I'm searching for a metal case for my new hermes. Anybody found one yet?
I tried it on ebay, but there are aluminium cases for wizard only.
signal killer
May I suggest that you don't buy a metal case for your Hermes. I am a long time Wizard owner (looking to buy a Hermes as soon as I can). I have had an aluminum case and always wondered what was killing my signal. If you do a search over in the Wizard forums you will see that those cases just kill your signal. Maybe the Hermes has some improvements, but I would be careful. Just thought I would save you from some frustration (and maybe some wasted money!) It's a shame, cause I love those cases as well.
Anyone found an aluminum case that would work yet? I have always hated leather cases never used an aluminum one, I just know I am gonna tear the screen up if I dont have something hard rotecting it while its in my pocket, basically I would be usin it in a manner like somebody would a sunglasses case, take it out when its in use, and put it back when its not..etc, and I'm not that important, if I miss a call due to bad signal, its no biggie.
Indeed. Aluminium does a good job of absorbing radiation. Sadly GSM is affected by it as well.
Well I haven't seen that at all with the Vario I get the same signal wether I have the case or not
Really? Vario was... a.... Wizard, was it?
Aye
You can find aluminium cases (silver or black) for the TyTN at www.pdair.com
i just received my PDAir aluminium case, it makes the device looks thicker. but at least u wont have to worry about cracking the LCD screen!
my previous ipaq pda and verizon vx6600 got LCD screen cracked due to sitting on it. i dont like to wear it on the belt, i like to put the pdaPhone in the pocket
I just received my aluminium case too. Here is a little information and some pictures I can provide.
http://www.wretch.cc/blog/doomer&article_id=4597663
I'd be very interested in any subjective assesments of the impact on signal strength, and battery life, as a result of using one of these cases.
I'd like one, but not if it significantly hampers the signal, or substantially drains the battery as a result of a need to run at higher transmission strength.
Until now ( exceed 12 hrs ), I didn't find any signal reduction. I have no problems calling out and accepting incoming calls while my hermes still wearing alumium case all the time.
I got mine PDAir case a couple of days ago. No reall problems really. nicely made, looks good (black one), and the belt clip is pretty good. Only one droped call, but I had one or two droped calls from home without the case, so I don't think it is the case. Overall I would recommend it.
If I get time over the weekend, I might post some hi rez photos of the black case with the Orange SPV 3100.
Ordered and received the black version from PDAir, I had ordered the invisible shield first, so my TyTN fit a bit too tight in the aluminum case cause of the shield..but it went in.
I am currently using this sucker so much that I really didn't like to have to flip the case open all the time to use it, I debated on removing the plastic window from the case, but just opted to throw it on the shelf within the first 15 minutes of opening the package.
I didt use it long enough to notice battery drain, but the signal strength was the same with or without the case, also the case hinges on the right hand side to allow it to remain in the case while using the keyboard..but it feels a bit weird, almost like its designed for a left handed person...hard to explain.
Well, I have had mine for about a week and I will say this,... THANK GOD! as I have dropped it since I've had the case and well,... IT WORKS!!!
I can get to all of the buttons AND even the antenna, it also ascut out for my lanyard that I use. Everything is accessable including the microSD card (why I don't know). It is a little difficult to get to some of the buttons with my big "sausage" fingers but it still serves the purpose that I need.
Unless I find a better case (which I haven't seen plans for) I sticking with this one.
PDAIR Great job!
I dropped my Tytn off the couch a few times after passin out while hangin out on IRC, the invisible shield worked very well...but I decided I would give the aluminum case another go..I removed the clear window and then thought the black case looked crappy around the silver phone, so I started to sand it down to polish it, I got all of the front cover sanded and part of the back, and went to see how it looked around the phone...I just held the phone and positioned the top cover over it, and then I noticed the screen flicker...I'm not sure if I missed this before I sanded it, because then I checked with different wallpapers and its not really noticeable with some and it only happens when the case is over it...kinda strange I thought, considering the phone has an aluminum bezel already around the screen from the factory, and I also did notice I would drop a bar on the signal if I wasn't in a strong area.
As many people making aftermarket stuff out of carbon fiber nowdays...I can't believe someone hasn't started making them for phone's/pda's
Its relatively cheap, and a lazy route of making them could be done by just vacuum forming one from an already made aluminum case.
What about Bluetooth? Does aluminium case shields it signal?
Got a black aluminium case from Boxwave. Looks and fits fine. Didn't notice any Bluetooth signal degradation so far.
