Hi guys,
I have a T-Mobile (Wallaby PW10B1). When I inserted a local SIM, it asked me the SIM Unlock code. Currently I don't have the serial cable. I just only have a USB cable to connect to the computer. It has a 32 MB mem card. Here is the specification:
Hardware: PW10B1
Platform: PocketPC 2003
ROM Version: 4.01.16.ENG
ROM Date: 02/04/04
Radio Version: 6.25.02
Protocol Version: 324e4
Can u please help me to Unlock the Pocket PC Phone Edition?
Thanx in advance
Berhane
Please can u help me to unlock the phone.
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_Unlock2
HTH
Stefan
Thanks LumpiStefan for your reply.
Currently I have only 32 MB SD card. I'll find a 64 MB SD card and try it
Berhane
Me Too...
I had almost exactly the same specs as berhane, except I had a 512 card. I installed the xda-special rom and it installed correctly I think ???
But my phone still says it's locked. Did I miss anything.
Here is what I did.......
Programme A did not work for me for some reason so I did the following steps.
1. downloaded xdatools and backed up my old rom.
2. ran osimagetool --register
3. ran osimagetool for source used NK.nbf in english directory for target I used xda SD card and copied the image to the card.
4. held down the on/off button and hit soft reset to get into bootloader
5. bootloader detected rom image and so I flashed rom
6. did a hard reset of xda
I now have the xda-developer special edition rom with the following specs
rom version: 3.17.03 ENG
rom date: 05/15/03
radio version: 6.25.02
protocol version: 324e4
but when I insert try turn the phone on it still asks for a sim unlock.
I had the sim in the xda when I flashed it was that the problem ???
berhane....I think you can get away with a 32meg card because the image is only 15meg in size but I'm not sure.
Re: Me Too...
jodahall said:
radio version: 6.25.02
Click to expand...
Click to collapse
Unlock tool didn´t work with this Radio Version. You have to downgrade it also....
jodahall said:
berhane....I think you can get away with a 32meg card because the image is only 15meg in size but I'm not sure.
Click to expand...
Click to collapse
Image is only compressed about 15 MB uncompressed itts 32,x MB.
Believe me. Flashed about 100 times a new ROM to a Wallaby device....
HTH
Stefan
Hey Guys,
When tried to execute the pnewbootloader command
i.e. c:\XDATools\pnewbootloader bootloader_v5_15.nb0
it prompts an error message " Unable to find flash info offset, cannot
disable bootloader write protect."
What can I do with this error meassage.
Here is my memory Information:
Total Main memory: 31.01 MB (32 MB)
Storage Card Memory: 29.14 MB (32 MB)
What can I do with this configuration
Thanx in advance
Berhane
Try this tools....
HTH
Stefan
Thanks HTH. It works with your new utility
now it goes one step
i.e.
C:\XDA\all-itsutils-050416>pnewbootloader.exe bootloader_v5_15.nb0
Copying C:\XDA\all-itsutils-050416\itsutils.dll to WCE:\windows\itsutils.dll
protection found at 8c0d60f8
but it doesn't say result: 00000000 00000000
Is it okay and continue with the rest of the procedure?
Thanks in advance
Berhane
Yes. You should be able to proceed with the rest of the procesure...
Stefan
Thanks stefan.
The boot loader is changed now. As I mentioned, I only have 32 MB and when I format the SD Memory, I can only use 30.5 MB and the the special ROM file size is 31.5 MB file. I 've got a 64 MB Memory (multimedia memory from Nokia 6230 Mobile) but my XDA didn't recognize the SD memory.
Anyways thank u very much Stefan, I'll find another SD memory and try it.
Berhane
You do not need to format the 32 meg sd card, xdatools will do its own format, I am sure I did an sd rom flash with 32 meg card in the past.
Thanx Cruisin-thru for your reply.
Can u tell me the procedure how to copy the ROM (NK.nbf) with the XDATools
Thanx in advance
Berhane
osiamgetool uses the xdatools in the Background. So just run this file...
Instructions are also available here:
ftp://xda:[email protected]/Wallaby/Tools/XDAtools_Manual.zip
Stefan
Thanx Setefan.
