Please help, my S3 suddenly stuck at Samsung Galaxy S3 GT-1900 screen. Tried to press Home & Vol Down buttons together but no response.
Plug it in, hold just the power button for 10-15 seconds. If no response it's dead. If you get the samsung logo you should be able to get download mode so long as your volume keys work.
Beamed in by telepathy.
shivadow said:
Plug it in, hold just the power button for 10-15 seconds. If no response it's dead. If you get the samsung logo you should be able to get download mode so long as your volume keys work.
Beamed in by telepathy.
Click to expand...
Click to collapse
Hi Shivadow,
I have entered the the ODIN MODE.. then I'm stuck again at "Downloading... Do not turn off target!!!".
What will I do next. Thanks.
Dhongski said:
Hi Shivadow,
I have entered the the ODIN MODE.. then I'm stuck again at "Downloading... Do not turn off target!!!".
What will I do next. Thanks.
Click to expand...
Click to collapse
I tried downloading S3 firmware & Odin3.. but I always get Failed status. Please see below.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNK1_I9300SVZGNJ1_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help please. thanks.
Corrupt or locked bootloader or firmware mismatch (device or carrier). Are you sure you have an I9300?. Check the sticker inside the battery compartment. Make sure it has I9300 on it.
If it is definitely an I9300 then I'd go with corrupt or locked bootloader. Is the device locked to a carrier?. Are you sure that the firmware is the correct one for your carrier?.
Beamed in by telepathy.
shivadow said:
Corrupt or locked bootloader or firmware mismatch (device or carrier). Are you sure you have an I9300?. Check the sticker inside the battery compartment. Make sure it has I9300 on it.
If it is definitely an I9300 then I'd go with corrupt or locked bootloader. Is the device locked to a carrier?. Are you sure that the firmware is the correct one for your carrier?.
Beamed in by telepathy.
Click to expand...
Click to collapse
Awww, I'm sorry, my device is I9305. I tried downloading firmwares for my device and got a PASS status at Odin, but still stuck at Samsung S3 screen after auto reboot. My device also is not locked to a carrier.
Any other options please. Thanks again.
You need to flash the i9305 firmware. I9300 and I9305 are two totally different phones with totally different firmware. What or who on earth made you believe that I9300 firmware would work on an I9305..
That's the equivalent of a man dressing in womans clothing and saying "I didn't realise I don't have a vagina"..
Beamed in by telepathy.
shivadow said:
You need to flash the i9305 firmware. I9300 and I9305 are two totally different phones with totally different firmware. What or who on earth made you believe that I9300 firmware would work on an I9305..
That's the equivalent of a man dressing in womans clothing and saying "I didn't realise I don't have a vagina"..
Beamed in by telepathy.
Click to expand...
Click to collapse
I've already downloaded 2 firmwares for I9305 and used Odin, and I got a Fail status on the first one while the other one I got a Pass but still not working. Do I need to download more firmwares? Do I need to choose what country I have to download even if my device is not locked to a carrier?
shivadow said:
You need to flash the i9305 firmware. I9300 and I9305 are two totally different phones with totally different firmware. What or who on earth made you believe that I9300 firmware would work on an I9305..
That's the equivalent of a man dressing in womans clothing and saying "I didn't realise I don't have a vagina"..
Beamed in by telepathy.
Click to expand...
Click to collapse
I've already downloaded 2 firmwares for I9305 and used Odin, and I got a Fail status on the first one while the other one I got a Pass but still not working. Do I need to download more firmwares? Do I need to choose what country I have to download even if my device is not locked to a carrier?
Sorry this is just my first time to do something on phones, I was just advised by a friend to get help here on this site.
If you get a pass after flashing with Odin, make sure to perform a factory reset before booting the phone for the first timer with the new ROM.
audit13 said:
If you get a pass after flashing with Odin, make sure to perform a factory reset before booting the phone for the first timer with the new ROM.
Click to expand...
Click to collapse
Exactly, but usually you must flash, wipe, flash again to get rid of any old data.
