Related
Thread for hardware mods
POSTING INTERNAL tf101 pictures
like 3g dongle ? internal sd cards? ssd?
removing the battery for 2 HDD 500go?
finding sd cards hubs? usb to sata cables?
? there is a place in the tablet for a 3g dongle?
there are 2 screws under the upper rubbers and the dock open easy
there is a lot of spaces avaible
My MIFI might actually fit in there, all I would need to do is supply it power somehow.
I'm no hardware engineer though, but if thats possible it would save you from the driver issues with a 3g dongle.
I wonder if it would be possible to check which pins from the adapter connect to USB - so we can make DIY USB adapter for those without a dock.
hmm adding an hdd would be very interesting, sata won't be very hard, powersupply will be.
Sent from my O2x with CM7
This is what I was looking for, looking to do some mods to the dock.
Thanks Markolino72.
Internally mount and wire a 32gb memory stick to the USB port so you get a 32gb hard drive added whenever you dock It might even have enough room for a portable USB hub so you don't lose use of the external usb port?
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
ydnality said:
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
Click to expand...
Click to collapse
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Regards.
In regards to the hardware mods, that really looks amazing. Would love to put in my mifi there as well, attach it via USB to charge = your own 3g model Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well. Only a few thoughts.
Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well.
Click to expand...
Click to collapse
it's a good thought but the mifi I have (novatel 2200) wont work without the battery, for some reason if the battery is bad or removed you cannot run usb, it must be the way they have the power run through the battery or charging. Not sure if all are like this or not.
andrewklau said:
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Click to expand...
Click to collapse
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Surprising how much wasted space there seems to be in the dock -- it's nowhere near as tightly packaged as the tablet itself. Looks like Asus can optimize the size or fit some more features in future versions, if they want...
Let me see if I am thinking correctly...Your saying using something like mifi installed via USB wires (will it be always on?) then connect via WiFi on your transformer? So basically your putting the mifi in a case that can never be opened without a screwdriver? I guess one would always have access for your other devices as well as long as the TF is in the vicinity.
P.S. I think I think this is a good idea, not decided though. I like to think of it in a real world application.
there is another post with a guy putting in an SSD, but it bulges at the keyboard. A 32g SD card would be nice.
Sent from my Transformer TF101 using XDA Premium App
typci said:
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Click to expand...
Click to collapse
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
tanguita said:
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
Click to expand...
Click to collapse
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
knoxploration said:
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
Click to expand...
Click to collapse
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
tanguita said:
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
Click to expand...
Click to collapse
Yeah, actually, I hadn't realized that but it does say it clearly on the product warranty page:
"Brazil and South American countries don’t support global service"
http://support.asus.com/warranty.aspx?SLanguage=en&p=20&s=16&m=Eee Pad Transformer TF101
took mine apart also and there is quite a bit of room.
i plan on putting a 128gb usb flash drive inside the dock and soldering onto the usb connections once i get all the bits in.
Any bigger pictures? Are the screws under the rubber feet?
just two screws under the rubber feet near the hinge then it just pulls apart from the top
had to take mine apart as the spring/clip mechanism for the sd card wouldnt lock the card in.
now the card is stuck in with no nails haha a simple fix.
This is good news. I hacked a Crystal HD decoder card (pcie), USB wifi dongle, a logitech nano receiver, and a 4 port micro usb hub (from a touch screen setup) into a Dell mini 9 and there was absolutely no room compared to this.
They even have covers for the USB ports, so if you remove a header and solder wires up you just have to hot glue / epoxy that cover from the back and you are money. Looks clean and stock.
I have an old 64 GB thumbdrive that might find a new home. Maybe a 1.8" usb HDD would fit in there with the battery, without the battery who knows.
Hello , When I first Purchased my Evo 3D, I noticed that any usb cable attached to it would never fit snug it always had movement like wiggled alot. I should have exchanged it but didn;t think it would eventually lead to serious damage until now, well, somehow the first pin on the right broke off and checking online with research it apparently is the +5 of the usb. Which basically screwed me.
I don't have much of an issue with no longer having the usb data sync ability since I can just use a micro SD adapter, and I have an External Battery Charger from Radio shack which helps because I can just charge the batteries with that and insert in my evo3d But the issue I have now is I realize i rely on the 4G tethering ability which i use constantly and it has become a pain to have to run and switch over batteries so my wifi tethering can maintain my computers online.,
Anyway so noticed a few evo 4g mods online where the person would solder two wires one to the negative and other to the 5v positive where the usb is located and then shape the wires nicely and make a custom usb hole somewhere else on the phone and eventually have a usb charging ability similar to one of the attached pictures ( for evo 4g of course not for the 3d)
So anyway i would like to try something similar where i can just locate some solid solder points on the phone and wire up two 5v and ground wires and relocate a custom usb slot somewhere else on the phone, Below is also some zoom closeups of the evo 3d board so my question is any advice to where I can solder the 5v and ground to, I am clueless to where and what points i should try the underside of the usb slot is all metal so seems like not able to solder there maybe on one of the little chips or something perhaps
,, thanks for any help
in reference to the attached images:
the one with the 5v writing is for an Evo 4g Not 3d But Im putting this picture i found online just to give a similar idea of what i need to find on the 3d
the one with the wired shell mod us just Another photo online of what I want to do but once again need the solder points
the other two are the best closeup pictures I could find of the 3d which maybe someone can just point out to me the locations by looking at it, I will take clear zoomed in photos if needed when I have access to a camera at home
thanks anyone for your help!