I 've got error message when I tried to copy the ROM image with XDATool.
First , I tried to copy the image file and starts copying, when the 'Time Left: 0:51' it pop ups with this error message.
ITWriteSDCard: The system cannot write to the specified device
Writing osimage: The system cannot write to the specified device
ITWriteSDCard: The system cannot write to the specified device
Is it b/c of the shortage of Capacity of the SD card . (I 've only 32 MB)?
Any Idea?
Thanx in advance
Berhane
Hi guys,
My MDA has only 32 MB Internal memory and 32 MB SD card. With this configuration, am I able to do the flashing process?
Thanks
Berhane
berhane said:
My MDA has only 32 MB Internal memory and 32 MB SD card. With this configuration, am I able to do the flashing process?
Click to expand...
Click to collapse
32 MB internal are no problem. But i'm nearly 100% sure, that your SD-Card have to be bigger.
My smallest one is 64 MB, so i can't test it.
But i've tried a backup of the Magician device, that has 64 MB internal Memory. Backup with 64 MB SD-Card didn't work. Got an error, that there isn't enough space. So i would assume it's the same with the Wallaby and 32 MB SD-Card.
You're Error Message you've got writing to SD-Card comes from that problem.
I would suggest to buy or lent a bigger SD-Card and use this for flashing....
64 MB Cards costs about 10 Euro......
HTH
Stefan
Thank you very much stefan.
I'll try to find a 64 MB SD Card.
Is there any ROM image which is less than 32 MB. (i.e. 15 MB) which has less software just to check.
Thanks you again stefan
Berhane
No. ROM-size is fixed to 32 MB. This depends on the hardware of the device.
Tho Original ROMs, that have the free space, so that we can add our own software in it, have also 32 MB....
Stefan
Thank you very very very much stefan and the rest of the team
I have successfully unlocked my mobile.
I have one question for u.
How can I upgrade the Windows from Special XDA ROM Edition to newer version (i.e. tested and well working with MDA) mobiles
Thanks again
Just the same procedure.
You can do it by flashing via SD-Card (safest way) or using the exe-File.
In my opinion the best ROM to use is the 4.01.12....
Stefan
Related
I dont have MDA yet , but today some guy want to sell me this sp.
I need information how to check avail RAM/ROM memory , its default MDA expanded by memory card (RAM?) or its build-in so memory card slot is empty?
Regards
Adam
in my system settings under memory i can see how much mem i have
left i can also set the slide between storage mem and program mem
my xda / qtek /mda ...... htc wallaby
dont have anything in it's SD port
and i'm getting myself a 256MB card for it for xmas
about rom then you cant put stuff in the rom other then at flash time (the time you flash your rom with the window CE pocketpc200X os)
other then that the ROM is read only memory
all htc wallaby have a 32MB rom
think that goes even for the new xda2 line
re
But when i check avail mem it tells me ROM: bla bla / RAM: bla bla ?
its important i dont want to be cheated. From my info MDA/XDA got 32mbrom (buildin) and 32ram (buildin)
HELP!
and 32ram (buildin)
Click to expand...
Click to collapse
thats the older version the newer versions of the xda's (dont mean xda2 here)
have 64MB buildin
older?
Older version is more suxxy than 64mb version ? or its just memory incrase?
as far as i know the only difference is mem
Hi i recently updated the roms through O2 site everything is fine just i cant seem to install programs ie tomtom or any other cab files???!! can anyone help me. All it does is shows the installation screen with the spinning redblueyellowgreen box and thats it. Im confused why its not doing anything.
Kidd
Rom Ver 2.21.4.1 WWE
Rom Date 3/9/06
Radio Version 02.07.10
Protocol Ver 413.1.03
ExtRom Ver 2.21.4.101
The ROM is screwed up..
try reflashing..
its the memory card. Just brought it from ebay 4gb unbranded. I used a old 512mb card and its fine with that. Its when you activate programs on the card it stops and starts. I already formated the card with windows fat32 that didnt work and the panasonic formatting program. It did work for abit but not anymore. Please help
kidd78 said:
its the memory card. Just brought it from ebay 4gb unbranded. I used a old 512mb card and its fine with that. Its when you activate programs on the card it stops and starts. I already formated the card with windows fat32 that didnt work and the panasonic formatting program. It did work for abit but not anymore. Please help
Click to expand...
