Hi all,
For some reason my car charger has fried the USB port on my M3100 so I can no longer charge or sync it. Orange are sending a replacement out tomorrow, but I had just upgraded the phone to the new HTC Rom. Obviously I need to get it back to being the Orange one.
As I can't do it via USB I am trying to flash the Orange ROM on using the SD method. However, when the phone resets after PWR+OK+SoftReset all I get is the tricolour screen with the following on it:
HERM100
IPL-1.01
HERM100
SPL-1.40.Olpro
Serial
I've extracted the .nbh file from the Orange .exe and have formatted my SD card as both FAT & FAT32 in Vista but with no luck. Any ideas?
Thanks in advance folks,
Bobby
Rename the .NBH file to HERMIMG.nbh and copy it to the root folder of your microSD card. Make sure there is NOTHING else on the card.
I've formatted the card twice and put just the renamed HERMIMG.nbh file on it but it still doesn't work. I've never had a problem with the SD slot, or the card, so I don't think it could be that.
Funny, but i remember that it did not work here too... Flash just did not start at all, even if there was HERMIMG.nbh, and it was the only file on the card... Tried both FAT32 and FAT too. Funny. It was in the case of X01HT 1.09 original bootloader, if I remember right...
Did you have any luck getting it to work? Or is it looking like I should have an unfortunate accident with some h2o before they come for it?
try doing the same with SSPL if you can't get it to work from bootloader, or try using another microSD card. Or try resetting a few times... but don't throw h2o on it!
I can't get anything to work via the miniUSB port so nothing that runs on the PC will help. I've just noticed that the tricolour screen comes on, then for a fraction of a second the screen goes grey with 'Loading No Image Found' then back to the tricolour.
The only other SD I can get my hands on is the same make as mine, so I doubt it would make any difference. And I've reset it loads of times while doing this but still nothing. I've tried sticking another nbh file on the card to see if it was just the Orange one it couldn't see, but a radio only one still didn't work.
It had all been going so well...
Hold on, I might have cracked it...
Nope, not yet. It gets as far as showing EXTROM - OK and the progress bar gets about a quarter of the way along then it seems to lock up. The bar hadn't moved for well over 10 mins, so I've soft reset it. Its has the first Orange splash screen now, but the rest is still the HTC ROM. Its a start I suppose.
Hurrah! Rejoice! Its worked, and is back to the slow old crippled Orange ROM. Thanks for your help folks, much appriciated.
Roll on tomorrow night when I get to update my new one all over again!
bigpapalove said:
Hurrah! Rejoice! Its worked, and is back to the slow old crippled Orange ROM. Thanks for your help folks, much appriciated.
Roll on tomorrow night when I get to update my new one all over again!
Click to expand...
Click to collapse
Good thing you documented what worked for you so that others can benefit too.......
Hi, I`m having some serious issues when trying to flash my HERMES. As far as I can tell, it is SIM Unlocked, but not sure if it`s CID unlocked. it`s SPL-1.06, and I can't seem to get it to install HARDSPL. I have tried, and tried and tried and tried. I've tried flashing VIA SD-CARD, but it just says "LOADING" and displays a number at the top, then goes back to the bootloader screen.
When I am flashing via the wizard, it'll go into the bootloader screen, and the wizard will fail saying it cannot connect "CONNECTION ERROR"...
I am at my wits ends, and cannot figure this out for the life of me. I have had 3 TYTN's now, and this one has gotten the better of me. I was able to flash both of my other TYTN's, but unfortunately I got the WSD, and cannot repair them, they are both beyond my technical knowledge of repairs...
PLEASE PLEASE PLEASE PLEASE PLEASE help....
Trying so hard to get this done...
Copied the .nbh (ren to hermimg.nbh) to my SDCARD and reset into bootloader, as I said, it just came up "LOADING" then back to bootloader....
I'd rip my hair out if I had any..
any help would be appreciated..
***UPDATE - I don't know what the hell happened, but suddenly, this bugger is letting me flash VIA SD. It's a damned miracle!
Just out of the blue, it asked me to flash via SD in the bootloader. Thank goodness! After 3 hours, I finally got it working..
Cheers all!
if you need more info, just ask, I will provide all I can....
need help ,during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
IPL 1.01
SPL 2.03
my device freezed at loading screen .
Now ,when i tried to rom upgrade in bootloader mode , using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
Edit/Delete Message
TVincent0621 said:
need help ,during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
IPL 1.01
SPL 2.03
my device freezed at loading screen .
Now ,when i tried to rom upgrade in bootloader mode , using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
Edit/Delete Message
Click to expand...
