HELP! think I've stuffed my TMOBILE uk hermes :-( - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Hi guys,
Upgraded to 1.16 radio - (Tmobile UK ROM)
This kept 'hanging' so upgraded to 1.20 - this failed
Left with NO GSM - followed steps as requested set pass etc.
Still wouldn't upgrade
Tried to put latest ROM on (South african?) this FAILED but installed boot load 1.09 - argh!
BOUGHT (£20) the imei-check to downgrade - this WONT WORK - keep failing!!
Please help - stuck now - phone boots - but has NO GSM all the time...
Please help!!

please attach a usb monitor capture of a full rom upgrade until it fails. Probably will be "cid not allow (255)", but just to make sure.
No T-MOB001 rom exists yet

Did that - thats exactly where it failed!
Is it stuffed? :-(

I don't know, never had one of those with "NO GSM" error on my hands.
Probably as radio is screwed CID is corrupted and you'll not be able to flash a ROM even with your original CID. I think for you the best would be to send it to service centre.

Yeh, thought it may be stuffed! FUnny thing is, when I do a hard reset, it doesn't have the NO GSM, it reports 1.16.0.0, it's as if the T-Mobile customs reset it all. Is there any way of stopping the customs?
Regardless, I have had the phone < a month so I'm ringing customer services to see what they can do - maybe not admit I've tried to upgrade it just yet!!!

roger said:
Is there any way of stopping the customs?
Click to expand...
Click to collapse
I guess by "customs" you mean the Extended Rom, if yes, just do a soft reset before it installs (3 seconds). But I don't think it would do any difference...

Ok- update to problem,
Managed to downgrade from 1.09 to 1.04 of bootloader usining IMEI-CHECK.
Did HARD RESET and plugged in hermes when "press screen to continue" came up (just booted) linked to ACTIVESYNC then ran the software IMEI-CHECK sent me, this connected to hermes and asked for .unl file from imei-check. This 'downgraded' to 1.04 of bootloader.
Then managed to install a 1.13 radio rom - hermes still kept hanging -but I could use phone a little (managed to make 2 calls before a lock up). I was going to re-install another full rom upgrade - I think this may have sorted it, but by this time I had rung T-Mobile support in UK and they agreed to replace unit (I pretended it had gone wrong 'all on its own' hope Karma doesn't catch up with me!)
I THINK I would have managed to sort this using the solution from IMEI-CHECK and this forum by reapplying another full ROM upgrade. So thanks to everyone for their help! Hope this is of some use to someone!

Related

HTC HERMES (M3100) - fatal crash, PLEASE HELP!

