Hi,
I have a problem. A tablet I have been using for the last four years suddenly could not start anymore. It could not boot. The volume +/- and power to enter recovery is not working.
Here are the specs of the tablet.
MSI Enjoy 71
Android 4.11 (was)
AML8726
8GB RAM
When I connect it to the computer it was recognised as M6-Chip. After browsing through XDA, I installed the WorldCup Driver and AML USB Burning Tool. The tablet is now detected as WorldCup Device. I run AML USB Burning Tool and it detected the connection.
I downloaded the firmware upgrade from MSI's website (MSIM767ND_200_20130415_V2.0.4_4.1.1).
It have these files in the root directory.
factory_update_param.aml
uImage_recovery
update.zip
I unzipped the update.zip and found in the update.zip some img files as follows.
aml_logo.img
boot.img
bootloader.img
logo.img
I tried each file and keep getting "Parse Burning Iamge fail".
It's giving me a headache since I can't find any solution in the forum. I know some of you will say just get a new one. But I am used to it and if it can be saved I hope to do it.
Thanks in advance.
Related
I have an old multipad PMP3384B with seriously old and slow Android 2.3. I tried to update it following the process below and using a rooted image.
What you need:
-get Rockchip Batch Tool from HERE (contains USB drivers)
-get a firmware:
a) PMP3384BRU_20111206_V1.1.9_root -prerooted image, no other changes
b) PMP3384BRU_20111206_V1.1.9_root_607Mb_free - 607 MB for /data, prerooted, Golauncher, Gokeyboard, Adobe Reader, CoolReader, Dolphin browser HD, ButtonSaviour- only for RockChip Batch Tool flashing
How to flash:
1. fully charge your MultiPad
2. backup internal flash- it will be erased
3. unpack Rockchip Batch Tool and launch it as admin
4. press and hold Reset (on the back), plug USB cable, release Reset
5. there should be a popup asking for drivers- they are placed in Rockchip_Batch_Tool_v1.4\drivers\[windows version]. If there is no popup go to Device Manager and install drivers
6. load firmware .img file to Rockchip Batch Tool and click Update button
After I completed this process rockchip batch confirmed that the update was successful with no errors but I can no longer power up the tablet. I have tried the reset button but no joy. I also tried following the process again as the tablet is still being detected by Rockchip batch tool when plugged into my pc via usb. I'm downloading the original firmware from the prestigio site now so once that is done I will try restoring it.
Any other ideas would be much appreciated
EDIT : Problem resolved, reinstall of firmware from prestigio site worked.
find my post on this topic http://forum.xda-developers.com/showthread.php?t=1403956 hope it will help you !
[HELP] Bootloop after flashing: recovery-clockwork-6.0.3.1-p4.zip -> NOOB!!!!
I`ve just tried everything related to this issue on this forum!!
Before the bootloop i had access to the adb and fastboot features by usb debbugging (sdk manager) and stock recovery, etc...
With the Bootloop, now i can´t access to the stock recovery with the 1001 combinations of the buttons, removing the battery, pressing the volume button and then connect to the pc via usb, adb reboot, and so on and so on.... nothing works!!
The pc only recognizes via usb the Tab (1 second) asking for MT65xxPreloader, like a bootlooping asking for this controller. I´ve installed this controller and the bootloop remains - 1 second each boot...
Anyone can help me to solve this dead brick? Is is not possible make a startup disk via sd card like exists for windows, for example??
Without PC connection i don't see the solution.....
Thanks in advance!!
You will need to use mtk software to enter meta mode.
Sent from my A1-810 using XDA Premium HD app
KieranFoot said:
You will need to use mtk software to enter meta mode.
Sent from my A1-810 using XDA Premium HD app
Click to expand...
Click to collapse
Thanks for your answer!
My device can´t still enable to enter in meta mode. I tried MT6573, MT6577, MT6589 VCom driver, the SP Flash tool doesn´t locate the DA path for the function download scatter loading file.....
