Think i knackered my screen - MDA, XDA, 1010 General

Right, i'd appreciate any help you guys can give me, especially if it means i don't have to spend money.
My XDA fell about a foot off my bved onto a capeted room, it's fine but now there's a line going straight down the middle of it. then the screen flickers and the whole right of the screen is covered with vertical lines then it goes back to being just the one line in the middle.
Now i'm guessing that a new screen would sort that out instantly but say i didn't have £150.20 lying around, anyone got any suggestions?
Thanks loads guys

small suggestion
my two cents worth:
all LCDs are connected by some sort of ribbon connector to the main board of a unit, my experience with nokia celphones INDICATES that some lines in the LCD do not display due to LOOSE connection between the ribbon connector to the mainboard. Sometimes, we just replace the ribbon and even just push it to the board a little and this seems to solve the problem.
My suggestion to you would be: There is a site that i've seen that sells replacement LCD and glass covers, and its a DO-IT-YOURSELF kit, so get info on how to OPEN your XDA, if youre not fainthearted, then apply a little pressure on the ribbon connection to the mainboard, this may help. OTHERWISE, if you are not a TECHIE, have a service center check that for you, YOU MAY NOT HAVE TO REPLACE THE LCD anyway.

Nice, you wouldn't have te address for the place that sells the screens would you?
Ta

It may be that you have dislodged the cable connecter or the contact connection to the screen, many nokias displayed this same fault and sold millions of screens when all that was needed was either to attend to the connections or remove the elastomer and reverse it, or replace the elastomer. An elastomer is a small rubber block with a row of connecters either side, this is the bridge for the electrical/video lines to the screen. Its worth a look anyway to see if anything obvious has occured.

try searching "Repacement LCD Screens", you might find the shop that sells them, its in a thread here somewehere.
The latest suggestion and mine are almost identical, YES, it may really be the ribbon connector that was PARTIALLY dislodge or looses contact sometime.
Search and ye shall find. hehehe. goood luck. Tell me when you find it and POST the thread here will you, for others with the same problem as you to be helped.

website
OH, heres the website.
http://www.pdasmart.com/pdaphone.htm

thanks, i'm really glad to hear it's probably just the cable, but now the problem is finding the right screwdrivers

lol, seriously i haven't got any screwdrivers the size to open my XDA, and i don't particularly want to send it off to a repair centre, they'd charge me for labour, anyone got any ideas?

You need a t6 torx driver and a flat blade dirver and a small crosshead driver.

Anyone Got a t6 torx driver? because i know i haven't lol. how many people do you reckon would have one?

UPDATE
evening all, just got me T6 screwdriver, i opened my XDA and found what looked like te connector and had a bit of trail and error but it still doesn't completely fix it, any ideas?[/code]

Related

Some help for a newbie... [broken screen]

First of I would like to say thanks to this forum.
I try not to post any problems that have already been answered and this forum was a big help in getting my xda unlocked.
However I had only had my phone in working condition for 2 weeks, enough time to start to like it, when it fell and cracked.
I ordered a new glass screen (no bleeding ink) and had it overnighted. I sucessfully swapped out the broken scree, but in the process I screwed up the phone. So here is whats going on with it, if anyone can help me out it would be awesome.
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Sorry for the long winded post
Thanks for the help
Chris
Also if this cant be fixed whats my best option, selling it broken or parting it out? How much could i get?
Re: Some help for a newbie... [borken screen]
beggy said:
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Click to expand...
Click to collapse
Well, I guess it depends on how broken the connectors are, but this definitely doesn't sound good...
If you post a few close-up pictures, I'll tell you if there's any hope for fixing it.
Well..
One of those 3 connectors lead to the screen.
My wild guess would be that it's not porperly connected since it's borken.
In that case, I would have done one of two things:
1. Buy a connector through an electronics component vendor, then ,manually replace the broken one or have a electronics lab do it for me.
2. Solder the wires to the connector's base manually (or in a lab) to over-ride it. (I hope you understand what I mean).
At any case, my guess would be a broken connection somewhere in the connectors (one of the 3). This can probably be fixed that way or another.
BTW - I have a lot of dust between the glass and the screen. How do you remove the glass from the screen (it seems to be attached firmly somehow)??
To take the glass apart from the lcd, there are 4 metal tabs (2 at the top and 2 on the bottom) you can pry a thin flat-head screwdriver between the metal tabs (you will see what I am talking about, when you look closer). It will sound bad but its just the glue coming apart.
I tried to get the connectors but had no luck finding a match.
So I am going to part out the phone.
Ill be posting the ebay auctions for the lcd screen, the new glass piece, the motherboard, the battery/case and whatever misc accesories I have lying around.
Before I put all the parts on ebay, I figured I would give the people on here a crack at it. I will entertain all reasonable offers. Send me a PM.
Here is what I have for sale
Case in good condition w/ battery
Motherboard - in good condition just missing the two plastic pieces where the lcd connects.
Brand new glass touchscreen/digitizer
Lcd Screen
Also for sale the in-wall charger, the sync cradle with an extra 3 stylus (styli?).