Beamed in by telepathy.
audit13 said:
If you get a pass after flashing with Odin, make sure to perform a factory reset before booting the phone for the first timer with the new ROM.
Click to expand...
Click to collapse
Hi Audit,
How can I get to factory reset option before booting? Thank you.
Try this:
open Odin and uncheck everything excepf f.reset time;
flash the stock ROM;
when you see the word "reset" in the status window, remove the USB cable from the phone, remove the battery, wait about 5 seconds, replace the battery;
boot into recovery mode by pressing the home, volume up, and power button. When the phone starts to boot, let go of the power button but not the home or volume button;
when the phone boots into recovery, perform a factory wipe; and
reboot the phone.
audit13 said:
Try this:
open Odin and uncheck everything excepf f.reset time;
flash the stock ROM;
when you see the word "reset" in the status window, remove the USB cable from the phone, remove the battery, wait about 5 seconds, replace the battery;
boot into recovery mode by pressing the home, volume up, and power button. When the phone starts to boot, let go of the power button but not the home or volume button;
when the phone boots into recovery, perform a factory wipe; and
reboot the phone.
Click to expand...
Click to collapse
Just to add, removing the battery and replacing it may cause the phone to boot automatically. In this case just pull the battery again and when you reinsert it the screen should stay black. If not, keep doing it. THEN you can safely get to recovery.
When you get the blue "pass" in odin the phone should reboot automatically. If it doesn't just wait 10 seconds and pull the cable, then pull the battery or hold the power button for about 20 seconds.
Beamed in by telepathy.
shivadow said:
Just to add, removing the battery and replacing it may cause the phone to boot automatically. In this case just pull the battery again and when you reinsert it the screen should stay black. If not, keep doing it. THEN you can safely get to recovery.
When you get the blue "pass" in odin the phone should reboot automatically. If it doesn't just wait 10 seconds and pull the cable, then pull the battery or hold the power button for about 20 seconds.
Beamed in by telepathy.
Click to expand...
Click to collapse
Hi guys,
I tried again just now to flash with Odin but unfortunately I'm getting a Fail status.. see below..
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I9305XXUEMKC_2051278_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I think my phone is completely bricked because previously it is showing battery charge when i plug it in but now the screen shows zigzag white & gray colors. Anything else I can do? Thanks again.
Try another *good quality* usb cable. * = not a cheap crap cable, one supplied with a device.
As the last port to call, flash a pit file for your specific model.
In all honesty I'll tell you that the pit file may break your phone permanently (most likely) or it could just as easily fix it. The partition information table is "missing" and usually indicates hardware failure. The 'fuzzy screen' is another indicator of a totally buggered phone.
Beamed in by telepathy.
Related
Hello,
I had a working setup with CM9 nightly 20120618, Siyah kernel 3.3.2 and LPX modem.
Due to phone call cuts, which seemed to be a known problem with the LPX modem, I tried to install LPS modem with RomManager premium.
I didn't watch my phone during the whole process, so I don't know if LPS install went successful. I guess it doesn't : I usually had to manually disable signature verification in CWM to be able to flash zip files.
I found my phone with a lighty flashing screen, as if backlighting was switching on and off on a black screen. I pulled off the battery, removed SD and SIM, and tried normal boot, boot to recovery and boot to download using the buttons combo : nothing works, I get the "GALAXY SII GT-I9100" screen and then the flashing black screen. If i press the home button while the screen is flashing black, it starts flashing white, and that's all.
I don't know what I can do now. Any help would be greatly appreciated...
Thank you
OK. Firstly, CWM & Rom Manager on the same phone is asking for trouble. Rom Manager does not play nice with CWM; has been known to cause bootloops, break recovery & cause 'soft bricks'. So if you're going to use Siyah (or any other kernel with CWM) with CM9, either freeze or uninstall Rom Manager.
