Hi,
I dropped my lovely two week old tytn in the loo and after a clean and splitting the case open and leaving it to dry behind the fan of one of our hottest severs I eventually got it back to life except for two problems, bluetooth no longer worked and battery life seemed very short. I couldn't claim on insurance but realised I couldn't do without a tytn (life was just so empty ) I managed to get a discount from the shop on a new one. The screen shows slight watermarking when viewed at an angle and is not quite as bright as the replacement
Feeling I had nothing to loose and that there was a slim chance the bluetooth problem might be fixed with a reflash , I flashed it wth the HTC QTEK_001 1.18.255.3 rom. the flash was successful but didn't cure the problem, so instead of stopping there and just for curiosity I tried flashing it with the i-mate CDL_001 1.20.305.3 rom - well curiosity killed the cat, the white start up screen shows a mosaic pattern strip about 3mm wide at the top and on left side starting at top M05 S04 B05 and bottom left D1.18 it also flashes no GSM before moving to the blue windows startup screen where it hangs.
I tried flashing with the htc rom that worked from the mini sd card but it doesn't seem to see it, I get the tricolour screen with serial displayed in the bottom part (which changes to usb when plugged in).
I followed the suggestion on the wiki and ran usbmonitor, file is attached, the error I get is ERROR (222) : Device not responding.
Is there some way to force the update onto the phone.
I hope someone can help, althopugh it will probably be a back to the shop job for the bluetooth in any case.
Thanks in advance for any help.
The USB dump shows nothing useful
Does it show the "USB>" prompt in mtty?
can you enter bootloader commands?
pof said:
The USB dump shows nothing useful
Does it show the "USB>" prompt in mtty?
can you enter bootloader commands?
Click to expand...
Click to collapse
What are bootloader commands and how do you enter them ?????
PURESKILLZZZ said:
What are bootloader commands and how do you enter them ?????
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
pof said:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
Click to expand...
Click to collapse
Many thanks buddy .,....
I will try this when I next have access to a PC, probably Tuesday next week. thanks for replies so far.
Ok ... I have 1 small question. How do I put the MDA into bootloader mode ?
PURESKILLZZZ said:
Ok ... I have 1 small question. How do I put the MDA into bootloader mode ?
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Bootloader mode: Hold side OK and POWER buttons together and reset with stylus.
harryk1372 said:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Bootloader mode: Hold side OK and POWER buttons together and reset with stylus.
Click to expand...
Click to collapse
That didnt work ... Found out process ... Just hold camera button while turnng on phone.. Many thanks fior your help...
PURESKILLZZZ said:
That didnt work ... Found out process ... Just hold camera button while turnng on phone.. Many thanks fior your help...
Click to expand...
Click to collapse
i see... i realized that your hermes is herm300, if it's mda vario ii, and seems the button configuration is slightly different then.
harryk1372 said:
i see... i realized that your hermes is herm300, if it's mda vario ii, and seems the button configuration is slightly different then.
Click to expand...
Click to collapse
Yeah ... But I got it all squared away ... Now to just cid unloc this damm MDA from the uk.
Related
ok, now I am totaly screwed.... imate stuck in loading screen with version numbers etc... Not going further and bootloader not available.... Is there any way to communicate with unit while it's in this mode?
what you are saying is unclear. Does your device say "Serial" (or "USB") on top with "V 1.06" on the bottom?
If so, you ARE in bootloader mode. If not, then please specify what it actually says on the screen
no, it's not in bootlader mode. it's in Tmobile screen at the bottom it says R 1.12.00
G blah
D blah
it stuck there. and I can't enter bootloader mode. looks like it's totaly dead
What happens when you try to enter bootloader (Power - Action - stylus)?
What happens when you try to press (Camera - Record - Stylus)?
GO TO HELL ROM 1.72.104
F%@#&!?G FREAK ROM!! :evil:
Please calm down... in a day or two, this problem will be solved and everyone will probably be back to where they were
((and a lot smarter than they were too))
Victor said:
What happens when you try to enter bootloader (Power - Action - stylus)?
What happens when you try to press (Camera - Record - Stylus)?
Click to expand...
Click to collapse
It both cases it still sits in this screen
Try removing the battery and waiting for a period of time (20 Mins ??)