HTC Topaz disassembly guide

Hi, is there any chance to get Topaz disassembly guide?
THX
Edit: Dont need it anymore, I have done it, not difficult at all (similar to Nokia phones). HTC made Topaz very easy to disassembly.
I was cleaning part between digitizer and LCD from dust with antistaic brush and compressed air.
There are just 3 connectors to disconnect mainboard (digitizer, phone receiver and LCD), to get to the LCD. No coaxial cables to connect GPS and bluetooth antenna (all just by touch connectors to the black plastic top back part), Chipset is covered by metal plate, cant see it.
LCD: S/N: 1EJV093Q000069
P/N: 60H00209-00M S508
Can I request you get some high res photos of the PCB/LCD and/or record the ic part numbers while you've got it apart? It would be really useful to know for Linux/Android development.
Can you post what kind of gps chipset is buildin ?
Thanks in advance
Daniel
Thanks for the photos! Would you be able to post a higher res version of the 3rd one or simply scribe what is written on the back of the LCD. I'm hoping the serial number might give an indication of the chipset used in the LCD.
cheers!tsy
So you can sure tell us if the front frame is really metal or plastic ?
Its metal body iside of plastic housing.
Great job !
Thanx
some instructions or tips of how you disassembled it would be nice
i unscrewed my diamond2, and i cannot find a way to disassemble it..
help!
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
i found a htc service manual for diamond 2 that was leaked
not sure if i can post it here..
it explains how to disassemble the device
EDIT: I am so sorry, the leaked document is the user manual, it is incorrectly posted as the service manual in many sites. sorry
post it! what's the worst they can do... tell you to remove it?
PhilipL said:
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
Click to expand...
Click to collapse
Look here:
http://forum.xda-developers.com/showthread.php?t=520795&highlight=solution%21%21%21
Sticky? New Thread? & Help
I think we either need to sticky this, or make a new thread that encompasses all disassembly / dust leak information about the topaz.
I still cannot disassemble my device, i wish someone could help :/
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Guinea.Pig said:
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Click to expand...
Click to collapse
Thanks for the steps. I just yesterday disassembled my TD2, but didn't dare remove the connections on the mainboard. The one on top left (see your pic mainboard.jpg) is no issue, but the other ones are tricky...or at least I thought they are. I couldn't figure out how to exactly remove those connectors. Could you maybe give some steps or info on how to remove those connectors? Thanks again for your help.
disassembly
thanks for the update . ill try and post pictures up when possible.
I am interested in this too, I have dropped mine a couple of times and am looking to replace the housing (although I have already been ripped off once by buying a repaired one on ebay).
So any idea where I can get a legitimate full housing and a guide to moving the guts from one to another?
Cheers,
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Awesome
stormyuk said:
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Click to expand...
Click to collapse
Thanks for your contribution stormyuk !
You can find housings on ebay, though most don't come with the buttons.
I bought one and its practically impossible to distinguish any differences,
Buy from kr-net on ebay its the seller that sold me my housing

Replacement keyboard for G1 (take 2)