BTW PDAir and Boxwave cases look identical - most likely both have the same OEM producer.
Got my aluminum case from dealone.com
Had my case since day two with my Cingy 8525. No problems noted, glad I have extra protection as I'm always bumping into things walking. Tables, chairs, etc. Mine is the monaco aluminum case in black. Absolutely love it!
http://www.amazon.com/Cingular-8525...s_sr_2/002-9456356-4411227?ie=UTF8&s=wireless
Just order 1 from there.
Related
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Thanks for the review! I bought the same case a few months ago, although it was advertised as for the Verizon Touch Pro 2. I was unaware they made one for the Tilt 2. Now I won't have to worry about it falling off randomly!
thsi case probably wouldnt work with invisible shield on too huh
Doinshots said:
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Click to expand...
Click to collapse
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
JJHiemenz said:
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Click to expand...
Click to collapse
Man, sorry you had so many issues. The PTT button is indeed covered, but she has had no issues with it at all (hers is remapped to toggle bluetooth on and off). The fit on the screen portion is *very* tight. Took some effort to get it installed properly.
Also, mine definitely said "Tilt 2" on the packaging.
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
sleze said:
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Click to expand...
Click to collapse
Nope, the PTT button still works perfectly under the cover. Does not get accidentally pressed and is responsive when you push it.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
Sounds like skinning/shielding your phone with GadgetShieldz might be the way to go. The GadgetShieldz does take a little time to install but it works. The protective film on the screen is easy to install and bubble free. It makes the phone non-slippery. It would not protect the phone like a case but it does prevent scratches. When installed, it adds very little weight and dimension to the phone.
Actually, there are other protective films/shields but I only have experience with GadgetShieldZ. It might work for you.
Boxwave Praetorian Crystal Slip for Tilt 2
orb3000 said:
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
Click to expand...
Click to collapse
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
I wish I'd seen your post sooner! Home Depot and Lowe's does indeed have something like that. I'm sure lots of hardware stores do. It's called Plasti-Dip. I have a can right here You can buy it as spray-on or dip/brush-on applications. I use it on mountain bike parts and tools for extra grip. I'm not positive how well it will stick to a slick plastic surface but it is an option.
BluEyedTiger said:
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
Click to expand...
Click to collapse
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
It's held up quiet nice...even with as much flashing I do (have to remove the bottom piece every time). I've figured out a great way to put it back on that's really fast and easy. Some people say it's difficult to get on. I think the top piece is the hard part but I've taken it off a few times and have no issues there either. It still fits good. If I remember, next time I take it off I'll shoot some pics of how I put it on and upload them.
Learic said:
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
Click to expand...
Click to collapse
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
BluEyedTiger said:
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
Click to expand...
Click to collapse
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Learic said:
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Click to expand...
Click to collapse
Yeah I got mine directly from boxwave. They have like 3 different models of that slip. Most of the adds I saw on Amazon and eBay claimed it would fit on 3 or 4 different TP2 models which I knew it wouldn't. I emailed boxwave about the pics in their online catalog because it didn't look like a Tilt 2 to me and they admitted it wasn't. They said they didn't have one for the pics. Which made sense I mean why spend that much just to get pics but they promised it would fit so I figured what the hell. The hard covers kinda suck.
Thanks for the replies, I guess I will go ahead and order it and see what happens.
I just got the unbranded version of this case off ebay (the seller's id was e-story).
It's not too bad on my unbranded TP2. It's slightly more difficult to slide out the keyboard, and when the screen is fully tilted, the top row of keys are slightly obscured, but nothing too major in my opinion.
I like that the case improves the grip of the phone, but I'm also rather concerned that the case will eventually melt under hotter conditions since the material feels rather gummy.
Overall I've really liked my Defender--I just found a "new" feature where the belt clip can stay open for even MORE kickstand options!--but it's a little bulky, the battery is a ***** to remove, and already, even though I've been very careful with the case (barely left the house since I bought it since I've been home studying all day!) there are noticeable white "specks" on the screen and the bottom latch that holds the two plastic pieces together has broken somewhat!
Again, I've loved the protection (though one last thing that bugs me is how the screen protector is cut a hair too low at the top). Think Best Buy will honor the return, no questions asked, etc? I've still got the receipt, box, etc., and it's within the return period (30 days).
Thanks for any advice, including alternate great-protection cases with less bulk and/or easier to take off to do a battery pull!
