I bought and unlocked Galaxy S7 to get service on Tmobile network and the phone works fine but is an AT&T phone with
all the accompanying bloatware. I am in a bad cellular area for tmobile and depend on wifi calling as the signal is very weak.
The wifi calling on my purchased phone is grayed out which i found out through forums that AT&T has something to do with this.
I decided to root my phone and load firmware to Tmobile but have only found the process and firmware SM-G930T and not SM-G891T. The phone currently has SM-G891A, which is AT&T 's firmware. Baseband version G891AUCS4DRK1. I haven't been to find the right firmware for my phone. Can anyone help me? Thanks
ghat01 said:
I bought and unlocked Galaxy S7 to get service on Tmobile network and the phone works fine but is an AT&T phone with
all the accompanying bloatware. I am in a bad cellular area for tmobile and depend on wifi calling as the signal is very weak.
The wifi calling on my purchased phone is grayed out which i found out through forums that AT&T has something to do with this.
I decided to root my phone and load firmware to Tmobile but have only found the process and firmware SM-G930T and not SM-G891T. The phone currently has SM-G891A, which is AT&T 's firmware. Baseband version G891AUCS4DRK1. I haven't been to find the right firmware for my phone. Can anyone help me? Thanks
Click to expand...
Click to collapse
Are you sure you didn't confuse device version with firmware version? SM-G891A
Is not a firmware, it's your phone model, which is of course galaxy S7.
But anyway, there is not Tmobile firmware for that model. Only 930T as you said.maybe could be possible to port the rom.
Can I use the firmware for the sm-g930t on the sm- g891a
eduardvi995 said:
Are you sure you didn't confuse device version with firmware version? SM-G891A
Is not a firmware, it's your phone model, which is of course galaxy S7.
But anyway, there is not Tmobile firmware for that model. Only 930T as you said.maybe could be possible to port the rom.
Click to expand...
Click to collapse
My question is, can I flash the rom on a sm-g891a with firmware for a sm-930tin
ghat01 said:
My question is, can I flash the rom on a sm-g891a with firmware for a sm-930tin
Click to expand...
Click to collapse
I wouldn't recommend to flash it yet. Processors should be the same, as well as the screen size,for flash a different rom.
eduardvi995 said:
I wouldn't recommend to flash it yet. Processors should be the same, as well as the screen size,for flash a different rom.
Click to expand...
Click to collapse
All the components are the same except for the battery size, hardened case and shatter proof screen
ghat01 said:
All the components are the same except for the battery size, hardened case and shatter proof screen
Click to expand...
Click to collapse
If battery isn't the same, power consumption could burn the phone.
Related
Is it possible to flash SM-G965U (T-Mobile) unlocked with SM-G965U1 stock unbranded (CSC: XAA) firmware?
If possible. How.
Pls help.
mohibd73 said:
Is it possible to flash SM-G965U (T-Mobile) unlocked with SM-G965U1 stock unbranded (CSC: XAA) firmware?
If possible. How.
Pls help.
Click to expand...
Click to collapse
Yes. It is possible. But what are you trying to gain? TMO is one of the friendliest carriers to Samsung unlocked phones. You already get VoLTE and Wi-Fi Calling. VVM is available via Play Store app. That's probably the one carrier where I would never consider flashing branded firmware.
If you really want to do it, just flash U firmware with normal (not HOME) CSC. You can get it from lots of places like SamFirm or the various firmware websites.
Be sure to use the 3B patched 3.13.1 Odin found elsewhere on XDA.
Thanks for the information. I have unbranded my SM-G965U to SM-G965U1.
OK so I have a T-Mobile SM-G965U. I can flash the room and get a different rom on the phone? I though that I had to root the phone in order to install another rom.
Is there a rom that focuses on Tethering my phone data, under the phone datas apn.
One thing I can't figure out, there are so many developers, but there hasn't been a solid app , that can bypass signature checking and use the phone native hotspot feature under the phones data APN not the hotspot APN, so that it hot spot data comes up as phone data.
There has to be someone lol
Dasin said:
OK so I have a T-Mobile SM-G965U. I can flash the room and get a different rom on the phone? I though that I had to root the phone in order to install another rom.
Is there a rom that focuses on Tethering my phone data, under the phone datas apn.
One thing I can't figure out, there are so many developers, but there hasn't been a solid app , that can bypass signature checking and use the phone native hotspot feature under the phones data APN not the hotspot APN, so that it hot spot data comes up as phone data.
There has to be someone lol
Click to expand...
