hello i have a bricked mipad 1 and wanted to know if someone could help me out.
where i stand is:
-mipad is dead (no recovery, no fastboot) only shows a red led blink when i plug it to PC
-when i turn the mipad with usb to pc i dont need to do short circuit on sd card for PC to detect it
-pc detects the mipad with nvidia boot recovery
-when i try to flash it it shows this
ttp://i.imgur.com/pi68yuj.png
thanks
Have you recovered your tab?
I think you should rename firmware folder to short name and keep it on root directory on pc ( to have shortest path) and these should not be any spaces in names/ path of the folder. Try it out and reply. I may not be able to help you further but instructions i mentioned, i had read somewhere on forum. So your reply/ confirmation may help someone else out.
Related
For all of you out there having Iconia B1-710 in boot loop or hard bricked, this is the way to fix it.
I'm not responsible to any damage you got when following the instructions.
!!!YOUR WARRANTY WILL VOID!!!
This will fix SPFT errors 2004, 6010, 1010.
At this moment I'm not able to upload files so contact me over email: [email protected]
First of all, read this entire post and make sure that you have MediaTek DA USB VCOM drivers installed.
If not do this:
1. Extract all files from the archive and run every program as administrator.
2. Disconnect the tablet from the PC, remove the back cover and pull off the battery connector.
3. Open device manager and expand Ports (COM&LPT) selection
4. Connect the tablet to the PC and right click on any new shown device. If it's reconnecting don't worry, you just need to be fast and right click it and select Update Driver Software.
5. Click on Browse my computer for driver software and click Let me pick from a list of device drivers on my computer.
6. Uncheck Show compatible hardware and from the shown list find and select only MediaTek DA USB VCOM. If MediaTek DA USB VCOM is not shown you didn't installed the drivers correctly.
DISCONNECT THE TABLET FROM THE PC AND DO NOT PUT BACK THE BATTERY CONNECTOR
1. Now open SPFT and select the scatter file.
2. Click on window and then Write memory
3. In memory settings select EMMC.
4. Click Open Raw Data and select secuoff.img
5. In Begin address write 0x1F88000 and in Container Length write 0x427100
6. Click Write memory and connect the tablet. Green circle should appear.
7. Now go back to download selection and make sure that everything is selected (including preloader and dsp_bl).
8. Press download. If everything was good you should see a green circle.
9. Remove the USB cable and put the battery connector back and back cover to place.
DO NOT TURN IT ON. CONNECT IT TO CHARGER AND LEAVE IT ABOUT 15 MINUTES TO CHARGE.
how to fix tab
i have acer b1-710 tablet that keeps restaring can i use this guide to fix it ?
Hi Daniel !! First of all, THANK YOU !!
I've used this guide to revive my HARD BRICKED tablet Acer Iconia B1-A71 and it worked like a charm !!!
I followed step by step your guide using B1-A71 original stock firmware's files.
So I came back to your post just to say THANK YOU VERY MUCH SIR !!!
I know this is an old thread, but you saved my life and it's never late to say thank you
Greetings,
Seba
hey....the firmware i downloaded does not contain scuofff.img file...can u give a link of a firmware that has one ??
I have Iconia B1-711 in boot loop (I think hard bricked) .
I think i have the corect drivers and the "SP_Flash_Tool_v5.1628"
Dose anyone have the scatter , the secuoff.img and the other files ?
Can Anybody give the required files please
secuoff file
Hi, I trying to follow your instructions but where can I find that secuoff.img file.
hello, could someone pass me the necessary files for the B1-710, thanks
guys i have big problem.
I flash this rom via twrp and add to the tree su and some other files like xpose.
After that I have brick my device.
When I push power it shows only for 1 s miui logo and after that red led is blinking.
When i plug it to my computer it shows that it couldn`t recognize the usb driver, when i go to the menager it shows that it is decrypted).
I could turn on fastboot mode but it not helping beacuse my comp doesn`t see device in fastoob/adb mode.. (i have good drivers - i do a lot of diferent flash by fastboot).
Maybe you have some advice for my problem. I loose TWRP ;( .....
I trie to disconect battery (open the body) but it not help.
Please hepl me!
http://www.tinypic.pl/y2rjc02j3h7u
Dinosek said:
guys i have big problem.
I flash this rom via twrp and add to the tree su and some other files like xpose.
After that I have brick my device.
When I push power it shows only for 1 s miui logo and after that red led is blinking.