Panamaniac
PS: the "speck" is out of focus, sorry. There are several like this that I can't seem to remove. Cant even tell if they're on the inside, outside, are a scratch, or what!!
The only complaint I really have is the height of the case next to the screen. It makes hitting those corners on the touchscreen too difficult.
Other than that, I have been pleasantly surprised. I will still probably switch it out when the Kraken II or Ballistic is unleashed.
Yes best buy will let you return it the otterbox defender rip off my invisible shield and best buy was like o sorry and she returned it
yeah the will. I returned mine with some nicks on it and they took no questions asked. I really dont need that much protection right now..once I start my job again then I will pick it up until then im rocking a TPU case and it works amazing. Ive dropped my phone onto my houses doorway edge and nothing was hurt or broken.
Ya touching the sides is difficult at times, and that's been annoying.
Thanks for the info on easy returns, I might do just that...
Snarebum, when you say TPU, I know that refers to a certain material (the fake silicone stuff right), but do you also mean a super-cheap one or what? what case did you get?
they are not super cheap material as far as I can tell..
heres the one I bought and I absolutely love it!
http://www.amazon.com/TPU-Cases-Flexible-Sprint-Retail-Packaging/dp/B0053NWDO0/ref=sr_1_1?ie=UTF8&qid=1310786932&sr=8-1
Im prolly going to get his name wrong but OneStepAhead on here makes them. thats who I ordered mine from.
heres his website: http://tpu-cases.com/index.php?main_page=index&cPath=7
Does anyone have experience with this case? I know it covers the mic (I plan to drill a little hole).
I just received mine today and I must say I'm very impressed by the quality of the mold they used. Meterial seems top notch. Love this case so far, they also included the new screen protector which is a plus. Ill get pictures up ASAP. I would definetly recommend this case to anyone with an s2.
Sent from my SAMSUNG-SGH-I777 using xda premium
Pictures would be great! I also have a white one on the way, hopefully as I placed an order over the weekend. I intended on modding the thing to get rid/fill in the antenna hole if I ever find the time, too (or find out if it really bothers me that much).
Ok, whats the deal with the corner cutout? I've seen this on several different cases. Does the international version have some sort of pullout antenna?
Case looks nice and classy but for what they are charging they should be offering a case that's specific to the AT&T model.
I recall reading that the corner cutouts are originally for Korean model phones. The antenna was in that area for those phones.
I really like it. It's a nice mix of hard and soft materials. It's flexible, which is nice because it makes removing the case fairly easy (for those of you who want to access the phone's back cover to hot swap batteries).
For the most part, the case feels pretty smooth, which makes getting it out of the pocket an easy process (I previously used the casemate pop case and the rubber sides made it fairly annoying to pull the phone out of the pocket). The case definitely adds more grip to the phone, but overall, it still is a little bit on the slippery side. On the continuum of "slippery vs. grippy" I'd say it's a pretty good balance, but I wouldn't mind it being a little more grippy.
Even though the case is made for the international GS2, it still fits well on the AT&T SG2. The noise-cancelling mic is covered by the case, but I have not had any problems as a result of this. However, you might come into problems if you are trying to use the phone in a noisy environment. I'm a little bothered by the corner cutout for the antennae (for the international SG2) since it really leaves that corner unprotected if the phone happened to fall right on that corner. Then again, i'm just going to take my chances that i'm not going to drop my phone on that exact corner.
The case still keeps the phone very thin and sleek. Also, the case has these tiny sparkle dots that show up on the back of the case, which give off a cool effect when reflecting light. Some may say, they make the case look a little feminine, but I personally don't think they do. In all honesty, you can't even really notice them unless you look close at the case and in the right lighting.
I got the yellow ultra capsule. I've heard one person say that these cases are prone for showing up finger smudges, but at least with my yellow one, finger smudges have not been a problem.
The case covers the volume and power keys. They are still pressable and work fine, but the buttons aren't as sensitive as they are without the case. However, this difference is really negligible for me. Overall, hardware buttons work fine.
I really liked the Body Glove Mirage cases that were made for the Samsung Captivate and the Infuse. In my opinion, this case is just as good as those cases.
can you guys post some pictures? want to see how much it adds to the thickness of the phone.
it does look good from their website though..
Sorry on the delay for the pictures guys, let me know if you need any certain perspectives on some more pictures.
djoutrages said:
Sorry on the delay for the pictures guys, let me know if you need any certain perspectives on some more pictures.
Click to expand...
