I Have A MT6580 Chinese Device. Trying To Flash The Stock Firmware Using SPFT And/Or Miracle Thunder. But Everytime I Try To Flash And Connect The USB, SPFT Detects The Device But After A Few Seconds The Device Shows Charging And SPFT Says BROM Download Fail. And Recommends To Check The Power Supply And USB Cable. But Both The USB And Power Supply Are Fine As The Phone Boots Up Properly And I Have Used The Same Cable To Flash My Other Phones. So Could It Be A Hardware Related Issue Or Software Related? Any Idea On Fixing It?
Related
Hello
I have a phone ZOPO C2 VER B. Phone turned off and do not ever want to turn on. It stopped responding to the charger, do not give any sign of life.
When connected to computer detects the phone, installs the drivers, the SP FLASH TOOL it detects. I pulled a few ROMs and I can not upload any ROM. It is always like this: It comes to 100% red belt and that's it. No error. The phone is detected as the MTK PORT, sometimes after reaching the 100% change in VCOM MediaTek USB DA. Here I give a link to the video where you can see how it looks. https://www.youtube.com/watch?v=6Iospu3n0oU&feature=youtu.be
I tried to upload separately preloader, recovery boot. Always the same ending. I tried with the battery in the phone, without the battery, hold Vloume - + Power, etc. Nothing gives all the time is the same.
Use three other PC to try. I have one more phone Zopo and on the same computer and the same driver is dowload rom with SFP without problems.
Phone is brick or can fix this?
Sorry for my english is bad
I am having the same problem, until now could not solve.
Hello to all,
Everything went wrong on flashing with SP Flash tool. The Preloader of Scattered file was checked and all others.
The problem is strange for me and I see that there are other with the same issue without an answer.
Fist of all I did everything described in forums. The driver of MT Preloader Vcom port is installed correctly. In Device Manager LTP com port is detected and as it is normal it disconnects in 2-5 seconds. If I change the USB port on PC it changes the COM port which is the previous detected.
The issue is that my latest SP Flash Tool 5.14 or even 3.13 older one, can't establish permanent connection with the COM port of the MTK 6589. I tested with different cables and different OS (XP and Windows 7 32 bit) on different computers with first pressing Download button of SP Flash Tool and then plugging the cable. If I don't press Volume Down button of my Huawei Ascend G610s it can't be dected of SP Flash. After pressing Volume Down the enters into Meta mode BUT .... SP Flash Tool report:
BROM ERROR : S_BROM_DOWNLOAD_DA_FAIL (2004)
[H/W] Fail to download DA to baseband chip's internal SRAM
[HINT]: 1. There's an cable communication problem between FlashTool and BootROM.
2. Target might be shutdown unexpectedly or target lost power supply.
[ACTION]
1. Try again.
2. Proceed H/W checking in download cable and target side com port.
3. Monitor if power-drop occured in target side.
At some reason COM port is constantly disconnecting and connecting without establishing permanent connection with SP Flash Tool. The red bar pops up and shows 100% done.
Any idea for this issue? You will help a lot of people which don't have the answer what to do.
Best Regards
niki_help said:
Hello to all,
Everything went wrong on flashing with SP Flash tool. The Preloader of Scattered file was checked and all others.
The problem is strange for me and I see that there are other with the same issue without an answer.
Fist of all I did everything described in forums. The driver of MT Preloader Vcom port is installed correctly. In Device Manager LTP com port is detected and as it is normal it disconnects in 2-5 seconds. If I change the USB port on PC it changes the COM port which is the previous detected.
The issue is that my latest SP Flash Tool 5.14 or even 3.13 older one, can't establish permanent connection with the COM port of the MTK 6589. I tested with different cables and different OS (XP and Windows 7 32 bit) on different computers with first pressing Download button of SP Flash Tool and then plugging the cable. If I don't press Volume Down button of my Huawei Ascend G610s it can't be dected of SP Flash. After pressing Volume Down the enters into Meta mode BUT .... SP Flash Tool report:
BROM ERROR : S_BROM_DOWNLOAD_DA_FAIL (2004)
[H/W] Fail to download DA to baseband chip's internal SRAM
[HINT]: 1. There's an cable communication problem between FlashTool and BootROM.
2. Target might be shutdown unexpectedly or target lost power supply.
[ACTION]
1. Try again.
2. Proceed H/W checking in download cable and target side com port.
3. Monitor if power-drop occured in target side.
At some reason COM port is constantly disconnecting and connecting without establishing permanent connection with SP Flash Tool. The red bar pops up and shows 100% done.
Any idea for this issue? You will help a lot of people which don't have the answer what to do.
Best Regards
Click to expand...
Click to collapse
I have the same problem please help
Hi ...what is the phone model?
In my case the issue was solved with a hardware "kick" with button combination because at some reason the MTK preloader was put the phone in nonsense turning on and off the without being able to establish permanent connection. I tried all the MTK drivers but the issue was some kind of bug which actually was constant switching off. My model phone was Huawei G610s. What I did was to hold Power, +, - button together for about 5 seconds then release power still holding + and - button, and after 4-5 seconds release + button while holding - button for 4 seconds. This kicked out from the constant disconnection and SP flash tool was able to finalize the flash. Without this every time the error was as your have described.
I have a Digicel DL750. I understand that it is an Alcatel Pop C3 upgraded to a KitKat.
My phone is hard bricked. I followed the procedures to connect it to the PC whilst off and without battery. Nothing happens. No connecting sound on my PC... until I hold the power, volume up and volume down buttons.
My sister has the same phone. Hers connect whilst off and without battery. I even see the MTK Preloader in the device manager, so her phone connected successfully. For me what shows up is Alcatel Mobile Phones (COM5) and after reinstalling the driver I see MTK USB Port.
I have the Sp Flash Tool-ready files to flash unto the device.
I just need the phone to connect like it should. Can you assist me?
Is my phone dead?
My vivo Y55L was stuck in a boot loop and did not go ahead of the vivo screen.
I tried flashing the stock ROM through QFIL but it gave me a EDL Firehouse error and the flash was unsuccessful. I disconnected the phone to reconnect but to my misery the phone does not connect to QFIL anymore. When i press the power up and down button and connect the USB the computer gave me an error USB device not recognised and may have malfunctioned. if I power up the phone now it doesn't start and goes back into the bootloop for 2-3 times before switching off. I have tried reconnecting the USB and reinstalling ADB drivers and Qualcomm drivers. But still the same error, Device receptor not recognized and USB device not recognized may have malfunctioned. Any solutions will be appreciated
I was installing software in my device by odin suddenly the cable is detach and my device nothing is happening in my device
only shows a black screen.
when i connect my device to pc it connect and disconnect automatically after 2 sec.
I install all usb software and preloaders still device is connecting and disconnecting.
I also use sp tool to download preloader nothing happen.
remove baterry insert battery.
change pc,laptop,usb cables. noting happen . can anybody help me ????:silly::silly: