Hey guys!
I have a rooted moto e (1st gen) with cm 13 and have twrp installed! My moto e is stuck on the bootlogo! I am able to access the fast boot mode! But i cannot flash the stock rom as the battery is low! The phone only showes 0% charge n then automatically turns on! Wht shud i do! How can i get my battery charged to flash the stock rom! Plz help!!!
shamit_kothari said:
Hey guys!
I have a rooted moto e (1st gen) with cm 13 and have twrp installed! My moto e is stuck on the bootlogo! I am able to access the fast boot mode! But i cannot flash the stock rom as the battery is low! The phone only showes 0% charge n then automatically turns on! Wht shud i do! How can i get my battery charged to flash the stock rom! Plz help!!!
Click to expand...
Click to collapse
Hi,
Can u still go in twrp and what's its version?
satanas17 said:
Hi,
Can u still go in twrp and what's its version?
Click to expand...
Click to collapse
No was not able to! But i tried removing the battery and the "low battery" signal was gone! Flashed the custom rom! And left it to charge! And everything went fine!
shamit_kothari said:
No was not able to! But i tried removing the battery and the "low battery" signal was gone! Flashed the custom rom! And left it to charge! And everything went fine!
Click to expand...
Click to collapse
Happy ending, that's the best way...
Sent from my Motorola XT1039 using XDA Labs
satanas17 said:
Happy ending, that's the best way...
Sent from my Motorola XT1039 using XDA Labs
Click to expand...
Click to collapse
Always!
shamit_kothari said:
No was not able to! But i tried removing the battery and the "low battery" signal was gone! Flashed the custom rom! And left it to charge! And everything went fine!
Click to expand...
Click to collapse
How did you remove the batter? I am facing a similar problem of phone not charging.
Ptmaroct said:
How did you remove the batter? I am facing a similar problem of phone not charging.
Click to expand...
Click to collapse
There are 14 screws on the back of the phone. Remove eaxh one of them. Then with ur nail try to remove the back panel! Be carefully! Do not apply to much force! It will open towards the right side with a wire attached between the motherboard and battery! Use a tweezer to carefully unplug the wire from the motherboard! After removing the battery connect the phone to the charger and enter fastboot mode!
Hope this helps!:good:
Related
Hi
I have my phone setup to dual boot turkbey and D2 roms using the latest siyah kernel, now and again my ohone switches off while in my pocket or not in use and when i pull the battery and switch back on, the battery has drained as much as 80%.
Anybody know what could be causing this problem?
Cheers.
i gess ur phone is not properly flashd to dual boot and second remove dual boot and use one rom with an otha kernel....or try flashing otha kernel...
jpopgt said:
Hi
I have my phone setup to dual boot turkbey and D2 roms using the latest siyah kernel, now and again my ohone switches off while in my pocket or not in use and when i pull the battery and switch back on, the battery has drained as much as 80%.
Anybody know what could be causing this problem?
Cheers.
Click to expand...
Click to collapse
Its simple the battery is Not calibrated properly
tarunagg said:
Its simple the battery is Not calibrated properly
Click to expand...
Click to collapse
NONSENSE .
jje
Thanks for the replies.
I am pretty sure i followed the correct guide to dual boot and my battery always gets calibrated after installing a new rom.
I will remove dual boot for now and see if it happens with the one rom then.
Cheers.
So, Just Last Night I Rooted My Friend's Motorola Droid Razr (xt912) and installed Cyanogenmod on KitKat 4.4. It Was Working Fine and All Until He Decided to Go into Safestrap and Wipe the Stock ROM That was installed because he thought he wouldn't ever use it. He Went Back to The Cyanogenmod ROM and Activated it, and Rebooted to System. When Booting Up, It Just Gets Stuck on The Red Motorola M. It Will Go Into the Boot Menu but We Can't Find a Solution. Any Ideas on How To Get This Phone To Work Again?