Hi,
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
Please help.
Thanks
If your device is still working ok as a PDA then hopefully it just screwed up the radio update of your device.
Try reflashing the Radio only
Look Here
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Post back with results
Regards
S.K
EDIT: Sorry only works on 1.04 bootloader only. Afraid your gonna have to wait for Pof to come up with a 1.06-1.04 workaround
Hi S.K,
Thanks for the info. I have now tried installing the HERM_1.20.31.10_type2_radio_fixed upgrade but unfortunately the radio upgarde crashes also. It all seams to go well, (after using MaUpgradeUt_noID.exe twice) the phone says "Upgrade Radio Stack Please wait" and the progress bar appears on the PC but then after 10 mins I get an ERROR 114: RADIO ROM UPDATE ERROR.
Do you think this might be becuase the last upgarde partly installed bootloader 1.06?
Any other suggestions - I'm desperate to get the hpone on M3100 working again.
Thanks
Read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Please post USB monitor capture, otherwise can't help u.
Hi Pof,
Thanks for the offer, I will sort out the usb software on Monday. Are there specific actions that I should try, obvioosly I will usb monior everthing I do but I want to keep it to the point and not waist yr time trailing through huge log files.
Cheers
BTW - I have tried all options of recovery, such as attempting to install the latest radio and trying to install the new rom from an sd card, trying several roms and using imei unlocker - all without any joy.
I think the problem is that I have partially installed radio and bootloader 1.06 so I can't fix the problem.
Thanks again.
@wotthefok:
For me is faster to look at the usb log file, then I exactly know why the upgrade fails, otherwise I have to decode it from your feedback and I can't be really sure. Check the "upgrading problems" page on the wiki, if none of the steps there seems to fix your problem, post USB monitor log please.
Log Files as requested
Hi,
I have captured information using usb monitor and attached the zipped log files for your attention.
The first is called USB_monitor_log_Herm_120Radio_twice. This log details attempting to install the HERM_1.20.31.10_type2_radio_fixed upgrade, and running it twice - just in case.
The USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_twice.zip details attempting to install the RUU_HER_Cingular_1.34.502.1_1.16.00.00_wwe_cws_ship upgrade, simply using the standard ROMUpgradeUt.exe method. This generates the expected Vendor ID error.
My primary focus is to install the radio upgare or download my bootloader to 1.04. The PDA part of my m3100 does now freeze occasionally but at least functions whereas the phone is completely dead.
Thanks in advance.
Please attach capture in *ANSI TEXT FORMAT*, the .lgs file you zipped is totally unuseful
Edit -> Export and Save as type "ANSI Text files".
Also make sure you export in "COMPLETE" view, see the wiki for more details.
OK, Spot the novice.... I have now created a txt log file that captures activity of me running the 120 Radio upgarde - but only once this time. I still had to zip the file due to it's size. Hope this is OK.
I'll send the other logs within the next couple of hours. Please let me know if the output I have sent so far is acceptable?
Thanks
wotthefok said:
Please let me know if the output I have sent so far is acceptable?
Click to expand...
Click to collapse
No, it's a "basic" capture, you have to export a "complete" capture:
Start USBMonitor.
File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
In the upper part there are two tabs: basic and complete. Click on "Complete".
Right, Try again (duh!) OK, I've tried to keep the log files names as self-explanitory as possible... USB_monitor_log_Herm_120Radio_run1.zip is the r20 radio upgrade, 1st run and USB_monitor_log_Herm_120Radio_run2.zip the second run - without disconneting or resetting the device.
USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_ran_twice.zip is the Cingular upgrade run via the ROMUpgradeUt.exe, again run twice without disconneting the device.
Hope I got it right this time.....Please let me know if there is anything else I can do.
Thanks.
This time you got the captures right
- You're on bootloader 1.06: You don't have 'rtask' command, you won't be able to do any radio upgrade only.
- Your device is not CID unlocked (Security level=FF, unprivileged)
- The bad flash caused the CID area to corrupt (CID: Wait interpreter timeout)
- When flashing a full ROM you get a CID not allow (255) this is because your corrupted CID doesn't match the CID on the ROM.
The radio part is screwed, you could have fixed this if you where in bootloader 1.04 by flashing a full ROM, but as you are in 1.06 you can't because of CID checking. But you're lucky because the OS ROM is intact and you can boot the OS, you should be able to downgrade to bootloader 1.04 from OS and flash a full ROM after, which will hopefully fix your radio.
Just wait until a solution to downgrade bootloader is available (I'm working on it).
Hi,
As I suspected.... Suppose it's not all bad news though - just means that I have to be patient and use my communicator once more. Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
I have already got a IMEI-CHECK sim unlock from where I originally got the M3100 unlocked from Orange to work on o2. That said, I have run either unlocker 2 or 3 with the .unl that I know worked I now get
HTC HERMES v3c unlock
Starting communication.........
Checking device..............ERROR
The device you try to unlock is not supported.
Please contact your supplier site.
Device is rebooting
Press any key to quit this application.
I'm currently chatting to the guys at IMEI-CHECK re this problem.
Anything else I can do to assist you in anyway??
Cheers
wotthefok said:
Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
Click to expand...
Click to collapse
They have it (M3100v3cUnlock.exe), but it will not work on your device because your IMEI is corrupted and their unlocker will not be able to read it and to check/compare with the .unl key file.
Hi,
Just a quick update. The guys at MIGsofT LTD have VERY VERY generously said they'll have a look at the problem for me so my phone will be winging it's way to them today.
Thanks for your assistance and helping me be certain of the problem and to better understand the root cause.
Hope this information will prove useful to others.
Another quick update...
The guys at IMEI-CHECK (MIGsofT LTD) have rectified problems with my handset and managing to reinstall bootloader 1.04 in the process!!
They also turned my phone around in under three days and only charged me the cost of postage! I had previously been a customer of theirs but it was still a very generous and helpful offer and I would certainly pay for the service than have a duff handset - after all £250 + for a paperweight is rather excessive....
If you're experiencing a problem like mine why not get in touch with them and offer them money to have a look at your handset? No Guarantees but it seemed like my last chance, for a while anyway.
Praise to IMEI-CHECK for a brilliant service - they are King of the day !!

