I have a big problem. Yesterday I tried to upgrade my atom to the latest rom. Everything went ok up to 22 %, then my Atom rebooted and after that my Atom can’t boot up. The screen is black and the only thing that happens when you try to turn it on is that the Atom starts to vibrate. I have tried to soft reset, hard reset and boot to bootloader but nothing happens.
Does anybody have an idea of what I can do to start my Atom?
/D
Dead Atom
Try this
Remove battery and sd card. Leave it for sometime say about half an hour.
After that while pressing camera button+soft reset insert battery after 5 sec release soft reset, keep holding camera button. Atom should go to boot loader.
Connect to usb and run upgrade.
same problem
while flashing rom got reboot after that i don't even get the startup logo of o2
while connecting it 2 pc usb cable orange led show it is charging but no display plz hlp
same problem
check your battery pack . If your battery is dead the Atom Life act the same way as U describe - LED show charge and black screen. Have been there, when battery is replaced it is working fine again.
Related
Hi all....i'm totally new at this PDA stuff.
Just bought atom pure, and I wanted to add some useful softs into it.
When the atom still plugged into USB, I push the reset hole and suddenly..DEAD
It wont turned on again when I push the power button. Already try to hard reset and still dead, Already try to take battery for while and still wont turn on.
Please help me guys!!
i have tried install chiense wm5 3.5.2 akuu and now my boot loader dont workin first says usb error and i tried try instal new one boot loader with memory stick but now bootloader totaly crashed no workin no cant see colores screen
i have tried found in forum but a lot topic
and sorry for low english
1. take out yr battery from yr atom for about 1 minute
2. press the camera button and the reset
3. load the AKU 3.3.3 or the original O2 atom software
Violalie.. and waiting for 20 to 30 minutes as it will flash.. Good Luck mate.
dude thx for info but it didint work i did take out battery sim card and memory card 12 hour still cant enter boot load only a black screen comin and goin
Try the following:
For those of you who have downloaded and flashed using SD Card method who ended up in a brick! ITEX recovers his Atom by following procedure:
1. remove SD Card
2. remove battery
3. hold camera button and reset (stylus) button
4. replace battery while still holding the buttons
This will bring you back to bootloader mode.
Taken from http://forum.xda-developers.com/showthread.php?t=314613
ehm didint work what should i do
can i change bios my atom
Your bootloader was destroyed and you can only send your device to service.
1) your devices can boot up and use well?
2) did you mean that even if you try to hard reset your devices, it wont goes to boot loader mode?
3) PC cannot detect your hardware when you goes to boot loader mode / WM5 mode?
Did u try copying aku 3.3.3 image file in memory card and try boot loading?..
no i didnt try because my boat loader no workin cam+reset and volume+rec+reset dont working i cant load anything
Remove Battery
press power + Joystick + Reset(Stylus) then place the battery ??..
Normally i press Power+Joystic+Reset(Stylus) to go into bootloader.
If you closely read AKU 3.3.3 thread.. there is one place you can see methods to bootup Bricked ATOM.. try page 78 onwards??
Thanks.
Remove Battery
press power + Joystick + Reset(Stylus) then place the battery ??..
Normally i press Power+Joystic+Reset(Stylus) to go into bootloader.
If you closely read AKU 3.3.3 thread.. there is one place you can see methods to bootup Bricked ATOM.. try page 78 onwards??
Thanks
Click to expand...
Click to collapse
dude its only resetting phone taking factoty settings no i didint i am readin now
when i remove battery and wait a while and put it back orange led ligthing one time its mean my brick not fail totaly ?
vhd99 said:
when i remove battery and wait a while and put it back orange led ligthing one time its mean my brick not fail totaly ?
Click to expand...
Click to collapse
Your atom is still live.. check out below thread .. how they recover a dead atom..
http://forum.xda-developers.com/showthread.php?t=314613&page=76
http://forum.xda-developers.com/showthread.php?t=314613&page=77
http://forum.xda-developers.com/showthread.php?t=314613&page=78
what mean hard reset
ok i got what hard reset i did hard reset but still no goin boot loadin i tried all methods
It's NOT hard Reset.