Click to collapse
Okay, when you're in the "bootloader" method, have you renamed the file that you're trying to flash "HERMIMG.NBH".
also, try to use the "stripped" AT&T ROM first, see if that'll help correct the issue.
Did you flash that first before you attempted to flash a different ROM on your Hermes? I've read in many different posts that it is highly suggested to flash that first then flash your ROM to your Hermes.
Should always flash via SD-Card, not recommending flashing via USB Wizard.
Try the "stripped" rom first, on a formatted (FAT32) microSD card, and see if that helps.
Cheers
i have download the "stripped" AT&T ROM ,it also the same ,when using USB method ,it stuck at 1% and my devide reboot .
when using SD card method ,it show (loading ...) about 2 second ,then it will back to tri-color mode there .
TVincent0621 said:
i have download the "stripped" AT&T ROM ,it also the same ,when using USB method ,it stuck at 1% and my devide reboot .
when using SD card method ,it show (loading ...) about 2 second ,then it will back to tri-color mode there .
Click to expand...
Click to collapse
I had that exact same problem.
I noticed that I hadn't named the file properly.
It's HERMIMG.NBH I kept putting in HERMING.NBH. It's kind of funny, but it's an easy mistake. When you boot with the "HERMIMG.NBH" it should flash. I used the HARDSPL V7, which can be downloaded at http://forum.xda-developers.com/showthread.php?t=296722, which is a "sticky" for this forum. Try flashing that one. Also, double check your .nbh file, make sure it's HERM IMG not HERM ING
That was the problem I was having too, it would just show "LOADING" and a bunch of numbers then drop to the bootloader... Then all of a sudden... "POOF" it worked, after I double checked the file and noticed my spelling error.
Now, if you have that fixed and still getting the error, it might be something else. I'm not sure how to exactly fix that, but as I said, mine was just a minor spelling error.. The exact spelling that I have, don't know if it is case sensitive, is "HERMIMG.nbh"
if it is case sensitive, that could also be a minor issue.
try it, if it works, then bingo, you're back in business, if not, then I'm not sure how else to fix it.
Cheers!
>.< ,now i type correct word "HERMIMG" ,it shown loading ... and (00068002) on the top of loading ... ,now it ,have better improvement ,it show loading ... for about 5 second only jump back to tri-color there ,izit this is the normal procedure ?
TVincent0621 said:
>.< ,now i type correct word "HERMIMG" ,it shown loading ... and (00068002) on the top of loading ... ,now it ,have better improvement ,it show loading ... for about 5 second only jump back to tri-color there ,izit this is the normal procedure ?
Click to expand...
Click to collapse
Okay, we're getting there. But still a long way off from it working as it should.
Okay, do you know if your phone is HARDSPL?
If you haven't already HARDSPL your phone, you should download that and try to flash that onto your phone.
Also sounds like it isn't SUPERCID. You'll have to CID unlock your phone, which is a good possibility as to why it isn't accepting other ROMS.
If your phone responds to the flash wizard when you download a ROM then get the SUPERCID and try to flash that one first, then move on to the HARDSPL.
For the SUPERCID, and my previous post has the HARDSPL.
At least the situation is improving, and your phone is starting to respond.
We'll get it working!
The HARDSPL you have to follow most of the "manual" installation instructions, and copy, then rename the "HermesUnlocker_v3a.nbh" file.
Try to flash that file, and we'll see if we can get it going.
Cheers
i think my phone not yet HARDSPL ,can you guide me to do this ?
i search the web ,it show me to here "http://forum.xda-developers.com/showthread.php?t=296722" izit correct ?
and also superCiD:
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button.
how i wana do the step 6 ,my phone is stuck now ,i cant log in at all >< ,but i try step 1-5 ,it also shown the 00068002
TVincent0621 said:
i think my phone not yet HARDSPL ,can you guide me to do this ?
i search the web ,it show me to here "http://forum.xda-developers.com/showthread.php?t=296722" izit correct ?
and also superCiD:
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button.
how i wana do the step 6 ,my phone is stuck now ,i cant log in at all >< ,but i try step 1-5 ,it also shown the 00068002
Click to expand...
Click to collapse
Attached is the HARDSPL file, already named "HERMIMG.nbh, which you just need to copy onto your SD-CARD.
When those are successful you will be able to flash any rom you want (provided it is as Hermes ROM)....
But as of right now, your phone is NOT bricked. It just currently has no ROM on it.
Have you tried to HARD-RESET your phone?
That's the two soft keys at the bottom of the phone, above the SEND and about the END keys.
Press and hold BOTH of those, then press the "RESET" button on the bottom of the phone. That'll hard-reset the phone.
I'm not saying to do that, just asking if you've tried that option yet.
Good luck, let me know how it's going.
