My device is " 10 or D (3gb) " :
Chipset :- Qualcomm Snapdragon 425
OS :- Stock android was 7.1.2 but, upgraded to 8.1 (Oreo).
Before 10 days i executed a command -- fastboot oem lock -- this command was executed successfully, But after this my device was not booting, when i long press lock button than there was a boot logo for just 0.5 sec and nothing.
After this my device was recognized as -- QH_BULK -- when i installed qualcomm drives, then it was shown as --Qualcomm_Qd_loader 900E -- . I tried some combinations of buttons then finally got --Qualcomm_QD-loader 9008 .
When i searched about "Qd loader 9008" then i found to flash my Stock firmware by QFIL tool. I flashed my Stock rom many times but, also after a successful flash my phone is not booting, also now there is no boot screen after pressing power button. Its now completely black, but charger LED is glowing.
I have still a hope. I searched about my problem, then i found that either my --emmc storage-- is corrupted or the command i executed --fastboot oem lock-- is preventing partitions from overwriting .
Now if my emmc storage is corrupted than i think i have to boot my device from SD Card. Is someone have " emmc.img " of " 10 or D " then please share with me.
Now the situation is, my phone have totally blank screen, LED indicater is glowing red, on connecting to PC Device manager shows it as "Qualcomm_QDLoader 9008",
Also i tried to give a command --fastboot oem unlock-- at this moment. But fastboot is not recognizing my device. On typing --Fastboot devices-- no device is listed.
How could i unlock oem to flash rom.
Hi i download another stock rom of my device which was maybe a fastboot rom because there was a fastboot.bat script in it.
I tried to flash it by miflash tool. Flash took 4 seconds and ended with error message.
After this now my device is recorgnized as
Qualcomm_hs-usb_diagnostic 900E
And now my device started vibrating a little after pressing lock key or volume key
I tried many key combinations but it is not getting qd loader 9008 mode.
I also tried to disconnect battrey connector and then connected to pc but still in 900E mode.
Help me to get 9008 edl mode
Related
Hi,
I unlocked the bootloader for my z5c quite a while ago and am now preparing to flash lineageos.
But unfortunately it's somehow unpossible to enter fastboot mode.
First I tried Vol- and connecting to PC, what never worked. Then via "adb reboot fastboot" - that partially worked, the LED lit blue, but the smartphone wasn't recognized on the PC anymore.
Starting up directly with Vol- + powerbutton would lead into a short bootup (showing Sony Xperia logo).
Then I tried downloading the newest Sony drivers, but on Windows 10 x64 it's not possible to install them (as they are not signed). Therefore I rebooted with signature testing turned off and installed the drivers. Now the smartphone won't boot anymore with blue LED lit, it directly boots into android system.
Next thing I tried was installing flashtool (0.9.25.0) but that won't work either - after installing driver for fastboot etc. the software would take forever to start (see picture 1).
Can anyone help? I'm completely lost
Best,
ssdnvv
Seems I have to enter "adb reboot bootloader" to switch to fastboot mode. With that I was able to flash most recent TWRP 3.2.1.0 and the custom ROM I was aiming for.
hi..
Greetings to every Android Magicians out there...!
Device:- MiA1 (Never rooted)
1.USB debugging was enabled and OEM is not enabled.
2.Hence Boot loader is Locked.
3. Adb drivers installed in my laptop.
4.Windows driver signature are disabled.
5. Xaiomi flash tool and drivers installed.
6. Qualcom HS-USB Diagnostics 900E installed.
7. Can be enter in fastboot mode and edl mode as well.
The problem:- My MiA1 was never rooted (USB debugging was enabled and OEM is not enabled.).
All apps are force stopped suddenly while using the phone so tried to reboot my devices,
and there it begins.. it stuck at boot logo.
Things i have tried:
1. Fastboot Mode:
Since the boot loader is locked i cant flash Any ROM through fastboot so i tried to enter in EDL mode through CMD.,But failed.
so i just open the back panel & however entered in EDL mode by Testpoint.
(and i've tried in fastboot through cmd { fastbooot oem unlock } it says successful but when i check the status through
{fastboot oem devices-info} but the bootloader is still locked).
