[Q] brick? Galaxy S3 - Galaxy S III Q&A, Help & Troubleshooting

Hi everyone , I need your help.
This morning I rebooted the phone itself and got stuck on the boot logo Galaxy SIII . I use CM 11, one of the last nightly. I can get into CWM ( v.6.0.4.3 ) and into DOWNLOAD mode.
After reboot CWM writes :
E: Can not mount / cache / recovery / command
E: Can not mount / cache / recovery / log
E: Can not open / cache / recovery / log
E: Can not mount / cache / recovery / last_log
E: Can not open / cache / recovery / last_log
I tried to wipe data / factory reset + wipe cache + wipe Dalvik and nothing. I tried to install a new rom via CWM nothing. Installation via ODIN also see nothing = FAIL screen . I tried original ROM I9300XXUGMJ9_I9300VFGGMJ5_I9300BUUGMJ3_HOME.tar.md5
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Odin writes :
<ID:0/007> Added !
<OSM> Enter CS for MD5 ..
<OSM> Check MD5 .. Do not unplug the cable ..
<OSM> Please wait ..
<OSM> I9300XXUGMJ9_I9300VFGGMJ5_I9300BUUGMJ3_HOME.tar.md5 is valid .
<OSM> Checking MD5 finished Sucessfully ..
<OSM> Leave CS ..
<ID:0/007> Odin v.3 engine (ID : 7 ) ..
<ID:0/007> File analysis ..
<ID:0/007> SetupConnection ..
<ID:0/007> Initialzation ..
<ID:0/007> Get PIT for mapping ..
<ID:0/007> Firmware update start ..
<ID:0/007> boot.img
<ID:0/007> NAND Write Start !
<ID:0/007>
<ID:0/007> Complete ( Write) operation failed .
<OSM> All threads completed. ( succeed 0 / failed 1 )
Please any advice.

---

Not good, sounds like nand failure. Try the rescue firmware in general forum, follow the instructions exactly as it includes a pit file.
Sent from my GT-I9300 using Tapatalk

---

I use this http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 RESCUE FIRMWARE SGSIII I9300, but it did not help.
Odin show this:

---

Sorry, new motherboard required. Warranty should cover if still available and flash counter is zero.
Sent from my GT-I9300 using Tapatalk

---

boomboomer said:
Sorry, new motherboard required. Warranty should cover if still available and flash counter is zero.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
Warranty is still valid, but my counter flash is 13. How it reset in this case?

---

Not possible in this case, triangle away runs from inside the rom.
Sent from my GT-I9300 using Tapatalk

---

And via ADB? I find this:
Here are the commands to reset the flash counter.
adb shell
su
echo -n '\x00' | dd obs=1 count=1 seek=4193796 of=/dev/block/mmcblk0
The '\x00' portion tells it to reset to to 0.
I try this via ADB and dont work...

---

ORBITH said:
And via ADB? I find this:
Here are the commands to reset the flash counter.
adb shell
su
echo -n '\x00' | dd obs=1 count=1 seek=4193796 of=/dev/block/mmcblk0
The '\x00' portion tells it to reset to to 0.
I try this via ADB and dont work...
Click to expand...
Click to collapse
Of course it doesn't since you have no working ROM with USB debugging enabled. Yesterday I learned that philz recovery provides ADB access from recovery, try to flash that one: http://forum.xda-developers.com/galaxy-s3/orig-development/i93xx-philz-touch-t2002953
Also try to flash stock recovery and perform format /data/ and factory reset. Sometimes stock recovery manages to fix this issue.