Can some one give me solution/advice/or... about this problem?
Turn off is always take more time for completly turned off from usual when using miui rom.
When my device is fully turn off, i can't turn on (press power button 10second+, my battery level isn't less more 5%, disconected from charger),but, if my device connected to charger, it will show battery level and i can turn on my device.
I'm never (rare) turn off my device, but sometime restart if necessary, never let my device turned off coz 0% battery level, recenly i have a lot clean install, but this problem still present.
Device : Kenzo
Rom : RR 20171217
Firmware : miui_HMNote3ProGlobal_7.12.28_Firmware(emmc_appsboot.mbn included)
Kernel : Radon 6.0
Custom recovery : redwolf, before twrp zcx
Thx for reply.
Related
Hi
I just flashed UI-One MIUI 4.0 PORT [BETA 1] by TEAM MAC (http://forum.xda-developers.com/showthread.php?t=1517939) and the new baseband yesterday night and the phone was working fine. But when i went to sleep the phone had about 25% charge so in the morning it was switched off. Here's what i've done
-I have charged my phone for an hour now via usb/ac adapter and tried removing the battery , sdcard and putting it back in ( some post said to try it) but still the phone doesnt switch on.
- All it shows is the battery indicator when switched off (the really big one being charged) and about 50% is done.
-That screen comes on even if i press and hold power button
-Not able to go into recovery
Anyone any ideas????
rishi_storm said:
Hi
I just flashed UI-One MIUI 4.0 PORT [BETA 1] by TEAM MAC (http://forum.xda-developers.com/showthread.php?t=1517939) and the new baseband yesterday night and the phone was working fine. But when i went to sleep the phone had about 25% charge so in the morning it was switched off. Here's what i've done
-I have charged my phone for an hour now via usb/ac adapter and tried removing the battery , sdcard and putting it back in ( some post said to try it) but still the phone doesnt switch on.
- All it shows is the battery indicator when switched off (the really big one being charged) and about 50% is done.
-That screen comes on even if i press and hold power button
-Not able to go into recovery
Anyone any ideas????
Click to expand...
Click to collapse
well battery drain has been the biggest issue in miui rom as it doesnt get into sleep mode so the soultion just put ur phone in charging for some time on plug socket not via pc .
now use adb to boot into recovery using command or just press the 3 button combo home+vol down+ power and check if it loads into recovery if not than adb is best method to boot into recovery ,
your bootloader is corrupted.. if you can somehow made it to emergyency mode then the situation is undercontrol.. if u can't then take your fone to cc
Sent from my LG-P500 using xda premium
SOLVED
Thanks for the replies guys. You were right. I manual forced emergency mode . Now repairing.
Hi i just installed bad bass battery and noticed that "Kernel" is using 29% of the battery..is that normal?i'm using LF2 stock ROM with siyah 1.1 kernel my battery went from 99% to 94% in 1h15 mn i only have wifi on, no syncing or naything else
It seems to be the kernel your problem,flash another kernel, first try to calibrate your battery ....METHOD 1-- 1
. Please download the phone completely.
2. Try to restart, if this were to happen, do it again to turn off for lack of battery.
3. Loaded the phone off preferably overnight or long.
4. Turn on the phone with the charger plugged in and then pull it off.
N. B. does not require the Root. -METHOD 2-- 1
. Download the phone completely.
2. Enter into Recovery Mode (if it is not possible for lack of battery, connect the phone to the charger).
3. Follow the path Advanced -> Wipe battery stats and confirm.
4. Go back and restart (i.e. , follow the path Go Back -> Reboot system now). 5. Leave charge the phone completely up to 100% (preferably overnight or long) and then let it drain completely until the off., without connecting it to your PC or to the charger, during this period. N. B. You must have Root * Clockworkmod recovery installed. METHOD 3-- 1. Charge your phone to 100% (with the phone turned on) preferably overnight or at least a long period. 2. Leave the phone connected to the charger and switch off the appliance. 3. Let it load still for 10-15 minutes (always without disconnecting it from the charger) in practice you have to see the written full charge or the % to 100 %. 4. Enter into Recovery Mode (always without disconnecting it from the charger) and follow the path Advanced -> Wipe battery stats and confirm. 5. Reboot (i.e. , follow the path Go Back -> Reboot system now). 6. Wait for the entire system is loaded, and then disconnect it from the charger. N. B. You must have Root * Clockworkmod recovery installed. METHOD 5-- 1
. Turn off your phone.
