Respected experts
My Honor holly u19 was stuck in bootloop so I used Philz recovery mode to factory reset my device but after cleaning the cache and Dalvik cache memory I also performed clean for new ROM installation option.
After that my phone restarted and on start screen there were several error coming and only ok option was there. Therefore I thought to install a new ROM. I tried installing the stock ROM but it was unsuccessful I don't know why.
I tried to restore my complete ROM. But there were mounting issues and I am attaching the issue.
Hi Google through net and found solution by formatting the data cache and system.
But after that my phone was stuck at the logo only.
finally I decided to use SP Flash tool and downloaded the drivers and scatter file required but after performing the SP Flash tool download my phone didn't respond at all this completed bed and no animation and charging LED light is off or not working.
Pls pls help
Related
I've search long and hard ..to no avail. I have a huawei ascend d1 qaud u9510e. Its had a chinese custom recovery and was flashed with MIUI 3.2.22. From the UPdater miui i've been spammed by to do a 'weekly update'' on a daily basis. I read it , it said it didnt delete internal and minimum problem would happen. So I did it. It went through the install phone rebooted. it worked one time till I restarted phone. now i am unable to get back .All i see is the HUAWEI start up logo. it just hangs there. the phone wont turn off just restarts itself to that screen, I am unable to get to custom recovery by holding the power button + volume + which etc. I have the original miui 3.2.22 on my sd card but cannot get to that because of this bootloop/cannot access reovery mode. majority of the time my computer will not reogonize my device but sometimes my computer recognize my phone as adb. How Can I fix it so I can get to a recovery so I can reflash to previous working rom. thank you for your time
T2av said:
I've search long and hard ..to no avail. I have a huawei ascend d1 qaud u9510e. Its had a chinese custom recovery and was flashed with MIUI 3.2.22. From the UPdater miui i've been spammed by to do a 'weekly update'' on a daily basis. I read it , it said it didnt delete internal and minimum problem would happen. So I did it. It went through the install phone rebooted. it worked one time till I restarted phone. now i am unable to get back .All i see is the HUAWEI start up logo. it just hangs there. the phone wont turn off just restarts itself to that screen, I am unable to get to custom recovery by holding the power button + volume + which etc. I have the original miui 3.2.22 on my sd card but cannot get to that because of this bootloop/cannot access reovery mode. majority of the time my computer will not reogonize my device but sometimes my computer recognize my phone as adb. How Can I fix it so I can get to a recovery so I can reflash to previous working rom. thank you for your time
Click to expand...
Click to collapse
you must download U9510E B610 EMUI 2.0 by svikfromorel v02 for XDA search for this in the forum i cant post any link...
unpack, connect the phone to PC and run Flash_all.bat file
after ending a proccess don't forget do wipe data and wipe cache
huawei u9510e bricked
eldukex1 said:
you must download U9510E B610 EMUI 2.0 by svikfromorel v02 for XDA search for this in the forum i cant post any link...
unpack, connect the phone to PC and run Flash_all.bat file
after ending a proccess don't forget do wipe data and wipe cache
Click to expand...
Click to collapse
Hi, I am a newbie to flashing custom Roms. I desperately need help. I have the same phone and the same thing happened to me while trying to flash a ROM. My screen was stuck on huawei logo. Unfortunately, it happened in the middle of the high so by the morning the battery got drained completely. What are my options if any? Please help. I am willing to pay. Thanks a lot in advance.
I have a a Lenovo Yoga 8 B6000. Im running 4.4.2 and after some fiddling, used Vroot to root, and subsequently went through some arduous steps to finally remove the Vroot and replace with SuperSu. Life was good. Then I got a little careless when removing some of the bloatware and ended up with a constant boot-loop problem. And of course, no backup. (whoops!)
I have been researching this the past 2 days for a workable solution and am reaching out for some more refined assistance.
Here is what I have done thus far:
When pressing Power + VOL+/- I get to the initial recovery menu which gave me: Recovery, Fastboot, and Normal. After selecting the "Recovery" mode, I get the "No Command", after which I pressed the power button one more time and got into the English recovery menu. I show
Android System Recovery <3e>
B6000_A442_001_026_141117_WW_WIFI
Reboot System Now
Apply Update from ADB
Apply Update from SDCard
Apply update from Cache
Wipe data/Factory Reset
Wipe Cache Partition
I attempted to wipe the cache, followed by Wipe data/Factory reset. Following this procedure, I remained in the boot loop.
I installed ADB Flashtool drivers for WIN7 and attempted to use flash tool which was also suggested on this site. I got a 4.2.2 ROM "B6000_A422_000_059_131219_WW_WIFI" from a russian lenovo forum site to use with the flash tool and because the tablet continues in boot loop when starting, there was no loading of the ROM from that method.
