Related
Hi,
I would very high appreciate if someone in this community could help me with the Hard-SPL upgrade problem. I read a lot of threads in this forum and in other forums. I tried to follow several solutions but I get stuck all time during the upgrade to hard spl 2.10 with an error 260.
I connected my mobile via USB cable. WMGC 6.1 is running on my PC --> synchronizing has finished. Then I started Ruuwraper on my vista PC --> after I answered yes to upgrade to hard-spl 2.10 --> on my mobile appeared enterBL.exe and was asking me if I should run it Y/N. Then I replied with yes --> afterwards it appeared the bootloader
IPL-SSPL by Desc
SPL-1.09ds
but then there is no reaction for about half a minute. Afterwards it appears on the PC "error 260" (I should check if the cable is connected via USB)
However I see that USB appears on the bootloader screen. In my opinion it should work, but didn't !
if I go into bootloader I read following :
IPL --> 1.01
SPL --> 1.04
IMG 1.23.707.4
My desktop OS --> vista 64
windows mobile center --> V6.1.6965
Can it be that I need a special USB cable for my HTC ?
Or ????
Thanks in advance for your help.
I know that there is a problem with using 64bit OS versions, so if you have another computer you can use that isn't 64bit to check whether it is that or not.
Good luck
Thanks for your fast reply.
I tried on my other computer (laptop installed windows XP SP3). However I failed with the same problem.
When i first tried to flash my device i had a problem of it not connecting to the boot loader, it seemed that every time the phone changed to boot loader the computer would no longer recognize it and it wouldn't be synced with the computer. i think i managed to get around this problem by putting my phone into boot loader (ok button + power + reset button) and then connecting it for some reason the computer would then recognize it and it would work. I cant remember what it was i was flashing it may have been hard-spl
Hope this helps, Good luck
Edit: I found this information on completely different forum that came from HTC about what to do
HTC's Answer: I was instructed to disconnect and soft-reset. Then I was instructed to go to Settings>System>Memory>Running programs and Stop All. Including Active Sync. We then reconnected the phone. Established a sync and ran the utility. Active Sync still goes away and you get the falling tone of a Disconnect. Ignore it and proceed as if everything is connected. Bang Zoom. 10 minutes later I'm loading software. *dance*
Click to expand...
Click to collapse
this is what is meant to happen as i flashed a new rom the other day on vista and windows had to find the device again and reconnect i think after this small pause it worked again.
Ok, I tried. Following result :
I see that Serial goes to USB but then no reaction. I can see on the WMDC 6.1 --> it shows still "not connected".
I found one article below and tried as well but it starts not automatecly from the bootloader too :
HERMIMG.nbh on a FAT32 filesystem
http://forum.xda-developers.com/files/hermes_sd_flashing.jpg
1. If you want to install any ROM (NBH) which is not supplied by your operator or the CID does not match then you will need to SuperCID your device. This can be easily done by installing HardSPL and should be the first thing done if doing any upgrading.
2. Empty (erase the contents) of your 2 gig or smaller non-SHDC MicroSD card (the Hermes bootloader does not support SDHC) from the Windows Mobile file explorer or format it from your computer using a card reader (in some cases format doesn't work) make sure it's formated in FAT32 format. As a precaution you might want to check the MicroSD card for file errors. i.e (Properties->Tools->Error Checking)
3. Extract the .NBH file from your preferred ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
4. Rename the .NBH file to HERMIMG.nbh and copy it to the root folder of your microSD card.
5. With microSD card inserted on the phone, start the bootloader (hold Ok button on left side and POWER button at same time and stick with stylus in RESET on bottom).
6. You should see a screen similar to the one pictured on the left (What lines appear depends on what is included in the nbh. If the file doesn't include bootloader code, that line will not appear, and so on.) Confirm flashing on screen by pressing the power button.
7. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
8. After you get the confirmation that the upgrade is complete, softreset your device.
So you tried flashing using the sd card method and still no result?
yes
and now I tried your suggestion with stop running programs activsync and calender.
Also the same --> error 260
I would've hoped that one of the methods would work, i take it the device syncs up fine normally to device center and you can access all your files etc?
