My Wallaby GSM Error fixed! Finally - MDA, XDA, 1010 General

Hi all,
Hope I may be of help to those who have GSM Error on their Wallabys. I have almost given up hope but I just searched the threads. This is basically what I did:
1. Download xda developers special rom and re-flash via sd card
2. Hard reset, press contact and calendar buttons (or a combination of both), volume button, and soft reset will bring you to the today homescreen (I cant remember exactly what buttons I pressed, I just pressed them all)
3. Re-boot phone, you will notice you still have no radio but you can now enter today homescreen (please take note the "start" menu is not there)
4. Align screen / stylus. You can do this by pressing Action Key then Calendar button.
5. Press Contact and Action Key (both) several times (I think around 20 times). You will hear clicking sound. This will bring out the "start" drop down menu. If it does not pop out, repeat again.
6. Download the correct RSU for your phone. Save into SD and copy to programs (same procedure as in wiki)
7. Run the RSU program, expect to fail at 1%. Re-boot. this time you will be able to active sync your phone again. (my wallaby did to my surprise)
8. I gave up on the RSU 4.16 (after countless tries) and I downloaded RSU 4.21 from xda-developers ftp (exe file) since I am now able to sync to my device.
9. Install RSU upgrade to your device, the phone will automatically re-boot.
10. Surprise! I was able to re-flash the RSU! (I think the problem is the RSU 4.16, try other 4.xx instead but be careful to use the correct version)
Now my Wallaby is up and running again! Thanks to xda-developers and Wiki and to Lumpi. There is no secret. I just did a lot of reading from the threads. It's all there. Good luck guys! Merry Christmas!

why ur wallaby resynched....
The reason it re-synched.... is because... when u go to the wallaby bootloader... and go into the GSM menu's (that allow u to tun off and on the gsm... and band tests... the key to it is there.... just reset those puppies at least 1nce.. then when u reset and boot... voila... it will sync,, but... I'm still stuck on that 1% error... rsu failed!! so.. wish me luck... oh.. btw.. when u get the 1% error it will not sync again until u repeat the process at the wallaby bootloader... so... any ideas anyone>> to get past the 1% error? I've read up and down ... searched left and right here... but no luck yet... I'm still trying what was posted here... so... wish me luck.... !!! oh... question what version is ur wallaby?? PW10A or B?

Re: why ur wallaby resynched....
r5pete said:
The reason it re-synched.... is because... when u go to the wallaby bootloader... and go into the GSM menu's (that allow u to tun off and on the gsm... and band tests... the key to it is there.... just reset those puppies at least 1nce.. then when u reset and boot... voila... it will sync,, but... I'm still stuck on that 1% error... rsu failed!! so.. wish me luck... oh.. btw.. when u get the 1% error it will not sync again until u repeat the process at the wallaby bootloader... so... any ideas anyone>> to get past the 1% error? I've read up and down ... searched left and right here... but no luck yet... I'm still trying what was posted here... so... wish me luck.... !!! oh... question what version is ur wallaby?? PW10A or B?
Click to expand...
Click to collapse
hello..
did you find a solution for 1% error? I have the same issue and I tried all night...and day...and nothing (

Reflash via SD
Hi morph751,
Firstly, thanks for this, I have now finally got my Wallaby back to a state where I can ActiveSync it, and actually run programs on the thing. Unfortunately, the RSUupgrade continually faults at the 1% mark both version 4.16 and version 4.21. The one step in your instructions that I did not follow, was the first "Download xda developers special rom and re-flash via sd card". The problem with doing this, is that when cold booting with the SD card in the slot the device simply hangs at the GSM Error screen. I have bootloader version 6.22, so I assumed this was due to the post 5.17 SD card locking. But the info and utility to bypass this doesn't seem to help either.
Is there something fundamental I am missing in terms of being able to boot the device into a mode that will allow me to flash it via SD?

By the way, when trying to flash the device via Program A, it fails with an error indicating that the power cable is not plugged into the device. The device is in the cradle, with USB connected and power connected to cradle.

OK, by folllowing the instructions at http://forum.xda-developers.com/showthread.php?t=245282, I have been able to sucessfully flash the device to XDA Developers special ROM image 1.2. But I still get Program B failing at 1%, using version 4.21. Has anyone managed to overcome this, if so how? Thanks in advance for any help.

Related

early model PH10A XDA II...ROM updating weird problem..

