I have hard bricked my phone during flashing of rom,
1.Now the device is not powering on
2.it is not recognized by the pc
3.It only gives pop up sound when plugged in and out
somebody help me get me my device back on :
Install proper mtk drivers, if possible test it with another K4 device to connect with pc,
Sent from my Lenovo A7010a48 using XDA Premium 4 mobile app
niranjans8496 said:
I have hard bricked my phone during flashing of rom,
1.Now the device is not powering on
2.it is not recognized by the pc
3.It only gives pop up sound when plugged in and out
somebody help me get me my device back on :
Click to expand...
Click to collapse
Your phone cannot be hard bricked by flashing software. I think you must repeat the procedure by reseting the phone. I think you must seek on the net how to reset your phone.
Send from my Lenovo P1 Pro
niranjans8496 said:
I have hard bricked my phone during flashing of rom,
1.Now the device is not powering on
2.it is not recognized by the pc
3.It only gives pop up sound when plugged in and out
somebody help me get me my device back on :
Click to expand...
Click to collapse
Install proper MTK driver on your PC then search for lenovo k4 note firmware on the internet. Then flash it by using SP Flash tool. Be careful of the firmware that you gonna flash, it should be the same kernel and firmware of your device. . Otherwise it will not work. Search for the instructions in the internet.
Sent from my Lenovo A7010a48 using XDA-Developers mobile app
my lenovo k4 note also hardbricked tell me if you got the problem solved please
niranjans8496 said:
I have hard bricked my phone during flashing of rom,
1.Now the device is not powering on
2.it is not recognized by the pc
3.It only gives pop up sound when plugged in and out
somebody help me get me my device back on :
Click to expand...
Click to collapse
same problem
saikumar.2154 said:
same problem
Click to expand...
Click to collapse
If you hear the sound when you plug the phone to the computer, the sound means that the computer recognises the phone.
Open the device manager and look at the ports area. After you open the ports are plug the phone. Now you should see your phone for 1 or 2 seconds, after the disappears.
The trick is to press the download button on sound flash tool in that moment.
Hope this will help you. Good luck.
Not turning on also no vibration.But can successfully completed flashing.
Help me Lenovo K4 note
niranjans8496 said:
I have hard bricked my phone during flashing of rom,
1.Now the device is not powering on
2.it is not recognized by the pc
3.It only gives pop up sound when plugged in and out
somebody help me get me my device back on :
Click to expand...
Click to collapse
Related
My phone is royally stuffed now. A few days ago, it started showing error message (image) and this morning after a restart, its stuck at the green android logo and won't get into the operating system. I tried the following and didn't work:
- remove sd card, battery both sim cards
- press vol+ and insert into my computer's usb slot
- MT65xx preloader appeared briefly (about 3 secs) in Device Manager and disappear. Too brief for me to do anything
I also tried power and vol+ buttons to get into recovery but I only get a dead Android image with "No Command" message (similar to image).
Before this problem, my computer can connect to my phone fine and I am using ADB_usb_driver_120827 and successfully rooted it about 2 months ago.
I can try something if my computer can hold the USB connection but how to get a USB connection? Please help?
OK my computer can see my phone as an ADB Interface but I still can't connect MTK Tools or SP Flash to it. Any help?
dreamerman said:
OK my computer can see my phone as an ADB Interface but I still can't connect MTK Tools or SP Flash to it. Any help?
Click to expand...
Click to collapse
Connect to the same port you used for root....
Hold only vol up (may be down)
Reinstall drivers....
Follow more methods @ unbrick mt 6577 it may help....
Sent from my IRIS_501 using xda premium
akash akya said:
Connect to the same port you used for root....
Hold only vol up (may be down)
Reinstall drivers....
Follow more methods @ unbrick mt 6577 it may help....
Click to expand...
Click to collapse
Thanks for your help. I fixed it by entering into recovery mode and factory reset it.