I followed this tutorial: http://forum.xda-developers.com/showthread.php?t=2206421&nocache=1, for windows Vista. It seems the controller is installed, but the SP flash tool or MTK tool doesn´t recognize my iconia A1-810.... I loaded the *.txt file: MT6577_Android_scatter_emmc.txt and marked all options ans appears a error: FLASHTOOL ERROR: S_FTHND_FILE-IS-NOT-LOADED-YET (5007)
I disconected the battery and when i connect usb to pc the driver apppear for 1 second with the Mediatek Preloader vcom controller and enter in loop again... appear and disappear on the PC Device Manager.....
I´m completely lost.. can you suggest something?
Thanks
flashtool error image attached
check it maybe will help, good luck !
I bought my Acer A1-810 it’s 2,5 months (from amazon). And few days ago I decided to root it. 1 hour later i realized that was not a really good idea, because i did not know much things about, and it was not as easy as I thought. and voila as a result : bootloop !
I tried different roms, different update.zips but got allways the same error : ” check.partition.size=[__PROP_UNDEFINED__] ”
I was desperate…I was at the point of resend it to Acer for repair. But last try was successful, I did it, I did !!! And there is how !
1. go to acer web page --->support--->drivers and manuels
2. choose your model acer a1-810
3. As my divece was bought in usa, my FW upgrade is AV052.RV26RC06.PA.CUS1 (in O.S ), download it !
4.when it’s done, you should unzip and should get update.zip separately.
5. Put update.zip on SD card
6.Put SD card in your device.
For next steps see the manuel of update
Please i need help.
On my phone Lenovo s820 was viber rom. I try to put different. And i downladed that rom form needrom page
[
LENOVO S820 - Update 13/08/2013 -- this version i install it with flashtool .The process came ok to the end,
After complete i can t turn on my phone any more.
I try it again but after that flash tool put me only message after red bar came to 100 %
BROM ERROR:S_FT-ENABLE_DRAM_FAIL(4032)
I try put several rom but evething is same phone is dead i cant turn him on -----
For all roms what i try to put -was the same story. I vant do nothing anymore.
When i connect phone (after bricking) with usb cable on computer it found MTK USB PORT(36). Not preloader.
I do it before flasing with flash toll others Lenovo phones and always was good. But now with this lenovo s820 something went wrong.
Please i need someone who have similar probem to help me find solution to unbrick my phone.
Thanks a lot.
sukisus said:
Please i need help.
On my phone Lenovo s820 was viber rom. I try to put different. And i downladed that rom form needrom page
[
LENOVO S820 - Update 13/08/2013 -- this version i install it with flashtool .The process came ok to the end,
After complete i can t turn on my phone any more.
I try it again but after that flash tool put me only message after red bar came to 100 %
BROM ERROR:S_FT-ENABLE_DRAM_FAIL(4032)
I try put several rom but evething is same phone is dead i cant turn him on -----
For all roms what i try to put -was the same story. I vant do nothing anymore.
When i connect phone (after bricking) with usb cable on computer it found MTK USB PORT(36). Not preloader.
I do it before flasing with flash toll others Lenovo phones and always was good. But now with this lenovo s820 something went wrong.
Please i need someone who have similar probem to help me find solution to unbrick my phone.
Thanks a lot.
Click to expand...
Click to collapse
If you put it to a wall charger does the phone respond?
UltraWelfare said:
If you put it to a wall charger does the phone respond?
Click to expand...
Click to collapse
No nothing,neither in wall with charger , Nothing --unresponsive.
Only sing is when i connect him with pc is in device manager MTK USB PORT(36). But few second is availabe then it turn of. And so on all the time. Turn on and turn of in device manager.
Please if you or someone know how to repair I'd be very grateful .
I m last 3 days trying to repair it but I can t .
Flashtool send me same message again.
I tried with backup from another s820 but nothing.Same story.
Is it main problem with mtk drivers or right rom?
Thnaks a lot
sukisus said:
No nothing,neither in wall with charger , Nothing --unresponsive.
Only sing is when i connect him with pc is in device manager MTK USB PORT(36). But few second is availabe then it turn of. And so on all the time. Turn on and turn of in device manager.
Please if you or someone know how to repair I'd be very grateful .
I m last 3 days trying to repair it but I can t .