When i plug it to my computer it shows that it couldn`t recognize the usb driver, when i go to the menager it shows that it is decrypted).
I could turn on fastboot mode but it not helping beacuse my comp doesn`t see device in fastoob/adb mode.. (i have good drivers - i do a lot of diferent flash by fastboot).
Maybe you have some advice for my problem. I loose TWRP ;( .....
I trie to disconect battery (open the body) but it not help.
Please hepl me!
Click to expand...
Click to collapse
This might help you http://en.miui.com/thread-235865-1-1.html
http://en.miui.com/thread-274589-1-1.html good luck
bigest problem i think is that that my computer can`t recognize phone. all the that it show that he can`t recognize usb. device.
even I want to use test point method but it doesn`t work for me I think - I want to connect first and last pin (it`s correct??)
in my device menager i have
http://www.tinypic.pl/y2rjc02j3h7u
I try I think every thing. With my computer and another. Bouth of them doesn`t recognize phone. I could only go to the fastoboot mode but comp don`t see it.
I try even deep flash...
Try to install driver mi
Sent from my Redmi Note 3 using Tapatalk
What I do
Change computer , reinstall drivers, unsuscribe drivers
Disconnect battery, di the test point
The bigest problem I thing right know I that that any computer doesn't see it. I do not understand why I always shows unknown device and info about description problem. I check it in one computer that one company change systems in selling xiaomi ( for sure good drivers)
I rescue my phone. What happend. I don't know how but my USB port was broken after last flashing by twrp. I change USB port and miflash start to see my device (funny is that computer doesn't saw it).
I unlock my device and flash in miflash stable miui.
Wysłane z mojego Redmi Note 3 przy użyciu Tapatalka
Hello (i know my english is terrible but i need help)
i have bought not long ago BV6000 and i use format option in SPflash tool (not exept bootloader, i pick format all). After this phone is dead. No respond for charging, not respond when i connect him to computer. When i connect phone to computer and push volume + button computer start see phone for 1 second, then again he disappear for +-5 second and next time he start seen and again, again....
Is any method to bring back to life this phone or only producer can help me?
When i format phone i lost IMEI numbers or IMEI should be still saved in phone?
Emik3 said:
Hello (i know my english is terrible but i need help)
i have bought not long ago BV6000 and i use format option in SPflash tool (not exept bootloader, i pick format all). After this phone is dead. No respond for charging, not respond when i connect him to computer. When i connect phone to computer and push volume + button computer start see phone for 1 second, then again he disappear for +-5 second and next time he start seen and again, again....
Is any method to bring back to life this phone or only producer can help me?
When i format phone i lost IMEI numbers or IMEI should be still saved in phone?
Click to expand...
Click to collapse
When you do the volume up thing, in fastboot, do you see your device?
RAZERZDAHACKER said:
When you do the volume up thing, in fastboot, do you see your device?
Click to expand...
Click to collapse
Yes computer see my device but only for 1 second. When i hold volume up all time computer see my device for +-1 second and then my device disappear for +-5 second and then again from begining 1 second see......
When i push volume + for short time, computer see device for 1 second and then device disappear.
And when i try flash my phone by using SPflash tool, proces start and get error at start cause device disappear.
This phone have Android Marshallow.
Oh i read some topics. When i try run device in fastboot mode the device dont turn on, nothing happend.
Emik3 said:
Yes computer see my device but only for 1 second. When i hold volume up all time computer see my device for +-1 second and then my device disappear for +-5 second and then again from begining 1 second see......
When i push volume + for short time, computer see device for 1 second and then device disappear.
And when i try flash my phone by using SPflash tool, proces start and get error at start cause device disappear.
This phone have Android Marshallow.
Oh i read some topics. When i try run device in fastboot mode the device dont turn on, nothing happend.
Click to expand...
Click to collapse
Alright, with this one second, have the "fastboot reboot-bootlaoder" command ready and then, when it sees it, immediately hit enter. Report results.
RAZERZDAHACKER said:
Alright, with this one second, have the "fastboot reboot-bootlaoder" command ready and then, when it sees it, immediately hit enter. Report results.
Click to expand...
Click to collapse
Dam, i cant add picture.
When i try use this command after installing adb i see in cmd waiting on any device and when i connect phone nothig happend, still waiting.