Hello
I have a tablet Lenovo IdeaTab A2107A-H (16GB) and i have problem, few days ago tablet dead because i Installed Foxrot ROM and all time screen is Black ;(. I have installed all drivers for ADB and MTK Preloader, but when i take reset, next hold Vol+ and Power windows see my tablet not like a MTK Preloader but like Unkown device in USB Section with a Yellow triangle. Decive id :USB\Vid_0000&Pid_0000\6&373d4c5d&0&3 and i can't load any drivers for this tablet ;( I need help to back to life my tablet.
I don't know what battery procentage is. May be this is a problem?
I try to edit inf drivers but with no success. Everytime my device is looking like USB/UNKOWN
Pictures:
http://imageshack.com/a/img69/7388/894k.png
http://imageshack.com/a/img691/183/0wy8.png
http://imageshack.com/a/img850/3954/oml6.png
http://imageshack.com/a/img823/9103/qb2z.png
http://imageshack.com/a/img132/8668/1axl.png
http://imageshack.com/a/img850/3405/hx1h.png
I found something about test point on MTK 6575 but i can't found testpoint at a2-mb-h301 motherboard ;(
Can anyone help me?? to find testpoint or back my tablet to life??
f5
Can anyone know how fix this??
Flash a Stock rom.
Sent from my Lenovo A706_ROW using XDA Premium 4 mobile app
Ragkhuza said:
Flash a Stock rom.
Sent from my Lenovo A706_ROW using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Yes but what do this
damossq said:
Yes but what do this
Click to expand...
Click to collapse
First of all download a stock rom for your device(if you don't have).
Questions: Can you enter droid boot on your device?
Can you access the files from your computer?
Ragkhuza said:
First of all download a stock rom for your device(if you don't have).
Questions: Can you enter droid boot on your device?
Can you access the files from your computer?
Click to expand...
Click to collapse
i have pregramency rom and some chinise stock rom.
When i connect tablet to Pc and hold Vol + or -, power. my computer see only unkown device. I have installed all adb drivers ( preloader too). ;(
damossq said:
i have pregramency rom and some chinise stock rom.
When i connect tablet to Pc and hold Vol + or -, power. my computer see only unkown device. I have installed all adb drivers ( preloader too). ;(
Click to expand...
Click to collapse
Sorry for my late reply. Maybe this thread will help you. http://forum.xda-developers.com/showthread.php?t=2428319
As long as you can access your tablet to your pc, there still hope brother.
:crying: Guys , my SP Flash Tool keep stucking at "100%RedBar" and "0%" . I can't flash anything... :crying: Help me pls...
tngultimate said:
:crying: Guys , my SP Flash Tool keep stucking at "100%RedBar" and "0%" . I can't flash anything... :crying: Help me pls...
Click to expand...
Click to collapse
What are tryng to flash?
Sent from my Lenovo P780
stympy said:
What are tryng to flash?
Sent from my Lenovo P780
Click to expand...
Click to collapse
Lenovo P780 stock rom s124
tngultimate said:
Lenovo P780 stock rom s124
Click to expand...
Click to collapse
Use spflash tool 5 not 3. In spflash tool 5 select firmware upgrade not download.
Try and tel me if works.
Sent from my Lenovo P780
stympy said:
Use spflash tool 5 not 3. In spflash tool 5 select firmware upgrade not download.
Try and tel me if works.
Sent from my Lenovo P780
Click to expand...
Click to collapse
It keep saying "Unrecognized Rom" detected
tngultimate said:
It keep saying "Unrecognized Rom" detected
Click to expand...
Click to collapse
Soo.. Sp flash tool 3 is telling you the same thing ?
Sent from my Lenovo P780
stympy said:
Soo.. Sp flash tool 3 is telling you the same thing ?
Sent from my Lenovo P780
Click to expand...
Click to collapse
sp flash tool 3 just stuck at red bar or 0 %...
tngultimate said:
sp flash tool 3 just stuck at red bar or 0 %...
Click to expand...
