Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
Related
Hi,
I did the popular mistake, tried to unlock with Universal Unlocker , thinking that this is the staff to unlock all the HTC phones.
Ok. What I have now:
NO GSM - we know that
Tried to install radio roms from here, nothing. I got the information about "Checking the information...." and it is hanging like this.
I made reser and HARD RESET aswell.
I tried to install a lot. Nothing helped.
I had radio ver. 1.05.... I remember that. I have my phone from T-Mobile from UK. I had everything nice, now I have four stripes - RED GREEN BLUE and WHITE and ther is written:
HERM300
IPL-1.01
HERM300
SPL-1.04
Can anybody help me ? I tried to download mtty.exe and put all the commands (not PASTE and it still not working.
Now is 6am in Lisbon. I was sitting all that night and I am finishing writting this post.
Help if you can, regards.
Ben
Have a look on this topic http://forum.xda-developers.com/showthread.php?t=280733
It did not help. Where I can get this Qtek rom ? Is that OK for my device ? I have VARIO II from T-Mobile.
I woul like to try instal this - DUMPED English ROM from TMobile Vario II from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_DumpedRoms
but i dont now how. There are 3 .raw files, how to put them to my phone ?
That solution didnt help: http://forum.xda-developers.com/showthread.php?t=280733
What else I can do ? I was trying with QTEK rom and a got white screen on the phone and 0% on the computer. It was hanging. I tried 5 times. Then I tried to install the Radio Rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
I choosed all of them. Nothing. All of them are hanging on:
Chencking the information on your device... Please wait..
Then there is a screen to update. After long time. So when I press the button is still the same info. Checking the information on your device... Please wait..
And its hanging. When I reset to bootloader again the soft telling me:
This ROM Upgrade Utility does not design for your device.
Please get probper ROM Upgrade Utility and try again!
Where can I get the radio version 1.05 for T-Mobile Vario II ???????????
Is there possibility to download from somewhere ?
Or maybe I should try other solution ?
Read "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Yes, I was tying point 5 few times. The problem is, I can connect through mtty.exe without any problems, but after soft reset, I am pressing POWER and OK button and going to bootloader mode again, and when I am trying to flash the extracted radio ROM (i tried all of them = 4) and there is a problem. nothing is working. I am waiting and waiting, and there is only info: Checking your device information or something like that. What can I do ? Sorry for my English guys.
Instead of flashing an extracted radio image try to flash a normal shipped rom (if possible matching your cid). Capture the process using usb monitor to see where exactly it fails and which error you get.
Where can I download
pof said:
normal shipped rom (if possible matching my cid).
Click to expand...
Click to collapse
?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Benone said:
Where can I download ?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Click to expand...
Click to collapse
No rom matching your cid is available then, use the TyTN 1.18 rom.
pof said:
No rom matching your cid is available then, use the TyTN 1.18 rom.
Click to expand...
Click to collapse
I tried that ROM 2 times, once I plugged with holding camera button and second time without. I made monitor of QTEK rom aswell, because its the one which is changing phone screen from red green blue stripes to completly white. But nothing else is doin...
A attaching logs in zip file below. I have 3 files from each session, I dont know which are correct, 2 of them i saved and 1 is exported.
What do you think ?
I used USB-monitor from http://www.hhdsoftware.com/
very weird... usb seems not working but for what you say bootloader seems to be ok. Are you sure this was after patching the radio with universal unlocker? it seems totally a different problem :-$
I guess you'll have to wait until t-mob releases a ROM matching your CID and then flash it using the hermimg.nbh sd-card flashing method.
You can also try to connect to it via serial, I have no experience on that, but a search on these forums might tell you how...
keep us updated
How long I have to wait ?
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Do I really have no chances to repair it by myself ?
Benone said:
How long I have to wait ?
Click to expand...
Click to collapse
Until t-mobile releases a rom with your cid... it can be today or next year, I don't know.
Benone said:
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Click to expand...