Here's something weird...
I have an early model PH10A XDA II...
was on ROM 0.81.00 USA
Radio: 1.05.09
Protocol: 1337.10b
Date 8-11-03
I'm trying to upgrade it to the latest i-mate ROM.
I have gotten to the point where it says "The current software is now being erased....the update should take 30 minutes." but the first time...it gave me an error and it asked me to reboot the device and try again...since then...
....it stays there for hours with no update, no errors, or feedback of any kind. All I get on the RUULog.log is "17:24:10 Connection with USB"..then nothing happens...
I have tried re-boots, hard boots, taking the battery out and waiting a few mins, making sure the battery is charged, I'm on XP and the latest Activesync 3.7.1, also I kill the wces...exe. app and still sits there..
I have tried the O2 version, the UK-02-version, himalayaupgradeut_197.exe...all to no avail...
Any other things I should attempt? I'm bootloader 0.23....
I'm still scouring the groups to see if anyone had this problem..
thanks!
re:Weird problem with early model HTC XDA II with 0.23 btldr
Thanks to these posts I can safely say I found a partial solution that works. From other similar posting, it seems the early bootloader 0.23 was a pre-release demo and not for public consumption...so this USB upgrade process does not work for this version.
What worked for me using this bootloader version was a combination of the posting here http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=93&PN=1 - using their choice #3.
1. Download ROM 1[1].72 SD.rar (ROM 1.72)
2. Extract ROM 1[1].72 SD.rar with WinRAR, you will find two files; ntrw.exe and ROM.nb1
3. Put them in any folder; say c:\ROM\
4. Go to DOS command and the folder contains the files
5. Type C:\ROM>ntrw write ROM.nb1 E: (Assume your card reader drive is E as shown in the below figure. Wait until finish writing the rom.
6. Put SD card into your XDAII, go to bootloader mode (Power + Reset + Directional Pad) and follow instruction on your device screen.
However, for this bootloader it definitely wanted a RAW formatted SD card, not a card formatted by XP/2000 card readers. I also tried other devices format Treo 600, etc...but what did the trick was to do a save to SD command using the USB/Serial program ROMUPDATE.exe located somewhere on this board.
This allowed the card to work with the bootloader...
Once this was done...I was able to insert the card on the card reader (and get an error - ingnore since it was raw format)...and type step #5.
Once this was done I was able to boot the device again.
To note..most of the solutions posted here work for public release bootloaders above 1.0...but this was an early release bootloader...and this is how you get this one to work. NOT using USB.
Now the next task is ...how do I upgrade the bootloader?
pda t-mobile mda ph10a
hi i have an old pda ph 10a ,and i want to know how to hard reset device, when i pres (power,navigation key ,and reset) mesage apears on screen says( serial v1,06) and nothing hapens
does anyone know how to reset and try to restore setings from pda (its on a german ,so that is more dificult)
removing SD card from device should solve your problem
pedjaar said:
hi i have an old pda ph 10a ,and i want to know how to hard reset device, when i pres (power,navigation key ,and reset) mesage apears on screen says( serial v1,06) and nothing hapens
does anyone know how to reset and try to restore setings from pda (its on a german ,so that is more dificult)
Click to expand...
Click to collapse
for hard reset u need not to press the navigation key just press power and reset.
and if this does not help try reinstalling the rom in boot loder mode(serial 1.06).

Have I bricked my device? Help!!!!