Mistive said:
So, Just Last Night I Rooted My Friend's Motorola Droid Razr (xt912) and installed Cyanogenmod on KitKat 4.4. It Was Working Fine and All Until He Decided to Go into Safestrap and Wipe the Stock ROM That was installed because he thought he wouldn't ever use it. He Went Back to The Cyanogenmod ROM and Activated it, and Rebooted to System. When Booting Up, It Just Gets Stuck on The Red Motorola M. It Will Go Into the Boot Menu but We Can't Find a Solution. Any Ideas on How To Get This Phone To Work Again?
Click to expand...
Click to collapse
I would download mattlgroffs windows utility i had my phone stuck on the same screen and ran the utility now its up and running again just google the utility unzip it and follow the instructions if you need help let me know i can help you jump start the phone if its dead i just did it and it works 100% dont waste money buying a special cord... let me know if you need help
Sent from my DROIDX using xda app-developers app
Mistive said:
So, Just Last Night I Rooted My Friend's Motorola Droid Razr (xt912) and installed Cyanogenmod on KitKat 4.4. It Was Working Fine and All Until He Decided to Go into Safestrap and Wipe the Stock ROM That was installed because he thought he wouldn't ever use it. He Went Back to The Cyanogenmod ROM and Activated it, and Rebooted to System. When Booting Up, It Just Gets Stuck on The Red Motorola M. It Will Go Into the Boot Menu but We Can't Find a Solution. Any Ideas on How To Get This Phone To Work Again?
Click to expand...
Click to collapse
See http://forum.xda-developers.com/showthread.php?t=2192467
Sent from my XT912 using Tapatalk
Dwillian said:
See http://forum.xda-developers.com/showthread.php?t=2192467
Sent from my XT912 using Tapatalk
Click to expand...
Click to collapse
Yes download that utility and if you go into fast boot (power+volume up + down) and go to ap fast boot it will say either battery OK or battery low if it says low u will need a special USB cord or jump start the phone I can walk you through how to do that if you need me to hope it works for you
Sent from my DROID RAZR using xda premium
Thank You Guys So Much! I'm Gonna Try this Tomorrow and I'll Get Back to You Then
melshubby said:
Yes download that utility and if you go into fast boot (power+volume up + down) and go to ap fast boot it will say either battery OK or battery low if it says low u will need a special USB cord or jump start the phone I can walk you through how to do that if you need me to hope it works for you
Sent from my DROID RAZR using xda premium
Click to expand...
Click to collapse
So Yeah, It Says The Battery is Low. Should I Just Let it Charge? I'm Using an HTC Cable.
Mistive said:
So Yeah, It Says The Battery is Low. Should I Just Let it Charge? I'm Using an HTC Cable.
Click to expand...
Click to collapse
If it is charging then yes let it charge. The problem is that it probably will not charge and you will likely need the special factory cable.
I have seen some posts where people were able to get the phone to start charging again without the factory cable. You may want do some searching if you are having charging problems.
Here's a link: https://forums.motorola.com/posts/8df247065b
Hero's another: http://www.android.gs/droid-razr-maxx-update-android-4-1-2-jelly-bean/
Sent from my XT912 using Tapatalk
Yeah You're Right, The White Charge Light Will Come on But It Will Just Not Really Charge.
I Tried Doing This- www . youtube . com/watch?v=LtA4OU2xha4 But Once I Click The Tools and The Motorola M Goes Away, It Stays at a Black Screen Until I Turn it Off.
Now, I am Going To Try This- www . youtube . com/watch?v=XwwI_6doBWk Which I am Assuming is a Factory Cable or Something Like That.
Hi guys i accidently bricked my lg g2 (d620r) trying to unlock my bootloader (i was in official 5.0.2 and i tryed aboot4.img for kitkat) and after a lot of days i finally found out how to unbrick it...
So first you have to make sure the phone's battery is at 0% (you can test this by connecting your phone to your pc with the battery in if it power up without pressing any button then its at 0% if its not then it will do absolutely nothing)
so your phone WILL power up but it will imediately power off again because the battery is at 0% so unplug it and wait till a 0% battery icon appear i the screen
when you see the icon press and hold the volume up button and plug the phone to your pc
now you are in download mode and you can flash a .kdz file (lollipop or kitkat)
ps: this method worked for me and i have my phone back, i dont know if it work for you too
ps:if you dont know how to get your battery to 0% just leave it in the phone and it will drain itself(i think)that worked for me
ps2:my english is not good enough so forgive me if i made some mistakes and correct me
Thank you and i hope you can get your phone back too
You don't need to discharge it..