This is the thread i quoted from there is some more information about the problem i don't know whether it will help though.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=42389&view=by_date_ascending&page=1
yes I can synchronize and I can see all the file via vista explorer.
I take it your planning to flash a newer rom onto your hermes, are you running the stock rom that came with it at the moment?
I just ran the hard-spl ruuwrapper.exe on my computer with out my phone connected this gave me the 260 error so it is most probably something to do with the phone connecting whilst in boot loader mode, did you click yes to run any program that it asked you to on the phone?
I did read some where that resetting the pc might work but i dont know whether it will make a difference considering you've already tried it on another computer.
Good luck
See my comments inline :
Scotty93 said:
I take it your planning to flash a newer rom onto your hermes, are you running the stock rom that came with it at the moment?
Actually I bought the HTC in Taiwan (CHT is the brand on the front) in a shop. At the beginning there was a chinese OS and the seller in the shop changed it to the english version.
I just ran the hard-spl ruuwrapper.exe on my computer with out my phone connected this gave me the 260 error so it is most probably something to do with the phone connecting whilst in boot loader mode, did you click yes to run any program that it asked you to on the phone?
yes, it appered enterBL.exe on my mobile. Then I answered with Y.
I did read some where that resetting the pc might work but i dont know whether it will make a difference considering you've already tried it on another computer.
yes, on my laptop (windows xp). The same problem -->error 260. There is only one difference between my desktop and my laptop. activsync (with windows xp) drops during using the program RUUWraper which WMDC 6.1 (with vista) does not.
Good luck
Click to expand...
Click to collapse
i dont really know what to suggest, what happened when you tried flashing it using the sd card method?
Tried already. Not working too.
program starts not automatically with .nbh file from the SD card when I went into bootloader.
you could try the sd card method again, following the instructions Here to the letter and see how it goes because that should bypass the problem of it not connecting and should work.
Scotty93 said:
you could try the sd card method again, following the instructions Here to the letter and see how it goes because that should bypass the problem of it not connecting and should work.
Click to expand...
Click to collapse
I tried again to flash via SD card but my mobile does not recognize the .nbh file. The mobile stays in bootloader mode and does nothing.
Edit :
maybe I made something wrong ? I used the .nbh file from the Hard-SPL. Is this ok ?
i have attached the .nbh file from hard-spl. renamed to what it is needed to be to work. reformat the memory card so that it is blank and in fat32 format, put this file on it and follow the rest of the steps.
Scotty93 said:
i have attached the .nbh file from hard-spl. renamed to what it is needed to be to work. reformat the memory card so that it is blank and in fat32 format, put this file on it and follow the rest of the steps.
Click to expand...
Click to collapse
Thanks. My SD card is already formatted with FAT32. Is it really necessary to format it again ? I deleted only the files on the SD card and tried it already but it did not work.
If yes to format FAT32 again, do you have also a program for FAT32 formating which is running on vista ?
I downloaded fat32format already but I have to find an adapter to put it into the PC to format. Or is there another possibility to format ?
From the PC I did not find a possibility to access to format directly on my mobile.
there is a formatter on vista but the memory card would have to be connected to the pc, when i brought my micro sd card it came with an adapter to an sd card so i can use it in a usb card reader or the one on the front of my tower.
other wise i dont know if you can format it this way whilst it is connected to the phone.
Scotty93 said:
there is a formatter on vista but the memory card would have to be connected to the pc, when i brought my micro sd card it came with an adapter to an sd card so i can use it in a usb card reader or the one on the front of my tower.
other wise i dont know if you can format it this way whilst it is connected to the phone.
Click to expand...
Click to collapse
Ok thanks. I have to buy an adapter. Then try again.
ye im afraid so i cant think of any other ways that might get your device to flash, you could always wait to see if one of the more senior members replies although you may have to wait until tomorrow.
I am hoping someone could answer this question since nobody has never asked before. I bought a Kingston 32GB micro sdhc card. The model number is SD-C02G made in Taiwan. When I popped in the card into the tablet, it says the card is damaged, formatting is needed. I tried to click on the format button and nothing happened. But, when I test the card on other devices (cell phone & camera & computer), it had no problems at all. No formatting or anything was needed. Does anyone have the same problem or know how to get this fixed?
