S3 freezes on start screen showing Samsung galaxy SIII GT-I9300 ,when I tried recovery mode it shows “ cannot mount flash, system or cache”, it can go to download mode ,tried to flash is using ODIN it fails showing below
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNB6_I9300OJVGNB3_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> sboot.bin
<ID:0/011> NAND Write Start!!
<ID:0/011> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Please advise how to fix it.
Try the rescue firmware from general forum, if that fails then your emmc chip is toast -new motherboard required.
Sent from my GT-I9300 using Tapatalk
Galaxy S3 Freezing
boomboomer said:
Try the rescue firmware from general forum, if that fails then your emmc chip is toast -new motherboard required.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
=======================================================
I tried using below package which includes below files with Odin3_v3.04
4.1.2 GT-I9300XXEMG4_KOR_MULTI_FACTORY
BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5
CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5
CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5
MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5
mx.pit
I got below!
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011>
<ID:0/011> Re-Partition operation failed.
<ID:0/011> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Is there any other way to make it work?
No, your emmc is blown.
Sent from my GT-I9300 using Tapatalk
try without using pit
Related
Hi guys!
My i9300 does not boot and instead keeps displaying the samsung logo. It doesn't enter the recovery mode either, but does enter the download mode. So I tried flashing 2 different official ROMs but I'm getting the error:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXEEMH1_SER_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I downloaded the ROM here:
<tried posting a link but was not allowed>
Could you please help me with this problem?
Thanks in advance!
Try another version of odin, different lead, port or pc. Ensure kies is not running. Follow the guide on flashing to the letter.
Download the rom from sammobile and check the md5.
Sent from my GT-I9300 using Tapatalk
wicccked said:
Hi guys!
My i9300 does not boot and instead keeps displaying the samsung logo. It doesn't enter the recovery mode either, but does enter the download mode. So I tried flashing 2 different official ROMs but I'm getting the error:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXEEMH1_SER_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I downloaded the ROM here:
<tried posting a link but was not allowed>
Could you please help me with this problem?
Thanks in advance!
Click to expand...
Click to collapse
I had a similar issue a while ago but it turned out to be an issue with the Kernel not being compatable with the Rom I flashed. I thought I had bricked it, until I flashed a stock kernal first then the stock ROM and it fixed it for me and it really does sound like you have the same issue, As for the rom not flashing its most likely a bad download try sammobile! let me know if it was the kernal!
jaggythistle said:
I had a similar issue a while ago but it turned out to be an issue with the Kernel not being compatable with the Rom I flashed. I thought I had bricked it, until I flashed a stock kernal first then the stock ROM and it fixed it for me and it really does sound like you have the same issue, As for the rom not flashing its most likely a bad download try sammobile! let me know if it was the kernal!
Click to expand...
Click to collapse
jaggythistle, thank you for the answer.
I downloaded the stock kernel, successfully flashed it, downloaded the matching ROM (1-file this time), but now when trying to flash I'm getting the following error:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBEMH3_I9300UBEMH1_I9300ECOEMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
What can I do?
boomboomer, Thanks for the reply. I have checked it all, now I'm getting the above error.
If you've tried all the connection issues then it appears your recovery positron is corrupt and can't be written. A rescue firmware, including pit might help but otherwise you'll need a new motherboard.
Search in general forum for the rescue firmware thread, follow the instructions.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
If you've tried all the connection issues then it appears your recovery positron is corrupt and can't be written. A rescue firmware, including pit might help but otherwise you'll need a new motherboard.
Search in general forum for the rescue firmware thread, follow the instructions.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
I have tried the rescue firmware and got the following error:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXEEMH1_SER_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
PIT damaged new motherboard .
You can search for this thread where a claim was made to fix pit .
(SOLVED) PIT/Bricked/Dead problem on GT-I9300 international
Worth trying before buying a new motherboard as you have no warranty .
JJEgan said:
PIT damaged new motherboard .
You can search for this thread where a claim was made to fix pit .
(SOLVED) PIT/Bricked/Dead problem on GT-I9300 international
Worth trying before buying a new motherboard as you have no warranty .