1) Remove the battery for at least 1 min.
2) Take back the battery in
3) Press the Camera Button following with the pin hole(reset button)
i erased boot by misyake any body help me how to restor boot device now fully dead
just orange led when i plug usb
You should search the forums first, however, this might help http://forum.xda-developers.com/showthread.php?t=331818&page=2
thx mate for replay
but not help coz device totaly dead anad dont enter boot loader
abcrino50
Use JTAG cable and JFLASHMM software to restore bootloader.
And learn russian Boys from 4pda.ru already restored their bootloaders.
PLEASE LEARN TO READ THE WIKI PAGE...after reading this , last resort is the forum
http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK
Your device is bricked, if and only if, your device won't start normally... even if you press soft-reset, hard-reset, or even bootloader mode buttons. Usually a brick is caused by improper ROM upgrade, and using tools that modify the ROM. Before panicking, do the following:
Brick Test:
1. Make sure your device has ample battery charge. If you're not sure plug it in with the wall charger for at least 10min
2. Remove your battery for at least 1 minute
3. Replace your battery while observing the LED lights
4. If the LED blinks once upon battery insertion, you might have hope yet
The only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding the buttons
4. Release the buttons at the same time (You should see bootloader screen)
Note: Failure to hold the buttons at the same time during battery insertion will cause it not to work.
----------------------------------------------
If nothing HAPPENED after this trial of revival, your atom MAYBE BRICKED/forever dead.
If there is no LED LIGHT on ur atom, YOUR ATOM IS BRICKED.
sorry my friend, your phone is a paperweight NOW if this is the situation.
LAST RESORT: O2 service center, ur lucky if they have support in ur country. but the price for fixing (if not under warranty)...mmmm a new iphone ;-)
abcrino50 said:
i erased boot by misyake any body help me how to restor boot device now fully dead
just orange led when i plug usb
Click to expand...
Click to collapse
abcrino50
Please read
http://forum.xda-developers.com/showthread.php?t=336278
and waiting 1-3 days
MY HP6815 IS DIED.
I was flashing with the good wm5 rom of NHOCBANME when the phone fell to the ground and has detached the battery!!!
My hp 6815 is off and doesn't turn on.
I tried to flash by ordinary mode but the phone is always off.
Only battery led is on if the phone is charging.
I think it is permanently damaged.
Can someone help me?
Test:
1 - Remove the batery...wait some secounds
2 - Put the batery back on it
3 - Press POWER
4 - Press RESET with stylus and press the 2 softkeys (the keys that are on top of the red and green buttons)
5 - The phone will enter flash mode
6 - Use software to re-flash or use SD card to do it(SD card option: card must be inside when you do this!)
The same thing happened to me... but i lifted the cell and there was no cover in the battery...
hope this helps...
Dead boot ?
Hello,
I have a same problem after flashing. No life in my 6815.
The LED used to blink orange when charging or usb connected but now it flashes orange-green. Does anyone know how i need to fix my boot with jtag or other fix?
Many thanks
A free TUROK game[Newest turok game out last year] for whoever helps me fix my bootup. Game is boxed, manual etc.
Thanks to GraeFNZ (and helloworld1)...This is the correct procedure:
" How to recover from semi-brick state:
1. Prepare a sd card with proper diskimg.nb0.
2. Pull out the batter for a few minutes.
3. Press and hold two "-" button and at the same time, put the battery in.
4. Wait a few second and release the button, then after a while, the device will be in bootloader mode. "
I have the same problem with 6815
Hello, I'm new to this forum I have problem with 6815, it's completly dead after trying to put wm 6.5 on it. I have tried to pull out battery, to put it back, to press "-" keys, to reset... but no succes. It's dead. Battery is fully charged. It's showing charging status when I conect it to the charger or USB PC port. Anyone, please help, doing it for a 2 days, my head and stomach are ruin...
PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!