Then try the two things again (first without the battery -- for the heck of it -- and then replace the battery and try them)
...obviously, you need to remove it from the charger too :wink:
to be clear... nothing is expected to happen when you try to do these without the battery in, except perhaps (??) clear out any remaining charge held in capacitance, if any.
Kinda like removing the batteries in the remote control of a TV and then pushing a button on it (there is always enough charge in the capacitors for a single push/command to the TV
that once happent to me
and softreset dident help
so i did a hardreset and that fixed it
fixed my data too though :/
Rudegar said:
that once happent to me
and softreset dident help
so i did a hardreset and that fixed it
fixed my data too though :/
Click to expand...
Click to collapse
nothing happenes Sent email to imate tech support. I am not sure if they going to warranty unit with Tmobile betta screen stuck on IMATE. looks like i am short 700 USD........
Is there any way to communicate with XDA2 when it stuck in this loading screen? Terminal via serial cable doesn't work. anyother low level programs are out there? please, help.
Have figured out that the problem is in the Bootloader. If there is a way to (and I know there is) revert to an older Bootloader version, then the problems will all be solved.
Problem Solved : Dead devices due to tmob 1.72 + Downgrade
OK Guys. Problem Solved : Dead devices due to tmob 1.72 + Downgrade
http://forum.xda-developers.com/viewtopic.php?t=8606
That's great, but unfortunately my device is one step more screwed that others - no bootloader not even working Windows now.
Is there any way to boot directly from SD card?
victor,
can you upgrade or downgrade the bootloader ? If you can, HOW? please post the way to upgrade or to downgrade the bootloader. :shock:
ID64,
I had an XDA I and wiped the bootloader by accident. As far as I know, you have only two options. The first one is JTAG [http://www.xda-developers.com/jtag/] but I don't think the boards have been documented yet for XDA II. The other option is to bring it back to where you bought it from. Tell them there's something wrong with it and play dumb. If you're lucky they might replace it for you, if they assume that you are still within warranty.
Yes, there is a way to upgrade/downgrade the Bootloader. I just don't know how.
The bootloader is locked, that is the problem you have (except for those who cannot access the bootloader).
If you know the right syntax and use the password to the bootloader (it is BOOTLOADER), you can load the proper ROM back using the "LNB" command. However, they have changed the syntax since ITSME's doc on the subject, or he mis-documented the syntax to the bootloader. Or at least his syntax was wrong with 1.06 version.
I got mine fixed, but I have means available that 99.9% of the people out there do not have. If I knew more, I would tell you about the percise syntax in the bootloader -- but alas, I am not a developer.
Victor said:
Yes, there is a way to upgrade/downgrade the Bootloader. I just don't know how.
The bootloader is locked, that is the problem you have (except for those who cannot access the bootloader).
If you know the right syntax and use the password to the bootloader (it is BOOTLOADER), you can load the proper ROM back using the "LNB" command. However, they have changed the syntax since ITSME's doc on the subject, or he mis-documented the syntax to the bootloader. Or at least his syntax was wrong with 1.06 version.
I got mine fixed, but I have means available that 99.9% of the people out there do not have. If I knew more, I would tell you about the percise syntax in the bootloader -- but alas, I am not a developer.
Click to expand...
Click to collapse
Thanks for the reply, Victor. When you talking about commands for bootloder what connection to PC you are talking about? Serial or jtag?
I am referring to the device in the cradle, in bootloader mode. The screen in this mode should read "USB" on top and "V.1.06" (or whatever version) on the bottom. Very hard to read, as there is no backlight.
Anyhow, just for fun.... why don't you try the following:
Uncheck the USB option in Active Sync Connection Settings
Cold boot your system (hard reset)
place the device in the cradle
run the communications software (found on this forum)
When asked which COM port to use, click on the down arrow and see if there is a USB port listed (should be top entry in list).
If so... click it. (if not, you are basically done)
After clicked, then hit return (enter) on the pc a few times.
Anything happen?
Hi,
I did the popular mistake, tried to unlock with Universal Unlocker , thinking that this is the staff to unlock all the HTC phones.
Ok. What I have now:
NO GSM - we know that
Tried to install radio roms from here, nothing. I got the information about "Checking the information...." and it is hanging like this.
I made reser and HARD RESET aswell.
I tried to install a lot. Nothing helped.
I had radio ver. 1.05.... I remember that. I have my phone from T-Mobile from UK. I had everything nice, now I have four stripes - RED GREEN BLUE and WHITE and ther is written:
HERM300
IPL-1.01
HERM300
SPL-1.04
Can anybody help me ? I tried to download mtty.exe and put all the commands (not PASTE and it still not working.