I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up.
Now, the phone is dead completely. I can''t even enter bootloader mode.
Is there a possible way that I can still save it??
Help!!!!
Have I bricked my device? Help plz
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up. Can't remember exactly, but like some address can't find error.
Now, the phone is dead completely. I can''t even enter bootloader mode. Only when I take out the battery and plug in the charger cable the red light comes on. I looked the upgrade problem page, my symptom doesn't match any.
Is there a possible way that I can still save it??
Help!!!!
I had something similiar happen a little while back. What I did was pull the battery out and leave it out for a while, maybe a few minutes. I then put the battery back in and held the two side buttons and hit the reset button to put me into bootloader mode. I then cabled it to my computer and flashed a new OS via mutty. That got my phone back and operational.
@float. Nuh, it didn't work on my brick. Prob i will have to take it back to Tmobile if they kind enough to repair the no warranty phone i bought on ebay.
Sorry to have opened a new thread, I was so desperate.
Plz delelte it.
how exactly did you try to update the radio using mtty?
I download the 1.27 shipped radio rom. P.S. It seemed to be a german version, not sure whether that caused the disaster.
Using NBHextract to get the single GSM.NB file, then in MTTY, typed
USB> task 32
USB> lnb GSM.NB
Before flashing, just had it upgraded to the HTC AKU3.3 OS rom only. The old version radio rom version before flashing was 1.18.
Maybe the order i flash is wrong. I flashed OS first then the radio rom.
just guessing
ok, you loaded the radio rom code where os.nb should go. That may have caused mega bad blocks in flash. Can you even get bootloader mode if you reset using Wiki directions to obtain Tri-color bootloader?
Yes. I have tried many ways wiki suggests. Such as removing the battery leaving it more than half an hour and plugging it to the usb cable without battery. still can't get to the tri-color bootloader mode. Basically, I just can't turn on the phone.
If you connect it to the computer, can it communicate w/the PC? If you hear the windows tones try opening up mtty and see if you can communicate.
i'm stuck in the same place
for me it happened during extrom flash
Try removing the battery for a bit (a few minutes, maybe half an hour). Then, put the battery back in but don't plug the usb cable in. After that, hold the two side buttons as if you're trying to get it to go into the bootloader. Hit the reset button a few times with your stylus and see if that gets you to the bootloader. That's what worked for me.
tried that
tried removing battery and connecting usb
nothing helps
is there a place that fixes tytn in belgium ?
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
diffda said:
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
Click to expand...
Click to collapse
well your not supercid... your still locked to qtek
Look here and unlock your phone before doing any flashing!
http://forum.xda-developers.com/showthread.php?t=295751
to late i ve done that tow day's ago , now the only way to make my phone back to life, PB + KITL method i think
god bless KITL

Bricked my phone i think

Hey everyone,
i am so upset and lost; words cannot describe it.
So i installed WM6 black shadow and everything was working except for SMS and MMS. So i am like ok i can live with that for a day till custel' rom will come out. SO i decided to upgrade the radio to 1.43 and boom here is where the problem started, No GSM on boot up. Phone doesn't boot up. I tried install 1.40 over again, still nothing. No i tried upgrade the the rom itself, i tired custel 2.5 and nothing and i tried the new Cingular rom, still same problem. the roms flash all the way. I read the wiki, and saw the mtty.exe thing but that doesn't work for me either. I am really lost and don't know what to do.
Specs
cingular 8525
hardspl v7 cid and sim unlocked.
PLEASE HELP
4.13?? 4.10??
Where did you download these radios from??
or do you mean 1.41 or 1.43??
Yeah thats what i meant, 1.40 and 1.43 sorry. You can see how upset i am.
Thanks Again