2. Test Point Method:
I tried to flash MiA1 official global version ROM's (7,8,9 as well) through Xaiomi Flash tool(2015,2016,2017 versions) by test point Methods.
i have encountered the problems like AKC don't match and Cant receive Hello packets.
However i have got solved this Prolems by using Beta version of Xaiomi Flash tool.
3. When i flash (tissot_images_7.8.23_20170823.0000.00_7.1_61cf97d794) flashing was successful but devices still stuck at
Androidone logo.
Tried to flash other versions of ROM (tissot_images_V10.0.4.0.PDHMIXM_9.0) flashing was successful but devices still stuck at
Androidone logo.
By the way i have tried it using different type C cables and different ports (COM5, COM20,COM40 etc) and and different laptop as well but No luck.
i hope you guys do some Magic and help me out.
Thank you so Much for reading this thread.
When my Flashing of stock OS turned to a disaster, Technically my LYF Flame 8 (LS-4505) hard bricked. Not able to boot up, enter recovery or EDL mode. But, somehow I managed to put it on Fastboot mode via Key Combo (Vol Up + Power, then Volume Down + Power). Computer initially detected it is "kedacom android bootloader interface" in Device Manager and Ándroid' in Safely Remove section. Then I updated Kedacom driver to adb driver... Voila... It detects in fastboot mode. But, the problem is that... None of the fastboot commands works. Everything displays same out put " FAILED (remote: unknown command)".
fastboot reboot have success message but, no change happens in Device. CMD test PINS are also available in my device. But, I can't able to bootshoot it.
Device Details :
LYF Flame 8 (LS-4505)
Qualcomm snapdragon 210 msm8909 (4 core)
Battery Detachable.
Need help i cant detect devices after going in fastboot bootloader via adb reboot bootloader, after that cant detect device , i have tried every thing installing adb driver again and updating usb drivers , need help to root phone. its stuck at oppo pass fastboot verify ok ... something like that...please help
Install realme flash tool and jnstall driver
If you see "oppo pass fastboot verify ok" it means you are in fastboot
To reboot back to os press powerbutton+vol. Up
To unloack bootloader:
1.i assume you tried fastboot devices command and you get nothing or <waiting for any device >error. If so open device manager(windows) and check for any unknown devices or android device showing a pop-up error near its icon.
If so you have a driver issue. Mine didn't go away even after updating windows 10 drivers (I had to install windows 7 to unlock it !)
nasir.da.vinci said:
Install realme flash tool and jnstall driver
If you see "oppo pass fastboot verify ok" it means you are in fastboot
Click to expand...
Click to collapse
im facing the same kind of problem since when i rooted my phone i have PBRP recovery on my phon e but i cant go to th recovery mode by my phone like whenever i wanna go there by pressing power button+volume down button it always stuck at a screen saying "Oppo very pass Fastboot_unlock_verify ok" so i always have to go to my recovery mode by using the pc. how to fix the problem?
Ryuk360 said:
im facing the same kind of problem since when i rooted my phone i have PBRP recovery on my phon e but i cant go to th recovery mode by my phone like whenever i wanna go there by pressing power button+volume down button it always stuck at a screen saying "Oppo very pass Fastboot_unlock_verify ok" so i always have to go to my recovery mode by using the pc. how to fix the problem?
Click to expand...
Click to collapse
mine is also showing the same "Oppo very pass Fastboot_unlock_verify ok" how did you solve it?
Things I've done that lead to this:
1. Unlocked bootloader.
2. Added Twrp.
3. Twrp asked for password ( or else it wouldn't decrypt any files) - so to bypass that I tried to use this command: fastboot format userdata . After using that command the phone went completely blank. Couldn't load into fastboot, recovery or anything.
4. My phone was connected to the PC as HS-USB Diagnostics 9008 (COM3) . I tried using blank flash sofiar. And I did it with multiple batch files (different versions of blank flash), and they all succeded and their last comment was "Rebooting to fastboot. Total time: (some time here)". My phone did not boot into fastboot. Now when I connect it to the PC i no longer hear the sound of USB device getting connected, nor I see the HS-USB Diagnostic 9008(COM3) in the Device manager. And when I try to run batch file of a blank flash- it just says " < waiting for device > " .
Any tips on what can I do next, if theres anything left to try?