Why don't you just take it to Sprint and have them repair it? They'll do it for free.
Not from I heard. They charge 100 to fix it. And not even sure they would give me a loaner phone in the meantime. Also , I went into RADIOSHACK and showed and.spoke to one of the reps and he.told me.I wouldhave to pay unless I had their extended warrantee.. I noticed a resistor like chip above.and in front of where the 5v pin is.I wonder if I can solder on that
Sent from hell
suddene said:
Not from I heard. They charge 100 to fix it. And not even sure they would give me a loaner phone in the meantime. Also , I went into RADIOSHACK and showed and.spoke to one of the reps and he.told me.I wouldhave to pay unless I had their extended warrantee.. I noticed a resistor like chip above.and in front of where the 5v pin is.I wonder if I can solder on that
Sent from hell
Click to expand...
Click to collapse
Call sprint and talk to a supervisor. They will send you a new phone or set up repair for free. Call and hang up twice, then call again to get sent directly to a supervisor.
Unfortunately me being a tinkerer ended up breaking off the ground pin and was not able to get serviced , even tried the supervisor and no go, I tried another radioshack and sprint store and of course they noticed it was opened so screwed me out...
anyway,, I taken some fair quality images of the board surface. maybe a +5v location can be pointed out from the images? thanks again
suddene said:
Unfortunately me being a tinkerer ended up breaking off the ground pin and was not able to get serviced , even tried the supervisor and no go, I tried another radioshack and sprint store and of course they noticed it was opened so screwed me out...
anyway,, I taken some fair quality images of the board surface. maybe a +5v location can be pointed out from the images? thanks again
Click to expand...
Click to collapse
I know this is old. But did you ever figure it out? I need a 5v+ location as well. I want to do the inductive charging mod on the 3D.
xkravenx said:
I know this is old. But did you ever figure it out? I need a 5v+ location as well. I want to do the inductive charging mod on the 3D.
Click to expand...
Click to collapse
Instead of making a new thread, I figured I would add to this... I too am trying to mod mine with inductive charging, unfortunately my hands are a little too shaky to solder to the point that I discovered to be continuous with the +5v on the usb port.
I can't really find a clear picture of the PCB anywhere otherwise I would show you, but its about a centimeter or two down from the top left when you open your phone, run your multimeter through those points and you'll find it.
I guess I came here looking for another point..
suddene said:
Unfortunately me being a tinkerer ended up breaking off the ground pin and was not able to get serviced , even tried the supervisor and no go, I tried another radioshack and sprint store and of course they noticed it was opened so screwed me out...
anyway,, I taken some fair quality images of the board surface. maybe a +5v location can be pointed out from the images? thanks again
Click to expand...
Click to collapse
xkravenx said:
I know this is old. But did you ever figure it out? I need a 5v+ location as well. I want to do the inductive charging mod on the 3D.
Click to expand...
Click to collapse
bronx623 said:
Instead of making a new thread, I figured I would add to this... I too am trying to mod mine with inductive charging, unfortunately my hands are a little too shaky to solder to the point that I discovered to be continuous with the +5v on the usb port.
I can't really find a clear picture of the PCB anywhere otherwise I would show you, but its about a centimeter or two down from the top left when you open your phone, run your multimeter through those points and you'll find it.
I guess I came here looking for another point..
Click to expand...
Click to collapse
PLEASE PM me.. those fo you with a broken port, I might have solution for you (nothing shady promise just trying to help where I can, I'll explain once I'm PM'ed). The other guy if all your trying is inductive charging sorry LOL
bronx623 said:
Instead of making a new thread, I figured I would add to this... I too am trying to mod mine with inductive charging, unfortunately my hands are a little too shaky to solder to the point that I discovered to be continuous with the +5v on the usb port.
I can't really find a clear picture of the PCB anywhere otherwise I would show you, but its about a centimeter or two down from the top left when you open your phone, run your multimeter through those points and you'll find it.
I guess I came here looking for another point..
Click to expand...
Click to collapse
Hmm thanks. I will try it when I open the phone. The soldering point should be bigger than the micro-usb pin I would hope.
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
alcapone1130 said:
Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
First, check for disconnected or loose cables inside the gTab.