Well, if your phone turnes on .. it's not a brick.. lol .. it IS fixable... When you turn the phone on does it go RIGHT to the 3 colored screen?
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
If you are superCID I don't see how flashing a radio could have messed up your phone.. that's weird.
mrvanx said:
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
Click to expand...
Click to collapse
I read everything there and nothing seems to be working for me. I woudnt post for nothing. i dont want to be annoying.
OK im going to repost what ive said on 4wm:
We need to check if your Radio BL is functional, firstly leave HardSPL v7 on there and connect to the bootloader via mtty (il assume you know how to do this).
Issue the following commands and tell us the results please:
1) checkimage (this shows the CRC checksums of each component...id expect the radio image to show a timeout....
2) info 2 (This will verify that your CID is intact)
3) info 8 (does a bad block check)
Once youve done this, flash SPL 1.10.oli to the device and once again connect up to mtty.
4) 'rtask a' this will enter the radio bootloader you will see "Enter Radio Bootloader" or something to that effect
from now on when you type the text does NOT appear on the mtty screen.
5) 'rversion' this should return your radio bootloader version...now unfortunatly if you see nothing...you radio BL is dead and sorry your device is royally bricked. If you get something returned back onto the screen (most probably containing the text '0108') then your radio BL is fine.
Click to expand...
Click to collapse
do as instructed in that text, post your results here.
I cant falsh spl 1.10 oli. it gives me the 260 error.
the 260 error is not connected via USB right? .. weird... have you tried taking your battery out for a couple minutes, then booting into BL mode? sounds weird but this worked for me when I didnt flash hardSPL firsl..
hey mrvanx's
I can't downgrade the hardspl to 1.10, anyhelp.
I cant active sync, the phone doesnt boot up.
Is there anyway to aviod having to respond on the phone.
hey,
i can get the phone to boot up into windows and then it freezes within a couple min. what should i do. Still no gsm message and no phone. thanks
Dan
OK, so let's try and get you to a working state - I've bricked mine a couple of times and it can be quite heart-stopping, eh?
The first thing I would do is re-download radio 1.43, just incase your current one is damaged somehow.
Secondly, download Black Shadow - I know it's not the ROM you ultimately want but the aim here is to get you working again and we can move forward from there.
First, boot up into BootLoader mode (hold down the OK button on the left side of the phone and the power button and then press the reset button on the bottom, just in case you didn't know
You should come to the three colour screen and it should be reading IPL-1.04 and SPL-2.10.Olipro. If it isn't, stop here and post what it does say.
If it everything is OK at this point, when you plug your phone into your computer, it should change to USB at the bottom. Just wait for the Found New Hardware prompts to clear on your PC and then flash the black rom - choose the hardspl option in the flash program.
Once that has finished and it is at the "tap screen to set up windows..." bit, put it back into bootloader mode as above and flash the radio.
This should hopefully give you a running phone again as I know this combination works OK as I am currently using it.
Fingers crossed, don't panic, and let us know what the results are
Cheers,
Smiffy.
Nothing is working, can some please help me. Is there anyt way i can restore the spl to the original one so i can send the phone back, i just got it like 2 weeks ago. thanks
Also i have a bad block thats what i think makes the phone freeze after i boot it up.
How can i get around this, thats seems to be the biggest problem.
Hey everyone, let me give you more info.
I can fully flash any rom and and radio,
phone will boot up like 1 out of 10 times and then freezes and thats it.
i have a bad block number 6. I have hard spl v7 installed before the phone got screwed up. I cant downgrader the spl to a lower one to check if radio stack is screwed up. Can someone please help me, if you need to ask me more info feel free.