Click to collapse
You certainly don't need root to run a different firmware provided by Samsung for your hardware model. To do anything else, ROM-wise, you do need root. That doesn't exist for this model. Something like hijacking the APN in the manner you describe requires root. Your only hope is an app like PDANet that consumes phone data and provides it through another means like USB tethering. I think they have some support for Wi-Fi as well, but read up on that.
It's been forever since I've been here, missed this place. I am practically a noob now.
Here is my scenario:
I have a Verizon-branded S9+ / SM-G965U on the firmware/baseband G965USQ3BRK2. It is paid off, assured it is carrier unlocked and has also never been modified, pure stock. I'm looking to switch carriers from Verizon to another service. It's also my understanding that Verizon phones are a pain in the hiney and there may be issues with data, features, and other nags and warnings because a non-Verizon SIM is in use. Had an S5 that worked on other carriers but was a nightmare to configure.
Will I be condemned to a similar nightmare of nags and warnings, or will it rebrand it's self and allow me to receive OTA updates on the new carrier? Just not sure of what my options are, the search results yields conflicting information where some had to flash some firmware and others didn't.
Any recommendations would be appreciated.
I converted an unlocked Verizon S9+ to an unbranded, unlocked device, using it on T-Mobile and couldn't be happier with it. You have the option of flashing your own carrier's firmware or the factory unlocked, and it will improve your situation, no more SIM card notifications and all that.
P.S. I was in the same situation as you, used to be on here all the time but felt like a noob all over again. But a super helpful member here guided me through the process and it was completely painless, one quick flash with Odin and it was all good.
YrrchSebor said:
I converted an unlocked Verizon S9+ to an unbranded, unlocked device, using it on T-Mobile and couldn't be happier with it. You have the option of flashing your own carrier's firmware or the factory unlocked, and it will improve your situation, no more SIM card notifications and all that.
P.S. I was in the same situation as you, used to be on here all the time but felt like a noob all over again. But a super helpful member here guided me through the process and it was completely painless, one quick flash with Odin and it was all good.
Click to expand...
Click to collapse
Thanks! Do you have any recommendations where I can find an up to date guide for flashing 8.0 devices?
Dr.Gonz0 said:
Thanks! Do you have any recommendations where I can find an up to date guide for flashing 8.0 devices?
Click to expand...
Click to collapse
Welcome. Looks like there's some instructions here: https://forum.xda-developers.com/ga...icial-stock-firmware-thread-samsung-t3764479. However you will want to make sure you find the patched version of Odin to get past the fact that you are flashing a different firmware than is currently on the phone. And you will want to flash G965U or U1 firmware, that also has a 3 as the fifth number from the end, just as the firmware that's already on your phone.
YrrchSebor said:
Welcome. Looks like there's some instructions here: https://forum.xda-developers.com/ga...icial-stock-firmware-thread-samsung-t3764479. However you will want to make sure you find the patched version of Odin to get past the fact that you are flashing a different firmware than is currently on the phone. And you will want to flash G965U or U1 firmware, that also has a 3 as the fifth number from the end, just as the firmware that's already on your phone.
Click to expand...
Click to collapse
Thanks for your help and for answering the questions.
Is there any benefit to flash U1 or would just U work?
Would the firmware downloaded using SamFirm work with that version of ODIN you linked?
Do I have to go through a rooting process and install TWRP prior to going ODIN on my phone? Or can I just go into download mode on my device, click yeah about a custom OS, then do the ODIN bit?
Dr.Gonz0 said:
Thanks for your help and for answering the questions.
Is there any benefit to flash U1 or would just U work?
Would the firmware downloaded using SamFirm work with that version of ODIN you linked?
Do I have to go through a rooting process and install TWRP prior to going ODIN on my phone? Or can I just go into download mode on my device, click yeah about a custom OS, then do the ODIN bit?
Click to expand...
Click to collapse
The U firmwares are those from carriers and the U1 is from the factory unlocked unbranded variant. so it's up to you if you want your carriers own firmware or just a generic Samsung version. If you need Wi-Fi calling and or volte, there might be a better chance of it working with your carriers firmware but the unlocked firmware does a good job with that as well, I have both of those features working perfectly with the U1 firmware and a T-Mobile SIM. Just make sure to use the CSC as opposed to HOME_CSC, so that your phone is fully wiped and configured for your sim card. I will say one advantage of the unlocked U1 firmware is free built-in caller ID ?
No rooting necessary, in fact it's not even possible on the US models, so just boot into Odin and flash the firmware using the patched version of Odin.
I'm looking for the latest USA factory unlocked firmware for the Stylo 4 (KDZ file), does anyone know where I can find that? I have looked everywhere I can think of and everyone has carrier specific firmware, but not the one I am looking for.