I am running vegan tab 5.1.1 by the way.
Thanks a lot!
trojanhacker said:
I am hoping someone could answer this question since nobody has never asked before. I bought a Kingston 32GB micro sdhc card. The model number is SD-C02G made in Taiwan. When I popped in the card into the tablet, it says the card is damaged, formatting is needed. I tried to click on the format button and nothing happened. But, when I test the card on other devices (cell phone & camera & computer), it had no problems at all. No formatting or anything was needed. Does anyone have the same problem or know how to get this fixed?
I am running vegan tab 5.1.1 by the way.
Thanks a lot!
Click to expand...
Click to collapse
did you try to format using ur PC in Fat32?
nvm...problem is fixed now. i found out that the memory card was loose probably. Didnt come into full contact with all the pins. Thank you for your reply anyway.
I had the same issue with my new 16 gig card, I let the gtab format it, then rebooted with the card installed, have had no issues for 2 weeks now, card is full of movies and everything works like a champ!
Ok got my sandisk 32GB card from Amazon. I put it in the Gtab but couldn't format the card. Put it on my mac and saw it wasn't formatted at all so I formatted it. No go on the Gtab again... said I need to reformat but the Gtab wouldn't do it. I tried windows to format Fat32 with fast off but kept crashing during format (only showed 27Gb BTW). Searched around and came across windows based program from Panasonic/official micro sd standards site (sdformatter V3). Ran this program selecting all wipe options. The program took 5 days! Successfully finished this morning with correct fat32 so I thought all was well connected to both mac and windows I cant get files to transfer onto the card. I set up a couple media folders but once I start the file transfer it will give me error: improper disk ejection and still show folders. On windows I can get a few files to the card before I get ether "file is corrupt" or I can see that the transfer has stopped and I can see its lost connection between windows and SD card. Did I get a bad card or is there anything I can try here? BTW after that long and painful format Gtab could recognize the SD and I could see the folders I was able to make on the card.
Update:
Now a pop up window for fixing the card has come up on windows once I connected the card reader. I checked the 2 options "Auto fix file system errors" and "scan for and attempt recovery of bad sectors" has been running for 10min and progress bar is half way. hope it fix my problem!
kraftweksfit,
The 32 gig cards have worked back to the beginning as far as I have ever heard.
My opinion, but if it were my card I would return it and ask for one that is not defective.
When you get a good one, make sure it is formatted (on your PC) to FAT32. I also
have found the USB port and card slot are not plug and play like Windows. I
always change them while the G-Tablet is off to all it to search and find them on startup.
Rev
Thanks for that info. I had to shut everything down as my workday was over so now after those 2 windows fixes ran I'm just getting everything back up now at home. So Ive got multiple 2GB movie files to transfer. I still get the random "explorer is not responding" freeze issue on file transfers though. Should I just keep reformatting the card to see if it will fix the issue? Or give up on it and wipe and send it back?
trojan, I've got a question. have you tried putting more than 2 gb on the card? I can't seem to find a 32 gb version of the SD-C02G. Also have you done any speed tests on it?
kraftwerksfit said:
Ok got my sandisk 32GB card from Amazon. I put it in the Gtab but couldn't format the card. Put it on my mac and saw it wasn't formatted at all so I formatted it. No go on the Gtab again... said I need to reformat but the Gtab wouldn't do it. I tried windows to format Fat32 with fast off but kept crashing during format (only showed 27Gb BTW). Searched around and came across windows based program from Panasonic/official micro sd standards site (sdformatter V3). Ran this program selecting all wipe options. The program took 5 days! Successfully finished this morning with correct fat32 so I thought all was well connected to both mac and windows I cant get files to transfer onto the card. I set up a couple media folders but once I start the file transfer it will give me error: improper disk ejection and still show folders. On windows I can get a few files to the card before I get ether "file is corrupt" or I can see that the transfer has stopped and I can see its lost connection between windows and SD card. Did I get a bad card or is there anything I can try here? BTW after that long and painful format Gtab could recognize the SD and I could see the folders I was able to make on the card.