I put the rom on an SD card and went into recovery mode. The ROM was not visible by the recovery menu (By that I guess the Apply Update from SDCard is looking for a specific file extension, which is not present).
I may have tried a few other things which are not popping into my head at the moment.
Im kind of at a loss and looking for any ideas from the gurus out there on how I might be able to get any kind of ROM to flash onto my B6000 and getting it up and running again.
Thanks
I was able to successfully fix the Yoga 8 tablet by using the instructions here:
//aluk4rd.wordpress.com/2014/09/08/an-easy-guide-for-restoring-your-stock-4-2-2-firmware-on-your-lenovo-yoga-tablets-8-and-10-b6000-and-b8000/
The trickiest part was getting the Mediatek driver installed. I use a dual booting MAC with WIN7 and sometimes there are some kwirks when operating in WIN7. However, the results of the instructions brought my tablet back to life, as well as downgrading to 4.2.2
Hi engineer2loggie,
How did you get that firmware? Can you tell where can I download it?
Thanks.
has anybody found a solution to this? im stuck with the same problem atm
hey guys I need some help :crying::crying:
my phone is cloudfone geo 402q mediatek mt6582
yesterday my phone reacting so weird
after i install team viewer last night, yesterday morning my phone always giving me an error of com.android.process.acore
I have already search answer to fix my answer they say I should wipe the contact storage and contact . Then that's what I did but nothing happens.
I decided to format my phone from (TWRP)recovery and still nothing happened.
TWRP gave me a success output in re-formatting but when I turn ON my phone it wasn't re-formatted by recovery.
I tried to format from factory mode still nothing happens
I tried to re-flash the firmware from spflash tools. It flash the ROM but
when I turn ON my phone still nothing happened
(nothing happened i mean my phone wasn't able to reformat by recovery and flashtool even the factory mode)
I guess the problem is my android phone system mounted as read-only and no tools that cant mount it to format it
please help thanks
I was facing an issue with the phone being stuck in logo screen.I tried to wipe the user data and was unable to do so via recovery.So I flashed the phone with stock rom using Sp Flash tool.Still it once again remained stuck in logo screen.So I tried to format the phone and after that the phone is dead , It does not charge nor power up.I once again tried with format all and download and sp flash tool flashed it successfully and showed the okay screen.The flashing process is happening but the phone does not boot on pressing the power button.It is like totaly dead.Except the only thing that recognizes my phone is the flash tool.Even my laptop which runs on Ubuntu 16.04 does not show any kind of indication on connecting.Please give me a solution.I am very panicked.
How I encountered this problem:
1.Since I was stuck at the boot loop.I tried to wipe data entirely through recovery.There was mount error due to encryption.So my only chance was at flashing the phone.
2.I had 3 version of stock Rom for 3 different build(I didn't know my build no).I tried flashing them all but all the 3 flashed successfully but the result was
same.Stuck at bootloop.I found out this might be because I was unable to wipe the data from phone.
3.So I wiped the entire data using sp flash tool using the format flash except boot loader option.
4.After that I had 3 versions of stock Rom with me for different build no.And I think I flashed the one with
the build no which was not meant for my phone.
5.The flashing was successfull.But the phone was dead.
6.Then once again I reflashed other version during which once the flashing was interrupted.
7.Finally I flashed the correct Stock rom version for my build no.Because It was in the end I found out my build no.
8.The flashing was successfull except the phone is still dead.
Observations:
A.Memory Test:
1.ERROR:NAND FLASH NOT DETECTED.(This was present even before the phone became dead .ie when it was stuck at the boot loop after flashing the firmwares).
2.ERROR:UFS not detected.(This was present even before the phone became dead .ie when it was stuck at the boot loop).
Rest went well.The memory test in the end showed the okay message.
B.Format option:
Now the format option does not work.
When I try to format the phone once again using sp flashtool format whole flash except bootloader.It says ERROR : S_DL_READ_PT_FAIL (5073).
what went well?
I am able to download the preloader first and then seperately download rest of the components.
This I am able to do with and without the battery.
what didnt go well?
1.The phone is still dead.No reaction from the phone on pressing any button.
2.Phone LED does not blink or light up on connecting with or without battery to the wall charger or laptop.
3.The screen is black.
I have a question.
should I try the format whole flash option and not format whole flash except boot loader?
I did not try this since latest version doesnt have this.And there are many people who have encountered problems too with that option.
PLEASE HELP ME.THANK YOU.
pjseven said:
I was facing an issue with the phone being stuck in logo screen.I tried to wipe the user data and was unable to do so via recovery.So I flashed the phone with stock rom using Sp Flash tool.Still it once again remained stuck in logo screen.So I tried to format the phone and after that the phone is dead , It does not charge nor power up.I once again tried with format all and download and sp flash tool flashed it successfully and showed the okay screen.The flashing process is happening but the phone does not boot on pressing the power button.It is like totaly dead.Except the only thing that recognizes my phone is the flash tool.Even my laptop which runs on Ubuntu 16.04 does not show any kind of indication on connecting.Please give me a solution.I am very panicked.