Before we were so rudely interrupted in the original thread, we were discussing the G1 hardware keyboard replacements. Please folks, if you must flame each other do it via PMs to avoid locking legitimate threads.
I've been able to find some inexpensive after market replacements on eBay, but still am not sure how difficult it is to actually do that. All the sites I've been able to find on the subject only provide time-lapse dis-assembly instructions of the entire phone. If anyone has done the replacement themselves, I'd greatly appreciate pointers on how to keep my phone operational after I put it back together.
I replaced the white keyboard in my Dream with a black one. It was a scary operation as it takes a bit of force to dismantle. I accidently pulled my antenna off and disconnected a flylead. ment my phone had no signal at all. later when i got home (did it in work ) i took it apart again and fixed it.
Take your time and have patience, alot of it is plastic and clipped together so requires a bit of force.
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
brummiesteven said:
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
Click to expand...
Click to collapse
It's the combination of silver keys with light-silver backlight that make the lettering almost impossible to see in day light conditions. I'd take a picture if I had a camera with me today. Whoever came up with that color combination should be fired. Or at least made to stare at it every day for the next year. I have to tilt the keyboard at a weird angle just to distinguish the letters. From what I understand the white G1s suffer from the same problem.
The "Backlight Off" app definitely helps as it lets you toggle the backlight with a keyboard shortcut. I'm looking for a more hardware solution though.
I've been thinking about changing keyboards and housings too. But from what ppl are saying it seems to be pretty exhaustive. Do any of you guys have the service manual? I DL'ed it from somewhere and it goes through each step of disassembly and also shows assembly. I'm sure it would help out to give an idea of what you need. But like I said, even having read the service manual, it's still quite scary.
A full housing from my understanding is a bitc(....doing the KB I can see why. The LCD portions look ridiculously complex in comparison to other phones.
That said if you have the proper tools , good organization or memory , steady hands and patience really shouldnt be "that" tough to do the keyboard.
Heres the thing. Its really not that hard to unscrew things etc...but the piece you need to move in order to get proper access to the KB has 2 ribbons that are a PAIN IN THE ASS to take off and put back properly. Theres so little room for error.If youve never worked with ribbons before BE CAREFUL.
I will say G1 is pretty unique in how its put together , I swear they were determined to make it as complicated as possible
The really pain in the ass part is that the online manual/guide will merely tell you something like "remove part A" but no explanation how. Theres also 2 screws I swear it glossed over leading to frustration when I did the trackball/front keys.
Torx 5 and really good mini screw driver are mandatory.
Nice lil workstation is really helpful..(masking tape ,towel , table lamp or LED headlamp , vitamin/pill cases etc)
Im no mechanical engineer but Ive opened up damn near everything Ive ever owned at some point. Took me a solid 3 hours from start to finish. With major time spent on organizing the screws pieces and those damn ribbons.
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
KOF33 said:
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
Click to expand...
Click to collapse
Pics, or it didn't happen
Thanks for the tips!
Chahk said:
Pics, or it didn't happen
Thanks for the tips!
Click to expand...
Click to collapse
As you can see I also replaced the trackball with a glowing white one.