The specific model is LMQ710ULM.AUSABK.
The IMEI is: 357183090498307
Try This
SpikeyPsyche said:
I'm looking for the latest USA factory unlocked firmware for the Stylo 4 (KDZ file), does anyone know where I can find that? I have looked everywhere I can think of and everyone has carrier specific firmware, but not the one I am looking for.
The specific model is LMQ710ULM.AUSABK.
The IMEI is: 357183090498307
Click to expand...
Click to collapse
Hi there,
I would like to know which specific carrier that your looking for.
Sincerely
KIBS2173
KIBS2173 said:
Hi there,
I would like to know which specific carrier that your looking for.
Sincerely
KIBS2173
Click to expand...
Click to collapse
It is the unlocked model sold directly by LG in the USA, so it is non-carrier firmware.
Try This
SpikeyPsyche said:
It is the unlocked model sold directly by LG in the USA, so it is non-carrier firmware.
Click to expand...
Click to collapse
Hi there,
You can try this website.
https://lg-firmwares.com/
or
https://lg-firmwares.com/lg-lmq710ulm-firmwares/#tab=firmwares
since your phone is network unlocked I think it might be safe to reinstall the firmware.
However, if you have your doubts feel free to search it online or ask LG directly.
Sincerely
KIBS2173
KIBS2173 said:
Hi there,
You can try this website.
https://lg-firmwares.com/
or
https://lg-firmwares.com/lg-lmq710ulm-firmwares/#tab=firmwares
since your phone is network unlocked I think it might be safe to reinstall the firmware.
However, if you have your doubts feel free to search it online or ask LG directly.
Sincerely
KIBS2173
Click to expand...
Click to collapse
Thank you. I found out that they never released the KDZ for the factory unlocked phones (region USA). So, the only way to update my phone would be to flash carrier firmware, which, is kinda risky, since it would technically be a crossflash. I would likely lose certain features, such as Wi-Fi calling and/or VoLTE. One of the few firmwares that supports wi-fi calling is the T-Mobile firmware, but I wouldn't flash that firmware because it is different than the hardware of my phone (their model has 2 GB of RAM, mine has 3 GB of RAM, etc...
Try This
SpikeyPsyche said:
Thank you. I found out that they never released the KDZ for the factory unlocked phones (region USA). So, the only way to update my phone would be to flash carrier firmware, which, is kinda risky, since it would technically be a crossflash. I would likely lose certain features, such as Wi-Fi calling and/or VoLTE. One of the few firmwares that supports wi-fi calling is the T-Mobile firmware, but I wouldn't flash that firmware because it is different than the hardware of my phone (their model has 2 GB of RAM, mine has 3 GB of RAM, etc...
Click to expand...
Click to collapse
Hi there,
Yes, while I was researching it online I found two firmware for this phone for the US region. But anyways have you tried using a PC suite from LG to reinstall the firmware. Or have you tried going on to the recovery mode and just reset the whole device. Or better try to install a custom ROM, to be honest I think it might be okay if you flashed a Europe region firmware, but make sure you back up the current firmware. I flashed a Samsung phone which was used to be locked and then I unlocked it after that I flashed the carrier firmware and it didnt carrier locked my phone. But anyways try your best.
Sincerely
KIBS2173
Hi. I want to flash a Brazilian firmware (dual SIM) into my US hardware (single SIM). Both are Snapdragon. Reason is that I want to use the Brazilian Samsung Pay. Bough the phone in the US but I live in Brazil.
Can I flash THIS ROM without problems? Will it trigger Knox? Any loss in functionality?
Thank you all.
gustavrsh said:
Hi. I want to flash a Brazilian firmware (dual SIM) into my US hardware (single SIM). Both are Snapdragon. Reason is that I want to use the Brazilian Samsung Pay. Bough the phone in the US but I live in Brazil.
Can I flash THIS ROM without problems? Will it trigger Knox? Any loss in functionality?
Thank you all.
Click to expand...
Click to collapse
no
gustavrsh said:
Hi. I want to flash a Brazilian firmware (dual SIM) into my US hardware (single SIM). Both are Snapdragon. Reason is that I want to use the Brazilian Samsung Pay. Bough the phone in the US but I live in Brazil.
Can I flash THIS ROM without problems? Will it trigger Knox? Any loss in functionality?
Thank you all.
Click to expand...
Click to collapse
not possible. also, is there not a CSC for your area you can flash instead?
I don't know why these guys say it's not possible, maybe it isn't with your model. I also don't want to give you any bad ideas or anything, so use your own discretion & research.
My phone was unusable when I did this, so I had nothing to lose when I did this (It worked though).
