Related
First off, I must apologize and say. Yes, I know there are all ready two other posts just this week on 'Did I kill my phone, Is it dead etc.'
So, to make a long story short.
After much research, I started at the ppcgeeks.com forums, then ppckitchen.org and finally made my way over here. I decided it was time to start working on updating my phone.
First off; I downloaded the wrong link and flashed the Olipro 1.20 boot loader on the phone, instead of the 2.4x version that is being used now. No big deal, I then got into boot loader mode and went to flash a stock rom to fix the issue. The rom had an error in the middle and reset. Then my phone reset. It went back into boot loader mode and then after using titan_exitbl.exe it booted to the standard HTC screen. After a moment now at this screen it will display the HTC logo and No Radio in red. After much reading I found that I could simply flash my 512mb MicroSD card, and did. And I placed the TITAIMG.nbh file on the root. (that is the only thing on the card) to upgrade the radio. But now when I try to restart into boot loader mode (power, camera, reset) it only resets and does not go into boot loader mode. I can perform a hard reset and go through the prompts there, but after it completes it simply brings me back to the HTC logo, and No Radio.
There is no connection via Active sync, nor through the USB, so I can not use mtty to edit anything on the boot loader end.
I have done quite a bit of reading and I figure this probably has been asked before, but is there a way to get my phone to get back to boot loader mode so I can load at least a stock rom onto it?
I don't know a whole lot about troubleshooting phones considering I have only had mine for a few weeks. However I have worked for Geek Squad for 3 years so troubleshooting is kind of in my nature.
Have you tried putting it in bootloader mode without your SD card in there? If there is something wrong with the .nbh you have on it and it keeps trying to load it when in bootloader, that could be your problem. I would remove the SD card and try bootloader, at which point you should be able to flash via usb.
Worth a shot at least.
Flash a new bootloader like 2.47 via sd. Then start loading radio and rom from there.
flipzmode said:
I don't know a whole lot about troubleshooting phones considering I have only had mine for a few weeks. However I have worked for Geek Squad for 3 years so troubleshooting is kind of in my nature.
Have you tried putting it in bootloader mode without your SD card in there? If there is something wrong with the .nbh you have on it and it keeps trying to load it when in bootloader, that could be your problem. I would remove the SD card and try bootloader, at which point you should be able to flash via usb.
Worth a shot at least.
Click to expand...
Click to collapse
Yes I have tried with and without the SD card in the phone. I have also tried with and without the phone connected to a USB cable.
I cannot flash anything to the phone because i cannot establish a connection to the phone via ActiveSync.
Did you try what I suggested? Can you get to just the bootloader screen? Hold power and camera then push reset at same time for bootloader.
drewcam888 said:
Did you try what I suggested? Can you get to just the bootloader screen? Hold power and camera then push reset at same time for bootloader.
Click to expand...
Click to collapse
That is the problem. I have tried that. power, camera, and reset. And any combination of other button, SD card in/out, USB in/out, and anything else i can think of...
The bootloader screen will Not come up.
What can the phone do? Kinda sounds like it might be bricked.
drewcam888 said:
What can the phone do? Kinda sounds like it might be bricked.
Click to expand...
Click to collapse
I know, I hope it is not. This is my phone for work, and my boss is pretty pissed that I might have just bricked a phone he just paid for.
It will turn on from the power button, i can reset it normally with the reset push switch. (it then returns to the HTC logo, and No Radio in red). I can also do the 'bootloader' reset, but this does not bring it to the bootloader, it simply acts as a standard reset. I can also do a 'hard' reset, both of the select keys, and the reset switch. It will then boot into the 'do you want to hard reset your phone' prompt, and it will let me go through those steps that would normally hard reset the phone. After the reboot when that is finished it again goes to the HTC logo and No Radio. So, with that, I sure hope that some part of the bootloader is in tack.
Thank you for your help so far.
Are you sure you are holding both the camera and power button at the same time and then pushing reset button while still holding?
psycopyro182 said:
Yes I have tried with and without the SD card in the phone. I have also tried with and without the phone connected to a USB cable.
I cannot flash anything to the phone because i cannot establish a connection to the phone via ActiveSync.
Click to expand...