Now is 6am in Lisbon. I was sitting all that night and I am finishing writting this post.
Help if you can, regards.
Ben
Have a look on this topic http://forum.xda-developers.com/showthread.php?t=280733
It did not help. Where I can get this Qtek rom ? Is that OK for my device ? I have VARIO II from T-Mobile.
I woul like to try instal this - DUMPED English ROM from TMobile Vario II from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_DumpedRoms
but i dont now how. There are 3 .raw files, how to put them to my phone ?
That solution didnt help: http://forum.xda-developers.com/showthread.php?t=280733
What else I can do ? I was trying with QTEK rom and a got white screen on the phone and 0% on the computer. It was hanging. I tried 5 times. Then I tried to install the Radio Rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
I choosed all of them. Nothing. All of them are hanging on:
Chencking the information on your device... Please wait..
Then there is a screen to update. After long time. So when I press the button is still the same info. Checking the information on your device... Please wait..
And its hanging. When I reset to bootloader again the soft telling me:
This ROM Upgrade Utility does not design for your device.
Please get probper ROM Upgrade Utility and try again!
Where can I get the radio version 1.05 for T-Mobile Vario II ???????????
Is there possibility to download from somewhere ?
Or maybe I should try other solution ?
Read "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Yes, I was tying point 5 few times. The problem is, I can connect through mtty.exe without any problems, but after soft reset, I am pressing POWER and OK button and going to bootloader mode again, and when I am trying to flash the extracted radio ROM (i tried all of them = 4) and there is a problem. nothing is working. I am waiting and waiting, and there is only info: Checking your device information or something like that. What can I do ? Sorry for my English guys.
Instead of flashing an extracted radio image try to flash a normal shipped rom (if possible matching your cid). Capture the process using usb monitor to see where exactly it fails and which error you get.
Where can I download
pof said:
normal shipped rom (if possible matching my cid).
Click to expand...
Click to collapse
?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Benone said:
Where can I download ?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Click to expand...
Click to collapse
No rom matching your cid is available then, use the TyTN 1.18 rom.
pof said:
No rom matching your cid is available then, use the TyTN 1.18 rom.
Click to expand...
Click to collapse
I tried that ROM 2 times, once I plugged with holding camera button and second time without. I made monitor of QTEK rom aswell, because its the one which is changing phone screen from red green blue stripes to completly white. But nothing else is doin...
A attaching logs in zip file below. I have 3 files from each session, I dont know which are correct, 2 of them i saved and 1 is exported.
What do you think ?
I used USB-monitor from http://www.hhdsoftware.com/
very weird... usb seems not working but for what you say bootloader seems to be ok. Are you sure this was after patching the radio with universal unlocker? it seems totally a different problem :-$
I guess you'll have to wait until t-mob releases a ROM matching your CID and then flash it using the hermimg.nbh sd-card flashing method.
You can also try to connect to it via serial, I have no experience on that, but a search on these forums might tell you how...
keep us updated
How long I have to wait ?
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Do I really have no chances to repair it by myself ?
Benone said:
How long I have to wait ?
Click to expand...
Click to collapse
Until t-mobile releases a rom with your cid... it can be today or next year, I don't know.
Benone said:
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Click to expand...
Click to collapse
I don't think you lost the warranty. They usually charge about 100 eur for flashing it back in the service centre. They do it by inserting a diagnostics sd card, but we don't have it for the Hermes
Benone said:
Do I really have no chances to repair it by myself ?
Click to expand...
Click to collapse
You can try flashing over serial port, and you can try sd-card flashing, but for sd-card flashing you need a rom matching your CID first.
Eureka!!!
Finally I made my device working again!
And I dont have simlock !
After trying everything.... ufffff.
THX !!!!!!
1) I downloaded ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_Unlock_v1.zip
2) Reset my phone in bootloader mode.
3) Plug USB cable.
4) Run HTC_Hermes_SIM_Unlock_v1.
5) After 20 min. my phone said ELO to meeeee He did not have simlock when was saying that.
YE YE YE
That was simple. If you have any Hermes radio problem, try that first - HTC_Hermes_SIM_Unlock_v1.
Will be more often here, forum seems to be really interesting.
YO!