Click to collapse
what does the unprotected corner look like with that case?
hey guys like the thread title states I'm looking for a bumper. I recently got an Aluminum one I found here on xda and I'm incredibly happy I can finally have some sort of a case on with my extended battery but it impacts the gps on my phone enough where I'd like to find a replacement. Upon further reading have found a couple threads about bumpers with some that I really like but they all seem to have the cutout to fit an antenna in the corner which I hear apparently the chinese version of the s2 has. The aluminum bumper I have now does not have such a cut out. I'd like to basically find a bumper exactly like this one (http://www.spigen.com/cell-phone/sa...sung-galaxy-s2-case-neo-hybrid-ex-series.html) but without the hole in the corner. I'll probably just end up ordering that bumper anyways but any help would be much appreciated. =D
Which case do you have now? I got a ikuba bumber case and my gps is fine.
I am using the bumper shown in this post (http://forum.xda-developers.com/showthread.php?t=1417661) If you look there are pictures in that thread ,some posted by me, which show that it lacks the antenna hole the plastic/silicone case I linked in my OP has. I can't seem to get a good lock on my gps after putting it on. Sometimes it works sometimes it doesn't but either way it takes too long to make it worth it. I don't think it blocks the gps waves only impairs or bounces them a bit, I think this because before putting it on when I opened the google maps app it would say "accurate up to ten meters" or "accurate up to 5 meters" now it usually says "accurate up to 30 meters" sometimes even "accurate up to 50 meters". This wouldn't bother me but when I switch it to gps mode so it actually gives me directions as I drive it just says "lookiung for gps" on the bottom for a full minute sometimes more sometimes not moving from this screen at all. Maybe the case is not really made of alluminum because it's cheaper to manufacture other metals in china. (the case I'm using was shipped from and presumably made in china) I'm guessing from the lack of response that I'm probably going to have to deal with the antenna hole, I was really hoping for a US manufacturer maybe that doesn't cater to Chinese phone models.
The one I'm using now signal for indoor is around 40feets and out door its around 30 feet.
so much trouble just to get the back of the phone white...
eortizr said:
so much trouble just to get the back of the phone white...
Click to expand...
Click to collapse
Who's trying to get the back of their phone white?
Sent from my graphing calculator using sheer force of will
I just ordered one off eBay. Aluminum alloy bumper with tripod hole. Plan to do a review once I reach my 10 posts. can't even provide a linky yet, but it's sold by rpas5404. It's for the i9100, but I'm quite sure it'll fit. I have the i777.
This bumper does have the corner cut out, I just realized. But that doesn't bother me.
I had an amazon gift card to use up, and we're planning a road trip to a waterpark so I decided to use the gift card to try and find a waterproof/water-resistant solution for my lte. I wasn't going swimming with these, but I did want to protect my phone from the the occasional dunk or splash, and I didn't trust a ziplock bag to do the job. I also didn't want to spend a lot (otherwise I would have gotten the overboard case).
I ended up ordering the following cases;
BestDealUSA Waterproof Underwater Pouch Dry Bag Pack Case Cover for Cell Phone PDA Blue - $2.96
Waterproof Case for Apple iPhone 4, 4S - Also Works with iPod Touch, iPhone 3G, 3GS, & Other Smartphones - IPX8 Certified to 100 Feet - $4.57
Universal Waterproof Bag Case for Cell Phone / PDA, Blue - $0.01
Universal Waterproof Bag Case for Cell Phone / PDA, Black - $1.92
BestDealUSA Waterproof Underwater Pouch Dry Bag Pack Case Cover for Cell Phone PDA Blue
The plastic material seems strong on this case, and the seal seems like it would do a good job to keep the moisture out. The evo slides in and out easily, even with a tpu case, although it does it need to go in upside down if you want to take pictures - otherwise the camera is blocked by the opaque section of plastic, but this is not a big deal. There is a raised seal around the window of clear plastic (which takes up about 4/5ths of the phone screen) that makes pulling the unlock ring a little difficult, but not impossible. This is the biggest of the cases, with the most space around the phone. Screen responsiveness through the plastic is good, and the the window is clear, so its easy to see the phone screen. Lanyard runs through the width of the case, and seems very strong - I don't see it snapping or anything.