How I encountered this problem:
1.Since I was stuck at the boot loop.I tried to wipe data entirely through recovery.There was mount error due to encryption.So my only chance was at flashing the phone.
2.I had 3 version of stock Rom for 3 different build(I didn't know my build no).I tried flashing them all but all the 3 flashed successfully but the result was
same.Stuck at bootloop.I found out this might be because I was unable to wipe the data from phone.
3.So I wiped the entire data using sp flash tool using the format flash except boot loader option.
4.After that I had 3 versions of stock Rom with me for different build no.And I think I flashed the one with
the build no which was not meant for my phone.
5.The flashing was successfull.But the phone was dead.
6.Then once again I reflashed other version during which once the flashing was interrupted.
7.Finally I flashed the correct Stock rom version for my build no.Because It was in the end I found out my build no.
8.The flashing was successfull except the phone is still dead.
Observations:
A.Memory Test:
1.ERROR:NAND FLASH NOT DETECTED.(This was present even before the phone became dead .ie when it was stuck at the boot loop after flashing the firmwares).
2.ERROR:UFS not detected.(This was present even before the phone became dead .ie when it was stuck at the boot loop).
Rest went well.The memory test in the end showed the okay message.
B.Format option:
Now the format option does not work.
When I try to format the phone once again using sp flashtool format whole flash except bootloader.It says ERROR : S_DL_READ_PT_FAIL (5073).
what went well?
I am able to download the preloader first and then seperately download rest of the components.
This I am able to do with and without the battery.
what didnt go well?
1.The phone is still dead.No reaction from the phone on pressing any button.
2.Phone LED does not blink or light up on connecting with or without battery to the wall charger or laptop.
3.The screen is black.
I have a question.
should I try the format whole flash option and not format whole flash except boot loader?
I did not try this since latest version doesnt have this.And there are many people who have encountered problems too with that option.
PLEASE HELP ME.THANK YOU.
Click to expand...
Click to collapse
Same problem here did you found any solution to this ?
Hello! I posted on the official forum for Blackview but so far I haven't gotten a response. TL;DR, my phone, a Blackview BV5800 PRO, could not boot up (stuck on logo) and using recovery mode doesn't work. I get mounting issues when I try to factory reset, wiping the partition cache, and even mounting it (an option).
So my last resort was to attempt to re-flash the ROM using the provided ROM file by the OEM, which they did have on their forum. The first time around when I downloaded the ROM plus the SP Flash Tool, followed the instructions and all, it appears to be flashing just fine. As soon as it finished with the checkmark on screen, the phone is stuck in a black screen and Windows keeps detecting the device over and over, but nothing happens on the phone. From my research online, this is a feature of all MediaTek devices in an attempt to restore a factory ROM.
Now, when I try to flash again with the SP Flash Tool with the same ROM, I am getting a "STATUS_DA_HASH_MISMATCH" error. Or sometimes i get the "STATUS_BROM_CMD_SEND_DA_FAIL error. At this point, I tried every possible option within the tool itself as well as trying all combinations on the phone Power + Vol down/up/both then plugging it to my PC, nothing. It keeps showing the same error.
Frustrated with this, did I screw up something? Did the preloader corrupt during the first run? I don't know what to do at this point.
snowlite said:
Hello! I posted on the official forum for Blackview but so far I haven't gotten a response. TL;DR, my phone, a Blackview BV5800 PRO, could not boot up (stuck on logo) and using recovery mode doesn't work. I get mounting issues when I try to factory reset, wiping the partition cache, and even mounting it (an option).
So my last resort was to attempt to re-flash the ROM using the provided ROM file by the OEM, which they did have on their forum. The first time around when I downloaded the ROM plus the SP Flash Tool, followed the instructions and all, it appears to be flashing just fine. As soon as it finished with the checkmark on screen, the phone is stuck in a black screen and Windows keeps detecting the device over and over, but nothing happens on the phone. From my research online, this is a feature of all MediaTek devices in an attempt to restore a factory ROM.
Now, when I try to flash again with the SP Flash Tool with the same ROM, I am getting a "STATUS_DA_HASH_MISMATCH" error. Or sometimes i get the "STATUS_BROM_CMD_SEND_DA_FAIL error. At this point, I tried every possible option within the tool itself as well as trying all combinations on the phone Power + Vol down/up/both then plugging it to my PC, nothing. It keeps showing the same error.
Frustrated with this, did I screw up something? Did the preloader corrupt during the first run? I don't know what to do at this point.
Click to expand...
Click to collapse
hey..
did u solve ur pb..? i have another phone wihch called blackview A60 pro i m getting same error.. it was working fine then suddenly dead..and no flashing or etc..