Click to collapse
From what it sounds like, you're trying to run the bootloader with and without the SD card in. The problem is, it sounds like you don't have a working file actually on the SD card. It also seems that since you cannot make an ActiveSync connection, you aren't able to transfer files to and from the card.
Do you have a microSD card reader?
Check this out: http://wiki.xda-developers.com/index.php?pagename=TitanRecentHome
Particularly Section II.2.A. That may fix your problem.
Hope this helps!
Oh and if it doesn't something you said about your boss having 'just' paid for your phone. If its new enough... w-a-r-r-a-n-t-y!
He can't follow those suggestions on the wiki exactly because he cant get a usb connection. But I agree he needs to load the 2.47 on his card using a adapter then try bootloader again.
Did you try EnterBL.exe?
DustinEarnhardt said:
From what it sounds like, you're trying to run the bootloader with and without the SD card in.
Oh and if it doesn't something you said about your boss having 'just' paid for your phone. If its new enough... w-a-r-r-a-n-t-y!
Click to expand...
Click to collapse
I cannot even get the bootloader to come up. Yes I know that I am pressing both buttons and hitting Reset.
And as for Warranty, Will they warranty a phone that has the updated bootloader on it? I know there is a utility to Re-flash your phone to stock, but well, i cant even get mine to do anything at this point. I dont want sprint to tell me that they will not warranty it because I have 'tampered' with it, or 'voided the warranty'.
bitserve said:
Did you try EnterBL.exe?
Click to expand...
Click to collapse
I did not know there was such a tool.
A direct link would be great. That sound like what i need to get out of this mess.
Heres the deal, if you can't get it to go to bootloader, the carrier probably can't either....
I think the enter_BL only works if active sync works, but I could be wrong.
I've never seen a phone yet, or heard of one for that matter that boots as far as yours does yet doesn't go to a bootloader screen when reset properly. It does sound pretty messed up.
More than likely, if you go into the store and say "Hey this is messed up because I tried to update the bootloader on it" you'll get some pretty quizzical looks. They'll more than likely take your phone in the back, not do a thing with it, and then issue you a replacement (if they have one in stock) or mail you one as soon as possible.
It does sound like you may have created a brick, but luckily this one is replaceable. Consider it a "lesson learned" for the next one.
(My apologies if I offend any VZW store employees. I sure there is a rare breed of highly competent and capable technicians out there, but I have yet to meet one in my area.)
Boots Up?
Does your phone boot all the way up where you can explore your SD card on your phone? If you can PM me and I may have a solution for you if your bootloader allows you to flash by SD card.
Brick = New Phone
DustinEarnhardt said:
More than likely, if you go into the store and say "Hey this is messed up because I tried to update the bootloader on it" you'll get some pretty quizzical looks. They'll more than likely take your phone in the back, not do a thing with it, and then issue you a replacement (if they have one in stock) or mail you one as soon as possible.
It does sound like you may have created a brick, but luckily this one is replaceable. Consider it a "lesson learned" for the next one.
one in my area.)
Click to expand...
Click to collapse
So, I walked into the store, and simply said. "I have insurance, what do I need to tell you in order to get the phone fixed." "what do you mean?" "Well i have my phone here, it is totally bricked, the bootloader is toast, and there is no radio or rom, and it will not connect to activesync. So, if i need to come back and tell you my phone is stolen i can."
"Um ok? bricked? bootloader?... Here, let me see it"
(Lucky for me my company had just purchased about a dozen phones from this store, and the techs were happy to work with me)
The tech took the phone in back, and he and another tech looked at it, tried to hard reset, tried the enter bootloader key press. tried to plug it in. Then they both scratched their heads with a completly dumbfounded look on their faces. One of them walked to the closet, grabbed a new phone and brought it to me and said. "Congrats, this is the most screwed up phone I have seen come in here. Here is a brand new one, We will have to send this one back to corporate."
So, now shiny new phone in hand.
I can say simply "Lesson Learned"
Thanks for all of your help guys.
Well, I have a d2pad SN 201301 on the back so its somewhat new
It uses rk2829 rockchip.
Anyways Ive been trying to get recovery on it for the past couple hours to use a new rom, finally got recovery working, did everything installed my rom, and let it restart.