lol at the trackball
doing a case swap is only bad the first time LMAO. I learned a lot, like for example the brass inserts that the screws go into...are not pre-installed. You must CUT Them out of the old housing and HAMMER them into the new oneBut in the end, it turned out very nice.
As far as just replacing the keyboard, it isnt too bad actually once you know what screws hold what down!
-Remove the 6 torx screws for the back housing
-GENTLY pry open the TOP of the casing with a plastic case tool, work your way down to the bottom of the housing. The bottom is a PITA to remove. I usually get it by rocking it gently back and forth
-remove the long and short coax leads from the motherboard side. swing them out of the way
-peel back the tape and GENTLY pull the bottom connector (mouthpiece module) from the motherboard.
-peel back more tape and lift the latch for the keyboard connector (the one on the side)
-Peel the camera module up SLOWLY (it is double side taped down) as well as the imei card. The cam cable is routed under it, lift it all as a unit. When you get to the motherboard, STOP
-Now, gently twist the whole camera and motherboard unit as a whole until it is free of the latch on the side. Gently lift the camera end exposing the 2 small ribbon connectors on the bottom.
-Peel back the tape and GENTLY lift the ribbon connectors out of the board. Place the motherboard/camera unit to the side for now.
-Remove all the black and silver screws for the metal piece. The lcd should stay in place as the mouthpiece plastics kinda hold it for you, but you should still support it to keep from hurting the connections.
-Viola, keyboard access. Remember when you put it back together be sure to re-tape all the connections, else when you drop your phone one of them may pop loose.
Keeping the motherboard and camera/imea plate all as one module saves you from a very difficult connection and will help you keep everything aligned when reassembling it.
I guess the spacebar has 2 functioning buttons, (left and right) ... well my right side just konked on me, and i was wondering if a replacement keyboard off ebay will fix this, or are they just the button "covers"?
the "buttons" are just plastic nubs that make contact on a board behind it. That board would be what you need. I dont know if there are any on eBay, but I have a spare one if you want to PM me for details.
I dropped my G1 about 6 months ago and was devastated. After entirely too much research I finally got the guts to purchase a replacement digitizer and managed to install it successfully. However, in the process I managed to rip the LCD ribbon cable. I then had to order a replacement LCD screen. I've also damaged one of the black ribbon cables pretty severely causing the touchscreen to become unresponsive sporadically. I've just placed an order for one of those ribbon cables and will hopefully have that up and running soon. I've also purchased an entire new housing unit to rebuild the phone to make it look as new.
Now when I first took this thing apart I was by NO MEANS an expert or have ever done something like this before. I'm just an avid enthusiast who wanted to save a little money, feel a sense of accomplishment and to learn a few things along the way. I technically paid nearly the same amount of money it would have cost me to send the unit to HTC for repair, however i've learned everything there is to know about my phone's hardware. I know which board does what and are extremely confident about fixing ANY hardware problem in the future.
If you have the time, patience, and truly want to become confident about the workings of your phone, then I highly recommend fixing it yourself. I've bought my parts for VERY cheap off of reputable ebay buyers. You can find EVERY single piece for your phone on Ebay. My LCD has 1 dead pixel, but I guess that's the risk you take when you buy really cheap parts.
Hope this helps.