Your OP is a bit vague, are you saying you have bootloop ? If you are, I'd do a factory reset in the first instance. If that doesn't work, I'd flash CM9 Resurrection in Odin, then flash latest CM9 nightly (read/follow the instructions in the CM9 discussion thread). From there, you can then flash Siyah if you want. And if you do use CM9 & Siyah again, don't forget to freeze/uninstall Rom Manager.
If you don't want to use CM9 anymore & the reset doesn't work, flash a stock rom (GB or ICS; up to you) in Odin, and go from there. That will give you a clean slate.
Now, if you don't have a bootloop & something else is happening to your phone, clarify exactly what your phone is/isn't doing & can/can't do (does it boot, do you have recovery, do you have download mode), and we can look at it further.
Many thanks for the fast help.
Searching XDA for solutions I had understood that CWM and RomManager doesn't get on very well. I won't make the same mistake again, I promise !
But now my problem is to get back in control of my phone.
To clarify the situation, I don't know what to do because :
* If I try a regular power on, I can see the "GT-I9100", and then a flashing black screen. It seems to flash for ever, but when I press the home button several times it flashes white/black, seems for ever too.
* If I power on pressing volume up, same thing
* If I power on pressing volume down, same thing
So that's not really a bootloop I think since I only see the "GT I9100" screen once.
I discovered a new thing : if I plug the power cable, I have the battery icon on the screen for a few seconds as usual, and then again the flashing screen.
So I wold be VERY happy if I could flash any rom, stock, CM9 of whatever, but as I am unable to go to download mode nor to recovery I don't know how to flash :crying:
Problem solved.
I'll look very noobish on this : I had forgotten to press the home button, that's why I couldn't go to download mode. Flashed CM9 resurrection with odin, then LPS modem, 20120622 nightly, and siyah 3.3.2 with recovery.
Then I freezed RomManager with titanium backup to avoid making the same mistake again.
My phone is back !
Good job sorting it out yourself like that. Glad you got it sorted ;-)
Hi,
Unfortunately i am one of the few who made the same mistake of having both CWM and Rom Manager. Same issues were experienced.
Now, i tried following the steps provided.
1. Downloaded RR cm9
2. Flash via odin
now the problem is i am stuck @
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cm-9-20120420-ODIN-galaxys2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003> NAND Write Start!!
<ID:0/003> Sbl.bin
Now i don't know what to do. it's been sitting here for around 20-30mins now w/ no signs of progress. Please help.
Well, just disregard. Took a risk by powering the device down and redoing the flash process. Changed the port and used a mobo port and it all worked.
Sent from my GT-I9100 using xda app-developers app
I have my S III for two and a half months. And today it started to boot loop. The phone was working and I leave it on the table. After few minutes I noticed that the phone is in boot loop.
This is my second android phone. Before the S III I had Desire. I have experience in rooting with the Desire (use it without root only 2 months and own it for 2 years). Also while flashing it many times I had boot loops on it -> re-flash always worked.
The S3's situation - it is in boot loop, when I try to start the stock recovery (volup+home+pwr and not releasing the) the phone starts to boot loop as long as I keep the buttons pushed. When I release them the phone stays in booting screen (Samsung logo) - same as I just try to start it. When I put it in download mode (voldown+home+pwr) it works and asks me if I want to continue.
Is there anybody with experience whit the same problem? And should I try to flash the stock rom from SGS3 ToolKit or to use the warranty and let the shop to fix it (probably will hold my phone for a month)?
shiSHARK said:
I have my S III for two and a half months. And today it started to boot loop. The phone was working and I leave it on the table. After few minutes I noticed that the phone is in boot loop.
The S3's situation - it is in boot loop, when I try to start the stock recovery (volup+home+pwr and not releasing the) the phone starts to boot loop as long as I keep the buttons pushed. When I release them the phone stays in booting screen (Samsung logo) - same as I just try to start it. When I put it in download mode (voldown+home+pwr) it works and asks me if I want to continue.
Is there anybody with experience whit the same problem? And should I try to flash the stock rom from SGS3 ToolKit or to use the warranty and let the shop to fix it (probably will hold my phone for a month)?