1) take out the battery
2) plug the phone in a PC via micro USB
3) while holding volume up, put in the battery
4) screen whill pop up asking you to hold volume up, relise it and press it agen till you get in download mode.
panagiotisden2 said:
Hi guys i accidently bricked my lg g2 (d620r) trying to unlock my bootloader (i was in official 5.0.2 and i tryed aboot4.img for kitkat) and after a lot of days i finally found out how to unbrick it...
So first you have to make sure the phone's battery is at 0% (you can test this by connecting your phone to your pc with the battery in if it power up without pressing any button then its at 0% if its not then it will do absolutely nothing)
so your phone WILL power up but it will imediately power off again because the battery is at 0% so unplug it and wait till a 0% battery icon appear i the screen
when you see the icon press and hold the volume up button and plug the phone to your pc
now you are in download mode and you can flash a .kdz file (lollipop or kitkat)
ps: this method worked for me and i have my phone back, i dont know if it work for you too
ps:if you dont know how to get your battery to 0% just leave it in the phone and it will drain itself(i think)that worked for me
ps2:my english is not good enough so forgive me if i made some mistakes and correct me
Thank you and i hope you can get your phone back too
Click to expand...
Click to collapse
i have the same problem, but i cannot resolve with this method...
someone tried USB JIG method? it worked? please let me know
ByN3r0 said:
i have the same problem, but i cannot resolve with this method...
someone tried USB JIG method? it worked? please let me know
Click to expand...
Click to collapse
Are you sure that your battery is FULLY uncharged?
panagiotisden2 said:
Are you sure that your battery is FULLY uncharged?
Click to expand...
Click to collapse
my download mode isn't working in any way, i think i should sent it for repair
Thanks !
Thank you !
shalev1418 said:
Thank you !
Click to expand...
Click to collapse
you're wellcome
Did you unbriced your phone easy?
panagiotisden2 said:
you're wellcome
Did you unbriced your phone easy?
Click to expand...
Click to collapse
YUP!
shalev1418 said:
YUP!
Click to expand...
Click to collapse
Ok thank you. Im glad my method works
bartvp said:
my download mode isn't working in any way, i think i should sent it for repair
Click to expand...
Click to collapse
Hello, I am also having the same problem and could not solve = [
many already succeeded with the G2 and the same software used for the g2 min, but lack the file.
http://forum.xda-developers.com/lg-g2/general/file-unbrick-qualcomm-9006-qhsusb-t3056800
could anyone help?
Thank you!
I hard bricked my D620R for the same reason, and was about to send to repair.
Then I tried this way, I waited a day with the battery pulled on, and it got discharged. Finally I was able to get into download mode!
marcio1477 said:
Hello, I am also having the same problem and could not solve = [
many already succeeded with the G2 and the same software used for the g2 min, but lack the file.
http://forum.xda-developers.com/lg-g2/general/file-unbrick-qualcomm-9006-qhsusb-t3056800
could anyone help?
Click to expand...
Click to collapse
You should send it i've done it too. I think your phone is back within 3 weeks
I'm also waiting until my 3 weeks are finished
deviato said:
Thank you!
I hard bricked my D620R for the same reason, and was about to send to repair.
Then I tried this way, I waited a day with the battery pulled on, and it got discharged. Finally I was able to get into download mode!
Click to expand...
Click to collapse
Ιm glad i helped enjoy your phone
bartvp said:
You should send it i've done it too. I think your phone is back within 3 weeks
I'm also waiting until my 3 weeks are finished
Click to expand...
Click to collapse
So can you tell us what the cost is for repair? and if LG said anything about trying to unlock your bootloder/ root it/flashing other roms etc.?
panagiotisden2 said:
So can you tell us what the cost is for repair? and if LG said anything about trying to unlock your bootloder/ root it/flashing other roms etc.?