Please help.. a little girl waits :(

Heh apologoies for title but im really stuck and desperate for any help!!
I have been trying to unlock my Cingular 8525 for many hours now without any luck.
I bought it off ebay knowing it was locked because I had seen these forums and knew it wasnt too harder job. I live in NZ we have a compatible 3G network here (they sell these phones branded as JasJams).
Anyway I dont have a cingular sim card, only a Vodafone NZ simcard. I dont know if that is a problem for me or not...
My problem is that I get part way through the update process and the connection between pc and phone gets cut everytime at the same place.
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
It then gives me the button to select the Update button (Update the radio and bootloader)
So I click that, it gives the next screen, click next, tells you its going to take 10 minutes etc, so click next,
It then instantly disconnects the active sync connection and about a minute later I get an error screen saying the unlocker encountered communications errors.
I have been through this whole proccess 6 times now with no joy
Someone pleeeeeeeeease help me
Thanks
im willing to pay for a code all i want is a unlocked sim phone none of this radio stuff etc
try Wiki
http://wiki.xda-developers.com/
or alternatively
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
Thanks but not really helpful, I have read the wiki through and through. I have tried that flashing HardSPL v7 and i get exactly the same problem.
PLEASE somebody help me
The only piece that is confusing is what to do once your done. The instructions say that you will be replacing your radio with a tweaked one to allow the unlock. After the entire process is done I assume you will need to have your favorite radio (1.40.3 in my case) handy to flash back onto your Hermes?
I also assume that flashing your favorite radio back to the Hermes won't lock it back again.
To be honest, I'd suggest going back to basics. You could try quite a few workarounds and end up doing this anyway..:
Reflash the original ROM your phone came with. Should be found easily via wiki.
Then you can start upgrading again.
If that's difficult, try flashing from your MicroSD card, which I've found never fails, having bricked my Hermes quite a few times now with my own cockamayme (sp) versions of ROMs that I've cobbled together from bits of code and chewing-gum.
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
amet said:
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
Click to expand...
Click to collapse
She want's to SIM-Unlock, not to CID-Unlock.
Do you use Vista? I encountered a similar problem with Windows Vista. Try a PC with Windows XP for the unlocking process.
ok my bad....
I've seen this issue with v1.4 Olipro. Upgrade bootloader to the latest Olipro 2.1 version then re-attempt.
ok thanks everyone for your advice but i am still screwed.
im not running vista.
i can not upgrade to olipro 2.1 because the upgrade utility always gets error 260 (update error) the update utility cannot connect to your PDA Phone.
I have now tried on 3 computers, my own, my parents and my work all resulting in the same thing.
I think now I will try and flash a WM6 rom onto my phone just using the olipro 1.4 and the custom RUU updater and see how I go but I dont have much hope
ok im currently updating the rom to wm6 as posted on the forums and oh my gosh i have a progress bar for the first time ever!! woot~~
um ok. now i have WM6 dopod version and fkn still sim locked someone help me before i throw my phone at the wall lol im going on holiday tomorrow and will have no phone for a week if i dont fix this in the next 3 hrs
Sim Unlock
http://forum.xda-developers.com/showthread.php?t=293665
laurasaur said:
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
Click to expand...
Click to collapse
Do *NOT* soft reset your phone here, it is normal that activesync disconnects while the pda is in bootloader mode (activesync only works while OS is running). Just click "next, next, next" in the RUU and it will go fine.
woooa i think i love you Pof, I seriously do. Im not sure how I became such a noob at reading instructions but im sorry and thank you so much I now have progress bar
if you're short on time avoid any radio updates, they seem a bit hit and miss - its not worth upgrading then going away to find you've got a tossy signal!!!!
hope it worked out!