Click to expand...
Click to collapse
Tried it, Odin was hanging at the "Erase..." step for ~5-10 mins, then I got the error:
Code:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Erase...
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hi
when i try flash E210K to 4.3 stock firmware phone stuck at Sboot.bin file..now phone in download mode only
is there any solution for this>
<ID:0/051> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> E210KKKUGNA3_E210KKTTGNA3_E210KKKNA3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/051> Odin v.3 engine (ID:51)..
<ID:0/051> File analysis..
<ID:0/051> SetupConnection..
<ID:0/051> Initialzation..
<ID:0/051> Get PIT for mapping..
<ID:0/051> Firmware update start..
<ID:0/051> sboot.bin
<ID:0/051> NAND Write Start!!
<ID:0/051>
<ID:0/051> Complete(Write) operation failed.
<ID:0/051> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Thank you
Up this thread ..
E210K is the Korean variant of the s3, are you sure this is the model number of your phone? Flashing the wrong ROM will cause a brick because the partitions can be mounted differently
Sent from my GT-I9300 using Tapatalk
hello,
I just try my Tab2 also to flash. I get always the flash process via odin following message:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-P5110_CWM_6.0.5.1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Can anybody help me?
Greetings Coldjack
coldjack said:
hello,
I just try my Tab2 also to flash. I get always the flash process via odin following message:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-P5110_CWM_6.0.5.1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Can anybody help me?
Greetings Coldjack
Click to expand...
Click to collapse
It might be the same mistake I made when flashing my phone.. I didn't run Odin as administrator in win7. After I did run it as administrator the error was gone.
But.... I also had a similar error with bad files so it could be that too.
Sent from my GT-P7510 using XDA Free mobile app
Hi, l made it as Administrator.
And there comes the error.
Greetings coldjack
Hi,
I want to flash a stock firmware by Odin, and I need to do it with Re-partition. Is very important to do it because my tablet stuck in bootloop and only setting PIT file can make me come through SAMSUNG title.
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin engine v(ID:3.1301)..
<ID:0/010> File analysis..
<ID:0/010> Total Binary size: 3325 M
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Set PIT file..
<ID:0/010> DO NOT TURN OFF TARGET!!
<ID:0/010> FAIL!
<ID:0/010>
<ID:0/010> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
There you have a log from Odin and also I have a incorrect PIT file the firmware i want to flash is - T555XXS1BPL4_T555XEO1BPE2_T555XXU1BPD7_HOME.tar.md5
Thanks for all good people wants to help me
I try to flash G965U1UES2ARF4_CL13087505_QB18460747 in odin patched but no sucess
LOG ODIN
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:1/007> Added!!
<ID:0/011> Odin engine v(ID:3.1301)..
<ID:1/007> Odin engine v(ID:3.1301)..
<ID:0/011> File analysis..
<ID:1/007> File analysis..
<ID:0/011> skip file list for home binary
<ID:1/007> skip file list for home binary
<ID:0/011> apdp.mbn
<ID:1/007> apdp.mbn
<ID:0/011> msadp.mbn
<ID:1/007> msadp.mbn
<ID:0/011> persist.img.ext4
<ID:1/007> persist.img.ext4
<ID:0/011> userdata.img.ext4
<ID:1/007> userdata.img.ext4
<ID:0/011> dqmdbg.img.ext4
<ID:1/007> dqmdbg.img.ext4
<ID:0/011> Home Binary Download
<ID:1/007> Home Binary Download
<ID:0/011> Total Binary size: 4754 M
<ID:1/007> Total Binary size: 4754 M
<ID:0/011> SetupConnection..
<ID:1/007> SetupConnection..
<ID:1/007> Initialzation..
<ID:1/007> Get PIT for mapping..
<ID:1/007> Firmware update start..
<ID:1/007> NAND Write Start!!
<ID:1/007> SingleDownload.
<ID:1/007> abl.elf
<ID:1/007> FAIL! (Auth)
<ID:1/007>
<ID:1/007> Complete(Write) operation failed.
<ID:1/007> Removed!!