Yipie
Glad it worked
...tried to unlockit with the athena-unlocker! After Step 1 it startet to Step2 und suddenly the connection was lost!
Now the battery lamp of the Ameo is in green mode!
I can make a factory reset, but I see no bootloader mode!
Screen is black an a green light aroundthe joystick! The Connection via active sync to my pc isn't available any mory!
What do you think?
game over - any change to bring my Ameo back to life?
Edit1: ther is no MiniSd Card inside
Hi, I do not think your Ameo is lost. Some else hat the same problem, please check http://forum.xda-developers.com/showpost.php?p=1358430&postcount=35 and try the steps described there. In most cases, it is also possible to flash WM6 if your device is stuck in the bootloader.
There are two things I would like you to try:
- To make a Hardreset hold the volume slider down and press the reset button.
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
...you were right - thx a lot 4 the solution
stupiddog said:
There are two things I would like you to try:....
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
Click to expand...
Click to collapse
At last -
That (your 2nd tipp) was the solution -WM& upgrade is now running on the ameo (now at 5%)!
Thx a lot
Jackpot thx -
Kisses from Austria
Many thx!
utakurt said:
At last -
That (your 2nd tipp) was the solution -WM& upgrade is now running on the ameo (now at 5%)!
Click to expand...
Click to collapse
You're welcome, have fun with WM6 However, if you want to kill the SIM-Lock/Net-Lock on your device, you have to run the unlocker again. It seems that WM5 has some problems running the unlocker while WM6 does not.
After you successfully run the unlocker again, remember to flash your WM6 ROM again (watch the battery power, it should always be >50% before starting flashing!) so you have the newest Radio version.
If problems persist after flashing, this page in the XDA wiki might be helpful: http://wiki.xda-developers.com/inde...e Athena Unlocker - the Black Screen of Death
stupiddog said:
There are two things I would like you to try:
- To make a Hardreset hold the volume slider down and press the reset button.
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
Click to expand...
Click to collapse
Hi, mate
Wot if those two things does not work??
i mean
if we can not get into boot loader or hard reset
i have this ameo does not go into boot loader or does not do hardreset
only red light on the joystick
problem occured while unlocking with Olipro, completing step 1 (got stuck at the point of saving the spl file)
thank you very much in advance for your help
BR,
Hi does anyone know if there are WM6 ROMs for the SPV C550 if not are there any good WM5 ones?
look topic about wm5 for hurricane, there are also links to wm6 for hurricane device
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Has anybody tried this ROM?
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Ideal thanks
So is the 566.zip the WM5 or WM6 rom and has it been tested?
Whats the new SPL?
hI ALL, can u tell me the mini guide how to install this rom? I did it once to my sda but I dont remember now, where is the nbfupdatetool and RUU and patched RUU..???
when I type l c:\wm6.bin it give me this:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000 MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
cmd>
maybe damaged rom, or any idea?
Gang: Make sure you're CID unlocked. (Eg, when you issue "info 2", it says HTCSuperCID).
How can do that cid unlock? give me some working link to download that tool or something. thx
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
hmm, thx for guide, I believe it will work, but I have little problem : now I cant even connect to activesync so I cant do cid unlock, any idea how to fix that
lazaj007 said:
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
Click to expand...
Click to collapse
Thanks for helping out!
A few questions?
1. This link "http//www.spv-developers.com/content/SPV-Services.zip" takes me to Wikipedia.
2. Where can I find the patched ruu to update the spl. It wasn't in the zip file?
Thanks in advance!
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
gangstaunitg said:
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
Click to expand...
Click to collapse
DoH! I didn't notice the missing ":"
Cheers!
Anybody have idea why I cant connect to activesync after spl upgrade ? Before spl upgrade it all goes well. Can I do something with it?
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
I did it !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THank u all, thankS
This rom is amazing, everything work perfect, and it looks beautiful,
one more time thank you. jUUHHHUUUUUUUUU
lazaj007 said:
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
Click to expand...
Click to collapse
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
MrMiyagi said:
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
Click to expand...
Click to collapse
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
MrMiyagi said:
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
Click to expand...
Click to collapse
Heh heh ... seems I'm posting to myself ... that's cool I like my own company ... So I reflashed the SPL and some of the problems have gone away.
Phone will boot OK now ... but it will still "go to blank screen" and require plugging into the USB cable to "wake it up"
I'm out of ideas now ...