stuck in boot loader updating to 1.43 on black shadow

I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.

HardSPL won't succeed

Hi All,
I'm new to the PDA-world and the Hermes. I'm trying to Hard SPL my Hermes, but it fails everytime.
When I run 2.10 - Hard-SPL-V7, it kills activesync and my connection is lost and I get always the message "error 260, Update error".
I have the latest framework edition and tried it on 3 pc's (1 Vista, 2 XP)...
What am I doing wrong?
Hope somebody can help me....
Kind Regards,
Micha
1). dont connect to active sync. open active sync and untick "allow usb connections".
2). put hermes into bootloader and connect to usb.
3). run ruu_wrapper.exe
should update to hard spl....
dont forget to tick "allow usb connections" again or you wnot be able to sync..
error 260 is an open port error.
if you wish to flash new os would advise to use sd card method. its safer than using the computer. just make sure you have greater than 50% battery power. happy flashing
Thnx, will give it a try.
First I have to flash HardSPL before I can flash a new OS, don't I?
yep, sorry, should have said run the ruu_wrapper for hard spl. My bad...
im having the same problem. I also tried the way ultramag recommended but i also received the same ending. After time i try i get the Error 260 Update error. Im running SPL 2.04 and the HTC WM6 rom from the HTC website. Does any one know what the problem is?
ultramag69 said:
2). put hermes into bootloader and connect to usb.
Click to expand...
Click to collapse
NOOOOO, that won't work, you need the SSPL to deploy to the phone, if you're running stock HTC bootloader this won't work at all, otherwise we'd have no need for Hard-SPL
hey olipro, then how would i fix this. Im running the stock rom from the HTC website with no hacks. Im trying to load PDA Corners V9 rom. Any ideas on how to fix? thanks!
Take a peek at the guide i wrote about updating the hardspl. Theres some explanation about why we need to use SSPL and the procedures.
http://www.mrvanx.org/hermes_guide/hardspl
thats the guide i used. it still gives me the error. I even unchecked "allow connections" cause i read somewhere that that would help.
i did this two days ago on my phone, im running windows vista on my home laptop and got any number of errors and problems trying to do it via sync with the phone (even after reading the vista troubleshooter, with the drivers etc)
What i ended up using was the memory card upgrade, dump the file onto the memory card and go into bootloader with the card installed.
worked fine doing that way, maybe less risky as there is no chance of the usb cable coming out.
just make sure you have a good battery charge on the phone.
Help Help Help w bricked 8525
I got into this position trying to upgrade WM5 to WM6 from HTC site.
Process got to 20% and just stayed there.
I reconnected usb cable and got a vendor id error
Then I get the Error [260]: CONNECTION
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
I believe this is the bootloader? I have downloaded RUU_signed.nbh, renamed it to hermimg.nbh, installed on root of my SD card and held OK, soft reset and power button:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
All post indicate that the device can be reflashed and have the OS reinstalled. I can't get there from here.
Can anyone please help?
blackdog9692 said:
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
Click to expand...
Click to collapse
How big is your SD card? Flashing only works with cards <2GB. Also, sometimes certain cards just don't work for flashing, and just swapping to a different card fixes the problem.
I assume you searched the wiki, and found the relevant pages on the Hermes (including SD Card Flashing and other things about flashing/upgrading) there?
Still Lost
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen. When i attempt to flash the rom via PC to WM5 or WM6 i get the Error 260, i also get a vendor ID error sometimes.
How can i find the key 8525 thread that i am told has the answer to my delima? I keep picking up bits and pieces but am missing some key steps and tips.
blackdog9692 said:
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen.
Click to expand...
Click to collapse
That sounds like the SD card is formatted incorrectly. Make sure it's formatted using fat32, nothing else will work.
Still not there from here
Thanks for your help. Before I formatted the SD FAT32, nothing would happen doing the bootloader reset. OK/ON/reset button.
After format and only the hermimg.nbh file renamed as indicated, I then get what looks like the loading process but back to the bootloader screen.
Q1: This is an AT&T 8525, it was perfectly fine before failure from WM5 to WM6 (process froze at 20%), what is the RUU file that I need to put on SD??
Q2: After "Loading ..." I try the WM5 PC upgrade of ROM via USB cable, I get the load process to appear to work but it gets to 1% and the phone reboots and the PC reports error [294]: Invalid vendor ID. If I do this again I will get the Error [260]. Ive repeated the process several times.
Is this the normal course to take or should the "SD Method" (with the WM5 or WM6 RUU.. file) complete the process to a working OS?
Q3: Is my situation hopeless? ATT will take my out of warrantee 8525 and reflash for $129. Reading the threads it seems that like me this can be done by me, this is my desire.
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
The newbe guide has been off line. I will look again. Is there a single place to read about "radio PDAs and the 8525 and understand the software build and custom options?
Sy for the long post. But still want to fix if possible or I will be force to mail in for ATT repair.
Thank you all.
blackdog9692 said:
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
Click to expand...
Click to collapse
Oh boy, you haven't installed HardSPL? You are walking a bit of a line there mate...
HardSPL is a custom boot loader that makes bricking your phone when flashing much harder to do, and helps large amounts in the recovery process if you phone does brick.
Does the phone boot at this point? If so, do not try flashing the phone again. Go get a copy of HardSPL and install it, then try flashing from the SD.
I still wonder why people didn't read before bricking...
Anyway, you should start reading now and wiki is your friend. Your SPL is 2.03, so look at the bottom of the page (there is only one solution till now, so good luck with that):
Code:
1. Boot OS using KITL+PB
2. Do no disconnect your HERMES till the end of the step 6
3. Download SSPL on HERMES by wifi from ie explorer
4. Launch SSPL then flash Hard-SPL from your computer
5. Put your hermes in bootloader mode
6. Flash any radio in NBH format from your computer
Still researching and working this bricked 8525
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
I then put it on an SD card and held the keys and reset. The device displayed a white screen and "Loading..." appeared. Afterward the 8525 returned to the stipped boat loader screen and that is where I am now.
Some of the help i receive and read on wiki threads has me confused with what to do next and how "exactly" to do it.
It does seem that I am not alone and people have fixed their phones and the process to do this is on the forum. I'm just still missing something.
Help me further if u can.
Thank you.
blackdog9692 said:
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
Click to expand...
Click to collapse
FYI: bad form to PM someone and post the same thing here. Keep it in the thread so others can be helped as well.
As I replied in the PM, if I'm understanding your post correctly, the phone boots to the tri-colour screen?
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
jdc said:
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
Click to expand...
Click to collapse
We already know that the phone is without HardSPL, according:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
Click to expand...
Click to collapse
There is small chance (read my previous post) to unbrick device with SPL2.03 so better try to get this back from where you take it.
And please, change topic, because this brick isn't HardSPL fault at all.
Edit: oh dear, it's even not your topic ...good game, I'm off

Categories

Resources