<ID:0/011> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 2)
my firmware from mine s9+ is on Screenshot to compare
Some help please
I want to know if this can be done without flashing or rooting. Maybe by using Knox and a Dev key.
d3vilh4ck3r said:
I try to flash G965U1UES2ARF4_CL13087505_QB18460747 in odin patched but no sucess
LOG ODIN
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:1/007> Added!!
<ID:0/011> Odin engine v(ID:3.1301)..
<ID:1/007> Odin engine v(ID:3.1301)..
<ID:0/011> File analysis..
<ID:1/007> File analysis..
<ID:0/011> skip file list for home binary
<ID:1/007> skip file list for home binary
<ID:0/011> apdp.mbn
<ID:1/007> apdp.mbn
<ID:0/011> msadp.mbn
<ID:1/007> msadp.mbn
<ID:0/011> persist.img.ext4
<ID:1/007> persist.img.ext4
<ID:0/011> userdata.img.ext4
<ID:1/007> userdata.img.ext4
<ID:0/011> dqmdbg.img.ext4
<ID:1/007> dqmdbg.img.ext4
<ID:0/011> Home Binary Download
<ID:1/007> Home Binary Download
<ID:0/011> Total Binary size: 4754 M
<ID:1/007> Total Binary size: 4754 M
<ID:0/011> SetupConnection..
<ID:1/007> SetupConnection..
<ID:1/007> Initialzation..
<ID:1/007> Get PIT for mapping..
<ID:1/007> Firmware update start..
<ID:1/007> NAND Write Start!!
<ID:1/007> SingleDownload.
<ID:1/007> abl.elf
<ID:1/007> FAIL! (Auth)
<ID:1/007>
<ID:1/007> Complete(Write) operation failed.
<ID:1/007> Removed!!
<ID:0/011> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 2)
my firmware from mine s9+ is on Screenshot to compare
Some help please
Click to expand...
Click to collapse
Do you have the Samsung USB drivers installed on your computer? Was the phone in download mode? It says it can't open the com port. Signs point to a communications issue, which is usually the lack of proper driver.
It can be done so easily by GSM tool i can help you about it
mambonike said:
It can be done so easily by GSM tool i can help you about it
Click to expand...
Click to collapse
How???
CrazyApe18 said:
Do you have the Samsung USB drivers installed on your computer? Was the phone in download mode? It says it can't open the com port. Signs point to a communications issue, which is usually the lack of proper driver.
Click to expand...
Click to collapse
Yes i have the Samsung USB drivers...
And yes the phone is in download mode.
d3vilh4ck3r said:
Yes i have the Samsung USB drivers...
And yes the phone is in download mode.
Click to expand...
Click to collapse
I feel kind of silly not to notice this before. But are you really in Lisbon as your profile and phone suggest? Are you sure you don't have an F model phone? Anyway, sorry, I don't know what else could be wrong.
CrazyApe18 said:
I feel kind of silly not to notice this before. But are you really in Lisbon as your profile and phone suggest? Are you sure you don't have an F model phone? Anyway, sorry, I don't know what else could be wrong.
Click to expand...
Click to collapse
yes i´m sure... my phone is G965U T-mobile from USA
And yes i´m portuguese from Lisbon
E sim sou de Lisboa e português
I have the same problem. PLUS GSM Poland - Flash Odin new official firmware XEO but when phone on/off always see screensplash. Maybe youy have got solution?
I got this on download mode
sw rev check fail [abl]fused 3 > binary 2
i thing is the wrong firmware
Mine phone S9+ SM-965U - G965USQ3ARG7
i want to update to G965U1
what is the best firmware?
d3vilh4ck3r said:
I got this on download mode
sw rev check fail [abl]fused 3 > binary 2
i thing is the wrong firmware
Mine phone S9+ SM-965U - G965USQ3ARG7
i want to update to G965U1
what is the best firmware?
Click to expand...
Click to collapse
You're trying to downgrade your bootloader. That is impossible on this phone. You're stuck with U firmware until a bootloader v3 firmware comes out for U1.
ya i know
Thanks