"no GSM" problem. All workaround posted doesn't work! Pls HELP!!!

Hi all,
First of all I want to let you know that I did search the forum for a solution. In fact, I found a lot of workarounds but none of them actually worked.
Let me give some details about my problem: My Hermes was working fine. I was running the official WM6 ROM supplied by HTC, so no customized ROM here.
It was going fine until the WM frozed. Then I soft reset the device and after that I never got cellular signal again.
While booting the device I got the message: "no GSM".
First thing I tried was to flash a new radio ROM. In all the attempts the progress bar never moved from 0% and after a while I got the communication problem error.
Then I tried flashing a whole ROM. This time the progress bar stopped at 81%. Apparently in the first 81% it flashes the OS and in the last 19% it writes the radio. Anyway, I tried this a few times and never finished.
In fact, after every communication error message I got stuck in the bootloader screen.
The only thing that works is to flash a ROM WITHOUT the radio!!
Is there anything I can do to save my phone or am I condemned to use my Hermes as a phone-less pda?
I tried everything I found in the wiki/forums, but I couldn't find a working solution.
I suspect that the blocks of memory where the radio data reside got corrupted, could that be possible?
PLEASE HELP!
thanks in advance!
Chris
A similar thing happen to me several months ago. While on a call my phone froze and when I soft-reset it the dreaded 'No GSM' issue appeared. I tried flashing radios/full roms/etc, but nothing worked. I ended up sending my phone to the htc repair facility and they fixed it at no cost. (Other than not having a phone for ~10 days)
Thanks dang, but I don't have a HTC service center where I live (Argentina, LATAM)
I'm faithful that the people of this wonderful community will be able to help me.
Just for curiosity, where did you send your device? Is it in the US?
cheers
sounds like a hardware problem to me...
Hi, there! I found that a lot of us who have bricked our Hermes, don't have a responsive radio bootloader, so when they try to flash a full rom, the progress bar hangs to 13%, or 81%. This is because at that time the flasher is trying to enter the radio bootloader, but because it's corrupted, it hangs. Till today there is no known solution to this one. I'm far away from England where I bought my Hermes, so I'm not thinking to send it back for repair. I'm a programmer, so my knowledge may be usefull here. The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
How can I try that?
windshearx said:
The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
Click to expand...
Click to collapse
You can use 'lnb' in HardSPL without having a real SuperCID; however you will not be able to flash a radio with 'lnb' command. The radio chipset has its own bootloader, the and the SPL just acts as a pass-through sending the data directly to radio chipset through the s2410 UART.
I had one device with non-responsive htc_boot and tried all kinds of SPL patches to flash htc_boot again on radio, without success. The only known method to fix this is to take the BGA chip out with hot air and reflash it with special hardware, as it is not common to have this equipment at home, your only option is to send it somewhere to do it for you.
However, I don't want to discourage you to research on it, maybe you find something i didn't
I have a similar problem
I also have a NO GSM and corrupted CID but I can access KITL and use it with PB 5.0. and I followed this steps here but the phone doesnt boot completely. It stops just after the two boot screens on Black WM6 ending on a white screen and the debug window on PB after loading all sort of things begin showing these lines over and over:
@@@@@@ HUB state changes now @@@@@@
[HDC]HubStatusChangeThreadPN TRUE
[HDC]HubStatusChangeThreadPN FALSE
Is there any hope for me? I have the cingular 8525
thanks
Gents, do you think the solution presented in http://forum.xda-developers.com/showthread.php?t=280425 could help me?
Please advise.
thanks again
chriscec said:
Just for curiosity, where did you send your device? Is it in the US?
Click to expand...
Click to collapse
I sent it to the HTC service center in Texas, US.