Click to expand...
Click to collapse
One boot to recovery Vol Up + Home + Power release immediately on splash screen .
No recovery then choice is return to service .
Or flash a stock rom via Odin from the stock rom threads .
jje
release the power vol up and power buttons as soon as you see android while entering recovery. Once you do that try factory reset.
Note: You will lose all your data on internal SD (pics, images etc)
If you want to save data first flash CWM then enter recovery and factory reset. You will be able to save pics, images, music etc by doing so (apps will still be removed)
JJEgan said:
One boot to recovery Vol Up + Home + Power release immediately on splash screen .
No recovery then choice is return to service .
Or flash a stock rom via Odin from the stock rom threads .
jje
Click to expand...
Click to collapse
Vol Up + Home + Power * *release immediately *on splash screen (Samsung logo) -
Stays on spash screen until I pull out the battery. No android logo is displayed.
If I try to flash stock rom via odin is it possible the service to deny my warranty?
shiSHARK said:
Vol Up + Home + Power * *release immediately *on splash screen (Samsung logo) -
Stays on spash screen until I pull out the battery. No android logo is displayed.
If I try to flash stock rom via odin is it possible the service to deny my warranty?
Click to expand...
Click to collapse
Okay follow the steps as mentioned:
Step 1: Download the stock firm ware for your region via sammobile.com/checkfus
Step 2: Open Odin 3.04
Step 3: Put your phone in Download mode
Step 4: Connect to PC
Step 5: Select the firmware (unzip it to get the .tar file if it is a .zip file) as pda..dont touch anything else
Step 6: Click Start and wait till the rom is flashed and your device reboots
Step 7: If the phone is stuck at boot screen after the flash, press vol up+menu+power untill you see a green droid..release immediately
Step 8: Clear Data+cache..you will loose everything on your internal sdcard
Step 9: Reboot
Now if you face any problem in any of the steps mentioned above..tell us which step and what is the error you get...
flashing stock will not void your warranty but the stock rom should be specific to your region..with correct CSC..
zoot1 said:
Okay follow the steps as mentioned:
Step 1: Download the stock firm ware for your region via sammobile.com/checkfus
Step 2: Open Odin 3.04
Step 3: Put your phone in Download mode
Step 4: Connect to PC
Step 5: Select the firmware (unzip it to get the .tar file if it is a .zip file) as pda..dont touch anything else
Step 6: Click Start and wait till the rom is flashed and your device reboots
Step 7: If the phone is stuck at boot screen after the flash, press vol up+menu+power untill you see a green droid..release immediately
Step 8: Clear Data+cache..you will loose everything on your internal sdcard
Step 9: Reboot
Now if you face any problem in any of the steps mentioned above..tell us which step and what is the error you get...
flashing stock will not void your warranty but the stock rom should be specific to your region..with correct CSC..
Click to expand...
Click to collapse
There is the log from odin:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXALF2_I9300GBLALF1_I9300XXLF2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
There are few pit files in the zip with the odin but I don't know which one to use:
GT-I9300_mx_20120220.pit
GT-I9300_mx_20120322.pit
GT-I9300_mx_20120329.pit
M0_20120220.pit
mx.pit
Also tried with latest pit this is the log file:
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXALF2_I9300GBLALF1_I9300XXLF2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Flash via 3 file method..search for the method in the threads..
It does not look good..flashing the pit file is dangerous
Sent from my GT-I9300 using xda app-developers app
De tick the Re-Partition checkbox and try? But your definately going to have to re flash using Odin
Guys thanks for your help. After few unsuccessful attempts to flash with odin, I returned the phone to customer service, and now I'll wait them to fix it. Now I'm with my old Desire until they fix my SGS 3.
shiSHARK said:
Guys thanks for your help. After few unsuccessful attempts to flash with odin, I returned the phone to customer service, and now I'll wait them to fix it. Now I'm with my old Desire until they fix my SGS 3.
Click to expand...