Click to expand...
Click to collapse
I don't know. I read somewhere that it costs around $30-50. But maybe my warranty isn't void, because they can't check (maybe) my phone is rooted, so it costs nothing.
The only thing I can do is waiting and waiting...
---------- Post added at 07:04 AM ---------- Previous post was at 06:53 AM ----------
marcio1477 said:
Hello, I am also having the same problem and could not solve = [
many already succeeded with the G2 and the same software used for the g2 min, but lack the file.
http://forum.xda-developers.com/lg-g2/general/file-unbrick-qualcomm-9006-qhsusb-t3056800
could anyone help?
Click to expand...
Click to collapse
I will never do this . You only brick it harder i think
HI!
I have D620r. I tryed fw update with LG MobileSupportTool. It stuck at 2, or 3%, never goes up!!
Now, when I try power up, it show only: fastboot operation. I don't have download mode.
I left battery 0%, but this metod don't work too...
It is possible flash stock fw in fastboot mode, or it is bricked?
REQUEST: Can someone who have a bricked device record a video unbricking it with me method, so more users can easily unbrick their devices too just by watching the video tutorial?
Thanks
I tried
I tried to follow your steps but i can go download mode the smartphone start to charge :crying:
help pls
anyone knows how to install a ROM with the phone on scares me turn it off because it was lucky to keep on achieving at the moment is in safe mode
chacks1 said:
anyone knows how to install a ROM with the phone on scares me turn it off because it was lucky to keep on achieving at the moment is in safe mode
Click to expand...
Click to collapse
It's not possible. If you try, ROM's filesystem will replace the files you are using, making the device unusable (soft-bricked).
Respected Sir, I Was Using My Loveable Moto E in a Sweety Manner. I Really like the Handset the most.. It was on rooted android 4.4.4 : Was Using Xposed & Busy Box & some of their Modules. It was working fine but today suddenly when the battery level dropped to 0% then I had seen that the Android system was closing & the device was shutting Down.. After that I have Left the device for charging over 2-3 hours but only the white LED is blinking after 5-6 secs. while the device is connected with the charger. No light On the display..device is Not booting.. also unable to enter in the fastboot/bootloader mode.. Please Sir Help Me... I have only one android device & it helps me a lot in my study...
Thank You For Reading Carefully...?
is there none to help me ?????
bhaskar15 said:
is there none to help me ?????
Click to expand...
Click to collapse
Leaver the phone charging all throughout the evening... Try to enter bootloader mode then
Rohitagni said:
Leaver the phone charging all throughout the evening... Try to enter bootloader mode then
Click to expand...
Click to collapse
yesterday whole night it was in charge but still the same problem....????
Hi everyone.
I have a Redmi note 4 4GB RAM 64GB ROM Qualcomm.
One day the phone ran out of battery (0%) and from there there is no way to charge the battery. After testing several chargers and cables, the only way to charge the battery is to connect the phone in fast boot mode to the PC.
If I connect the mobile on:
- to any charger, it does not charge or turn on any led.
- to the PC, it does not recognize it, it does not charge the battery or any led lights up.
If I connect the mobile off:
- to any charger or to the PC, first the Mi logo appears and then it shows the image of a battery with the%, but it does not charge the battery. Right now a yellow LED lights up because the battery is at 79%, it is supposed to charge but after 2 hours it remains the same.
If I connect the mobile in fast boot mode:
- to any charger, it leaves the fast boot mode at 20 seconds and turns on or shows the battery as in the previous case, so it does not charge.
- to the PC, it stays in this mode and charging the battery.
I did all these tests leaving the phone connected several hours for each one.
I restored the factory phone and nothing. I downloaded and installed the stable ROM 9.2.1.0 (NCFMIEK) but it remains the same.
I have also tried the developer version but it still does not work.
Any suggestions?
I haave the similar problem. My redmi note 4 charges only in fastboot mode. Any suggestions to resolve it?