I just got my replacement from ATT.. Had the same problem. Its a hardware problem.. I wouldnt waste anymore of your time.
first, i'm sorry for my english
I've the same problem with a V1605 (french SFR), i've tried every solution but flash radio doesn't work.
I can flash cooked os without any problem, but it's impossible to put official
It's only a pda now, it's better than a brick
My hernes use to be the same as you 'NoGSM'.I tried to install the official rom,but it 's not work at all.I called to service center ask this problem,so they said that it must be only changed the mainboard. That 's terrible!!!
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
otoro_315 said:
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
Click to expand...
Click to collapse
That only works with phones with KITL...which I don't seem to have.
Sorry, how to config the phone with KITL and solve the no gsm problem.
No GSM but when sim inserted
Hi all, First sorry for my bad english.
I also have 2 bricked Tytn Hermes 200. Its not my personal ones Its my company's property, which pple were using this phones. So i'm facin with problem which many pple here having but with exception. both phones having no gsm error when sim inserted but without sim its fine. In other words , device info showing every info including IMEI when sim unavailable. And some times works with sim but after making few call and receiving phone hangs(not system) and goes off from network but anthena signal still showing few bars. I'm thinking maybe the radio hangs totally and goes off, and after soft restart NO GSM. I also tried many flashing upgrading those things nothing can really help me.
When im flashing original rom from HTC (the latest one HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108) its hanging on 12% and doing 3 or 4 times recovery , but its finishes succesfully. So what exactly happening in 12th%?. Maybe its started flashing radio and stopped on bad block ? But then why its finishes succesfully after few retry?. Ok so if any one wants to experiments on the phones except radio welcome. I'll help. And some can give me quick example of how to check bad blocks?.
Tnx.
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
otoro_315 said:
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
Click to expand...
Click to collapse
My device is still SuperCID and I know I don't have KITL...I have SPL 1.04 as well and HTC Bootloader is 0108. I can't install any ROMs with radios as they will hang at 11/12%. I will attempt this "overload" method where it seems some people have had luck with it...after a few recoveries it just finally installs...but I don't think that will be the case.
If I can't fix this in a few days, I will most likely use my warranty or just wait for the Kaiser.
My variation of No GSM
I feel like I have problem 1A...where I am able to boot into OS but no GSM.
I am still SuperCID, SPL 1.04, HTC Bootloader 0108. Last known radio before corruption was 1.48.00.00. ROM where this problem occured: VP3G 3.60.1.
I was not even in the middle of an upgrade...just a soft reset after my phone ALREADY lost GSM capabilities during a tether session. It was stuck with no signal in Phone Mode...I put it in Flight Mode...then tried to move it back to Phone Mode and it wouldn't do so. I soft reset...and the no GSM stuck.
I tried to reinstall radio...many errors...stuck on bootloader. At first, OS's only were not installing as well but I got past that. Now I am able to boot into OS's with limited capabilities...and they will NOT ACTIVESYNC at all. Regardless of how old or new the ROM is. I tried older OS's that I knew worked in the past for me...but they refused to activesync.
Due to that, I am not able to install latest HardSPL 2.10Oli via SSPL. That seems to be the only way to do it according to my knowledge and what I've read. Maybe mtty was capable but I'm not sure. HardSPL 1.40Oli wasn't giving me any problems though, but I just wanted to have the latest one so I can avoid IPL damage.
I can only install anything if I start the device in bootloader...and I'm only limited to the OS since my Radio Bootloader seems corrupted.
I'm not sure what caused the corruption in the first place...but I feel annoying now posting on different parts of the forum with a problem that seems to be growing in the community.