[FULLY SOLVED]HELP！！！I cannot log on to OS after flash Titan HARDSPL 2.40
I followed Titan FAQ and used HARDSPL MFG to unlock my Titan. It seems that the phone has been unlocked because there is the data on Tri-color Screen after the complete flashing.
TITA100 MFG
SPL 2.40. Olipro
CPLD-9
However, the Titan won't restart itself and I cannot reset it by myself either! It just freezes on the Tri-color screen and shows the above data. (even after a soft reset/hard reset, it goes to the Tri-color screen)
I am toally frustrated on it. Anyone please please please help me on this issue? This is totally different from the kaiser flashing.
I greatly appreciate any help!!!
Does it say Serial at the bottom of the screen??? If so, plug it into the PC, now does it change from serial to USB???
azclown said:
Does it say Serial at the bottom of the screen??? If so, plug it into the PC, now does it change from serial to USB???
Click to expand...
Click to collapse
yes yes yes that is what it is doing!
unplug the cable, it changes to serial. plug the cable again, it changes back to USB.
Who is your carrier?
At this point you can Flash the radio via the SD card method, OR use the official Sprint Release to get the 3.39 radio on your phone.
azclown said:
Who is your carrier?
At this point you can Flash the radio via the SD card method, OR use the official Sprint Release to get the 3.39 radio on your phone.
Click to expand...
Click to collapse
Carrier is Telus. I am in halifax, Canada.
what does that mean by the freezed tri-color screen? is that mean the phone is failed unlocking?
dewydewy said:
Carrier is Telus. I am in halifax, Canada.
what does that mean by the freezed tri-color screen? is that mean the phone is failed unlocking?
Click to expand...
Click to collapse
no not necessarily, while its true your stuck on the tri-color screen, this is only a minor problem caused by unlocking, there's a topic somewhere that explains why it does this, and a fix. But before you try "fixing" it, you can now flash your phone to some custom ROMs, like DCD. Update its Radio and ROM, And try soft resetting it again. If its still stuck... ill see if i can find the page..
right so I'm back and found what you were looking for, what your experiencing is being stuck at the Bootloader, Ive had this problem before when unlocking my phone as well.
Here's the Wiki.
http://wiki.xda-developers.com/index.php?pagename=TitanProblems
dewydewy said:
Carrier is Telus. I am in halifax, Canada.
what does that mean by the freezed tri-color screen? is that mean the phone is failed unlocking?
Click to expand...
Click to collapse
No, the phone is unlocked, however it will not function because you have the wrong radio and rom on it.
Like I said, you have 2 options.
1) Download the latest Official Sprint Release or
2) Upgrade your radio using the SD method.... <-- preferred
Can you take your microSD card and format it FAT32, 1k cluster....?
Still don't understand...
Without being able to load into the Pocket PC's OS. How could you flash a new radio and a new OS?
P: My device is stuck at the Red, Blue and Green Screen?
S: To exit the bootloader, press the reset. You may need to reflash the Radio/Operating system ROM
Is the one you just mentioned? I have not flash any rom or any radio yet. The titan just freezes there before I take the next step.
dewydewy said:
P: My device is stuck at the Red, Blue and Green Screen?
S: To exit the bootloader, press the reset. You may need to reflash the Radio/Operating system ROM
Is the one you just mentioned? I have not flash any rom or any radio yet. The titan just freezes there before I take the next step.
Click to expand...
Click to collapse
PM me your aim or yahoo or msn screenname and i'll walk you through it
coffey_joshua said:
PM me your aim or yahoo or msn screenname and i'll walk you through it
Click to expand...
Click to collapse
replied!
Thank you heaps!!!!!
Also, this thread can help you alot....
Start at STEP 5....
http://forum.ppcgeeks.com/showthread.php?t=17667
Thank you, Thank you all. Especially coffey_joshua, he is definitely the savior, lol.
I just dont know how much I should appreciate here. Thank you heaps everyone! You guys are the best, kindest and most talented people I have never meet in any forum!
dewydewy said:
Thank you, Thank you all. Especially coffey_joshua, he is definitely the savior, lol.
I just don't know how much I should appreciate here. Thank you heaps everyone! You guys are the best, kindest and most talented people I have never meet in any forum!
Click to expand...
Click to collapse
this is in partly due to the fact were practically in love with our phones now, and don't mind sharing that kind of appreciation we have grown accustomed to.
That or were just addicted