Update:
Now a pop up window for fixing the card has come up on windows once I connected the card reader. I checked the 2 options "Auto fix file system errors" and "scan for and attempt recovery of bad sectors" has been running for 10min and progress bar is half way. hope it fix my problem!
Click to expand...
Click to collapse
That Panasonic tool is a favorite over in headfi-org - I've been using the older version for years and it actually works on a Windows VM. We used to use it on our Cowon D2 to ensure that our SDHC cards were being read properly.
For v2, if you do a quick format it should not take that long.
roebeet said:
That Panasonic tool is a favorite over in headfi-org - I've been using the older version for years and it actually works on a Windows VM. We used to use it on our Cowon D2 to ensure that our SDHC cards were being read properly.
For v2, if you do a quick format it should not take that long.
Click to expand...
Click to collapse
So you think the card just needs to be reformatted again? If so I'll try the quick option. When that program took so long I thought for sure something was wrong. BTW all references to windows are on VM on my mac as well.
Should I be worried that my Gtab can't format the card? I'm on Vegan 5.1
thanks
UPDATE:So I ran the quick option of SDformat V3 with no problems, was able to transfer one 2GB movie no problem. I went to try to move more files and instantly the progress bar for transfer does not move, "more details" tab shows est. time calculating... so my guess is windows explorer lost connection with the card. also every time I eject the card/reader windows want to fix errors which I've already run so I think this card is dead!
Bad SanDisk is on it way back, after browsing amazon I came across a Kingston 32GB micro sd with adapter class 4 for 39.99 + shipping. I went for the store front offering for 41.99 + 9.98 shipping. Best price I can find for a quality card if anyone is looking for one. http://www.amazon.com/gp/product/B004QQKI0G
I recently upgraded my memory card on my Streak to a 32gb class 10.
When trying to put files (pictures and videos) on the card via the USB cable the files appear to have been copied okay, but when trying to access the files on the Streak they are either missing or corrupted.
I reformatted the card in the Streak and tried again. This had the same effect.
I transferred some files via skydrive and they worked fine. But the next time a accessed the card via USB, the files disappeared again, even though I didn't access the folder in question.
This is the second card I have tried, so I assume that the card is not the problem.
I'm running stock 2.2.
Any help would be greatly appreciated.
What OS are you using?
Even though the file copy may appear complete it may not be. Make sure you use whatever steps are appropriate for your OS to eject or unmount the SD card after copying.
Using Win 7 x64...
I'll have another go and let you know.
Sent from my Dell Streak using XDA App
I've tried again making sure that I've selected Turn off USB storage from the handset and safely eject from the PC. It still happens.
The strange thing is that it even affects folders that I didn't access whilst connected to the PC (it either empties or deletes the folders).
Totally stumped on this. Could it be a problem with the card? If so, has anyone used a 32gb card that works that they can recommend?
You have tried at least 2 cards, but have you tried a different PC. Is it possible you may have "something" running on the PC causing this.
sketch-UK said:
I've tried again making sure that I've selected Turn off USB storage from the handset and safely eject from the PC. It still happens.
. . . .
Click to expand...
Click to collapse
Make sure that you do those in the correct order. Safely remove from PC first, then turn off USB storage on the phone.
If you can read the card with no problems make a backup and then format the card in the phone. I have seen a lot of cases (and not just with Streaks) where issues were caused by using a card that had not been formatted while in the phone.
Where did you buy the card from? I ask because this sounds a lot like the symptoms you see with faked cards that are really much smaller than the 32GB they claim.
jim-bo said:
Where did you buy the card from? I ask because this sounds a lot like the symptoms you see with faked cards that are really much smaller than the 32GB they claim.
Click to expand...
Click to collapse
Hmm. I got it from Ebay. It does show as 31.2gb in windows.
This is the second card I've had from this supplier (I sent the first back because of the problems with the streak as listed above). As I had the same probs with the 2nd card I assumed the device must be at fault.
Are you sure the card is legit? you should hook it up to a card reader and loading +20gb of data and seeing if it's good
I tried transferring a load of files to the card and it stopped after about 3gb. Some of the folders were empty.
I tried reformatting in windows and noticed it was FAT32. The card will not format as NTFS.