Flashtool send me same message again.
I tried with backup from another s820 but nothing.Same story.
Is it main problem with mtk drivers or right rom?
Thnaks a lot
Click to expand...
Click to collapse
Have you checked out these 2 links [1] [2]?
UltraWelfare said:
Have you checked out these 2 links [1] [2]?
Click to expand...
Click to collapse
I try but nothing.
I have similar probelm as in this video
youtube.com/watch?v=hKYH7gkvrvY
but in my sitation is not happy end- Still error
pass levigati
I think that i m during my first flashing click on firmware/upgrade instead downlad.
Maybe is this main problem?
thnaks
I've seen the other thread in xda forum that solved this problem and it's because of the preloader file but thing is which preloader file that solved this DRAM failed problem. Anyone? Please.. share the link or files included the steps?
Solution that I've already try and end up error.
- try other S820 Stock ROM , load up in SP Flash tool and end up with same error "DRAM Failed"
- take out the batt. plug in back after hit the "download" button from SP Flash tool and at the same time plug onto usb while pressing power + vol. down @ both vol. button and end up with the same error.
p/s : in my case, the usb drive is well connected and recognize by my laptop/pc desktop and I'm pretty sure that this has nothing to do with the usb driver cause my laptops still can detect my phones (com port).
Problem Solved.
I've download several files and my phone turn on back. Follows below step if you're having same problem as mine.
Problem :
Phone is already update to a new version 4.4.2 Kitkat (don't know which or what rom since this phone is not belong to me) and from what owner tell me is that this rom that installed has no gapps and he tried to install the gapps.
after flashing it, phone become dead and won't boot even can't see the bootloader. Just nothing if you hold up the power + vol. down / up or power + vol. up and down.
When plug in phone to pc / laptop, phone is detected by Lenovo usb port or MTK usb port.
Solution :
*IMPORTANT* make sure you came from what version. (mine is 4.4.2 kitkat)
Things that you need -
sd card (just enough to put the required files), usb cable, SP Flash tool v3.1328.0.183, preloader.bin file, S820_ROW_S119_130922 files and S820 Multi language files.
1. Download all the requirement files.
S820 Custom Multi language and pre_install_rom v9 here
preloader.bin file here
S820_ROW_S119_130922 here (login and passwd can be found here)
2. Extract the S820_ROW_S119_130922 files and extract the target_bin.zip files.
Then extract the Pre_install_rom v9 and rename the folder as target_bins. After that,
extract the preloader.bin files and put it on the target_bin folder. (Don't worry as in target_bin folder already has the preloader_S820_ROW.bin (119kb) ). Done extract the files, check your phone either your machine detect it by name MTK usb port or Lenovo usb port. If it is MTK then we're good to go. ( If other than that, please uninstall any other lenovo driver that you already installed in your machine. Restart machine and check again whether your machine recognize it as MTK port or Lenovo usb port. ) When you done with this, unplug your phone from your machines and leave it aside.
3. Run the SP flash tool (admin rights) and select the MT6589_Android_scatter_emmc files that located in target_bin folder. Tick the DA DL with all checksum. Then copy Checksum files in folder target_bins and paste it on target_bin folder and on SP flash tool click download. Let it load for a moment until at the bottom of it (EMMC) you see "searching".
4. take out your batt. and plug in back then plug the usb cable to your machine and wait for the sp flash tool detect your phone and start the flashing process. After done flashing, now your phone has the CWM recovery. Unplug the phone from machine and leave it aside.
5. Copy the yaaki_v9_lenovo_S820_KITKAT_4.4.2_rooted files into your sd card and plug into your phone. Press and hold the power + vol. down + vol. up and wait until you see the Lenovo logo then you can see the CWM recovery. Go to install from sd card and select the yaaki_v9_lenovo_S820_KITKAT_4.4.2_rooted files and flash it. Wait until the process finished and after it finish installed, go back and reboot system now and choose NO for disable the CWM recovery flash.
6. Wait for around 2 - 3 mins. for the updated apps. Phone rooted + gapps + custom CWM recovery.
THANKS!!!