Well, The rom isnt compatible, there was a later version a few pages into the thread that might have been, but the one I got wasnt.
So now I'm stuck, at the intro d2 logo
I only have 1 button and it is power.
Ive tried to get adb working, because it at least says its connected, but with no success anyone have any ideas?
wzzupp548 said:
Well, I have a d2pad SN 201301 on the back so its somewhat new
It uses rk2829 rockchip.
Anyways Ive been trying to get recovery on it for the past couple hours to use a new rom, finally got recovery working, did everything installed my rom, and let it restart.
Well, The rom isnt compatible, there was a later version a few pages into the thread that might have been, but the one I got wasnt.
So now I'm stuck, at the intro d2 logo
I only have 1 button and it is power.
Ive tried to get adb working, because it at least says its connected, but with no success anyone have any ideas?
Click to expand...
Click to collapse
Hey, I realize that it's been a couple years since you posted this question. I never saw any responses. So how did it all end?
Also, there was one critical piece of information you failed to share with the XDA community...you said you worked on getting into recovery with a device that only had a power button and no volume buttons. May I ask how on earth you managed to get into recovery using only a power button? Reason I ask is that I am now facing this situation. NTech Alexis RX3HD8 tablet, rockchip RK2928 processor, power button and no volume buttons! I need to get into recovery but I cannot turn on USB debugging (and the tablet is pattern locked but the pattern was entered too many times....so I am locked out).
At this point, if I cannot enter recovery mode, the tablet is a permanently soft-bricked which is, for all intents and purposes, the same as a hard-brick.
I think what happened for me was, wanted to install new rom, got into recovery to install it, then it bricked my tab, after that I was at the logo
in my case i fixed everything by getting a rkflasher, to reinstall it, and contacting support for the factory image, which is lucky they new something about it, some companies abandon support, or dont know enoguh about what they sell, lol
as for your situation
these are the things i'd try
1. If it has google play, and is connected wifi even if its locked you can try this page
https://www.google.com/android/devicemanager
and then pick ur device and factory reset it is an option (although ive never tried it)
2. search around on the internet for 1 button recovery methods, I've seen quite a few weird tablets, and some I can think of with 1 button recovery
A. a pin hole thats not the reset button or the mic, was an actual button, and that was used to get into recovery with a safety pin, and doing the normal holding it while powering on method
B.. holding the power button, and instead of letting go when u see a logo, keep holding it, till it shuts off again, then power it on
C. plug it in to pc via usb, and turn it on, while its booting, see if ur pc recognizes it at any point during the startup and try to run some commands, ive had a brand of tabs, that give u adb access during boot, but then remove it after finished booting
4. their website is in spanish, and they dont have firmware/manual links available for your tablet
You could contact support for recovery instructions or reflash instructions,, and hope they speak english or you speak Spanish
Most of the time with 1 button tablets, if theirs no info of similar ones online, unless you can contact support, you might be out of luck
PS, my edit:
also, I saw ur post on the youtube video while looking up stuff about this tablet, if that guy can get you a firmware, you have another option of trying to get to download mode too
my tablet, with rk2928 uses these instructions to get it to show up in the RKBatchTool.
https://www.d2pad.info/docs/OSFirmwareInstallInstruction_D2-721.pdf
maybe they can help you get into download mode on urs
all of this being said, I hope my first suggestion will work, IDK if wifi is disabled during pattern lock, or if u can factory reset any tablet, I just know I always see that option when I'm using it to find my devices ect.
CVAngelo said:
Hey, I realize that it's been a couple years since you posted this question. I never saw any responses. So how did it all end?
Also, there was one critical piece of information you failed to share with the XDA community...you said you worked on getting into recovery with a device that only had a power button and no volume buttons. May I ask how on earth you managed to get into recovery using only a power button? Reason I ask is that I am now facing this situation. NTech Alexis RX3HD8 tablet, rockchip RK2928 processor, power button and no volume buttons! I need to get into recovery but I cannot turn on USB debugging (and the tablet is pattern locked but the pattern was entered too many times....so I am locked out).
At this point, if I cannot enter recovery mode, the tablet is a permanently soft-bricked which is, for all intents and purposes, the same as a hard-brick.
Click to expand...