I guess this means that the card is duff?
it definitely sounds like you got a fake, those are classic signs it's a fake
Hello,
i have a brand Vodafone IT Titan with:
OS: 7.10.8107.79
firmware: 166.2200.20501.165
radio: 16.23.06.10_16.32.00.23U
bootloader: 2.5.160015.3(137079)
i wanted to upload the 2.05 eu rom so i have downloaded this rom: http://www.filefactory.com/file/1ybq4xqcazyp/n/IMG_Eternity_HTC_Europe_2.05.401 and obtained the file named 'IMG_Eternity_HTC_Europe_2.05.401.01_Radio_Signed_16.23.06.10_16.32.00.23_ETERNITY_RELEASE.nbh' (yes it has the apex included in the file, vary strange for me) that is 419.982 KB
i have renamed the file in ETERIMG.nbh.
i have downloaded goldcardtool and goldcard.img.
i have formatted the microSD in fat32.
i have copied ETERIMg.nbh in the microSD.
i have patched the microSD with goldcardtool and goldcard.img
i have connected the Y usb cable to the Titan, the microSD card reader and the PC.
i have booted the Titan in USB HOST mode but it always show me "Entering USB Mode". Upload does not begin at all.
So, what am i doing wrong ???
Please guys help me!!!!
nyonik said:
i have renamed the file in ETERIMG.nbh.
i have downloaded goldcardtool and goldcard.img.
i have formatted the microSD in fat32.
i have copied ETERIMg.nbh in the microSD.
i have patched the microSD with goldcardtool and goldcard.img
i have connected the Y usb cable to the Titan, the microSD card reader and the PC.
i have booted the Titan in USB HOST mode but it always show me "Entering USB Mode". Upload does not begin at all.
So, what am i doing wrong ???
Please guys help me!!!!
Click to expand...
Click to collapse
Looks likes that your Y cable is fine, with your phone showing "entering usb mode". This leaves your gold card as possibly the main culprit. In other threads, some had the same issue and managed to flash their phone by trying other type of microsd card and card reader. I used a kingston 2gb microsd card and multicard reader. I managed to debrand my att titan to european 2.05 rom (see the thread I started on this topic: http://forum.xda-developers.com/showthread.php?t=1693334&page=2)
Thanks for the replay.
I don't know if the cable is ok. I bought it on ebay:
http://www.ebay.it/itm/260747604735?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
It is a normal Y cable used for external HardDisk when a single usb port is not enought for powering the device.
I connected the miniUSB port to my card reader.
I connected the dataUSB port to my phone (using a famale-famale adapter)
I connected the powerUSB port to my pc.
The strange thing is that when i plug the phone (phone is already turned on)
then the phone fell i had connecet it and the led become red.
Also the led on the card reader is Turned on, meaning that it is turned on.
But when i restar the phone and push vol- and camera going in USB Host mode,
the led on the card reader is desapeared, so i thing it is turned off.
The phone is now waiting in USB Host mode.
So i disconnect and reconnect the power usb cablo form the pc, and so the card reader turned on again. But the upload does not begin.
Do you thing that there is something strange ?
may be i miss something on doing the gold card (wrong image, wrong name) or samething like that?
I have already tried with 4 different memory card but (512MB MMC, 1GB microSD, 8 GB microSD and 1GB SD card) the result is the same.
I have a question, after downloading the
'IMG_Eternity_HTC_Europe_2.05.401.01_Radio_Signed_16.23.06.10_16.32.00.23_ETERNITY_RELEASE.nbh'
file
I have to extract RUU_Sigbned.nbh and rename it in ETERIMG.NBH
or jusy keep the whole file and rename it in ETERIMG.NBH ???
If i have to exctract RUU_Signed, how can i do that??
I have the same question as nyonik.
After getting to the USB Mode, I plug in the phone the card reader turns on and off and it goes straight back to ther SPL screen and freezes there. When I unplug the device the word "serial" appears on the screen. I've havent been able to find someone on here describing a similiar scenerio. I've tried several different types of media and they all do the same thing.
@nyonik- you copy the euro rom 2.05 to microsdcard rename it to ETERIMG.nbh then make it a goldcard.
