PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
your not the only one with this problem i have it too with same mt6575 someone help please
Need to uninstall device and reinstall drivers
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
ronbo76 said:
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
Click to expand...
Click to collapse
Your USB program does give a lot of information I have never seen before, but I still haven't been able to figure out how to get the driver to load.
thanks, John
I'm having the same problem installing the MT6575 USB VCOM drivers. Is there a workaround to get this installed? I"m using WIN 6 64bit
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
ivy13 said:
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
Click to expand...
Click to collapse
Tried your first method but still get Code 10 error. Could not understand your second method. Please help. Me device is Qmobile Noir A2
hye.. any progress? am having the same issue.. just for MTK6575 com port driver
Just made my Amoi N820 work
So happy
You get Code 10 becouse your windows couldn't recognize the driver but that's irrelevant becouse flashing will work
No solution?
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
orion~X said:
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
Click to expand...
Click to collapse
i have thet problem to.
is ther solution?
I HAVE SOLUTION FOR THIS PROBLEM!!
Just ignore the error Code 10! Start the SPFlashtool and load the scatterfile, click on download and connect your switch off Phone with the computer. It will work fine.
Having the Same Problem
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Hi.
me test for me not work.
iphone 4s.
plz help me.
hihi2u2 said:
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Click to expand...
Click to collapse
Did you ever get this problem solved as I have the same issue with an MTK 6592 chip based phone?
I have the same problem too.
Installation of Media Tek preloaded drivers gives me Code 10 error.
Has anyone found the solution?
my phone is totally dead without power now after I tried to flash with SP Flash tool using correct ROM. I noticed in device manager that there is a CODE 10 error in mediatek preloader usb driver.. is this the culprit? my phone can no longer be detected now in SPFlash or MTK Droid tools... so hopeless... this is a brandnew phone I bought to be given as gift to my cousin...
I did it! I did it! I did it!
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
I've been struggling with my UMI Rome for days. It has/had the black screen problem, sometimes won't enter recovery mode, sometimes wouldn't allow charge, sometimes works just fine (yesterday). Last night i mistakenly cut off power during a battery recharge. -- today it has all the above problems (bricked) so I am trying doing a flashing again using the tutorials and tools on the Tehnotone.com site. Sintetix's reply above helps me at least have a better clue on what is going on. Wish me luck! BTW, I am using a Dell Windows 10 pc. (Results to be reported here.)
Sintetix said:
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
Click to expand...
Click to collapse
I tried what you said. It wouldn't install properly. It kept saying error (code 10) and showed in device management with a caution sign every time I installed the driver. I disabled the forced driver signature thingamabop but it still does it. I guess I'm screwed. Has anyone else fixed this?
Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Tomaskaos said:
Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Click to expand...
Click to collapse
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
SubwayChamp said:
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
Click to expand...
Click to collapse
Thanks!!! It works!!!!
Just be very careful. The USB C connector port in the phone is very loose... so make sure you can hold the cable tight other wiser it will lose the connection and brick your phone. For me, I had to remove the Plastic cover to be able to hold the power cable tight!
Hi, could you help me please? I did your steps, but it is not working. Sp flash does all its job, shows the green sign, but the phone stills dead. What I noticed the usb connects with the phone, then it disconnects. I tried to install the drivers as the tutorials say like deactivating the driver signature enforcement, but nothig happens well.
I'm trying to install stock rom to Lenovo a2016a40 (Lenovo B). After I connect phone to my system using volume down key preloder appears in device manager but after few seconds it disconnects from pc. I have tried to install via SP flash tool but it fails and gives error.
I have tried to update all mediatek drivers , changed port and cables but still I'm facing that issue , please help with this issue.
@sangram200
AFAIK Lenovo Vibe B is based on Mediatek chipset, hence SP Flash Tool seems to be the correct one.
It just disappeared from Device manager on PC
It simply disconnects from pc after few seconds ( disappeared from device manager), hense SP tool fails there is no issue with flash tool , its the connectivity issue but I don't understand why it disconnects from PC ,I have tried to update drivers and changed cables and switched ports but still having same issue.
@sangram200
I'm pretty sure you haven't installed the correct USB-drivers as needed, for example the MediaTek MT65xx USB VCOM Driver: this USB Driver will make sure that your MediaTek Android device is properly recognized by your PC, it ensures that there will be no hiccups while you are trying to flash a custom ROM or when you are trying to root your device.
I'm trying to clone the phone disk by using https://github.com/bkerler/mtkclient.
It's working flawlessly using the command mtk rf, but I terminate the program using Ctrl+C because I need to clean my pc drive first.
I don't think this would cause problem since it's only read operation.
When I try to reconnect using mtk again, It's shows error on DA_send, then handshake failed and finally, the phone shows no life, since mtk doesn't even detect it again.
I'm running dmesg to check if my linux desktop detect the usb device and it shows.
Code:
device descriptor read/64.
Device not responding to setup address.
device not accepting address X, error -71
unable to enumerate USB device
Is the phone dead?
Is it on BROM mode or something else?
I've read on some forum to press all button for 15s it did not work. and prying the battery is above my ability right now.
Any helps is appreciated, thanks!
I have usually have good response from LONG press power button. Sometimes it takes 30Secs or more to reset from brom. (not same device though)