Click to collapse
Use spflash tool 3 open the back of your phone and press the red button on your right for 20 secconds after yo pressed firmware upgrade button abd pluged your cable.
Sent from my Lenovo P780
stympy said:
Use spflash tool 3 open the back of your phone and press the red button on your right for 20 secconds after yo pressed firmware upgrade button abd pluged your cable.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Also stuck at 0% ... but the time keep increasing . After 40 seconds , it appear a message says
BROM ERROR : S_FT_READBACK_FAIL (4009)
tngultimate said:
Also stuck at 0% ... but the time keep increasing . After 40 seconds , it appear a message says
BROM ERROR : S_FT_READBACK_FAIL (4009)
Click to expand...
Click to collapse
Hi. Lets try this: since "Firmware Upgrade" or "Download" option dont work, first "Format---->Auto Format Whole NAND flash", then flash ROM using "Download" option with "DA/DL all" selected !!!
Tell me if works.
stympy said:
Hi. Lets try this: since "Firmware Upgrade" or "Download" option dont work, first "Format---->Auto Format Whole NAND flash", then flash ROM using "Download" option with "DA/DL all" selected !!!
Tell me if works.
Click to expand...
Click to collapse
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
tngultimate said:
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
Click to expand...
Click to collapse
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
stympy said:
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
Click to expand...
Click to collapse
I have the exact same issue. Flashing stock S124 after (rooted) S223 with SpTools messes something up.
I managed to do a TWRP restore to go back to S221 but I can't use SpTools anymore.
I get the same SpTools error message. Only after pressing the red reset button my phone will then come back to life.
stympy said:
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
Click to expand...
Click to collapse
Nothing happen...
londondutch said:
I have the exact same issue. Flashing stock S124 after (rooted) S223 with SpTools messes something up.
I managed to do a TWRP restore to go back to S221 but I can't use SpTools anymore.
I get the same SpTools error message. Only after pressing the red reset button my phone will then come back to life.
Click to expand...
Click to collapse
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
---------- Post added at 03:58 PM ---------- Previous post was at 03:57 PM ----------
tngultimate said:
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
Click to expand...
Click to collapse
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
stympy said:
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
---------- Post added at 03:58 PM ---------- Previous post was at 03:57 PM ----------
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
Click to expand...
Click to collapse
Thanks for your explanation, you seem to be the absolute guru on this site for this device! I think you are right about the preloader being messed up. I tried to install the USB driver (again) for the new device that the computer now sees. It is listed in the device manager as "Unknown Device" under USB controllers. I can't seem to force it to accept new USB drivers for it (Lenovo drivers). It keeps saying that the driver is not compatible with the device. I use Win 7 64bit, could that have something to do with it? Also is it possible to flash a new preloader using TWRP? If I press the reset button on my phone it reboots fine (rooted S221) and I have TWRP installed.
londondutch said:
Thanks for your explanation, you seem to be the absolute guru on this site for this device! I think you are right about the preloader being messed up. I tried to install the USB driver (again) for the new device that the computer now sees. It is listed in the device manager as "Unknown Device" under USB controllers. I can't seem to force it to accept new USB drivers for it (Lenovo drivers). It keeps saying that the driver is not compatible with the device. I use Win 7 64bit, could that have something to do with it? Also is it possible to flash a new preloader using TWRP? If I press the reset button on my phone it reboots fine (rooted S221) and I have TWRP installed.
Click to expand...
Click to collapse
Here are the drivers i use! Hope this will help you!
Soo.. i never tried to flash preloader from TWRP. Thats an ideea, but you have to do a full backup of your phone... i think...
When i have preloader problems i flash again the whole ROM. I think is safer, better... and wize.
stympy said:
Here are the drivers i use! Hope this will help you!
Soo.. i never tried to flash preloader from TWRP. Thats an ideea, but you have to do a full backup of your phone... i think...
When i have preloader problems i flash again the whole ROM. I think is safer, better... and wize.
Click to expand...
Click to collapse
Thanks for the drivers, I am still struggling to make this "Unknown Device" accept other drivers. What was your unrecognised phone called in Device Manager? Was it also "Unknown Device" in the USB section?
londondutch said:
Thanks for the drivers, I am still struggling to make this "Unknown Device" accept other drivers. What was your unrecognised phone called in Device Manager? Was it also "Unknown Device" in the USB section?
Click to expand...
Click to collapse
Hi. The think was someting like this:
First i installed the .exe file. Reboot PC.
2. I have plugged the phone to the PC and new hardware wizard has appeared.
3. Now i have powered of the phone.
4. Again i have plugged the phone this time powered off.
5. At this time in Device Manager appeared for a second or two not in USB area something with.. MTK65...
6. Click very fast on it because that will desapear very fast.
7. After you clicked on it all you have to do is update driver, and voila you have drivers installed and now all you have to do is to flash you ROM.
Hope this will help you.
Good luck.
Sent from my Lenovo P780
stympy said:
Hi. The think was someting like this:
First i installed the .exe file. Reboot PC.
2. I have plugged the phone to the PC and new hardware wizard has appeared.
3. Now i have powered of the phone.
4. Again i have plugged the phone this time powered off.
5. At this time in Device Manager appeared for a second or two not in USB area something with.. MTK65...
6. Click very fast on it because that will desapear very fast.
7. After you clicked on it all you have to do is update driver, and voila you have drivers installed and now all you have to do is to flash you ROM.
Hope this will help you.
Good luck.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Thanks !!! ^^ Finally I won !!! You are like the proffesion in P780 !!! Stympy , another thing i want to ask you , how to root S223 the rom that you give ? I saw there was an alternative scatter in your S223 .
A while ago I made a post about how I hardbricked my Wiko Lenny, and I finally decided to try the testpoint method. The problem is that I have absolutely no idea as to where that testpoint is on the PCB.
Can someone guide me? I attached some pictures with the PCB.
Okay, I found the testpoint. It's noted as KCOL0, and it's under the PCB, near the volume up button. I connected GND with KCOL0, but the phone is rapidly switching on and off. I can't flash it in this state.
After a few minutes of constant switching on and off, the phone decided to calm down and let the PC detect it.
In Device Manager it appears as "USB Serial Device (COM6)", and SP Flash Tools v5 detects it easily. But it can't flash it. It always spits out this: "S_FT_ENABLE_DRAM_FAIL" and stops.
Any ideas?
Come on, guys... Someone here must have at least a bit of experience with Mediatek phones...
Please tell me your status for now, also tell me how you got into this ??
I mean how you made a brick??
My phone has the habit of simply going into a bootloop once every few months. I always repair it by reflashing the ROM in SP Flash Tool, but last time I used a tool supplied by Wiko. Apparently the tool reflashed the entire phone instead of the Android partition, and managed to corrupt the preloader. As a result, the phone didn't turn on, vibrate, or even get recognized by the PC.
A while ago I made a post about this, but nobody wanted to help me. I researched the internet and found out that the phone can be repaired by META mode, by JTAG or by testpoint. META mode isn't available on MT6572 devices, so that didn't work. JTAG seems too complicated for me, so the last option was shortcircuiting the KCOL0 testpoint.
I opened up the phone's back, took the PCB out and soldered a copper wire that connected the groundpoint(GND) with the testpoint(KCOL0). After connecting it to the computer, the phone started turning off and on rapidly for around 10 minutes, then decided to stop, letting it be recognized by the PC. It appeared as "USB Serial Device", but it should be called "Mediatek MTK PRELOADER" or something similar. I thought it was the PC, so I continued.
Started SPFT, loaded a scatter that I backed up from the last flash, then clicked Download. After 30 seconds it stops and writes this: "BROM ERROR: S_FT_ENABLE_DRAM_FAIL (4032)". Tried resoldering and reflashing, but same result.
Any ideas?
DragonSky87 said:
Any ideas?
Click to expand...