Click to collapse
Without ADB a soft-brick can become permanent state!
wzzupp548 said:
I think what happened for me was, wanted to install new rom, got into recovery to install it, then it bricked my tab, after that I was at the logo
in my case i fixed everything by getting a rkflasher, to reinstall it, and contacting support for the factory image, which is lucky they new something about it, some companies abandon support, or dont know enoguh about what they sell, lol
as for your situation
these are the things i'd try
1. If it has google play, and is connected wifi even if its locked you can try this page
https://www.google.com/android/devicemanager
and then pick ur device and factory reset it is an option (although ive never tried it)
2. search around on the internet for 1 button recovery methods, I've seen quite a few weird tablets, and some I can think of with 1 button recovery
A. a pin hole thats not the reset button or the mic, was an actual button, and that was used to get into recovery with a safety pin, and doing the normal holding it while powering on method
B.. holding the power button, and instead of letting go when u see a logo, keep holding it, till it shuts off again, then power it on
C. plug it in to pc via usb, and turn it on, while its booting, see if ur pc recognizes it at any point during the startup and try to run some commands, ive had a brand of tabs, that give u adb access during boot, but then remove it after finished booting
4. their website is in spanish, and they dont have firmware/manual links available for your tablet
You could contact support for recovery instructions or reflash instructions,, and hope they speak english or you speak Spanish
Most of the time with 1 button tablets, if theirs no info of similar ones online, unless you can contact support, you might be out of luck
PS, my edit:
also, I saw ur post on the youtube video while looking up stuff about this tablet, if that guy can get you a firmware, you have another option of trying to get to download mode too
my tablet, with rk2928 uses these instructions to get it to show up in the RKBatchTool.
https://www.d2pad.info/docs/OSFirmwareInstallInstruction_D2-721.pdf
maybe they can help you get into download mode on urs
all of this being said, I hope my first suggestion will work, IDK if wifi is disabled during pattern lock, or if u can factory reset any tablet, I just know I always see that option when I'm using it to find my devices ect.
Click to expand...
Click to collapse
Hey thanks for getting back to me. You've been extremely helpful and your response may hopefully be found in future by others who have the same problem.
Here's how it's working out for me with this device:
1. It has Google Play but unfortunately the wifi is turned off and there's no way to connect. But in any event, the little kid whose tablet it is (I'm working on the tablet at the request of her father who is my friend), she doesn't remember the Gmail account name or password.
2. I've searched the entire Internet (LOL) including Spanish and Chinese websites/videos but no luck. I can't find anything about putting this badboy into recovery. The reset button is just for show...it only turns the tablet off in case the power button is unresponsive.
3. I've been to the website of "manufacturer". It's a Portuguese company (I speak the language) but they haven't responded to any contact requests. And they appear to offer the firmware for the devices but download link is dead. So I cannot even get the firmware to flash it. The dude on YouTube has not sent me any link to firmware.
But the bigger problem and the key to the issue is that I cannot get the tablet to be recognized by the computer no matter what I've tried. I've tried all kinds of combinations of power button play but I never get that satisfying BEEP that indicates that there is a connection open. You see, I have the drivers for the tablet but there is no way to install them without the tablet giving the opening (even if it would come back as Unknown Device). So, I'm crap out of luck with this soft-brick.
Again, thanks for your help. After 3 days and probably 15 hours spent trying to reset this thing, I'm going to have to throw in the towel. Important lessons learned:
#1. NEVER PURCHASE AN ANDROID DEVICE THAT HAS NO VOLUME KEYS (or without knowing how to get into recovery). You're only asking for trouble if anything should go wrong. And believe me, this is the THIRD TIME I've seen a device that cannot go into recovery. In one case, I was able to flash new firmware directly on bootup off the external SD card (it was an Android laptop with WM8505 chip). I guess one out of three ain't bad odds...but they are not the kind of odds you want with expensive devices.
#2. ALWAYS TURN ON USB DEBUGGING WITH ANY ANDROID DEVICE YOU OWN AND TELL YOUR FRIENDS TO DO THE SAME. One day, it may end up being the savior of the life of that device because it usually means you can access the device via ADB in case of a soft-brick. LOL.