Click to collapse
I don't think you lost the warranty. They usually charge about 100 eur for flashing it back in the service centre. They do it by inserting a diagnostics sd card, but we don't have it for the Hermes
Benone said:
Do I really have no chances to repair it by myself ?
Click to expand...
Click to collapse
You can try flashing over serial port, and you can try sd-card flashing, but for sd-card flashing you need a rom matching your CID first.
Eureka!!!
Finally I made my device working again!
And I dont have simlock !
After trying everything.... ufffff.
THX !!!!!!
1) I downloaded ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_Unlock_v1.zip
2) Reset my phone in bootloader mode.
3) Plug USB cable.
4) Run HTC_Hermes_SIM_Unlock_v1.
5) After 20 min. my phone said ELO to meeeee He did not have simlock when was saying that.
YE YE YE
That was simple. If you have any Hermes radio problem, try that first - HTC_Hermes_SIM_Unlock_v1.
Will be more often here, forum seems to be really interesting.
YO!
Yipie
Glad it worked
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
nstefanelli said:
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
Click to expand...
Click to collapse
Check your PM's
bwesty said:
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
Click to expand...
Click to collapse
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
jUST DO WHAT I SAY
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
samy.3660 said:
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
Click to expand...
Click to collapse
I cannot do that because the Carrier ROMs that I have aren't for G4, so they arent working. I have three different carrier ROMs for my phone.. and none of them work.
-Stefanelli-
nstefanelli said:
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
Click to expand...
Click to collapse
Check your email, I downloaded and zip works fine here.
i'm facing this problem right now , i will solve it with the original rom .
the problem started when i used shelltool to upgrade my G4 CID Locked to windows mobile 6 crossbow underground edition .
i will give it another try when i get my device alive again ,
any suggestions for the WM6 underground to make it work using shelltool on my wiza 200 ??
--------------------- Edit -----------------------
Finally i solved the problem and installed Crossbow WM6 underground edition .
all i did is to install the original rom from provider and then used shelltool to install WM6 .
i want to mention that my wiza200 is G4 and its CID Locked .
Huge thanx to mUn , you are da man
Mmm
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
lobiik said:
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
Click to expand...
Click to collapse
whats your device and is it G3 or G4 ?
try to do as i did and it worked for me , install the provider flash , then try shelltool to flash WM6 underground .
WBR
a-h-t1 said:
whats your device and is it G3 or G4 ?
Click to expand...
Click to collapse
Mine is G4, dunno if cid is locked or not. I've flashed it as I said with wizard love rom and working without problems. I've tried that again this morning, to flash from love rom, but the same. At 96% it hangs, error 302 Communication error, then starts recovery process, phone goes to bootloader mode. Then is possible to flash it with love rom again with no problem
g4
i have a g4 wizard using the shell tool i have chaged my rom on my phone sometimes 3 times a week just to test them out
the shell tool works if you cant download from the forum here is the link for it
http://rapidshare.com/files/17787647/ShellTool_bugfixed.zip
G4
yes, but when I run shelltool, and press get rom info, all fields states N/A
info from phone is:
ROM Version: 2.26.10.2 WWE
Radio: 2.25.11
ExtROM: 2.26.10.105
IPL/SPL: 2.17.0001
And anyway, dunno exactly which rom for WM6 I can put in (I've just 5.underground_edition_Crossbow_ROM.exe which stucks at 96% with 302 error)
well, I'm dumb, mislooked one stupid thing. Everything passed without errors, Windows Mobile 6 is up and running
happy to know that , the problem was installing rapi ha ??
WBR
No, not really, rapi and that second cab was in device, it was restarted, but I did a mistake - i didn't copied that desired rom into updater directory - that was why were all fields N/A... did that, flashed on first try, without problem
I had the same problem, orginal rom from the provider, and I can reflash it again.....
THX for the info......
ROM verion and link location
Hi lobiik,
which ROM did you use for your device, as you comments above:
"i didn't copied that desired rom into updater directory "
can you please point me to location where i can get the ROM, also proper steps to install the same.