[Q] Guide on Replacing the Digitizer

Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
keithgrobertson said:
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
Click to expand...
Click to collapse
Try this http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/1
Or, this http://www.youtube.com/watch?v=TbR56jSplRs
Broke my digitizer and did the job myself using the youtube guide above. Just used straight up superglue to glue digitizer to frame. I put a bunch on the top and bottom and very little on the sides.
Amazingly the phone worked when i put it back together... for a while until I screwed up one of the ribbons by opening it a bunch more times. Be extra careful with these, especially the volume/camera ribbon. You can bend it pretty easily trying to slide it back into its slot.
Good luck.
NB: Theres places that will do it for as little as $90 in case you don't want to take the risk.
http://www.ubreakifix.com/
Thanks for posting the youtube link. I can't even quote the post because it involves an external link. The video was vague on details and the quality is crap but it did the trick.
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from amazon and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Metacat said:
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from ebay and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Click to expand...
Click to collapse
I replaced my digitizer, and had the EXACT same thing happen (not the light sensor but the line in the screen that doesnt respond to touch).
Get a new digitizer, but get it from someone else.
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Metacat said:
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Click to expand...
Click to collapse
No. I sold it and let someone else deal with it. Didn't have the time to replace the digitizer again. Too much of a hassle.
I just replaced a digitizer on an atrix... i didnt put any adhesive on it because there was what i thought was adhesive strips on the digitizer... but there's strips on the screen that doesnt respond, i heated it n tried reattaching the digitizer a few times n sometimes the home and back button will work, sometimes they wont... any suggestions? could the lack of adhesive cause this?
Menu buttons problem
if menu buttons is freeze till I block and then unblock my phone is it digitizer problem ?
what do you mean by " block/unblock" ?
Sent from my HTC Desire CDMA using XDA
He means lock/unlock.
Go the ifixit route!
Just went through 3 digitizers in my repair, and wanted to share my experience/caveats
I bought one digitizer from All4Cellular for $25, and the others with a 20% discount a few days later, for $20.
I installed
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Got the idea to move the LCD screen from another RepairUniverse YouTube video and a previous post here, and tried installing the digitizer from the front face of the phone. It was still a delicate matter to bend the flex cable so that it fit through the slot, and then re-position the LCD and align the sticky strips of the digitizer on the LCD and casing. Part of the digitizer worked this time - a 1cm vertical strip on the left fowled any attempt to touch icons or use a keyboard, so I thought I had damaged things again (doh!).
Hoping third time was the charm, I completely disassembled the phone using the guide in the 'ifixit' link, since a digitizer/case assembly was suggested in another thread. The rear camera just needs to be raised above the casing so the thin plate can move upward, and the LCD pops out easily if the sides of the casing are delicately pulled. The digitizer can be positioned easily and with minimal bending/twisting of the flex cables.
When reconnecting everything the third time, I noticed that pressing down on the front camera / digitizer connection *with the rubber boot in place* didn't pass when pulling the connected assembly upward. So I pulled the rubber boot out of the way and snapped the camera / digitizer connection firmly, then re-inserted the boot. A loose connection might have been the culprit for the nonfunctioning part of the digitizer in the second test.
@MrSaba - I had the same issue with capacitive buttons - perhaps because the screen senses touch and disables those buttons. Replacing the digitizer solved the issue
trouble
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
drZeT said:
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
Click to expand...
Click to collapse
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
jjwatmyself said:
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
The first one was with the red stripe indeed, from china. The one with a frame came from UK, "used but tested OK". original screen is gone - tore off flex cable while removing.
Well, update...
2 screens bought on eBay were BAD. Had to wait full month for authorised motorola service to change the digitizer. Must say though that both merchants on ebay refunded, no questions asked. Lessons learned - pay more, wait longer, never give up
DrJCFitz said:
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Click to expand...
Click to collapse
What I noticed on their video was that their folded digitizer connector magically unseats itself during the disassembly transition. I had to pry mine off based purely on guesswork and think I might have broken the flip-chip that is stuck onto the frame with double-sided tape. Like yours, my touchscreen doesn't respond at all, despite there being no cable tears. I'm going to try and re-heat that flip chip and maybe get the connections to work again (doubtful).
To anyone else out there attempting this... when you go to remove the touchscreen, HEAT THE CONNECTOR so that you can gently pry it out!
Bad screen I got 3 before it worked its fine now if old one partially works new one doesn't screen is junk took mine apart several times to figure out screens were junk...guess they felt sorry for me give me my money back plus free working screen.from amazon
Also that lock clamp u mentioned first video I watched didn't show unlocking that I just pulled it out and pushed back in it was the 2 screen that I figured out it needed to be pryed loose by the white clamp but guess I didn't damage it..
Sent from my HTC One X+ using xda premium
I have just put in my second digitiser. The first was one had a red stripe, which was junk, the second on I bought had the plastic round the edge and the digitiser.
I put it in and it worked fine no dead spots at all. Then 12 hours in it started to stop working intermittently. Then 24 hours after that while on charge its dead again. I reflashed notattrix and still nothing. I've confirmed all the ribbon connectors are firmly in place and everything looks right.
Any ideas whats wrong?
thanks
Jonnym