Click to collapse
Hi shiShark,
Any luck when you returned to customer service? I seem to have exactly the same problem.
Out of interest, did your phone show as system Custom in the recovery screen? - Similar to you, I have not rooted or flashed my phone but it says sytem:Custom on the recovery screen and customer service refuse to fix it under warranty.
Thanks.
Will
Hi guys,
My friend gave me her S3 to fix because there was a problem with it. She said that she was on YouTube when it froze, she took the battery out and when it turned back on, a message came up saying "Encryption Failed. Unable to complete encryption due to interruption. Perform factory data reset (erasing all your data) before use....." There's a button that says "Reset Device" but when I press it, it doesn't do anything. She has NOT rooted her device or tampered with it at all, nor has she tried to encrypt her data, so this is quite unusual. I tried to put it into Recovery Mode so I could perform a factory reset by holding power, Vol Up and Home. As I hold these buttons, a message pops up at the bottom of the screen saying "Device storage is full. Delete some items", although my friend says that she had recently factory reset her phone and there isn't much stuff on her phone. The phone then restarts as it should. It shows the android with the spinning shape thing in his stomach. Then it stops and the phone restarts again back to the "Encryption Failed" screen. I have tried many times to get into Recovery Mode but it wont work. I researched online and found that others say that they also cannot access stock recovery but can access TWRP and CWM. I can get into Download Mode, so it thought that maybe I could try to install one of the two recovery modes. I first tried to root the device using Odin3, however, it keeps failing.
This is what it says:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-m0-m0xx-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
On the device it says
ODIN MODE
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
I really don't know what to do and would appreciate it very much if someone could help me. Thanks in advance
Hey I have a samsung galaxy s5 and currently have the same problem did you ever figure a way to fix this?
Albercurkey said:
Hey I have a samsung galaxy s5 and currently have the same problem did you ever figure a way to fix this?
Click to expand...
Click to collapse
No, I didn't. She ended up buying a new phone. Sorry
HI All
I'm wondering if you guys have seen similar problem. I have currently rooted stock ROM on my Mega but want to install CWM so I can take a backup of the system and try out CyanogenMOD11.
Yet, when I try flashing CWM with Odin it looks like this:
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> recovery.img
<ID:0/012> NAND Write Start!!
<ID:0/012> RQT_CLOSE !!
<ID:0/012> RES OK !!
<ID:0/012> Removed!!
<ID:0/012> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
At this point phone reboots and when I go to recovery - there is no CWM
I will be grateful for any suggestions.
Thanks
I would suggest you try this http://goo.im/devs/philz_touch/CWM_Advanced_Edition/meliusltexx/philz_touch_6.25.0-meliusltexx.tar.md5 assuming you have the GT-I9205 of course.
Kangburra said:
I would suggest you try this _link_ assuming you have the GT-I9205 of course.
Click to expand...
Click to collapse
I will try that, thanks for suggestion :good:
So I tried the above but have same thing happening.
Everything looks as if it's working OK. Odin picks up the phone, I load the image in PDA.
Have Auto Reboot and F.Reset Time enabled (only).
I hit the start button and it's VERY fast - literally few seconds and I get blue RESET! in the top box in Odin.
What's interesting is that after another two minutes Odin will change to PASS!
But that's looong after my phone booted back to normal operation mode, it will also change to PASS even if I have disconnected my phone
Any suggestions anyone?
==== UPDATE ===
What I also noticed is that after I boot to recovery I'm getting ERROR and NO COMMAND - they will flash on the screen and instead of usual Android Robot I have one on it's side with red exclamation mark over it.
No Command and this point is displayed below the "robot".
This is really irritating
One thing when you are flashing a custom recovery on the mega is once you are done flashing with odin you MUST reboot the phone directly into the recovery mode again for like CWM to appear otherwise if you do not do this the stock recovery will be back, this only has to be done once when you first flash a custom recovery..then it will be okay after that.