Thanks,
Ajay
HELP!!!!!!!!
I tried flash my G3 with shelltools the program said it worked well i did hard reset then i turned it on it is stuck on 1st front screen bootloader mode is stuck i dont know what is is my device bricked
---------------------edit--------------------------
im a newbie
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
dahdout said:
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
Click to expand...
Click to collapse
What IPL/SPL it displays now ? ,Does it get into Bootloaders ? if it still does than download and flash 'wizard_love_rom' hope it'll recover back.
RE:
It just boots into a white screen. If i hold the camera and power buttons together it boots into bootloader mode, and says USB in the bottom corner. (when i am conncected via usb) but the problem is that active sync doesnt recognize it in bootloader mode. I have tried flashing it in many different ways and i have had no success.
When i go home i will try wizard_love_rom.
and as for the IPL/SPL, i will also check that when i get home.
Where can i download the wizard_love_rom?
Thanks for the help !
RE:2
Hello,
Mr IPL and SPL are both 2.25.0001
My GSM: 02.25.11
My OS: 2.18.0.0
Good News
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
dahdout said:
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
Click to expand...
Click to collapse
Glade its working again !
You got a G4 device,it cannot be CID unlocked,but however,it can be upgraded to wm6 or 6.1,read the methods 'HardSPL' or 'SoftSPL' posted as stickies in the G4 forum for upgrading to wm6 or 6.1.
re:3
thanks, you really saved me with your help!
dahdout said:
thanks, you really saved me with your help!
Click to expand...
Click to collapse
Thanks !
Glade you got it working
sorry, but i need help... again
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
dahdout said:
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
Click to expand...
Click to collapse
ok,for error (300)you can use the RUU MUNS already posted in the 'HardSPL' thread,download the RUU_MUNS application extract it to a folder and copy and paste all the files of this extracted to the folder of the Rom replacing all the RUU files in that folder or copy the nk.nbf folder in the Rom to the extracted folder of the RUU_MUNS and then run the RUU,it will start to flash and complete and hopefully fully boot up.
For edge or gprs,you'll have to get network settings of your network carrier or check out the thread from where you downloaded the rom,its uaually posted there or check out the 'Network' thread.
Aquestion to Zabardast_1 ?
294 error , invalid vender ID
what does that means & asolution to it during rom update
ERROR [294] : INVALID VENDER ID
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
Hey, my phone is an At&t 8525 and after finally fixing the white screen problem and flashing hard-spl v7 and a couple of roms I bricked the phone when flashing the last touch flo rom. During the flash the ruu wrapper stopped and indicated there was an error. I did the recovery and it supposedly completed succesfully if I can remember right. When it reboot it would not get past boot loader. And thats where I am now, the phone will not get past boot loader.
I've tried every method on these forum I could found
SD card flashing dosent work, I get the 002..... error in red.
Flashing the factory an at&t rom dosent work either, gets the same error
\
As for as I know the MTTY method dosent work, I don't know how to type in commands into bootloader and when I type in 14 0 in MTTY nothing happens
KITL is not enabled
IPL-1.04
SPL-2.03
The phone does not boot into bootloader when I hit the power button, I have to hold the comm button, power button, and soft reset in order to bring up bootloader.
When bootloader is up and the phone is connected to the computer via usb bootloader displays usb on the screen and windows detects the device as an HTC device.
Again i've spent about a week and a half trying to fix this phone and I don't know what to do anymore, i've tried more methods than listed above I can't remember though. If anyone can give me a hint on what to do I would highly appreciate it. Thanks
P.S Can someone please tell me how you type commands in bootloader or MTTY
You DON'T have Hard SPL V7 installed..... Otherwise your SPL would be 2.10.
Connect the Hermes to the pc, make sure active sync has benn disabled - got to settings, untick connect by USB. It should register on the pc. Go to bootloader then run the .nbh file for your stock rom... Make sure its the carrier rom that it was shipped with. It doesn't have to be WM05 but it DOES have to be your ORIGINAL carrier rom. Let it run through, you may gewt lucky.....
