmod folder at all!) and I have touchscreen that is responding but is completely unusable.
Of course I tried different USB cable, different computer, different system and everything. lsusb can't see device at all, so do ADB. dmesg says this:
Code:
[91554.840089] usb 4-6: new high-speed USB device number 10 using ehci-pci
[91554.984872] usb 4-6: New USB device found, idVendor=18d1, idProduct=0003
[91554.984881] usb 4-6: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[91554.984885] usb 4-6: Product: Android
[91554.984888] usb 4-6: Manufacturer: USB Developer
[91554.984892] usb 4-6: SerialNumber: 200804116426ef0
[91554.985969] usb-storage 4-6:1.0: USB Mass Storage device detected
[91554.986928] scsi8 : usb-storage 4-6:1.0
[91555.561110] usb 4-6: USB disconnect, device number 10
so it connects disconnects immediately after plugging the usb cable.
It would be great if I only could restore touchscreen or usb connection. I thought that replacing the rom would help, but CWM can restore them only from zips, and I have only imgs and I haven't found any way to do this.
I'm starting to accept my sytuation, this device was very cheap (170 PLN, it should be about $60), but it would be a great experience and happines for me to repair it. If anyone have got his own lark freeme 70.65 backup from CWM or any other Allwinner A13 and could upload this for me, I could try it out from any SD card (sadly I lost my own backup). Any other propositions also in common.
flashed new rom with sad consequesces. Unable to get tab out of booting recovery kernal image. unable to reconnect to tablet as it show usb not recognized. have updated usb files with naked usb zip and also new fv flash files. still not getting anywhere. I have tried to flash recovery at apx but not working. Is there any hope or have I created a true brick/
Is your PC recognizing the gTab in APX mode (Power and Vol [-])? Does nvflash complete? Post screenshots.
usb not recognized
rajeevvp said:
Is your PC recognizing the gTab in APX mode (Power and Vol [-])? Does nvflash complete? Post screenshots.
Click to expand...
Click to collapse
usb not recognized, tablet goes into apx but the computer does not recognize it. I have tried several different driver combinations and it still cant' see it. I think that I somehow screwed up the driver in the tablet. but can't even get it to connect to the computer. I tried a linux connection and it didn't recognize it either. I was using a live cd and tried to get the startup to locate a driver, no such luck. Is there a way I can completly format the tablet??? I can't get it past the boot loader error. thanks for your input up to now. hope someone has answers for me. I may have created a very nice parts machine.
mfmmetz said:
I think that I somehow screwed up the driver in the tablet.
Click to expand...
Click to collapse
You can't screw-up the APX-mode USB driver on the gTablet--it's built into the system firmware --ie. it's hard-coded. A HW error is a more likely culprit (if, indeed, the PC doesn't see the tablet in APX mode) . Disassemble the gTab and carefully inspect the USB port and surroundings for stray bits of metal, or solder, or cut traces, etc.
I tried a linux connection and it didn't recognize it either. I was using a live cd and tried to get the startup to locate a driver, no such luck.
Click to expand...
Click to collapse
Since you can use Linux, do this:
1. Boot into Linux.
2. Put the tablet into APX mode (the screen will turn off).
3. Plug the cable from the tablet into the PC.
4. Run these command (only the stuff in bold) and post their output (or a screenshot):
Code:
$ [B]dmesg | tail -n20[/B]
...
[ 7872.447589] usb 1-2.2: new full-speed USB device number 8 using ohci_hcd
[ 7872.552503] usb 1-2.2: New USB device found, idVendor=[B]0955[/B], idProduct=[B]7820[/B]
[ 7872.552514] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7872.552521] usb 1-2.2: Product: APX
[ 7872.552528] usb 1-2.2: Manufacturer: NVIDIA Corp.
$ [B]lsusb
[/B]...
Bus 001 Device 008: ID [B]0955:7820 NVidia Corp.[/B]
...
$
I can't get it past the boot loader error.
Click to expand...
Click to collapse
Take a snap and post it.
Hello,
I'm trying to do a nvflash backup of my Prime to avoid bricks, but I can't connect it with APX nor in Windows neither in Linux.
In Linux I obtain this, and the device is not connected:
[ 170.990681] usb 2-1.2.1.2: new high-speed USB device number 17 using ehci-pci
[ 176.064021] usb 2-1.2.1.2: device descriptor read/64, error -71
Click to expand...
Click to collapse
In Windows the device still as Unknown Device even when I've installed the Naked Driver.
I've try in several PCs, in all USB ports, even with a powered hub, with the same results.
Any idea, please?
Linux Debian x64 and Windows 7 x64
Thanks!
Got a used G5 (H860), the USB port doesn't work, cannot be recognized by Windows, even in download mode, shows as "Unknown USB Device (Device Descriptor Request Failed) with Hardware ID "USB\DEVICE_DESCRIPTOR_FAILURE".
Tried different "chins".
Any idea/solution?
Cheers.