TF201 DIY screen replacement

Hi,
It seem like there are a lot of people that has TF201s with broken screens, but very little information about how to DIY screen replacement, so I wanted to post my bad experience here as a warning to people, so that they know what they get into.
The screen on my TF201 cracked (dropped on the floor - only the screen was damaged, the LCD and digitizer still worked) so I searched around the web to find ways to replace the screen - without luck
I did find instructions on how to open the device and I also found original glass/digitizer replacement parts on eBay originating from China at about $100 so I took the chance and ordered a new screen. It arrived 2 weeks after and looked good.
With the instructions on how to disassemble the TF201 posted on this forum, it was quickly open and the glass/digitizer/LCD is one subassembly connected to the mainboard with two flex cables - one for the LCD and one for the digitizer.
Next step is to power off the system internally. There is a small internal switch in the lower left corner that you should switch to the off position. The LCD and digitizer cables can now be disconnected from the mainboard. The connectors open easily by putting a nail under the white frame of the correctors and pulling the frame up and then pull out the flex cables. You now have the glass/digitizer/LCD separated from the mainboard.
The LCD has a few screws to hold it to the plastic frame - these should be removed at this step. Mine only has two screws mounted although there is room for more (bad assembly quality or a fix for screen bleeding???)
Now comes the hard part and the part where I failed! There is a plastic frame around the edges of the glass that you need to remove and mount on the new glass. This plastic part holds all the taps that keep the tablet together and it is taped to the glass with some VERY sticky tape!
I used a scalpel to cut between the plastic and the glass with the result that the glass broke in tiny pieces as I went around, but as I saw no other way I kept going... It might have been better to use a heat gun or a hairblower to heat up the glue before trying to remove it, but I was worried that the LCD might be damaged by the heat.
The plastic frame has to be removed first to have access to the foam tape that is used to tape the LCD to the glass/digitizer. Once the plastic frame was off, I again used the knife to gently cut the foam tape (around 1 mm thick) all around the LCD screen so that this can be removed from the glass.
Here I might have made my second mistake. I was worried that I would cut too deep into the foam and hit the LCD screen, but the foam at the bottom of the screen is a little wider than the rest and as I tried to remove the screen I used too much force and might have damaged the LCD - the end result was that also the LCD was damaged in the process. The damage might also have been caused by me pressing too hard on the screen during the removal of the plastic frame (might actually be more likely as the glass was broken across the screen and the damage I was seeing when I turned on the screen was following the same line as the crack).
Well, I got the LCD off the broken screen and though I had been successful even thought it had taken a couple of hours to get there (I could not visually see that the LCD was damaged at this point).
Then on to the assembly with the new screen/digitizer! I had some double sided tape that I used to tape the screen to the plastic, but decided to do a quick test before I fully assembled the unit and this turned out to be a good idea!
I mounted the LCD screen with just the screws and connected the flex cables back into the connectors (these can be a little tricky to get in, so just be patient and keep wiggling them in and close the latches). I enabled the power again and pressed the power button and: DAMM - THE LCD IS BROKE!!!!
After wiggling a little with the LCD cable I was able to get a partial image, but it was evident that I had mishandled the LCD screen during the disassembly and I needed a new screen to get my tablet working again - now I was glad that I did not glue the LCD to the glass, so that I needed both a new LCD and a new glass/digitizer!
Off to the web to search for a replacement LCD screen... Hmm, lots of ebay listings for TF201 replacement LCDs, but none of them looked like the original I had... Then I searched for the partnumber on the LCD I took out (Hannstar HSD101PWW2 rev. 0-A00) and I did find a few items priced around $100.
Before I started to spend more money on the device I wanted to check our if the digitizer was actually working, so I connected the tabled to my TV using the HDMI output to test...WHAT?? THE X-AXIS ON THE DIGITIZER WAS REVERTED!!!
I double checked the flex cable connections, but everything was in order. I then compare my broken screen with the replacement part and noticed that the signal routing on the flex cable for the new part looked quite different than the original.
I emailed the company that sold me the screen and he replied back that they JUST heard that some other customer have had the same problem - there might be different versions for the digitizer used in the TF201 (perhaps depending on production time)!!!
He suggested that I tried a hard reboot and a system reset to default and I tried that without luck.