Click to collapse
Not sure, but you can try research on the highest capacity a Wizard can take. And, take note of possible scam on high cap unbranded memory cards. E.g. try copying full 4GB contents into the card, just to make sure it is now a scam card.
ok copied up to 3.88 gb of mp3s so its pretty much a 4gb. I stuck the mini sd into a old pda Acer N30 (adapted) and it seems to work fine. Seems like the card is the problem as i have no problems using my old 512mb mini sd. Apparently its a samsung card. Im really stumped.
i have a 4gb microsd and It seems to have some problems.I'm using Schaps rom so my phone sees the card and I was able to put two small picture files but now when I try and open them i get an error. I cant erase these pictures. When I try it seems like there erased but when I reopen the storage card folder their still there. I downloaded Storage Tools to format it, but when i do it looks like the format works but when I go back into the storage card folder the files are still there. If I try and scan the car with Storage Tools it hangs and then freezes my whole system, I then have to soft reset. Does anyone have any ideas I would like to use my 50 dollar card for more than filling the hole on the side of my hermes. Thanks in advance.
camero6989 said:
i have a 4gb microsd and It seems to have some problems.I'm using Schaps rom so my phone sees the card and I was able to put two small picture files but now when I try and open them i get an error. I cant erase these pictures. When I try it seems like there erased but when I reopen the storage card folder their still there. I downloaded Storage Tools to format it, but when i do it looks like the format works but when I go back into the storage card folder the files are still there. If I try and scan the car with Storage Tools it hangs and then freezes my whole system, I then have to soft reset. Does anyone have any ideas I would like to use my 50 dollar card for more than filling the hole on the side of my hermes. Thanks in advance.
Click to expand...
Click to collapse
Reformat the card using a PC, format with FAT32....enjoy
help me,
hi all help me,, my 8GB micro SD cant detect in my softbank X01HT. tank for reply..
amm_hazz said:
hi all help me,, my 8GB micro SD cant detect in my softbank X01HT. tank for reply..
Click to expand...
Click to collapse
You have WM5 or WM6 ? If you have the default OS from Softbank, it is WM5 and WM5 cannot read SDHC cards (ie you are limited at 2Gb cards)
Time to flash your ROM...
amm_hazz said:
hi all help me,, my 8GB micro SD cant detect in my softbank X01HT. tank for reply..
Click to expand...
Click to collapse
And if you dont want to flash, I can buy back the card from you
(I live in Tokyo)
Alcibiade said:
You have WM5 or WM6 ? If you have the default OS from Softbank, it is WM5 and WM5 cannot read SDHC cards (ie you are limited at 2Gb cards)
Time to flash your ROM...
Click to expand...
Click to collapse
i have WM6 ROM Version : CUSTEL V2,5 ROM date : 04/17/07 Radio Version : 1.16.00.00 protocol version : 32.53.7018.01H
i live in indonesia.
i need details tutorial for solved my problem... help me...
Alcibiade said:
And if you dont want to flash, I can buy back the card from you
(I live in Tokyo)
Click to expand...
Click to collapse
i want to flash ,give me ROM for tested can detect 8gb micro sd. tank you
problem solved ,,, http://forum.xda-developers.com/showthread.php?t=344338
Cool for you
amm_hazz said:
hi all help me,, my 8GB micro SD cant detect in my softbank X01HT. tank for reply..
Click to expand...
Click to collapse
Boss..beli di mana 8GB micro SD sama brp harganya ?
Thx
di tempat saya ada ,harganya 815rb
amm_hazz said:
di tempat saya ada ,harganya 815rb
Click to expand...
Click to collapse
Tempatnya dimana? Jakarta? kalo bisa nomor telp tokonya
Thx
hi eweryone,
i just tried a "RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship" on my non t-mobile hd2 and guess what: it works.
only thing i got to change is internet connection settings... as i am in three network in uk.
reason why i posted this thred is much more memory awailable for programs i found, like twice more. On stock rom i have around 250mb top.