Recieving [Error 224]

Hello all,
I Eb'd an HTC wizard (cingular 8125) running Wizard Love/NBD WM 6.
On the load screen I get:
AKU 2.3;
IPL and SPL:2.25.0001;
radio:2.25.11;
rom: 6.0.0.0.
My carrier is Tmobile.​
Question 1: If my phone has this newer ROM and it takes calls on the Tmobile network it has been CID unlocked and SIM unlocked...right?
I wanna update my rom and think that I am competent enough to do so but there is alot to learn and this is not my full time gig...right.
Question 2: So, if I am correct in Q1 I should be able to flash roms right?
However when I attempt to do so the RUU gives me [error 224]. Active sync and or WMDC says its connected. (I installed the AS drivers in WMDC)
Question 3: Where do I go from here?
Question 4: The wi-fi is currently not working will a new rom potentially clear this up?
Thanks in advance for the time and advice..
grazie
hmmmm,
Well,did you updated to NBD wm6 yourself ? and how did you updated ? which method you adopted ? SoftSPL or HardSPL ?
You say its SIM unlocked as it takes calls on the Tmobile network .Did you SIM unlocked with lokiwiz03a ?
yes ! a G4 can be SIM unlocked but it can not be CID unlocked,however,it can be upgraded to wm6 rom,but with method either 'SoftSPL' or 'HardSPL'.With your present ipl/spl 2.25.0001 and you say its NBD wm6 running,then it must have been upgraded through 'SoftSPL' method,as it uses patched ipl/spl and Cid unlocks the phone temporarily,but it never permanently CID unlocks the phone.But with 'HardSPL' ,it changes the ipl/spl to a patched ipl 2.21.0001 and spl 2.21 olip.So everytime you want to upgrade,you'll have to upgrade using 'SoftSPL' method.
could you elaborate a little more about this.
Cheers!
Hey thanks for the correspondence zabardast_1, I have been getting frustrated and I have many times contemplated going for the brick or bust approach here.
So, I have done none of the updating on this rig. I rec'd it and I wanted it primarily for wifi however I can't get the wifi card/ (sdiowlan I believe) to even recognize an AP (... I posted in the networking forum but no response.) Thus my own reasoning leads me to believe I should start from scratch with a new rom unless you know of something else.
So, I am not the most savvy and thought that all of the info I had led to SIM and CID unlocked. I just read otherwise last night and in your reply. The info I have provided is accurate the IPL, SPL, radio, although I don't know which NBD release it is; just says 6.0.0.0 and release date: 2/2/07.
I am trying to get the new rom on the my device however and I would've probably already bricked it if I could get an RUU to communicate with my wiz. I always get [Error 224] when I run it and my phone is connected through active sync. I am running vista but have installed the AS drivers for WMDC. I also tried it at work the other day with XP same situ. I then tried flashing from the bootloader screen with an NBD, Wizard Love ( w/ Italian installer?), and T-mob (226102_22610105_022511). The only one that says it will update is the Tmob ROM, however I got cold feet at the update button and canceled.
Other funny stuff I have observed that may or may not be related to the problems I am having are:
Can't install cab files ie (enable rapi or Cert SPCS) and Wiz Sys Tools couldn't read my CID block and hard_SPL G4 gives me REXX error ( SPL_Version has no value).
So, any wizdom you or anybody can drop is much appreciated and needed at this point.
Whew...
Listen carefully. G4 Wizard cannot be CID-unlocked without paying money. (And yes, you are using a G4).
What you need now is to Flash your original stock carrier ROM (Or wizard love) to get your OS back. Then either use SoftSPL or install HardSPL and flash WM6 ROM.
Thanks Starkwong,
I will try installing wizard love tomorrow at work and if that don't work I will attempt a Cing ROM (will all of these work or do I need to mind my G3's and G4's for these???)
Grazie
So, It worked using Wizard Love at work and out of the bootloader window. Now I need to:
1.) Get wifi working.
2.) Get a newer ROM
I put a post up in the networking thread, I am a tool so far as these devices are concerned so be easy on me.
http://forum.xda-developers.com/showthread.php?t=372811
So do I get the wifi issue resolved before I reflash???
Thx again
I don't know what you mean by "wifi not working".
Maybe it is the wifi AP doesn't allow 11Mbps (802.11b) connections?
However, going to any of the WM6 ROMs should already set the registry to allow Wizard connects to G-Only APs. Just use HardSPL/SoftSPL and flash a WM6 and you will see.
OK so "wifi not working" may indeed be a general statement...
What I mean to say is that I am not able to connect to any wireless networks for internet not home (Linksys WRT 54G v5 with ddwrt firmware) or school (university wide) or my city's wifi network. It won't even detect them at least none that Ive seen since I've rec'd this phone. So, that is what I meant by the ambiguous statement.
So, being as your last post was a success I will try as you say and post the results tomorrow. Thanks again starkwong!!!
1 quick thing however, to be sure, I can now try the hard spl or soft spl method of tricking my phone to run an upgrade to WM6?
Still not able to get wifi APs????
OK although I have been successful at reinstalling the Mfg ROM and then Hard SPL'ing my wizard thanks to ya'll I still am unable to connect to a wireless network (see one even). I have the Olip on my SPL and I installed a TNT version of WM6 and I am still at work (drunk but still here). Anyway I can't see my wireless AP and I am beginning to think its a hardware issue if thats possible, i dunno the dynamics of this system maybe thats why it was for sale. In any event as usual I am willing to try what ever you guys throw at me as you're my only hope obi wan. Alright Im gonna go home for the night and try getting on to my home network.
Thanks again for all the help guys.
Is your device a original one from phone operator? I suspect your device is a China Dopod 838 with replaced casing, because the China version has the wifi hardware removed, so wifi can't be started even if an English ROM is used.
Looks to be authentic 8125
Starkwong, the Cingular logo and the 8125 model # are on the phone case where they have been when I've seen them before in pics. Therfore, I dunno I guess it looks like every other 8125 I've seen. Can I check the SN, IME or anything to be sure?
Thanks Again!!!
Starkwong,
I am getting all the options for wifi on my phone the LHS LED flashes green when I enable it and alternates blue green when BT is enabled. So, could it still be that its a dupod? I dunno but I am going home for the night... Thanks for your help. I will try connecting to my home network when I get there.