CVAngelo said:
Hey thanks for getting back to me. You've been extremely helpful and your response may hopefully be found in future by others who have the same problem.
Here's how it's working out for me with this device:
1. It has Google Play but unfortunately the wifi is turned off and there's no way to connect. But in any event, the little kid whose tablet it is (I'm working on the tablet at the request of her father who is my friend), she doesn't remember the Gmail account name or password.
2. I've searched the entire Internet (LOL) including Spanish and Chinese websites/videos but no luck. I can't find anything about putting this badboy into recovery. The reset button is just for show...it only turns the tablet off in case the power button is unresponsive.
3. I've been to the website of "manufacturer". It's a Portuguese company (I speak the language) but they haven't responded to any contact requests. And they appear to offer the firmware for the devices but download link is dead. So I cannot even get the firmware to flash it. The dude on YouTube has not sent me any link to firmware.
But the bigger problem and the key to the issue is that I cannot get the tablet to be recognized by the computer no matter what I've tried. I've tried all kinds of combinations of power button play but I never get that satisfying BEEP that indicates that there is a connection open. You see, I have the drivers for the tablet but there is no way to install them without the tablet giving the opening (even if it would come back as Unknown Device). So, I'm crap out of luck with this soft-brick.
Again, thanks for your help. After 3 days and probably 15 hours spent trying to reset this thing, I'm going to have to throw in the towel. Important lessons learned:
#1. NEVER PURCHASE AN ANDROID DEVICE THAT HAS NO VOLUME KEYS (or without knowing how to get into recovery). You're only asking for trouble if anything should go wrong. And believe me, this is the THIRD TIME I've seen a device that cannot go into recovery. In one case, I was able to flash new firmware directly on bootup off the external SD card (it was an Android laptop with WM8505 chip). I guess one out of three ain't bad odds...but they are not the kind of odds you want with expensive devices.
#2. ALWAYS TURN ON USB DEBUGGING WITH ANY ANDROID DEVICE YOU OWN AND TELL YOUR FRIENDS TO DO THE SAME. One day, it may end up being the savior of the life of that device because it usually means you can access the device via ADB in case of a soft-brick. LOL.
Click to expand...
Click to collapse
At last, did we find at last how to enter in recovery mode if there is only one button (power). I am in the same situation with @CVAngelo .Is it possible not to exist recovery mode at all? My tablet is BENEVE R708G with Rockchip RK2928. I tried every combination with power button and reset button but no luck at all.I have boot loop after trying to change the bootanimation.The weird thing is that the new boot animation ''works'' but after that it goes on boot loop forever.
Hi everyone,
I'm sorry if ever I'm posting this on the wrong section cause I'm not sure if this is a problem from android or samsung.
I'm not good at all when it comes to phone troubleshooting so I will try my luck and ask questions about what have happened to my phone just awhile ago. I got this phone from Japan(Samsung Galaxy SII Wimax isw11sc) months ago and I only use it for multimedia purposes as it is region locked and I am at another country atm. everything is running fine until my phone asked for a software update(not really sure what upgrade that was) and I decided to give it a shot and let it download the updates. I left it to do some chores and when I came back to check on it, it reboot looped itself on the AU(mobile phone company from japan) logo.
I did some research and found some things like hard reset and download mode. I tried to do the hard reset(power/home/volume up) method but I can't seem to access the settings instead, the phone keeps on showing me this "Preparing for S/W update. Please wait." after a few seconds, the phone will reset itself back to the reboot loop.
I tried to do the download mode using odin mode but then, I realized that my phone and computer won' connect via USB port because well, my phone won't boot. Also downloaded the manual driver but my pc won't recognize it.(win7 if that helps.)
Please tell me what have happened and what I can do to fix this problem, I don't really care if i lose everything that I have stored on my phone, I just want it to work again. Help will be much appreciated, Thank you.
Hi, I've been browsing the forums for people's attempts to fix a problem. At first the phone just turned off and I was unable to turn it on because it was stuck in a boot loop. The rom I had running was an ICS stock rom from hk. During this time i was still able to get into download mode but unable to enter recovery. I have tried many times to get to recovery and then tried to flash with several stock roms too. Upon failing around 10 times I moved on to a custom rom.