Click to collapse
Error 4032
Message: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
* Ensure that the file(s) you're trying to flash are actually for your exact phone model
* Ensure you tick the boxes for only the files present in the ROM you're about to flash
* Probably have the wrong driver installed. Uninstall vcom, preloader and MTK drivers using usb deview then manually re-install using forum.hovatek.com/thread-440.html
* Delete the sp flash tool folder then re-extract
* Ensure the phone is switched off (with battery still inside) before connecting to PC for flashing.
* If that doesn't work, keep holding down the volume decrease button just before connecting the phone to PC for flashing (you could try volume increase , power + volume decrease or power + volume increase).
* Consider using the latest version of Sp Flash tool
* Format the phone before trying to flash the file(s) again
Ti-am scris si un mesaj privat. Mi-ar place daca m-ai putea ajuta
VanCroft said:
Error 4032
Message: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
* Ensure that the file(s) you're trying to flash are actually for your exact phone model
* Ensure you tick the boxes for only the files present in the ROM you're about to flash
* Probably have the wrong driver installed. Uninstall vcom, preloader and MTK drivers using usb deview then manually re-install using forum.hovatek.com/thread-440.html
* Delete the sp flash tool folder then re-extract
* Ensure the phone is switched off (with battery still inside) before connecting to PC for flashing.
* If that doesn't work, keep holding down the volume decrease button just before connecting the phone to PC for flashing (you could try volume increase , power + volume decrease or power + volume increase).
* Consider using the latest version of Sp Flash tool
* Format the phone before trying to flash the file(s) again
Ti-am scris si un mesaj privat. Mi-ar place daca m-ai putea ajuta
Click to expand...
Click to collapse
First : sorry for my bad english; I have wiko lenny too and after I dismantled the phone, and found KCOL0 TP, shorted it to Ground and connected USB cable and after that my phone is conecting and disconecting all the time. Not remain conected and can`t flash firmware.Please help me with any sugestions. Thanks in advance.
VanCroft said:
First : sorry for my bad english; I have wiko lenny too and after I dismantled the phone, and found KCOL0 TP, shorted it to Ground and connected USB cable and after that my phone is conecting and disconecting all the time. Not remain conected and can`t flash firmware.Please help me with any sugestions. Thanks in advance.
Click to expand...
Click to collapse
Nobody knows ?
VanCroft said:
Nobody knows ?
Click to expand...
Click to collapse
Sorry for my English.
I have one with the same "dead".
Make short between Kcolo point and GND.
Be sure battery is full.
Use V20 firmware.
Select firmware up-grade from Smart Phone Flash Tools.
Connect phone to PC with Volume + push
Don't forget to remove the jumper after flash
VirtualG said:
Sorry for my English.
I have one with the same "dead".
Make short between Kcolo point and GND.
Be sure battery is full.
Use V20 firmware.
Select firmware up-grade from Smart Phone Flash Tools.
Connect phone to PC with Volume + push
Don't forget to remove the jumper after flash
Click to expand...
Click to collapse
Thanks for reply! After short betwen Kcolo and GND I must insert the battery ? and then flash? First time
I thought the battery should be removed Ok! I will try now
VanCroft said:
Thanks for reply! After short betwen Kcolo and GND I must insert the battery ? and then flash? First time
I thought the battery should be removed Ok! I will try now
Click to expand...
Click to collapse
Thank you very much!!!!!!!!!
I managed to bring it to life:laugh:
Brother have you fixed or still need support ?
Let me know if you need something
Sent from my Lenovo IdeaTab S6000-H Using XDA Premium 5
maged.homaid said:
Brother have you fixed or still need support ?
Let me know if you need something
Sent from my Lenovo IdeaTab S6000-H Using XDA Premium 5
Click to expand...
Click to collapse
Thank you. I have done, my phone is working now.:laugh:
VanCroft said:
Thank you. I have done, my phone is working now.:laugh:
Click to expand...
Click to collapse
Good news brother
Congratulations..