Waterproof Case for Apple iPhone 4, 4S - Also Works with iPod Touch, iPhone 3G, 3GS, & Other Smartphones - IPX8 Certified to 100 Feet
This one looks very similar to the higher priced overboard case and has great reviews. The areas surrounding the clear windows are puffy, as if it would allow the case to float. Unlike the other cases (which use a combination of two ziplock-type closure zips), this one has a plastic mechanical mechanism to squeeze and hold the opening shut like a vise. I don't know if I would trust this case to remain underwater for any length of time. It doesn't seem to seal as well as I would like, although the reviews all rave about how watertight it is. Having said that, the phone fits in this case perfectly with the tpu case, and even better without a case (upside down again), without being too snug, and the clear windows are exactly the size of the phone screen - only the capacitive buttons are hidden. Screen responsiveness through the plastic is good, and the the window is clear, so its easy to see the phone screen. The puffy areas around the clear screen also do a really good job of holding the phone in place, but makes it a bit difficult to press the power button. The lanyard that this case with end in what appears to be a thread that you loop through an opening in the case and seems like a good tug would snap it off.
Universal Waterproof Bag Case for Cell Phone / PDA, Black/Blue
I was only going to get the black one, but when I saw the blue one for a penny, I decided why not. These are identical cases, but one is black, and one is blue. These are the snuggest cases, and its a challenge to get the phone in, even without the tpu case. The plastic material the cases are made of is very tacky on the inside, so the phone tends to get stuck when you put it in or take it out. The plastic also seems thinner on these than the other cases, and the seals around the edge don't seem very reliable. Once the phone is in though, it's the most compact and pocketable of all of the cases. These cases do not have a clear window on both sides, so if you want to use the camera, then the phone screen will be covered by the translucent side of the case. It's not too bad, and the screen is still visible, but in bright situations, this could be an issue. Having said that, screen responsiveness is very good with these cases, most likely due to the thinness of the plastic. Lanyard goes through hole in the case and seems strong enough. These also come with an arm band that may fit you if you have the arms of a small child. They're really, really small.
Final thoughts - All of these would probably do a good job to keep water and moisture off of the phone (or even sand if you're going to the beach), and I think any of them would be fine to protect against accidental splashing. If I was going diving or swimming with my phone, I would probably shell out the extra cash for the overboard, or at least do some serious waterproof testing on these first. As it stands, I think I'll end up using the first case - Not too crazy about the blue, but I think it will do the best job of keeping the phone dry, and I won't need to worry about going down the log flume with it in my pocket or around my neck (like a tourist, lol).
Hey man, thanks for the reviews. I didn't even know you could get waterproof cases/bags so cheap.
I'll have to pick one up now.
I do suggest you update the prices in your post to include the shipping though for a better cost comparison (even though the difference here is minimal). So many venders inflate the shipping to make up the difference for a $0.01 item.
p.s. I'm going to pick up the first one as well since it looks like I can easily have it in my pocket as a just in case. (I'm in Florida and we have crazy torrential thunderstorms out of no where, so if I'm out jogging, I can have it in my pocket just in case.
Though expensive, Lifeproof cases are really nice. Ive known many people to go out in the ocean and take pictures under water with them.
Just an update, I did end up using that first case, and although it never went underwater, it got splashed on alot. Phone stayed dry, it fit great in the bathing suit pocket, and even took some great pics through the case. Would definitely recommend.
Quick update from me too. I ended up ordering this case: http://www.amazon.com/gp/product/B0058NXWPY/ref=oh_details_o02_s00_i00
Used on a canoe trip. The canoe flipped and it went underwater for around a minute or so, and air dried after, did a great job. Would recommend this one!
i am using the first case, blue, as well. Works fine, keeps my phone dry in a 10ft deep pool. Takes picture fine too. Thanks for the review OP.
I actually prefer these right here. They come in different sizes I prefer the 6-1/2 x 3-1/4I can't confirm they work in 100 ft of water because I have no reason to be that deep ever in my life, but for the average rainy day, screwing around by the pool or working out these work great. The best part is the patented purple zip technology that lets you visibly confirm the case is sealed. Also pics turn out great. Good luck in your decision
Asadullah said:
I actually prefer these right here. They come in different sizes I prefer the 6-1/2 x 3-1/4I can't confirm they work in 100 ft of water because I have no reason to be that deep ever in my life, but for the average rainy day, screwing around by the pool or working out these work great. The best part is the patented purple zip technology that lets you visibly confirm the case is sealed. Also pics turn out great. Good luck in your decision
Click to expand...
Click to collapse
Hahaha that had me laughing so much once I read the whole thing then clicked on the link. Good one!
Sent from my EVO using xda premium