Ok so the basic outline is that my cousin apparently connected my phone in developer mode and then entered the following commands into the fastboot terminal.
Code:
adb reboot fastboot
fastboot erase data
fastboot erase cache
fastboot erase system
What worries me is the last command
Code:
fastboot erase system
I suspect that he has erased the ROM itself and now my phone is in a state where the phone just shows the intex logo and then vibrates a little but thats just about it.
So my question is that is my phone recoverable?
NOTE:My phone has not been rooted
Related
I have this device, and i booted it in fastboot mode successfully. Open ADB and type "adb reboot-bootloader", the phone will reboot and remain stuck in the boot logo (HTC powered by android). Now open fastboot and type "fastboot devices" and it will be recognized. All commands are working. but I can't unlock bootloader, because when i type "fastboot oem get_identifier_token" it remains stuck with three dots. so i need anyone to help me to solve this issue to unlock my device lease .
Unable to enter fastboot mode
Hey can you tell me how you got into fastboot mode? I can't . I tired volume down+power but phone boots normally. Tried V-up+power then come recovery mode but no fastboot.
Please tell me how ?
Device is in fastboot mode and it is not responding further.
i was trying to root my phone and it is saying okay when wrote command "fastboot oem unlock" but it is not showing that erase data screen(not going to further step). i need to root phone. :/
please help.
pls help
does ur device boot into the OS or is it bricked?
Hello recently an automatic firmware update happened on my phone , after the update has finished my phone is now stucked on the EMUI after booting up. My phone has bootloader unlocked
update:
i flashed the stock rom using adb & fastboot
i flashed these
ramdisk.img
kernel.img
recovery-ramdis.img
system.img
wiped / format the data and the cache partition
Was all succcess but now im getting stucked on the ""your device has been unlocked and can't be trusted" screen
pls send help
upppppppp pla help
im still getting stucked please help
up i need help please
bumpy uppp
up please help
then try to go to erecovery by pressing volume up while the your device has been unlocked and can't be trusted
i can help if u like remotly
Did you find a solution
anonpurged09 said:
update:
i flashed the stock rom using adb & fastboot
i flashed these
ramdisk.img
kernel.img
recovery-ramdis.img
system.img
wiped / format the data and the cache partition
Was all succcess but now im getting stucked on the ""your device has been unlocked and can't be trusted" screen
pls send help
Click to expand...
Click to collapse
install minimal adb and fastboot tool (for quickness) on window's computer
Put your phone back into fastboot mode (insert usb with mobile switched off whilst holding the volume up button and plugged into your laptop)
Check your bootloader's status with this command fastboot oem device-info And then go back and lock your bootloader again using the fastboot oem lock command then restart your phone in recovery mode and factory reset it .....you may have to put your phone's serial number at the end off fastboot oem lock ************* you can get it using the fastboot devices command,just copy and paste serial " at end of your command then use the fastboot oem device-info command again to check that you have been successful.....Failing that you might have to re-flash and try a fresh download of firmware stock rom from a different source as it might be corrupted
Good luck.
I was trying to flash TWRP in Gionee P5W. The steps I followed were:
1. adb reboot bootloader
2. fastboot oem unlock
3. fastboot flash recovery recovery.img (had prepared TWRP img file already)
4. fastboot reboot recovery
I later found out that the last command should had been fastboot boot recovery.img.
Now my phone is stuck in bootloop. I tried going into recovery (vol-up + power) but I only gat the gionee logo and then the boot loop. What is the condition with my phone and is there something that can be done?
Instructions for installing GSI firmware based on Android 10/11 for OnePlus Nord N100.
1. We flash the stock firmware of OxygenOS 10.5.5 through the EDL mode using MSMDownload.
2. After launching the newly installed system, go to Settings-About the phone, click on the Build Number several times until it is indicated that you have become a Developer.
Go to the System section, the item For Developers, activate the Factory Unlock slider and Reboot Options, and also activate USB Debugging.
3. Restart the smartphone in Fastboot by holding down the power button and selecting the Loader item. We connect it to the PC. On a PC, open the command line from the folder with adb tools and firmware in .img format. Enter the command: fastboot flashing unlock_critical (all data will be deleted). We wait for the end of the procedure, reboots again in Fastboot, and enter the following command: fastboot -w. Next, the command: fastboot reboot fastboot. The smartphone will reboot into Fastbootd mode, in which we will perform all further actions.
4. Enter the command: fastboot erase system. We remember which partition was cleared, system_a or system_b (this is important!).
The next command we need to execute is: fastboot resize-logical-partition product (_a or _b depends on which system partition was cleared) 709344768.
Next: fastboot resize-logical-partition system (the same as with product) 2600000000.
Next, we flash the system itself. Command: fastboot --disable-verity --disable-verification flash system (depending on which partition was erased, _a or _b, enter the one) "file path".
5. After the firmware is finished, enter the command: fastboot reboot. The smartphone will boot into the system.
i tried booting into fastbootd mode which it does on the phone but on cmd its stuck saying waiting for device