I also tried to find a way to do a 5 point screen calibration, but this does not seem to be supported.
Does anyone know of a way to revert the x axis by modifying a configuration file - and can that be done without rooting the device??
Have anyone successfully replaced their screen - if so, could you reply with the partnumber listed on the flex cable? Mine is: 3KA12-5SCA01, 18100-10180100.
They did offer to refund the price of the screen if I shipped the screen back to them, but I will most likely damage the screen when trying to remove the plastic frame and it will cost me shipping the part back to China. After a few mails exchanges they offered a $82 refund and I accepted that.
I now have a TF201 with a working touch screen that has the x-axis inverted and no LCD...
Continued...
SUMMARY/LEARNING:
- IF YOUR SCREEN ONLY HAS A SMALL CRACK - LIVE WITH IT OR TRY TO FIX IT WITH AUTO GLASS REPAIR GLUE
- IF YOU REALLY WANT TO GO FOR DIY SCREEN REPLACEMENT, MAKE SURE THAT YOU GET A DIGITIZER THAT WORKS WITH YOUR UNIT!
- WHEN REMOVING THE PLASTIC FRAME FROM THE GLASS BE VERY CAREFULL NOT TO DAMAGE THE LCD SCREEN BY PRESSING ON THE BROKEN GLASS AND TRY TO USE A HAIR DRYER TO HEAT UP THE GLUE (NOT TRIED THIS MYSELF)
- WHEN CUTTING THE FOAM TAPE BETWEEN THE LCD AND THE SCREEN BE VERY CAREFULL TO CUT THOUGH ALL THE TAPE BEFORE TRYING TO REMOVE THE LCD
I now have a TF201 with a working touch screen that has the x-axis inverted and no LCD... Unless I get the touch screen issue resolved I most likely will get a TF700 instead of my broken prime - I really loved the prime for the 4 months I had it working...
Happened to me too!
Bought a prime with an already cracked glass with the hope to fix it, as i do with most higrer-end devices (phones in particular)...
I intended to pass it on to my mom as her first tablet. When i bought it, it was fully usable and after two weeks (before the digitizer got delivered) my mom got addicted to it.
Then i got the digitizer in the mail... I cracker the tablet open, unhooked the front assembly and started going at it. First i tried removing the screws in the hope that the lcd would easily seperate from the digitizer. Sadly that wasn't the case so my next action was to try and seperate the lcd and digitizer from the plastic frame... i broke off a piece of black glass that was over the frame and started working my way arround the gap with small but tough shears so that i would brake the glass off from the frame, working my way arround the screen and digitizer, while removing any broken glass from the frame at the same time. Took two hours and the two were seperated. Tried to connect the lcd to the tablet to see if it still worked, and it did. So i was left with what i thought was an easy task of seperating the lcd and digitizer by lifting the adhesive. Top, left and right went rather easily. I added thin plastic mediator-like opening tools arround the edge so that the lcd wouldn't get stuck back to the adhesive (was trying to preserve the adhesive stips for re-installation). When only the bottom one was left still attached i went with the experience/common-sence approach to start prying the lcd away from the digitizer where i thought the adhesive strip would be the same size and would easily give way... That's probably when the lcd couldn't take it and cracked.
Had i used a scalpel all arround- i would have been left with a perfectly working tablet, but all i had was a tablet with a cracked lcd. So i gave up on this not wanting to crack another (costly) lcd and sold it on ebay. That, and because it was a little too big and heavy to use on the train every day going and from work.
So what have i learned from this?
1. For tablets with glue-stripped-on LCD's ALWAYS break the glass arround the frame (with high caution) to seperate the digitizer+LCD from the frame
2. ALWAYS use a scalpel in between the adhesive and digitizer (making shure that when you insert it, you can see it infront of the LCD and behind the digitizer. If needed, angle the scalpel so that it rests on the digitizer and not the LCD. (LCD pannel edges ussually have a strip of metal or plastic arround the edge, so you won't damage them if you use light force on that area, as opposed to the glass itself.)
Hope people who do break their primes get to see these posts before attempting any repairs.
ThomasKJ said:
Before I started to spend more money on the device I wanted to check our if the digitizer was actually working, so I connected the tabled to my TV using the HDMI output to test...WHAT?? THE X-AXIS ON THE DIGITIZER WAS REVERTED!!!
I double checked the flex cable connections, but everything was in order. I then compare my broken screen with the replacement part and noticed that the signal routing on the flex cable for the new part looked quite different than the original.
I emailed the company that sold me the screen and he replied back that they JUST heard that some other customer have had the same problem - there might be different versions for the digitizer used in the TF201 (perhaps depending on production time)!!!
He suggested that I tried a hard reboot and a system reset to default and I tried that without luck.
I also tried to find a way to do a 5 point screen calibration, but this does not seem to be stouchscreenupported.