2. Fully charge your phone, preferably overnight or long.
3. When the battery is fully charged and marks the 100% disconnect your phone and remove the battery.
4. Wait for 90 seconds to be exact (it must really be precise, wait exactly 90 seconds.) 6. Put the battery and turn on your phone. N. B. are not required nor Root nor Clockworkmod recovery.
devid801 said:
It seems to be the kernel your problem,flash another kernel, first try to calibrate your battery ....METHOD 1-- 1
. Please download the phone completely.
2. Try to restart, if this were to happen, do it again to turn off for lack of battery.
3. Loaded the phone off preferably overnight or long.
4. Turn on the phone with the charger plugged in and then pull it off.
N. B. does not require the Root. -METHOD 2-- 1
. Download the phone completely.
2. Enter into Recovery Mode (if it is not possible for lack of battery, connect the phone to the charger).
3. Follow the path Advanced -> Wipe battery stats and confirm.
4. Go back and restart (i.e. , follow the path Go Back -> Reboot system now). 5. Leave charge the phone completely up to 100% (preferably overnight or long) and then let it drain completely until the off., without connecting it to your PC or to the charger, during this period. N. B. You must have Root * Clockworkmod recovery installed. METHOD 3-- 1. Charge your phone to 100% (with the phone turned on) preferably overnight or at least a long period. 2. Leave the phone connected to the charger and switch off the appliance. 3. Let it load still for 10-15 minutes (always without disconnecting it from the charger) in practice you have to see the written full charge or the % to 100 %. 4. Enter into Recovery Mode (always without disconnecting it from the charger) and follow the path Advanced -> Wipe battery stats and confirm. 5. Reboot (i.e. , follow the path Go Back -> Reboot system now). 6. Wait for the entire system is loaded, and then disconnect it from the charger. N. B. You must have Root * Clockworkmod recovery installed. METHOD 5-- 1
. Turn off your phone.
2. Fully charge your phone, preferably overnight or long.
3. When the battery is fully charged and marks the 100% disconnect your phone and remove the battery.
4. Wait for 90 seconds to be exact (it must really be precise, wait exactly 90 seconds.) 6. Put the battery and turn on your phone. N. B. are not required nor Root nor Clockworkmod recovery.
Click to expand...
Click to collapse
thnx i will try that..but i do always charge my phone overnight
Battery stats are wiped anyway when the phone is full, they are not used for calibration. (The battery got an internal chip for that)
Calibration is achieved by fully charging, fully discharging in one go and then fully charging again (A so-called battery cycle) as included in the above description.
However note that a full discharge causes a lot of strain to your battery; if you often completely drain your battery it will degrade very fast.
If you got a lot of apps which have data usage or a poor Wifi connection the drain might be normal since it requires the chipset to work far more than under optimal conditions.
ok back again the kernel is eating 37% of the battery as least thats according to bad ass battery stats..i(m on shiyah
Hello Members,
I am having Micromax Knight A350 this phone not having removable battery option because of unibodey design you can remove only two sim cards Like iPhone.
I know in Boot Loop problems best way is to remove battery and then go to recovery wipe the phone and then all is well (this i know from experience of my Old phone Samsung galaxy SL - GT-i9003 )
But know i am having Knight A350 where i can't remove battery
and also I am text you that these following things i all ready tried so don't suggest in Thread
During boot loop
1) press power key only
==> this make phone restart but cant make you out from boot loop. (NOT USEFUL)
2) press power key + volume up key go to recovery and then wipe the phone.
==> i tried this 20 to 30 times but this do nothing worked same as like i pressed only power key.
3) press power key + vol down key then connect with PC and load working ROM.
==> I tried this also but result is same as above
NOTE :- 2nd and 3rd works only when phone is switched off we can say processor in deep sleep and just waiting for interrupt to start(correct me if I text wrong here). but in case of boot loop or restarting we can't put our phone in deep sleep so we cant enable option 2 and 3.
These only steps i tried so please suggest me some Good steps for this fix this issue.
Thanks
bebhav said:
Hello Members,
I am having Micromax Knight A350 this phone not having removable battery option because of unibodey design you can remove only two sim cards Like iPhone.