I easily flashed my canadian note 8 with a us firmware using modified odin (must be same version bootloader).
It has warranty status 0x0 (aka, Knox is NOT tripped).
AGAIN, I'm not advising you try this with your model, unless you know what you're doing. I just want to make the information available to you.
Edit: I'm just waiting for someone to upload snapdragon beta 3 one ui 2.0. I'm going to try the same method to convert my Canadian s9+ to USA version.
Edit 2: I can confirm this method works on my Canadian s9+ aswell.
Amb669 said:
I don't know why these guys say it's not possible, maybe it isn't with your model. I also don't want to give you any bad ideas or anything, so use your own discretion & research.
My phone was unusable when I did this, so I had nothing to lose when I did this (It worked though).
I easily flashed my canadian note 8 with a us firmware using modified odin (must be same version bootloader).
It has warranty status 0x0 (aka, Knox is NOT tripped).
AGAIN, I'm not advising you try this with your model, unless you know what you're doing. I just want to make the information available to you.
Edit: I'm just waiting for someone to upload snapdragon beta 3 one ui 2.0. I'm going to try the same method to convert my Canadian s9+ to USA version.
Edit 2: I can confirm this method works on my Canadian s9+ aswell.
Click to expand...
Click to collapse
Yeah I don't think it'll work on mine, since it's a single sim phone, and the ROM I wanted was for a dual sim version. Unless of course the hardware is the same and the second SIM slot is present. I could try, but I don't want to risk it. Maybe later when Sammy stops updating the phone.
Youdoofus said:
not possible. also, is there not a CSC for your area you can flash instead?
Click to expand...
Click to collapse
Unfortunately not. The SM-G965U1 is the US unlocked version. There are only CSCs for American carriers.
gustavrsh said:
Yeah I don't think it'll work on mine, since it's a single sim phone, and the ROM I wanted was for a dual sim version. Unless of course the hardware is the same and the second SIM slot is present. I could try, but I don't want to risk it. Maybe later when Sammy stops updating the phone.
Unfortunately not. The SM-G965U1 is the US unlocked version. There are only CSCs for American carriers.
Click to expand...
Click to collapse
if its truly unlocked, then you should already have the U1 firmware on it. Get modded Odin and the U1 firmware, flash it in Odin and go from there. I never looked back after ditching the carrier junk on my phone
Sometime ago I did somethinh like that on my Arabian S7 Edge that I bough in Paraguai, it was Dual Sim model and i flashed ZTO CSC via Odin, and the phone was working well, but i'm not sure if the reverse works, and even the models were similar (F vs FD version) in your case u have 965U vs 9650, I would not take that risk, i thing that a korean or chinese model is 9650 too
look at this picture, US version has more bands so the modem could be different, you can try but you're risking your phone
davenasc said:
look at this picture, US version has more bands so the modem could be different, you can try but you're risking your phone
Click to expand...
Click to collapse
yep, they are different phones that just so happen to use the same processor. Different bootloader, same chassis for whatever reason. Anyways, there have been threads talking about converting the 9650 to a 965u, but ive never seen anyone confirming that it indeed works. Big risk, but as long as one can get back to Odin mode, one should be good.
Hello, looking for some help to see if anyone can help me find the firmware of my A526U specifically for AT&T? I have moved my phone over from TMobile where I purchased it from, and am looking to re-flash it to AT&T. Was working fine for a few months, now I'm no longer able to make or receive calls.
After inserting the new AT&T SIM card, the TMobile splash screen still shows up. The Service Provider software version reflects TMobile still as well and I'm concerned that for whatever reason the phone did not fully update after inserting the new SIM. I spent 2 hours on the phone with AT&T support after the store said they couldn't help me. Pulled the SIM card out, restarted phone, put it back in, reset network settings etc. I've searched sammobile and I cannot find the AT&T firmware, only TMobile, Sprint, and TMK. I would sincerely be greateful please if anyone could help me by pointing me in the right direction for the firmware for this model phone.
AT&T doesn't make their firmware available publicly - for any device. I have a source who can get me Samsung firmware for any USA device - even AT&T. But he charges me for each one
I appreciate the quick response! Is there any option I have here? Could I try flashing a "U1" firmware to his phone then? He's currently on A526USQS4CVA6. I actually found your other post as I was also working on my note 10 plus - https://forum.xda-developers.com/t/n975u-and-n975u1-firmware-links-here.3957648/. If I'm reading that correctly, I should be able to correct? If so, how can I tell if the version I'm downloading is "downgrading the bootloader"
aschaffer35 said:
I appreciate the quick response! Is there any option I have here? Could I try flashing a "U1" firmware to his phone then? He's currently on A526USQS4CVA6. I actually found your other post as I was also working on my note 10 plus - https://forum.xda-developers.com/t/n975u-and-n975u1-firmware-links-here.3957648/. If I'm reading that correctly, I should be able to correct? If so, how can I tell if the version I'm downloading is "downgrading the bootloader"
Click to expand...
