Dear Friends,
I bought an MDA 2 (QTEK2020) and a wired XAIOX X3 GPS receiver and installed TOMTOM Navigator 3.01
The Xaiox is a rather new type I think (can receive up to 16 satellites)
I saw in the list of GPS Receivers that this brand XAIOX was not in, but on the website of Xaiox is mentionned that the gps protocol is NMEA 0183v3 compatible and you should pick 9600 baud rate.
In the TomTom list I saw NMEA 0183v2 9600 (version 2 only). I checked this one and waited 45 minutes,but didn't get any connection.
The field 'receive incomming beams' (like infrared,...) is set out,as i read this could block an incomming port like the receiver.
My Xaiox receiver has no lights,so I can't see any status. It had a serial cable out,and i bought a small piece to convert to USB, and this USB connects to a smaller type of usb on the bottom of the MDA2.
I'm not sure if I should choose 'Serial on Com1' or Serial on USB. But I tried both of them and still no connection. I also tried all of the other brands in the list like Destinator 3,SIRF 9600,TOMTOM,... but no connection.
This GPS receiver is brand new, and I tried it at home with power cable in, cause i the gps receiver had to load also. Also on the road no connection.
I updated to TomTom 3.03 but no change.
1>Is the GPS receiver NMEA protocol V3 too high for the one in the TomTom Navigator list (NMEA v2 only)?
2>Do I choose the wrong port or gps receiver model ?
3>Do I have to close phone connections in order to use GPS ?
I tried 'Turn Flight Mode Off' but it didn't work either...strange stuff...
Thanks and a happy 2005 everyone!!!![/b]
Usb will not work, it will need to be wired for serial connection, what is this mini usb converter you are using? The phone is not capable of communicating with a usb gps receiver because both the gps and the phone are usb slave devices and have no capability to talk to one another.
Related
Hello,
I bought an MDA 2 (QTEK2020) and a wired XAIOX X3 GPS receiver and installed TOMTOM Navigator 3.01
I have 1.72.00WWE latest rom version.
The Xaiox is a rather new type I think (can receive up to 16 satellites)
I saw in the list of GPS Receivers that this brand XAIOX was not in, but on the website of Xaiox is mentionned that the gps protocol is NMEA 0183v3 compatible and you should pick 9600 baud rate.
In the TomTom list I saw NMEA 0183v2 9600 (version 2 only). I checked this one and waited 45 minutes,but didn't get any connection.
I always see GPS SIGNAL UNRELIABLE
The field 'receive incomming beams' (like infrared,...) is set out,as i read this could block an incomming port like the receiver.
My Xaiox receiver has no lights,so I can't see any status. It had a serial cable out,and i bought a small piece to convert to USB, and this USB connects to a smaller type of usb on the bottom of the MDA2.
I'm not sure if I should choose 'Serial on Com1' or Serial on USB. But I tried both of them and still no connection. I also tried all of the other brands in the list like Destinator 3,SIRF 9600,TOMTOM,... but no connection.
This GPS receiver is brand new, and I tried it at home with power cable in, cause the gps receiver had to load also. Also on the road no connection.
I updated to TomTom 3.03 but no change.
1>Is the GPS receiver NMEA protocol V3 too high for the one in the TomTom Navigator list (NMEA v2 only)?
2>Do I choose the wrong port or gps receiver model ?
3>Do I have to close phone connections in order to use GPS ?
I tried 'Turn Flight Mode Off' but it didn't work either...strange stuff...
Thanks and a happy 2005 everyone!!!!
ir beamsa receive off
Hello,
Try to switch of the infrared you can find his under connections
you will have a com1 now and i think it will work
greatings and happy newyear!
I have updated my XDAii with WM2005 (1.60c), everything I tested works fine, but I only have a problem with MN4.2 and an original Navigon BT Mouse.
I have changed the two .ini-files (prefs.ini + spgps.ini) to COM4 (the outgoing port).
Switching on the BT-Mouse the blue BT-LED of the mouse is flashing but after starting of MN the BT-LED of the mouse stays off and there's no connection.
I've never seen the mouse with no BT-LED before, because when the mouse is on BT is also on.
It seems that MN says the mouse to switch off BT ???
With Navio (for example) the connection is working on COM4.
It also worked with WM2003.
Has anybody any ideas?
Greetings
ossi
I use the GNS 5840 BT/TMC receiver.
It seems that the WM 5.0 BT stack does not allow for serial connection at 38400 baud which is needed by GNS/Navigon receivers.
I cannot connect at all to my receiver.
Error message from CruxView: "Could not set baudrate"
Sascha
My mouse is running with 4800 Baud and with Navio it works, only with MN4.2 i have this problem.