need some advice - restoring hermes for warranty repair. os done, radio and BL left

Hi,
i must sent my hermes to repairs. so i have to restore it to wm5 and old bootloader.
i have some problems with the gsm module. sometimes i get "no gsm" in the bootscreen and after boot no phone functions. Some time i the radio shows up in boot and i get phone functions. the problem did not appear after a flash. the last flash a month ago.
it seems that the hardware that there is a loose connection. when i make a test call and knock the phone (softly) the phone connection is lost. the "end call" button does nothing and after a while the whole os freezes.
has someone another idea than faulty hardware?
OS is restored to original with the help of mrvranx guide.
whats left is the bootloader and the shipped radio rom.
Bootloader screen shows:
Herm 300
IPL-1.04
SPL-2.10Olipro
Radio Rom is 1.47.30.10
Im a little concerned about mrvranx warning: "If your radio version is currently HIGHER than 1.27.00.00 then it is very likely the radio bootloader is version 0108, this WILL NOT allow the radio to be downgraded to a radio containing BL 0106 and will result in a "NO GSM" error"
but on the next page is a guide to flash the bootloader back step by step to the original. is this method save? and does anybody know which one was the shipped one (t-mobile germany).
last the radio. i can't remember which was the shipped version.
and can i flash whithout problems back to the original? somewhere i read about problems because of the bootloader.
and the last question
in what order must i do this. first radio then the bootloader is right?
many thanks in advance.
washi
just today I had to get my old TYTN ready for warranty/repair.
I followed mrvranx's guide to downgrade my bootloader and it worked flawlessly. I did it all from an XP computer as I was having issue on my Vista machine. Follow it to a T and you should not encounter trouble.
As for the order, I don't think it matters. I did my radio last if you just wanna follow my lead.
As for determining the radio and boot loader version - I'm with Rogers in Canada, they send me my replacement device before I send them the faulty one. I just go into bootloader mode (power on the right side+ok on the left side+reset button at the bottom) and verify the version.
just checked my radio bootloader version. its 108.
so i wont be able to flash a radio < 1.3x?
which is unfortunate because the t-mobile germany never actually offered an official update :/
i just hope the handy will pass with the old os and old bootloader but newer radio.
Is this really needed?
I have to send my phone in as well and didn't know if it was really necessary to do all the downgrading and stuff? i guess can't hurt to be safe though huh
Hey Guys,
I am in the same boat as you all, I am with Rogers and unfortunately MRVANX guide is not online at present, can any one help. Also if you can tell me if it is at all possible, my IPL is 1.04, SPL is 2.10.OLIPRO and Radio version is 1.54.07.00 I am using FARIA.32 ROM
please help.
Thanks
Himanshu

Categories

Resources