Ackxda said:
I haave the similar problem. My redmi note 4 charges only in fastboot mode. Any suggestions to resolve it?
Click to expand...
Click to collapse
I have the same problem, got any solution ?
I have redmi note 4(mido).
nowito said:
Hi everyone.
I have a Redmi note 4 4GB RAM 64GB ROM Qualcomm.
One day the phone ran out of battery (0%) and from there there is no way to charge the battery. After testing several chargers and cables, the only way to charge the battery is to connect the phone in fast boot mode to the PC.
If I connect the mobile on:
- to any charger, it does not charge or turn on any led.
- to the PC, it does not recognize it, it does not charge the battery or any led lights up.
If I connect the mobile off:
- to any charger or to the PC, first the Mi logo appears and then it shows the image of a battery with the%, but it does not charge the battery. Right now a yellow LED lights up because the battery is at 79%, it is supposed to charge but after 2 hours it remains the same.
If I connect the mobile in fast boot mode:
- to any charger, it leaves the fast boot mode at 20 seconds and turns on or shows the battery as in the previous case, so it does not charge.
- to the PC, it stays in this mode and charging the battery.
I did all these tests leaving the phone connected several hours for each one.
I restored the factory phone and nothing. I downloaded and installed the stable ROM 9.2.1.0 (NCFMIEK) but it remains the same.
I have also tried the developer version but it still does not work.
Any suggestions?
Click to expand...
Click to collapse
Ackxda said:
I haave the similar problem. My redmi note 4 charges only in fastboot mode. Any suggestions to resolve it?
Click to expand...
Click to collapse
Ujwal Bhagat said:
I have the same problem, got any solution ?
I have redmi note 4(mido).
Click to expand...
Click to collapse
Even on custom roms?
MyNameIsRage said:
Even on custom roms?
Click to expand...
Click to collapse
Yes, I tried MIUI Fastboot rom, Lineage 15.1 latest, AOSP Extended. It is present on all of them !
Ujwal Bhagat said:
Yes, I tried MIUI Fastboot rom, Lineage 15.1 latest, AOSP Extended. It is present on all of them !
Click to expand...
Click to collapse
Tried updating firmware?
MyNameIsRage said:
Tried updating firmware?
Click to expand...
Click to collapse
No. I don't know how to update firmware ! Please send a link to update firmware ASAP. Thanks.
UPDATE-1 14/07/18-4:55AM: I installed a stable firmware from here , but I do not notice any difference, the problem is still here.
Ujwal Bhagat said:
No. I don't know how to update firmware ! Please send a link to update firmware ASAP. Thanks.
UPDATE-1 14/07/18-4:55AM: I installed a stable firmware from here , but I do not notice any difference, the problem is still here.
Click to expand...
Click to collapse
Sad.
MyNameIsRage said:
Sad.
Click to expand...
Click to collapse
The phone seems to be charging normally now(after flashing firmware) in AOSP Extended rom. I will keep you guys updated ! Thanks.
Ujwal Bhagat said:
The phone seems to be charging normally now(after flashing firmware) in AOSP Extended rom. I will keep you guys updated ! Thanks.
Click to expand...
Click to collapse
Ohh. It's probably because you flashed it afterwards lol. It's meant to be flashed before the Rom
MyNameIsRage said:
Ohh. It's probably because you flashed it afterwards lol. It's meant to be flashed before the Rom
Click to expand...
Click to collapse
So should I flash the firmware first and then the ROM ?
Ujwal Bhagat said:
So should I flash the firmware first and then the ROM ?
Click to expand...
Click to collapse
Yep. Firmware > rom > gapps mods kernels etc.
MyNameIsRage said:
Yep. Firmware > rom > gapps mods kernels etc.
Click to expand...
Click to collapse
Should I flash Firmware, ROM, etc again ? It seems to be working now.
Ujwal Bhagat said:
Should I flash Firmware, ROM, etc again ? It seems to be working now.
Click to expand...
Click to collapse
If that works then i guess no. It isn't required. It's up to you. Just keep in mind to keep your firmware updated whenever you clean flash a rom.