Now i have: 458.74 total,179.82 used, 278.92MB FREE!!!
anyone got it too?
what does it mean exactly?
how can we use it...?
details:
hspl: 2.08
rom: RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship
radio: Radio_Leo_2.15.50.14
simlock: factory unlocked.
It's already used in many custom roms.
pkoper said:
It's already used in many custom roms.
Click to expand...
Click to collapse
you talk about ram memory, i'm not...#
quote from post 1 in THIS thread
This ROM contains SPL 3.03 and drivers 3.14 which are working INCORRECTLY with 2.08 HSPL. If you flash this ROM you will get only 70-80mb free RAM after Hard Reset.
Click to expand...
Click to collapse
ok once again, mabye i understand something incorrectly...
this are what system shows me...:
SD card & phone storage:
device
total storage 177.12MB
used storagr 98.11MB
free storage 79.01MB
total program 458.74MB
used program 168.64MB
free program 290.10MB!!! bare in mind that i have 2.08 hspl
on hardware information tab:
ram size 576MB
so, is that all normal?
wholly1 said:
ok once again, mabye i understand something incorrectly...
this are what system shows me...:
SD card & phone storage:
device
total storage 177.12MB
used storagr 98.11MB
free storage 79.01MB
total program 458.74MB
used program 168.64MB
free program 290.10MB!!! bare in mind that i have 2.08 hspl
on hardware information tab:
ram size 576MB
so, is that all normal?
Click to expand...
Click to collapse
yes , yes , yes. no need for a thread
wholly1 said:
total program 458.74MB
on hardware information tab:
ram size 576MB
Click to expand...
Click to collapse
graphics chipset takes 128MB for itself, the system gets whats left.
I flashed a stock rom
_HTC HD2_RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
and now I check my bootloader and it says
spl-2.08 cotullahspl
so what's wrong?
I saw around the forum that hspl is erased after stock flash?
whats wrong?
hspl is only erased if you restore an official rom from your microSD card.
This is noted in 4) in the HSPL thread.
dtechnology said:
hspl is only erased if you restore an official rom from your microSD card.
Click to expand...
Click to collapse
so how do I do that?
can it be done with my 8GB / 1GB sd?
what files do I import to my sd and how do I flash it?
You should really put a little more effort in searching yourself than just asking questions. If you read the HSPL thread it is all noted there and this question has been asked 1,000,000.48 times already.
okay, thanks anyways for the answer, I will check into it
Check this
Run HSPL3_PKG.exe and select SPL 1.66.0000 or a different Version with 0000 at the end.
HectiQ said:
so how do I do that?
can it be done with my 8GB / 1GB sd?
what files do I import to my sd and how do I flash it?
Click to expand...
Click to collapse
No sir, Don't use a 8GB SD-card to flashing Stock ROM!
Maximum 2GB is recommended.
Steps:
- Right klick on the HTC HD2_RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30. 50.07U_2.06.51.07_Ship select Extract (Winzip/Zip7/...)
- Copy the "RUU_signed.nbh" to SD card
- Rename the "RUU_signed.nbh" to "leoimg.nbh"
- Reset the device while pressing the volume down button.
- Follow the steps on your device.
Why wouldn't you be able to use a 8GB card? The only card I have is 8GB and I've used it 2 times to restore stock rom and it has gone perfectly...
[edit]
I just tried it again it at least works perfectly for me:
1. Format SD card through windows (FAT32)
2. place leoimg.nbh of official rom on it
3. Hold voldown and power to enter bootloader screen and press power to flash
It dit restart once about 20% through with a big exclimation mark, but restarted immidiatly and completed the flashing.
This has happened once before when I had HSPL'ed my device and restored it this way.
[/edit]
dtechnology said:
Why wouldn't you be able to use a 8GB card? The only card I have is 8GB and I've used it 2 times to restore stock rom and it has gone perfectly...
Click to expand...
Click to collapse
The reason way I mentioned (don't use a 8GB SD-card) is based on the feedback of users.
Flash stock ROM over a 8GB SD_cards don't work in almost 70% of the cases. so to prevent (lot of troubles) We mention to use preferable a 2GB or a 4GB SD (the latest who works in 85% of the cases)
ok guys, thanks for the feedback
+1 thanks for everyone