I know in Boot Loop problems best way is to remove battery and then go to recovery wipe the phone and then all is well (this i know from experience of my Old phone Samsung galaxy SL - GT-i9003 )
But know i am having Knight A350 where i can't remove battery
and also I am text you that these following things i all ready tried so don't suggest in Thread
During boot loop
1) press power key only
==> this make phone restart but cant make you out from boot loop. (NOT USEFUL)
2) press power key + volume up key go to recovery and then wipe the phone.
==> i tried this 20 to 30 times but this do nothing worked same as like i pressed only power key.
3) press power key + vol down key then connect with PC and load working ROM.
==> I tried this also but result is same as above
NOTE :- 2nd and 3rd works only when phone is switched off we can say processor in deep sleep and just waiting for interrupt to start(correct me if I text wrong here). but in case of boot loop or restarting we can't put our phone in deep sleep so we cant enable option 2 and 3.
These only steps i tried so please suggest me some Good steps for this fix this issue.
Thanks
Click to expand...
Click to collapse
Have you tried holding vol+, Vol- and power button all three at a time or wait for the battery to soak up and connect to pc load a working rom using flashtools. i also faced same problems with knight but these worked for me.
I was tried with battery draining
mkarthik241 said:
Have you tried holding vol+, Vol- and power button all three at a time or wait for the battery to soak up and connect to pc load a working rom using flashtools. i also faced same problems with knight but these worked for me.
Click to expand...
Click to collapse
Hi dear,
i tried by battery draining and in my case my battery was at more than 90% , my phone taken 3 heavy days to discharged. after that i found my phone battery in deep discharge state (i am guessing this ) because after attaching my charger , i had wait for 5-10 min for viewind charging display. but nothing come, so i left my phone with charger connected and when i viewed it after 2 hours again then i found it at battery level of 30% around and then work done
thanks
SOLVED : I managed to charge the battery enough in the stock recovery (several hours and using buttons so it doesnt turn off by itself), then proceeded to boot twrp to charge more and fix everything.
ORIGINAL POST :
Hi everyone, I have an issue preventing me from making a tablet work.
Let me guide you through what I have done and can do :
- Acer Iconia Tab 10 (A3-A40) runnig Android 6.0
Problem :
I cannot boot TWRL through fastboot (fastboot boot recovery.img) because it gives me an error (low power - need battery charging). But there is no other way to get the tablet back .
Plus, I cannot charge it while pwered off as I get the following message (along with a battery charging icon) :
Orange State - Your device has been unlocked and can't be trusted - Your device will boot in 5 seconds .
This prevents off-mode-charging as it boots up the tablets after 5 seconds.
How did that happen :
Unlocked the bootloader, booted the tablet, had to use Magisk 13.0 modified by someone to work on the tablet (SU doesn't work.) and set the tablet up.
I then had a popup for Magisk having an update (to 16.0). Accepted it, which resulted in a bootloop.
Wanted to reflash the stock ROM and root it again, but it was 4am and people were sleeping, so I decided to do it the next day. Unfortunately, the battery died while I was asleep.
I can't run some commands in fastboot because it gives me an error : (not support on security).
What I have tried :
Charging the tablet in the (stock) recovery.
Charging the tavlet in Fastboot mode.
Charging the tablet while letting it bootloop.
fastboot getvar all doesnt give me any battery info.
I have all the files I need to make the tablet work (Stock ROM, root files, TWRP file...). I just can't get to flash anything, and the battery doesn't charge.
I just need either :
- A way to remove Magisk from stock recovery
- A way to bypass the fastboot (low power - need battery charging) error
- A way to charge the battery
- Or any suggestion you have
The fact that there is next to nothing about the tablet on the internet is very unfortunate and makes it harder to troubleshoot.
Thanks in advance for your help.
Did you try charging from a wall outlet, while the device is powered off?
HippoInWindow said:
Did you try charging from a wall outlet, while the device is powered off?
Click to expand...
Click to collapse
Yes. But everytime I do that, the device has a message stating "Orange State - Your device has been unlocked and cannot be trusted. Your device will boot up in 5 second".
I believe this prevents off-mode-charging by forcing booting up my tablet.
Strangly enough, fastboot tells me off-mode-charging is on, as of the following :
fastboot getvar all
(bootloader) off-mode-charging 1
FrWhyMe said:
Yes. But everytime I do that, the device has message stating "Orane State - Your device has been unlocked and cannot be trusted. Your device will boot up in 5 second".
I believe this prevenrts off-mode-charging by forcing booting up my tablet.