Click to collapse
1. Yes, you can try flashing U1 if you want
2. You can't "downgrade the bootloader" - Odin won't let you.
3. In A526USQS4CVA6, "4" is the position of the bootloader level/revision/binary. Make sure that whatever U1 firmware you download also has a 4 in that spot and you'll be fine. (Or just get the firmware from Frija or one of the other similar firmware download tools, because those throw you whatever the newest version is automatically)
iBowToAndroid said:
1. Yes, you can try flashing U1 if you want
2. You can't "downgrade the bootloader" - Odin won't let you.
3. In A526USQS4CVA6, "4" is the position of the bootloader level/revision/binary. Make sure that whatever U1 firmware you download also has a 4 in that spot and you'll be fine. (Or just get the firmware from Frija or one of the other similar firmware download tools, because those throw you whatever the newest version is automatically)
Click to expand...
Click to collapse
Thank you very much sir! I shall give this a go this weekend! You guys rock!
My AT&T N10+ N975U is running on Pie. It transitioned seamlessly with no changes made on my end. It was already using 4G VoLTE though. Same sim card.
I would contact AT&T advanced tech support as there may be an easier way.
4G VoLTE needs to be enabled in hidden settings.
blackhawk said:
My AT&T N10+ N975U is running on Pie. It transitioned seamlessly with no changes made on my end. It was already using 4G VoLTE though. Same sim card.
I would contact AT&T advanced tech support as there may be an easier way.
4G VoLTE needs to be enabled in hidden settings.
Click to expand...
Click to collapse
Your AT&T phone? So it's originally an AT&T model that you're still using with them? That's not the same situation that the OP is in
iBowToAndroid said:
Your AT&T phone? So it's originally an AT&T model that you're still using with them? That's not the same situation that the OP is in
Click to expand...
Click to collapse
The U is the AT&T variant vs the U1 which is the unlocked variant, correct?
blackhawk said:
The U is the AT&T variant vs the U1 which is the unlocked variant, correct?
Click to expand...
Click to collapse
Yup. But OP has a T-Mobile model that they moved to AT&T. There's also no guarantee that a Note 10+ will work the exact same way as an A52. You're also running 3 year old firmware, while OP is fully updated.
So i don't see the correlation.
iBowToAndroid said:
Yup. But OP has a T-Mobile model that they moved to AT&T. There's also no guarantee that a Note 10+ will work the exact same way as an A52. You're also running 3 year old firmware, while OP is fully updated.
So i don't see the correlation.
Click to expand...
Click to collapse
The old firmware works fine on 4G VoLTE... that's likely not the issue. What is the issue is it wasn't running on 4G VoLTE so it's likely the settings and sim card need updating not the firmware.
Hi All, thought I would provide an update... After spending hours on the phone with AT&T support this week and being frustrated with the AT&T store, I decided to proceed forward with flashing the U1 version. What started this all was last week my son could no longer make or receive calls on his AT&T A52 phone (we ported it from TMobile September 2021). The store and AT&T advanced tech support said there were issues with people's BYOD devices, even though the A526U and A526U1 shows on the supported devices list. The store rep said he's been getting people in left and right that can't make or receive calls, and all they can do is upsell customers to an AT&T branded phone.
SO... my son's phone was on A526USQS4CVA6. Startup screen showed TMobile still, even with the AT&T SIM card in it. I proceed to flash the A526U1OYM4CVB2_ATT that I found from Sammobile. Was hoping someone had just the "U" version but I couldn't find this anywhere. When doing the flash, I used the Home_CSC file (I had to download a patched version of ODIN as it was stuck as setting up connection) and when it finished it would just keep going back to the download screen on the phone and I freaked out. I did some more research and decided to flash again using CSC instead of Home.CSC (I did a backup using smart switch on my PC luckily). This WORKED! I'm guessing because the software version he was on was different than what I was trying to flash too so maybe this is why I needed the CSC for a clean flash (there was no user data file that downloaded from SAMMOBILE).
Now, calls are working on my son's phone again! AND his service provider software version now reflects ATT vs TMB! Man this has been one heck of a journey lol. I've seen numerous forums on google of people having the same trouble with me, their BYOD devices not working. Seems a flash of U1 worked for me, so hopefully this helps others out there!