This one here:
http://forum.xda-developers.com/galaxy-s2/help/guide-26-12-flash-stock-firmware-rom-t2365701
The Jelly bean one here.
Upon failing from this too and unable to do anything but reset the phone and try again. I managed to turn it off... but now unable to turn it on in any way or get into download mode or recovery.
Is there anything I can try to do to get the phone to be working? What can I do?
Try a jig but understand it's very unlikely to get you into download mode. Service centre or local mobile repair shop for diagnosis (I also doubt it will be JTAG'able).
Edit - Also, search for KingRat's 'jump start' method where you try & boot the phone with just the charger/without the battery.
medow70 said:
Hi, I've been browsing the forums for people's attempts to fix a problem. At first the phone just turned off and I was unable to turn it on because it was stuck in a boot loop. The rom I had running was an ICS stock rom from hk. During this time i was still able to get into download mode but unable to enter recovery. I have tried many times to get to recovery and then tried to flash with several stock roms too. Upon failing around 10 times I moved on to a custom rom.
This one here:
http://forum.xda-developers.com/galaxy-s2/help/guide-26-12-flash-stock-firmware-rom-t2365701
The Jelly bean one here.
Upon failing from this too and unable to do anything but reset the phone and try again. I managed to turn it off... but now unable to turn it on in any way or get into download mode or recovery.
Is there anything I can try to do to get the phone to be working? What can I do?
Click to expand...
Click to collapse
Don't loose hope mate...
Try remove battery and insert charger (optional)...
Press voldown+home+power button then let someone (your mother, father, brother, sister, neighbor or friends) insert the battery for you while still pressing those 3 keys...
I hope it will enter to download mode again...and report back please...
Try to use an other battery, my original one is fuked up, it does nothing.
I bought a new one and it works
I tried plugging my charger to the phone and pressing the 3 buttons and then having someone plug the battery in for me, still wouldn't start up. Also tried it with another battery i have on hand, also no luck.
You know what the options are then. Ignore people making ridiculous suggestions which don't work. My aim is to be honest with people, tell them the truth, and have them either get their phones fixed or replaced as quickly as possible in this situation (let's face it, nobody likes to be without a phone), rather than fill them with false hope & waste their time.
I think I fried my mobo while trying to flash it cause it does head up the phone without showing anything. I am going to order parts on ebay. I got this confirmed by someone at a shop near where I live, however they won't replace the mobo for me even if i do find a working one.
=) luckily this isn't my phone but my dad's who works at home and doesn't mind using an OLD OLD flip phone just for calls for the time being.
Side question, even if i replace the mobo and I get it booted but I still get stuck in the boot screen loop and unable to flash to any stock roms what can I do?
If you replace the motherboard you should fix it without further problems. New motherboard = new NAND, no more bootloop - unless you flash again & the flash is bad; you can't mitigate the risk of a bad flash, you can only do all the sensible things like making sure you're using a PC with reliable USB ports, that you're flashing the correct firmware for your device, that you're using an original Samsung USB cable. Basically, if you're careful, the risk with any given flash is very low.
So, fix the hardware problem, flash stock for your country/carrier once you've done that, and go from there.
:crying: So... I am a young teenage boy, who got an android, Samsung galaxy S3 Mini for my birthday, and I have had it for a year, I used an app to unlock the boot loader, but I was so happy that I turned it off before the operation was done I think, since I turned it off right when it got root access, I feel like I wanna kill myself, for reals...
I told my dad everything, he threw me at the the wall, shook me violently, and he raised his fist at me, I was terrified, and now I am trying to fix it with only a USB and Computer, no SD card since my damn uncle took my best one, my 32GB SD, and I have no JTAG or any modding device...
Please help, NOTHING HAPPENS, when I try to go into the boot loader, recovery mode, or factory mode, and it does not even show a LED light or it won't even buzz...
My friend had it for about a month, and he said once he held the power button for about a half an hour, and he said it quickly buzzed, but then nothing else happened...
I almost do not believe him so far, and I tried plugging it into my computer, it says everything is working fine, it detects it and everything, but I cannot go into the file system and Odin does not detect it... Please help!
Also, if my computer at LEAST detects it,or if it buxzed, can I fix it without a JTAG or SD card?