Strangly enough, fastboot tells me off-mode-charging is on, as when I do :
fastboot getvar all
(bootloader) off-mode-charging 1
Click to expand...
Click to collapse
Try charging if the phone automatically turns on, keep charging, then hold down the power button until it shuts down.
If it still reboots, try adb reboot bootloader, then choose power off. That should do the trick.
HippoInWindow said:
Try charging if the phone automatically turns on, keep charging, then hold down the power button until it shuts down.
If it still reboots, try adb reboot bootloader, then choose power off. That should do the trick.
Click to expand...
Click to collapse
It reboots before I can power it off manually with the power button.
And I cannot access adb as I only have access to the stock recovery and fastboot.
Plus, I can already choose "power off" in the stock recovery, and it stills boots up when plugged in.
SOLVED : I managed to charge the battery enough in the stock recovery (several hours and using buttons so it doesnt turn off by itself), then proceeded to boot twrp to charge more and fix everything.
Hello friends, I come to report here a problem I'm having with my device.
It is not charging my battery, I thought it was a problem in the battery itself, I made the replacement for an original, but the problem was not solved. the device uses all the battery power, it stays at 0% and it does not charge, besides, it recognizes my SIM card, but there is no signal from the operator to make calls or use the 4G network, I did a lot of research I saw that it was a problem related to Software, regarding the CQA test, I saw several tutorials, where none succeeded, lastly, I would like to install a custom rom to see if the problem would be solved, but I went to do the bootloader unlock process, but when Fastboot displays the code and I enter the site of the motorola, it returns me with an error that I can not unlock the bootloader of my cell phone, and I need to unlock to be able to customize the android.
follows a video showing what is happening with my device.
https://www.youtube.com/watch?v=17roum_XlzQ
sorry if my text contains errors, I'm from Brazil and I used the translator to write
Thank you if anyone can help me because I have the device stopped because of this.
Thank you!
Hi, had the same issue. What helped me was connecting
power cable, going to bootloader, from there navigate to recovery. When it boots to recovery, regardless if there is any, leave it for some time. After about 5-10 minutes try rebooting, and it might picked up some charge, then it should charge as normally but very slowly, cellular connection also appeared.
Last time when my phone went to 0% and after going through this procedure my phone was at 17% after charging in recovery mode but didn't charge in normal mode after reboot. I also needed to toggle some setting regarding CQA in bootloader menu. Then everything went back to normal.
I will do this procedure to see if it solves my problem, remembering that my battery is in 0% and with it connected in the device it is only displaying the lightning, informing that the battery is without load.
what settings did you make regarding the CQA?
vNo said:
Hi, had the same issue. What helped me was connecting
power cable, going to bootloader, from there navigate to recovery. When it boots to recovery, regardless if there is any, leave it for some time. After about 5-10 minutes try rebooting, and it might picked up some charge, then it should charge as normally but very slowly, cellular connection also appeared.
Last time when my phone went to 0% and after going through this procedure my phone was at 17% after charging in recovery mode but didn't charge in normal mode after reboot. I also needed to toggle some setting regarding CQA in bootloader menu. Then everything went back to normal.
Click to expand...
Click to collapse
My device does not hold 5 seconds on bootloader because my battery is at 0% I believe the power supplied by the cable in the charger is not enough to keep it powered on. and now?
Original charger is definitely more than enough to keep phone on in bootloader mode. Try to make sure that usb C connection is dust and grease free.
Regarding CQA mode setting I can't remember exactly, but that is second thing.
Maybe even 5 seconds in bootloader should be just fine to navigate to recovery.
I wish you good luck, i was almost desperate when it firstly happened to me.
i had the same problem. after lot of trial and error i found a solution.
connect to power source (wall adaptor/modo battery mod.) get into bootloader menu and wait for 5 mins pressing vol up or down frequently.
then select reboot to recovery. on red triangle screen holding power button press and release volume up button one time. you will get into android stock recovery
select option wipe cache partition. and select yes when asked.
keep charging the device upto half hour in recovery mode and then select option reboot to bootloader.
after bootloader menu appears scroll down to BPTools and select it.
Your Phone will reboot and you will get Network and Your Phone will also charge normally.
Warning: Do not let your phone discharge to 0% or you might have to perform all above steps again.
This method worked for me as well. I recently replaced the battery on my Moto z force droid but couldn't get it to charge and signal was gone, after trying several things the Bp tools worked great, thanks dude.