Next, if it isn't a HW fault like loose cables, then connect the USB cable to the gTab and run this ADB command (you will have to install and set up ADB if you haven't already done so):
Code:
C:\SOME\PATH> [B]adb shell "echo -n 1 > /sys/devices/platform/tegra_touch/calibration"[/B]
Digitizer Cable/Connection
alcapone1130 said:
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
aabbondanza said:
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
Click to expand...
Click to collapse
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Where is the break?
alcapone1130 said:
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Click to expand...
Click to collapse
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
aabbondanza said:
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
Click to expand...
Click to collapse
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
alcapone1130 said:
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
Click to expand...
Click to collapse
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
aabbondanza said:
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
Click to expand...
Click to collapse
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Marketplace & Non Working Tab Links
alcapone1130 said:
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Click to expand...
Click to collapse
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
aabbondanza said:
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
Click to expand...
Click to collapse
Its amazing what a couple of stripped bread ties will doo,lol.I took a bread tie and stripped the paper off of it,cut it to the length I needed and wrapped the remaining wire to one end and pushed the other end of the tie inside the pin hole,lol.It worked like a champ! MY Grab has been up and running for over a month,I just knocked on my coffee table,lol.Thank you for helping me out I really appreciated you trying everything to help me.I am so happy to have it back,now if I can just figure out why I keep seeing black boxes on my games when I play them I will really be doing fine.Thank you again.
Somehow the micro usb port on the phone (the charger) has been mashed up inside, i think it may have been due to someone trying to fit the wrong charger into it.
a shop said it'd have to get sent away,
i was wondering if their is a place to send it to get fixed or it it fixable ?
atm im having to charge another battery with a docking station and swap battery's because it wont charge,
it did work a little earlier on today, charging. but i can see the insides are pretty well destroyed.
it looks like the piece can be removed and a new one soldered on,
any ideas ?
thanks.
Honestly, if somone on here knows how to fix hardware issues I am sure they can lend you a hand but otherwise you will have to go to a repair shop and have it serviced. Just make sure that everything is complete stock and bootloader is in locked state just to be safe. If you don't want to send it back through the mail you can always take to a sprint authorized repair shop.
If you want to attempt it yourself here you go
http://www.youtube.com/watch?v=jxiv3x88eRg
http://www.youtube.com/watch?v=fdxrPWrVgR8
http://www.youtube.com/watch?v=I-HlZQKQzoQ
http://www.ebay.co.uk/itm/New-HTC-E...K_Replacement_Parts_Tools&hash=item20ca337adf
Thanks guys, ive been looking online and some places seem to say they can fix it,
that video is just jokes, he faffs around with the thing im sure he ha no idea what hes doing.
ive found usb ports for other htc models just not the evo 3d.
ive realised it is quite a common problem
its charging via my docking station... just. obviously the internals of the micro usb are mashed up, and i know the replacement needs to be soldered on,
ive looked on some websites but cannot find anywhere to fix it.
its ok atm as its charging via dock, and i have a spare battery, also i can just take out my sd card to add stuff but it i rather annoying abd id like it fixed asap.
You could always use WiFi file explorer,of course WiFi is required but you can read and write the sdcard from your ip address,
Signature (Don't ask me for help, couldn't careless if your phone explodes)
strange thing is its connecting via my dock.. and charging, eventho the insides of the micro usb are mashed up..
it wont work with any other cable just in the dock...
im guessing the dock pin is slightly larger thus allowing a connection ?
Hey all, I'm working on a friend's Verizon V10 (VS990). The flex cable with the actual power & volume buttons is defective. I've scoured eBay and other part sites to find the button assembly. The fingerprint scanner is readily available, but for some reason I'm having a hard time finding the button flex cable assembly. My friend bought the phone secondhand, so he's not sure if he could get LG to fix it without costing an arm and a leg. Does anyone here know of any other good cell phone repair part sites I could check for this cable? Attached is a picture of what I'm talking about. Any help would be appreciated.
Thanks,
DL66
So I answered my own question, apparently. I discovered that the LG part number for this is EAX66848101. I did a search with this part number and found a site in Spain that has the part I need. Sure, it'll be expensive, but still less than LG will probably charge. If anyone else is looking for this part, here's the link to the site I found:
http://www.originalpartsmobile.com/flex-teclado-trasero-lg-v10-h960?filter_name=EAX66848101
darthleland66 said:
Hey all, I'm working on a friend's Verizon V10 (VS990). The flex cable with the actual power & volume buttons is defective. I've scoured eBay and other part sites to find the button assembly. The fingerprint scanner is readily available, but for some reason I'm having a hard time finding the button flex cable assembly. My friend bought the phone secondhand, so he's not sure if he could get LG to fix it without costing an arm and a leg. Does anyone here know of any other good cell phone repair part sites I could check for this cable? Attached is a picture of what I'm talking about. Any help would be appreciated.
Thanks,
DL66
Click to expand...
Click to collapse
Thank you for updating us with very useful info. Some may need it and too many times people are not mindful to be considerate enough to help others when they've solved the problem. Thank you again.
Thanks dude might come handy someday