Cheers!
my problem has solve now ,i try to install original rom for the phone ,it work ^^ ,thank for your help ,nice to meet you my friend from oversea .
Now i afraid to change any new rom >.<,can you guide me the best way to upgrade the rom ?so that i wont face the same problem and also brick my phone .
TVincent0621 said:
my problem has solve now ,i try to install original rom for the phone ,it work ^^ ,thank for your help ,nice to meet you my friend from oversea .
Now i afraid to change any new rom >.<,can you guide me the best way to upgrade the rom ?so that i wont face the same problem and also brick my phone .
Click to expand...
Click to collapse
Glad the problem was solved, and very happy to help!
Absolutely I can.
First thing is first, we have to SUPERCID unlock your phone, and we have to HARDSPL your phone.
Run the HARDSPL first, because the wizard will actually temporarily superCID your phone, so that you can install the HARDSPL, which will help prevent you from ever bricking your phone.
with your phone plugged in for activesync, you have to run the "autounlocker.bat" file in the SUPERCID. What this will do is make your phone accept other custom ROMS, whether it is from another carrier, or one of the ROMS that someone has developed on here.
After this, I would highly suggest, that if you ever flash your phone again with another ROM, do it the "SD-CARD" way. I'd only use the wizard to flash the HARDSPL and the SUPERCID.
Let me know how it goes.
Cheers!
Hehe ,My friend ,i had flash my phone with WM6.5 rom ,my device was Dopod838pro ,it is old device ,for my opinion WM6.5 not so suitable for my device ,but WM6.5 look amazing >.<
heh! Nice! Well sounds like your phone is now back amongst the living! That's good news! Hope you have many years of enjoyment with your phone!
Glad to have been of help for you!
Cheers
heh! Nice! Well sounds like your phone is now back amongst the living! That's good news! Hope you have many years of enjoyment with your phone!
Glad to have been of help for you!
Cheers
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
TVincent0621 said:
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
Click to expand...
Click to collapse
Unfortunately, no, I don't. You'd have to get a Vanilla, or a "lite/ultralite" rom. That's about the best I can suggest, unfortunately with the hermes, it does have a smaller ROM size, and limited RAM compared to the new, more up-to-date modern phones, like the 8925(Kaiser), or the new Tilt 2..
Cheers
TVincent0621 said:
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
Click to expand...
Click to collapse
Unfortunately, no, I don't. You'd have to get a Vanilla, or a "lite/ultralite" rom. That's about the best I can suggest, unfortunately with the hermes, it does have a smaller ROM size, and limited RAM compared to the new, more up-to-date modern phones, like the 8925(Kaiser), or the new Tilt 2..
Cheers
use the [Easy Hard-Spl v7 beta v0.1] by qwasde2
it,s really usefull i tryed it,s by me
it,s for win XP and vista and se7en users
i,am not joking here is the link
http://forum.xda-developers.com/showthread.php?p=5136858#post5136858
Hope you dont mind me reviving this thread as I also need your help
I tried flashing the MrDSL's WM6.5 ROM to my Hermes. Of course I followed the direction, I have Hard SPL (ever since Schaps rom) and stripped ATT flashed first.
However when I started flashing this rom, when I reached about 5% on the progress bar, I keep on getting Error. I followed the Recovery Steps and luckily I get the Tri-color mode and the process says Recovery successful. I then proceeded with the flashing but still getting errors, then recovery, then continue, then error again. Its been 10th try now.
Finally I canceled the update but I can only get the tri-color screen. Tried to Softreset as well as Hardreset but no go....my screen only gives me the Tri-color mode.
Any advice please....
thank you very much...
EDIT.....
problem solved sorry for that post.
what I did was:
1. flashed again the stripped ATT ROM....success!
2. flashed again MrDSL's WM6.5 titanium ROM (titanium)....success!
Dopod 838 Pro working again!
thanks again!!!
Bootloader shows but phone won't flash
Hey everyone,
I'm not new to
flashing my Hermes.
I'm just having an
issue I've never ran
into and can't figure
out. I would
appreciate some
assistance.
The strangest thing
is happening to me
while attempting to
flash from my
storage card. I put
the phone in
bootloader mode
and it takes
(IPL-1.04 /
SPL-2.10.olipro).
Then on the bottom
Serial shows and it
never goes to the
next step and ask
me do I want to
flash the new image.
I put the att original
on the 2gb storage
card over and over
and over and
renamed it
HERMIMG.nbh over
and over and over
and just am
flabbergasted. The
phone is not bricked,
it just refuses to
flash again.
Does anyone here
have any solutions
or suggestions?
PS - I have
formatted the card
to fat32 and I have
checked it for errors.
The HERMIMG.nbh
file is on the root of
the storage card.