Ossi
The original Navigon GPS receiver (Navigon modular) which was shipped with MN|4.x is manufactured by GNS and runs on 38400 baud.
Sascha
It's an updated MN4.2 (i think 1.5 was the version with my receiver) and it worked with WM2003.
ossi
i am having a problem connecting to both recievers (royaltek rgt-1000 and Leadtek Wireless GPS Reciever)
I am trying to get them to work with my Wizard (t-mobile Vario)
but i am not getting anywhere.......HELP.......... i can put the in and outgoing ports on the bluetooth thingy as com6 and com7 but in the tom tom i can not even see those.................HELP!!!!!!!!
Sounds like you are running TT5 without the 5.21 update, this sorts that problem
Current Setup
1. Hard-SPL-240-MFG.exe
2. titan_radio_3.27.00.exe
3. dcd_titan_kitchen_2.3.2.rar
Everthing works with some data issues when downloading large files due to a but in the titan_radio_3.27.00.exe (I can live with it).
The problem is when I partnership the Titan with the Holux 240 GPS external Bluetooth GPS it does not connect. I can see the device but never can connect, Yes I use the standard 0000 passcode. Other Bluetooth devices ie my headset Moto N700 and car head unit Sony BT-2500, audio and hands free all work. I'll be travelling to an area with no Digital service and would like to use the GPS with Navigation software.
When I restore the original TELCOM ROM, I have no problems with Holux 240, Moto N700 and Sony BT-2500. When I connect I see a serial port as a list service.
Some threads talk about a fix for the Bluetooth stack? nueROM or Dogguy in PPCGeek.
Another item to be noted. With Bluethooth A2DP headsets, if I connect once do I have the reconnect to the device again? The Sony BT-2500 pairs with with Titan (any CE ROM) but I need to resave the audio everytime.
I haven't tried my Holux GPSlim 240 with any of the new ROMs yet, but I'll try to remember to give it a shot when I got off work.
I'm curious though - why would you want to use external GPS when you can use the one built into the phone? My Titan's GPS seems to be more accurate than my Holux 240. You don't need digital service to use the GPS, unless you're using Google Maps or some other program that downloads maps on the fly. If you already have a navigation program with maps, just use the built-in GPS.
I thought the GPS chip in the Titan was a gpsOne that uses digital cellular signal from the towers to triangulates your position.
From phonenews.com
Installing this update will enable GPS to function inside your HTC Titan. It enables the gpsOne chipset in your device to function as a standard GPS device, compatible with Windows Mobile 5 & 6 GPS applications, including Google Maps, Windows Live for Mobile, and navigation software such as TomTom Navigator. Keep in mind that gpsOne is not autonomous GPS, you will need to have home network coverage in order to maintain a GPS lock.
I posted about this same problem with my Holux 1200. The internal GPS always takes 5+ minutes to connect for me no matter where I am or what I use to juimp start it, so there are times when I'd want to use my external receiver for a quick connection. When setting up my receiver I set the outgoing COM port to 0. Then from the external GPS settings I try to set the GPS hardware port to 0 also, but the setting doesn't stick. It always reverts back to the default which is none. Some people have told me that they never set the GPS hardware port, but I always had to previously to use my GPS receiver. Now with the internal GPS enabled I can't.
Found some more information
gpsOne can operate in 4 modes:
Standalone - Your handset has no connection to the network, and uses only the GPS satellite signals it can currently receive to try and establish a location.
MS Based - Your handset is connected to the network, and uses the GPS signals + a location signal from the network.
MS Assisted - Your handset is connected to the network, uses GPS signals + a location signal then relays its 'fix' to the server, which then uses the signal strength from your phone to the network towers to further plot your position. You can still maintain voice communication in this scenario, but not 'Internet/Network service' ie Web Browser, IM, streaming TV etc..
MS Assisted/Hybrid - Same as above, but network functionality remains. Normally only in areas with exceptional coverage.
Hello, I've bought an NL-324BTR bluetooth TMC riceiver wich "works" on COM2 when I pair it with bluetooth. The problem is that everytime I start bluetooth on my device (I use phone weaver to autostart bluetooth connection in my car) the port COM2 doesn't reconnetc automatically and I have to go to the bluetooth settings and reconnect it manually. This is a very very bad issue for me (as you can imagine I can't drive and reconnect devices in the same time ). Is there an app, a script or something like that wich allows me to reconnect the COM automatically?
Uh, I was forgetting, in my car I've installed a parrot bluetooth hands free car kit wich works perfectly and automatically reconnect each time. I've also tried to use the COM with or without the parrot connection established but nothing has changed, no way to reconnect it automatically.
Any suggestion?
Thanks and regards
Andrea