I will try on another computer. I have computer with windows 10, in cmd i have waiting for device after write "fasttboot reboot-bootloader" command but phone is seen like communication port (com 1). Anyway i have instaled drivers for this phone (for normally working, and they are not drivers for this phone on windows 10)
Before i have pick in SPflash tool:
Format--->auto format flash---->format whole flash
so i think bootloader is formated and he need recover or reinstal
On computer with windows 7 is this same but in device menager he see phone named "MTK USB Port" in cmd after use reboot bootloader command cmd all time waiting for device.
I have installed MediaTek PreLoader USB VCOM Port but device dont use this drivers, when i connect the device use MTK USB Port or is added like new port.
Yup, but i dont want firmware update but i need firmware repair cause i get phone with bugged firmware and factory default settings not help.
Blackview BV6000 Flashing Android 7.0
Follow the link below if you wish to #FLASH your #BLACKVIEW #BV6000 with the latest official #Android 7.0 #NOUGAT firmware..
https://dreamworks75.blogspot.in/2017/08/rom-flashing-guide-blackview-bv6000.html
I own the TV BOX TRANSPEED_H616 (Allwinner H616, Arm Mali-G31 MP2, Android 10, 4/64 GB).
I would like to root but can't. I can't even connect the device to the PC.
When I connect it with the USB-OTG cable, in the device manager it shows "USB device unknown (device descriptor request failed)" and I cannot find the drivers. Can someone help me?
Thank you
i have same problem.
After several attempts I managed to enter recovery mode.
I would like to root the device now but I don't know how to do it.
Can anyone help me?
Thank you
Since no one can help me, I want to try to summarize everything I understand using this device. The first thing to do is to enable the developer option and then check USB DEBUG and USB0. At this point, by connecting the USB cable to the OTG input, the device is recognized by the PC as MPT. By opening the Phoenixsuite or Powershell application from the SDK folder you can send commands to the device, you can access the custom recovery and nothing more. Unfortunately, the bootloader cannot be unlocked, and the firmware cannot be changed either through the PC or even with SD. When entering Bootloader mode the PC loses connection with the device because it changes to an unknown device without drivers. Also with Powershell if you want to unlock the bootloader this is not possible because when you send the command "./fastboot flashing unlock" it returns the message "Failed". By inserting the SD card with the firmware and starting the device with a stick inserted in the AV input and the electrical AC connector, a red indicator lights up on the display and the flashing does not start. Clearly in these conditions it is impossible to think about rooting the device. I hope that in the light of what has been said, someone can give me some research ideas or useful advice. Finally I apologize for my English (from Google)
Hello, recently I bought a transpeed X88 pro s (from transpeed official) , h616, 4gb+128gb with android 10.
But it is a fake, it's a board with hacked firmware (dispute is open) , it only have 64gb ( chip Samsung Klmcg2ketm), it warm so much (more than 90°C) with faults on gpu (changing colors, slowly,...), only way to work is with open box or fan.
Anyway, I'm in the way to root and change firmware too.
It's rooted by default, with supersu 1.82 work well and permit restart to bootloader (with reset button was impossible).
I will inform about progress.
I have a T9 4GB/64GB TV BOX (RK3328) TV stick, it got bricked. I tried all method to get it boot in maskrom mode but no luck. was flashing firmware its failed.
now my box not turning on.
I used flash tool to flash T9-4_64-RK3328-6255-v9-1228_AndroidTVBox image file. I attached flash log file and board image
I have no ideas, anyone please help!
Same Issue with me. it is dead, if you have found any solution just tell me
I was able to get it in maskrom mode by shorting these point
zee95 said:
I was able to get it in maskrom mode by shorting these pointView attachment 5661685
Click to expand...
Click to collapse
Hi @zee95 , I have the same problem, I bricked it trying to flash it, now it doesn't turn on not even the boot led nor recognized by PC when I plugged it with usb
Can you guide me please with the steps you followed to unbrick, how did you shorten those points. Thanks in advance @zee95
How you are flashing rom ?
The one i used with an incorrect firmware was Factory Tool v 1.46.
After that the box never turned on, nor even the t9 boot screen or the blue front leds. Also unable to been recognized by any flash tool.
I have tried with SD Card with firmware (using Rockchip Create Upgrade Disk) , hit reset button and power on, but nothing.
Also tried shortening with a clip and needle the two points you mentioned in the picture and plug the power cable at the same time but nothing.
Regards
Having same problim
when ever i connect to pc its in maskrom mode and cant exit from it
plz help