I can't describe how much i appreciate your post. I had the exact same problems as you did, I even used the some first rom to flash which made me problems. 3 days the phone was dead. Then I tried and did the exact from how you wrote in the last post and my s820 is live again.
:laugh::laugh::laugh::laugh::laugh:
Now I'm completly sure to update mi phone, thanks!
Please help
It has been asked to extract S820_ROW_S119_130922 and extract the target_bin.zip. Further you are asking to extract Pre_install_rom v9 and the rename the folder to target bin. And again you are asked to put the extracted preloader.bin to the target bin.
I’m quite confuse over this and so I would like to raise few questions.
1) To which target bin you are asking to put the preloader.bin file? ROM’s target bin or renamed (Pre_install_rom v9) target bin?
2) And in step 3 you are asking to choose MT6589_Android_scatter_emmc from target bin. Now please tell me which target bin I have to choose? If it’s from the renamed target bin (Pre_install_rom v9) then what is the use of extracting S820_ROW_S119_130922 and again the target_bin.zip? Or if it’s from ROM’s then what is the purpose of extracting Pre_install_rom v9?
Unsuccessful !! Not working.
Flashing was completed successfully. But unfortunately ended with just a flash in the screen. It doesn't start at all.
For device produce in 2014 you must download a new preloader 2014, extract it to ROM folder and remove the checksum.ini file, and flash using SP tool.
orangdayak said:
For device produce in 2014 you must download a new preloader 2014, extract it to ROM folder and remove the checksum.ini file, and flash using SP tool.
Click to expand...
Click to collapse
still ERROE 4302 DRAM FAIL
????
PLZ ANY BODY HELP??
ricco7 said:
Solution :
*IMPORTANT* make sure you came from what version. (mine is 4.4.2 kitkat)
Things that you need -
sd card (just enough to put the required files), usb cable, SP Flash tool v3.1328.0.183, preloader.bin file, S820_ROW_S119_130922 files and S820 Multi language files.
1. Download all the requirement files.
S820 Custom Multi language and pre_install_rom v9 here
preloader.bin file here
S820_ROW_S119_130922 here (login and passwd can be found here
Hello, can you, or somebody else, mirror the files used here? Needrom does not let me download them completely. Google Drive would be fine, thanks!
@bgdn2k7 @cesarkpt @sanads @ricco7
Click to expand...
Click to collapse
Do you know?
Still 4043 error.. yay. How many mtk this S820 have?
Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Tomaskaos said:
Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Click to expand...
Click to collapse
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
SubwayChamp said:
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
Click to expand...
Click to collapse
Thanks!!! It works!!!!
Just be very careful. The USB C connector port in the phone is very loose... so make sure you can hold the cable tight other wiser it will lose the connection and brick your phone. For me, I had to remove the Plastic cover to be able to hold the power cable tight!
Hi, could you help me please? I did your steps, but it is not working. Sp flash does all its job, shows the green sign, but the phone stills dead. What I noticed the usb connects with the phone, then it disconnects. I tried to install the drivers as the tutorials say like deactivating the driver signature enforcement, but nothig happens well.
Hello everyone;
I was trying to load a CM recovery file on my cell by using SP Flash tools and somehow bricked my Acer Z410 phone (carrier: Fido, 2 sim card slot) I do not know why afterwards, the cell turns white with a yellow strip down the middle. I have been able to have my computer recognize it after numerous attempts to flash firmware versions that I was not quite sure was the original. I had tried your site to load the firmware that seem to correlate to my cell configurations, but all of the links are dead. I ended up flashing with SP Flash tools firware version AVOKO 1.015, but it still can't boot in to see anything on cell. So as of today, I got my computer to recognize the phone and I can actually see the files on my phone and sd card inside. How can I boot into this puppy? I have tried within ABS and the command function to view adb devices, but it does not show up? I get an error : device 0123456789ABCDEF Unauthorized. In my device manager it shows up as ACER phone , and under the Ports section it does show Mediatek Preloader USB VCOM driver (COM 5). I hope I have given enough information to start diagnosing the problem.
Any suggestions how to go about this problem from here?
breezin123