Does anyone know of a way to revert the x axis by modifying a configuration file - and can that be done without rooting the device??
Have anyone successfully replaced their screen - if so, could you reply with the partnumber listed on the flex cable? Mine is: 3KA12-5SCA01, 18100-10180100.
Click to expand...
Click to collapse
I have exact same problem with the touchscreen. X-AXIS is reverted but not fully, touchscreen works off pressing like a mirror on the left to the right.
I'ts video youtu.be/XUN_0q5I4ng
my touchscreen partnumber is same.
Сould you upload photos of the touchscreen cables differences between what you had originally and those that worked not correctly?
Where did you find the part number for the digitzer? Is it near the tiny QR code, or on it?
I have the same problem x-axis is reverted. Still wonder why? The original broken glass/digitizer was working fine.
Please share if you guys found the solution. I will do it too.
Thank!
Theres a vid about this. i will post it soon. i'm only using my phone. my prime is with my dad in china. i dont know when i'm getting it back in 2 or mor week i guess? surely i'll be noob again when i get it back.
I have the same problem too. Broken digitizer & lcd.. Got a replacement digitizer and the x-axis was inverted, sent it back and got the full refund.
After that i texted a few mails with another seller that knows the problem, he told me there are two versions of digitizers for the tf201. He sent out the (i hope) right one today, I will post the seller if this one works (takes about two weeks to get it..)
OP started this thread in another forum I found via google search where some guy figured out how to fix the x-axis problem by changing something in the source.. however I think he will release a patch after some more testing but he can't test right now because he has no lcd atm. Here's the thread:
bit.ly/OXx6us (hope it's allowed to post this)
same thing
I have exactly the same issue: axis-x is inverted.
I got it, thought it's broken or fake or whatever and sent it back. Bought another one from a different seller. Same problem.
I'm not a programmer, but I feel it can be fixed easy on a software level (just don't know where to look for it)
Here is my video:
digitizer on the way from China
Any one find a solution for this yet?
I have a digitizer on the way from China.
Just a bump to catch someones attention I hope.
I'm waiting to hear from someone if they found a supplier that will send the right screen, or if they know how to compile the kernel to make the screwed up screens work right.
Kind of holding off ordering mine at the moment.
All of a sudden there are a lot of these for sale on Ebay.
And there hasn't been much chatter on defective ones lately.
Makes me wonder if it was just a specific seller that had a bad batch.
Caught a guy trying to sell his TF201 with a broken LCD that he claims broke while replacing the digitizer.
Turns out he is trying to sell his with one of the inverted digitizers and not stating so in the auction.
I ordered a replacement from New Jersy and canceled the one from china I will see what happens when it gets here.
I will definately test it before I tape it down.
If it works let me know. I'm in Canada and would rather pay a bit more for a properly working one than some knockoff that I have to be a programmer to get working.
Any news on your replacement yet?
Nightpath said:
Any news on your replacement yet?
Click to expand...
Click to collapse
I got my second replacement-digitizer and it's inverted too.. so frustrating!
As there are so many people with this problem I hope some expierienced guy will take a look at the touchscreen-driver and post a little workaround. It is possible to fix this problem by editing the driver but I don't know how it exactly has to be done.
I will share my problem.
My screen broke, however, the LCD and touch still worked.
I ordered a new screen for ASUS authorized service, because using a tablet with a cracked screen is horrible.
I thought it would be posted only the digitizer, but no, the Asus offers LCD screen with digitizer, it is not necessary to work to separate the two parts.
A professional did the replacement.
The problem is that the new set is crazy.
When the tablet is horizontal | === |,
* think that is vertically
| = |
| = |
* and otherwise also.
I think I was unlucky.
* I'm about to order a new set, this time, buy direct from asusparts.eu
Hmmm...where exactly did you order your first digitizer (touchscreen)? And that site you linked sucks, no pictures of any of the items to make sure you're getting the right one.
Received mine yesterday, [email protected]#$** piece of crap!!
It is inverted,it is going back.
First they wanted to give me a discount to keep it, idiots!
Then theyy want to send me another in exchange, they don't seem to understand the problem is they are all going to be the same if they are from the same batch.
Any one found a source for a good one yet?
I am going to try and see if Asus will sell them directly to the end user.
They sell laptop parts, so maybe they will do a digitizer.
I'll post my findings.
Cool. I work long days here in Canada (military, sigh) so I don't get much of a chance to do anything. Let me know as soon as you find out TRJ

Categories

Resources