And with odin that does the same thing for me it says RESET but it still works and after it will say PASS when the phone is disconnected already, not sure why odin does this but seems to have no effect on the flashing part...hope this helps you out.
starmaster10 said:
One thing when you are flashing a custom recovery on the mega is once you are done flashing with odin you MUST reboot the phone directly into the recovery mode again for like CWM to appear otherwise if you do not do this the stock recovery will be back, this only has to be done once when you first flash a custom recovery..then it will be okay after that.
And with odin that does the same thing for me it says RESET but it still works and after it will say PASS when the phone is disconnected already, not sure why odin does this but seems to have no effect on the flashing part...hope this helps you out.
Click to expand...
Click to collapse
That was is!
Thanks for pointing in the right direction.
I've all the same options in Odin but when it auto-rebooted my phone I have quickly pressed the the buttons for going to recovery and that worked. When powering off from recovery I was given an option to disable stock recovery and now it's all as intended.
THANKS!
Ch3rub said:
That was is!
Thanks for pointing in the right direction.
I've all the same options in Odin but when it auto-rebooted my phone I have quickly pressed the the buttons for going to recovery and that worked. When powering off from recovery I was given an option to disable stock recovery and now it's all as intended.
THANKS!
Click to expand...
Click to collapse
You are welcome.
Ch3rub said:
So I tried the above but have same thing happening.
Everything looks as if it's working OK. Odin picks up the phone, I load the image in PDA.
Have Auto Reboot and F.Reset Time enabled (only).
I hit the start button and it's VERY fast - literally few seconds and I get blue RESET! in the top box in Odin.
What's interesting is that after another two minutes Odin will change to PASS!
But that's looong after my phone booted back to normal operation mode, it will also change to PASS even if I have disconnected my phone
Any suggestions anyone?
==== UPDATE ===
What I also noticed is that after I boot to recovery I'm getting ERROR and NO COMMAND - they will flash on the screen and instead of usual Android Robot I have one on it's side with red exclamation mark over it.
No Command and this point is displayed below the "robot".
This is really irritating
Click to expand...
Click to collapse
I got same problem when i flashed cwm by phil with odin, what i did is to uncheck autoreboot in odin so after odin finish flash recovery image you need to turn off manually by long pressing power button, and then just boot into recovery, reboot system now and select yes disable stock recovery when prompted by cwm.
Sent from my GT-I9205 using XDA Free mobile app
This does not work for me?
SPH-L600 (Sprint) Galaxy mega
Android: 4.2.2
Baseband: L600vpubne4
Build: KOT49H.L600VPUBNE4
Hey guy,
SM-G925F is my Galaxy S6 Edge model. The phone is stucks on first boot logo and I cant turn the phone off, unless the battery discharges. I can enter the download mode but in odin the process doesnt want to go further that this :
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3604 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
It stays on that and nothing happens. I cant enter recovery while holding the buttons for it (up, home n power). Tried in Kies "Firmware upgrade and initialization" but it ask for the Serial number which I dont have (I dont have the box of the phone anymore). I might be able to find the IMEI but would it work instead the serial number?
Any ideas what else to try? The phone was working fine, I fall asleep with it and when I woke up it was stuck on the booting logo, no idea what I could have done to it.
Thanks n advance
$$ [email protected] ViNcI $$ said:
Hey guy,
SM-G925F is my Galaxy S6 Edge model. The phone is stucks on first boot logo and I cant turn the phone off, unless the battery discharges. I can enter the download mode but in odin the process doesnt want to go further that this :
It stays on that and nothing happens. I cant enter recovery while holding the buttons for it (up, home n power). Tried in Kies "Firmware upgrade and initialization" but it ask for the Serial number which I dont have (I dont have the box of the phone anymore). I might be able to find the IMEI but would it work instead the serial number?
Any ideas what else to try? The phone was working fine, I fall asleep with it and when I woke up it was stuck on the booting logo, no idea what I could have done to it.
Thanks n advance
Click to expand...
Click to collapse
Which version odin? Are you trying to flash stock?