If it works, INSTALL HARD SPL V7....... Makes it so much easier to fix then...
Good luck...
Thanks for the reply, much appreciated
I tried downloading and sd card flashing a stock rom from a list of factory roms of all Hermes that I found here on xda. It gave me the same error though. I'm not exactly sure which exact rom to download from that list either. Any more help would be appreciated, thx
Wow I feel retarded, I used the wrong factory rom. After I used the right one it worked perfectly, I now have my 8525 back! Thx so much man, ur the friggin man!
Congrats bro you got it atlast. good luck & take care your baby in future. try to help others with your experience.
Glad you fixed it mate, but if I were you I'd also make sure you have Hard SPL V7 installed. It is the safety net to help when things go wrong... Never gonna be 100% safe but better odds with Hard SPL V7...
SPL - 2.10 oli
Cheers...
Ok... Rejoining the 8525 Clan
Is this Forum still alive???
Been a while guys, figured I would break out the 8525... charge it up and see what kind of things are new in this community. Unfortunately, it looks as if the radio is bricked on it. Seems like it will install ROM's that the radio is not included on. NO GSM is on the boot display, which is strange as I was using this phone until I got the Tilt about 1 1/2-2 yrs ago. I was a hardcore flasher back then... every other day it seemed, so I know it has (or had) everything it needed like the Oli 2.10 SPL... but it seems like I cannot recover this radio issue.
I am messing with the different original OEM and Carrier ROMs hoping I can get passed the 11-12% mark, and I will let you know if something changes. Any idea if un-installing SPL 2.10 Oli, and then trying to walk back through the old SPL steps could help? I am just trying to figure out another way to get around this radio issue... or basically I have a PDA, no phone Damn phone hasn't been touched in like 2 years, you think it would be just as fine as it was when I took the SIM out.
Cheers
Can u plz tell me how do you fix the white screen problem ?????
kashifmehmood said:
Can u plz tell me how do you fix the white screen problem ?????
Click to expand...
Click to collapse
Please try searching before posting.
Your answer lies within
Thread closed
Hi folks! Please help me! I killed tons of nerves because of this phone!
So here is my sad story. 1 Year ago i bought second hand HTC HD2. Seller told me that phone is locked to T-mobile(Not US one!! UK one!! Transaction was held in UK). After I got phone I rushed home to install Android and I was successful at this point. Then I bought a unlock code from ebay, so I Finally could make phone calls. Then I realized that the only way I can insert code is putting back WM 6.5. And here the worst part starts. I read hundreds of manuals but still was unsuccessful. I downloaded many official WM 6.5 ROM installers but they didn't flash my phone. They just got stuck at 0% and error pops up. I was trying it for a week and then I just raged and put phone to the shelf and was waiting til I get will power to start over again.
I hear that every phone needs its own ROM installer for particular region and operator but I couldn't find UK T-mobile ROM so used many others and it didn't help.
I also heard that by IMEI it is possible to find to what operator the phone is locked(just to check if seller didn't lie me) but again I didn't manage to do so.
Here is my IMEI 354120035834066
Please experts help me, little nooby, with this horrible situation.
thank you
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
samsamuel said:
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
Click to expand...
Click to collapse
Thank you, but always when I am trying yo install HSPL4 critical error comes up. I think it comes up because I have spl 2.1000000 which should be 2.08 I found information that in order to downgrade to 2.08 I need to flash official ROM. But when I am trying to do so it is always stuck on 0%...
I am so $%^& up ...
any ideas?.... thx
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Mister B said:
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Click to expand...
Click to collapse
Hi. Thanks for ROM, but still.. got stuck on 0% and doesn't go further..
When I try to install HSPL4 it always gives me critical error...
Fixed my problem. Now everything works fine!! Thank you very much guys!!
how ??
rom4eg said:
Fixed my problem. Now everything works fine!! Thank you very much guys!!
Click to expand...
Click to collapse
explain