Sent from my Lenovo IdeaTab S6000-H Using XDA Premium 5
I still didn't manage to repair it, as I may have made a mistake while soldering and shortcircuited the phone.
I may try again, though.
I have the same issue but my Wiko Lenny 3 is dead for a while (like 2-4 years). Until this time, I was trying to repair my device, but no luck occurred. But I can't find the KCOLO point, as I should. It is either on the main board / motherboard (I don't know how to call it) or under it. I'm of a smartphone repair noob...
I hope that I can finally manage to repair this device because I don't know what I should do with this device.
And added the image to see if you guys can find the KCOLO / KOLO / COLO point...
Hi there,
i have made a mistake
i wanted to root so i flashed the trwp but i missed to deselect all options in the flashtool
now the phone does not start and in windows (win 10) it shows only as unkown device after 30-40 seconds plug in the cabel
i think i have killed the preloader but i cant flash it new with stock rom
i have tried to install all drivers wich could needed but nothing helps and the driver now seems to work not correct (yellow exclamation mark, mtk usb port, Mediatek preeloader Gadgat cdc)
maybe some one could help me, please???
Chokolone said:
Hi there,
i have made a mistake
i wanted to root so i flashed the trwp but i missed to deselect all options in the flashtool
now the phone does not start and in windows (win 10) it shows only as unkown device after 30-40 seconds plug in the cabel
i think i have killed the preloader but i cant flash it new with stock rom
i have tried to install all drivers wich could needed but nothing helps and the driver now seems to work not correct (yellow exclamation mark, mtk usb port, Mediatek preeloader Gadgat cdc)
maybe some one could help me, please???
Click to expand...
Click to collapse
remove the back cover and remove the battery and goodbye again after SPFT
battery is non removeable he might risk totally destroying phone if one of those ribbons goes.
DaBountyHunter said:
battery is non removeable he might risk totally destroying phone if one of those ribbons goes.
Click to expand...
Click to collapse
all removable
VYSquare said:
remove the back cover and remove the battery and goodbye again after SPFT
Click to expand...
Click to collapse
Hi,
perhaps you will need to re-flash your phone with SP Flash Tool.
Download the latest firmware
here is the tutorial to flash : forum elephone
After that you will be able to root your phone using my tuto
Best regards, and I hope this will help you.
scotty2b said:
Hi, perhaps you will need to re-flash your phone with SP Flash Tool..
Click to expand...
Click to collapse
My smart operating normally, there is no need in the firmware
Have you been able to fix your phone?
krogaw said:
Have you been able to fix your phone?
Click to expand...
Click to collapse
I had more or less the same situation. Was able to get into recovery and wiped all there is to wipe! After that I was able to reflash.
Chokolone said:
Hi there,
i have made a mistake
i wanted to root so i flashed the trwp but i missed to deselect all options in the flashtool
now the phone does not start and in windows (win 10) it shows only as unkown device after 30-40 seconds plug in the cabel
i think i have killed the preloader but i cant flash it new with stock rom
i have tried to install all drivers wich could needed but nothing helps and the driver now seems to work not correct (yellow exclamation mark, mtk usb port, Mediatek preeloader Gadgat cdc)
maybe some one could help me, please???
Click to expand...
Click to collapse
VYSquare said:
all removable
Click to expand...
Click to collapse
Sent from my P9000 using XDA-Developers mobile app
Chokolone said:
Hi there,
i have made a mistake
i wanted to root so i flashed the trwp but i missed to deselect all options in the flashtool
now the phone does not start and in windows (win 10) it shows only as unkown device after 30-40 seconds plug in the cabel
i think i have killed the preloader but i cant flash it new with stock rom
i have tried to install all drivers wich could needed but nothing helps and the driver now seems to work not correct (yellow exclamation mark, mtk usb port, Mediatek preeloader Gadgat cdc)
maybe some one could help me, please???
Click to expand...
Click to collapse
Try to remove all drivers and reinstall them. i had the same Problem before. Should work, afterwarda follow the instructions posted before ))