@jonesk001- that also happened to me, what u need to do when it goes back to spl mode, unplugged phone "serial" appears, then restart phone by pressing power button for few secs when it start to boot hold down vol- and camera buttons this will boot ur phone to "usb mode" screen, at this point plug it back to Y cable. Your phone should proceed with flashing. If it again kick back to spl mode repeat the steps i described. Goodluck.
Sent from my TITAN X310e using XDA Windows Phone 7 App
Thanks Habnzrot for tips. Finally got everything to work. Amazing enough I used WinXP to format and make the gold card instead on Win7 and it worked, using the same setup that was previously didn't work.
jonesk001 said:
Thanks Habnzrot for tips. Finally got everything to work. Amazing enough I used WinXP to format and make the gold card instead on Win7 and it worked, using the same setup that was previously didn't work.
Click to expand...
Click to collapse
Good to hear that you now managed to flash your phone Enjoy custom rom (s)!
use 1gb msd card. before I used a 4gb card it has the same issue.
Hi, I usually dont write, but I read a lot here.
about 2 weeks ago i bought my S3, and everything was great. about 2 days ago I bought a 32GB MicroSD card (Sandisk Ultra Mobile CL10)
and put it into the phone, when I try to connect it to the computer via the USB cable, the transfer rate is extremely slow!!!
It usually just freeze about the middle and just pop-out a message that "The File could not be copied", and its the same to every file I try (regardless the type/size etc).
the strange thing is that it does the same to the internal memory!
if I take out the the MicroSD and put it into a card-reader and into a the computer it works great and transfer rate is about 20Mb/s!
is there anything I can/should do?
I know that on my old Motorola I could plug it into the computer and the SD card was shown as a "Removable Disk" and I could just copy and paste, and the S3 is either shown by a Camera or a media device... is there a way to make it as a Removable Disk?
I'm with a stock rom is that's matter.
hope I could get your help.
Thanks.
Xebu said:
Hi, I usually dont write, but I read a lot here.
about 2 weeks ago i bought my S3, and everything was great. about 2 days ago I bought a 32GB MicroSD card (Sandisk Ultra Mobile CL10)
and put it into the phone, when I try to connect it to the computer via the USB cable, the transfer rate is extremely slow!!!
It usually just freeze about the middle and just pop-out a message that "The File could not be copied", and its the same to every file I try (regardless the type/size etc).
the strange thing is that it does the same to the internal memory!
if I take out the the MicroSD and put it into a card-reader and into a the computer it works great and transfer rate is about 20Mb/s!
is there anything I can/should do?
I know that on my old Motorola I could plug it into the computer and the SD card was shown as a "Removable Disk" and I could just copy and paste, and the S3 is either shown by a Camera or a media device... is there a way to make it as a Removable Disk?
I'm with a stock rom is that's matter.
hope I could get your help.
Thanks.
Click to expand...
Click to collapse
Sound like a problem i had when i got my 32gb card. for me it turned out that i had to change the usb port as the one i was using decided to be a usb1.0 port, changed port, installed drivers for a different port and it fixed my issue, dunno if it will work for you but worth a try.
also try formatting your card.
joey jojo said:
Sound like a problem i had when i got my 32gb card. for me it turned out that i had to change the usb port as the one i was using decided to be a usb1.0 port, changed port, installed drivers for a different port and it fixed my issue, dunno if it will work for you but worth a try.
also try formatting your card.
Click to expand...
Click to collapse
I just tried on another computer, the problem didn't occur but the transfer rate is still VERY slow...
I format the card within the phone and when I looked on the properties of the MicroSD card, under File System is written "generic hierarchical" - is that normal? is there anyway i could format it to NTFS or even FAT32? the phone will still recogsize it if i do?
Xebu said:
I just tried on another computer, the problem didn't occur but the transfer rate is still VERY slow...
I format the card within the phone and when I looked on the properties of the MicroSD card, under File System is written "generic hierarchical" - is that normal? is there anyway i could format it to NTFS or even FAT32? the phone will still recogsize it if i do?
Click to expand...
Click to collapse
Thats what mine says too, not sure which format it uses by default.
I have heard that you can format to ntfs or fat32, but i havent tried it, too scared to damage it and loose 32gb from my phone accidently, lol (ive done this before. ) but search and see.