Related
Heh apologoies for title but im really stuck and desperate for any help!!
I have been trying to unlock my Cingular 8525 for many hours now without any luck.
I bought it off ebay knowing it was locked because I had seen these forums and knew it wasnt too harder job. I live in NZ we have a compatible 3G network here (they sell these phones branded as JasJams).
Anyway I dont have a cingular sim card, only a Vodafone NZ simcard. I dont know if that is a problem for me or not...
My problem is that I get part way through the update process and the connection between pc and phone gets cut everytime at the same place.
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
It then gives me the button to select the Update button (Update the radio and bootloader)
So I click that, it gives the next screen, click next, tells you its going to take 10 minutes etc, so click next,
It then instantly disconnects the active sync connection and about a minute later I get an error screen saying the unlocker encountered communications errors.
I have been through this whole proccess 6 times now with no joy
Someone pleeeeeeeeease help me
Thanks
im willing to pay for a code all i want is a unlocked sim phone none of this radio stuff etc
try Wiki
http://wiki.xda-developers.com/
or alternatively
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
Thanks but not really helpful, I have read the wiki through and through. I have tried that flashing HardSPL v7 and i get exactly the same problem.
PLEASE somebody help me
The only piece that is confusing is what to do once your done. The instructions say that you will be replacing your radio with a tweaked one to allow the unlock. After the entire process is done I assume you will need to have your favorite radio (1.40.3 in my case) handy to flash back onto your Hermes?
I also assume that flashing your favorite radio back to the Hermes won't lock it back again.
To be honest, I'd suggest going back to basics. You could try quite a few workarounds and end up doing this anyway..:
Reflash the original ROM your phone came with. Should be found easily via wiki.
Then you can start upgrading again.
If that's difficult, try flashing from your MicroSD card, which I've found never fails, having bricked my Hermes quite a few times now with my own cockamayme (sp) versions of ROMs that I've cobbled together from bits of code and chewing-gum.
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
amet said:
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
Click to expand...
Click to collapse
She want's to SIM-Unlock, not to CID-Unlock.
Do you use Vista? I encountered a similar problem with Windows Vista. Try a PC with Windows XP for the unlocking process.
ok my bad....
I've seen this issue with v1.4 Olipro. Upgrade bootloader to the latest Olipro 2.1 version then re-attempt.
ok thanks everyone for your advice but i am still screwed.
im not running vista.
i can not upgrade to olipro 2.1 because the upgrade utility always gets error 260 (update error) the update utility cannot connect to your PDA Phone.
I have now tried on 3 computers, my own, my parents and my work all resulting in the same thing.
I think now I will try and flash a WM6 rom onto my phone just using the olipro 1.4 and the custom RUU updater and see how I go but I dont have much hope
ok im currently updating the rom to wm6 as posted on the forums and oh my gosh i have a progress bar for the first time ever!! woot~~
um ok. now i have WM6 dopod version and fkn still sim locked someone help me before i throw my phone at the wall lol im going on holiday tomorrow and will have no phone for a week if i dont fix this in the next 3 hrs
Sim Unlock
http://forum.xda-developers.com/showthread.php?t=293665
laurasaur said:
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
Click to expand...
Click to collapse
Do *NOT* soft reset your phone here, it is normal that activesync disconnects while the pda is in bootloader mode (activesync only works while OS is running). Just click "next, next, next" in the RUU and it will go fine.
woooa i think i love you Pof, I seriously do. Im not sure how I became such a noob at reading instructions but im sorry and thank you so much I now have progress bar
if you're short on time avoid any radio updates, they seem a bit hit and miss - its not worth upgrading then going away to find you've got a tossy signal!!!!
hope it worked out!
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe
I have a 8125 G4 sim unlocked w lokiwiz and a flashed WMSE5_rev4 with soft spl, well the problem that i have now is that i recentley tried to flash a new wm6 rom without hard spl ( yeah i know stupid) And now i am stuck on tri color boatloader screen no matter if i turn it off or not still goes back to the same thing. and yes the rom that i was flashing was g safe, i think were i messed up is not CID unlocking it with hard spl?when i tried to flash the new rom it went all the way to 100% and then gave error after that. NO activesync connection right now
questions
1- DID I BRICK IT
2- is there a way to recover this device
unlock it again. (CID) i had the same thing on my wiz g4. and no. is not bricked.
ok thank you and i will let u know what happens so i should use hardspl right?
ok thank you and i will let u know what happens so i should use hardspl right?
still lost
Ok this is where im at i have tried to flash other roms, NOTHING. the phone is cycling between charging(when on charger) and bootloader every few seconds then i pull it off and nothing. i cant get hard spl to recognize the phone nor will activesync. i understand that i need to CID unlock the phone but i cant even get that far?
any suggestions? please walk me through it im not stupid but HTC's are a whole new ball game for me. im used to motorolas(by the way they suck!)
thanks in advance
Get the original stock ROM for your Wizard version and flash it to get your OS back, then you can HardSPL or SoftSPL.
p.s. G4 Wizard does not have free solutions to actually "CID unlock". Either HardSPL and SoftSPL are hacks that tricks the RUU to allow flashing, you will still see your device as Locked in WST(Wizard Service Tool).
go to activesycn settings turn OFF allow usb connections and retry
I read it here in another thread after I returned My P4300 to cincinati bell in exactly the same condition you described.
Good Luck
Just did the titan unlocker and now the p4000 is stuck in bootloader with these 2 lines:
TITA100
SPL-1.20.Olipro
i think i need some help
thanks in advance
Marc
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
orangeworx said:
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
Click to expand...
Click to collapse
yes..............
since i'm stuck in bootloader mode, how can i use the ruu update utility ?
i'm getting connectiong failed and only option is to exit utility
any ideas ?
if u are in bootloader connect the usb cable and the phone should say usb at the bottom, just open up the ruu update and it should work just fine
Error 264
update utility cannot connect to your pda
and it says USB on the bootloader screen
SPL is 1.20 olipro
take your SD card out if (with phone powered off) if u have an image on the SD card and retry
no SD card being used at the moment
edit: it seems now it is flashing...
let's say this does work, fact that i'm putting a sprint ROM on my telus phone is gonna be alright?
re-edit: crashed at 11% - invalid command error 290... RUU encountered a communication error
recovery
at 11%, titan reset and went back into bootloader mode, RUU crashed but gave option for recovery which was "successful"
retried the same RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.04_PPST_0619_Ship.exe
and crashed again at 11%
i think i killed my phone
i can't seem to do anything, not the telus wm6.0 ruu nor the one stated earlier...
is there a way i can revert to my previous SPL 1.04 ?
really appreciate the help @ 5:35 AM
got my telus wm6 to run and then decided to up to olipro 2.40
now it won't got past second splash...
radio is 1.32, rom is dcd 3.2.5
now from my understanding of what i've been reading is that i need to revert to olipro 1.20 to be able to flash my radio
and i can't do that since i can't get activesync.
any ideas ?
Get a SD card. Go to WIKI and following reverting to Stock. Then start over on flashing. I have done as you did and fixed the phone.
your phone sounds jacked up, how long is it stalling at 11%, r u giving it decent enough time?
redownload the latest sprint rom from htc america here:
http://216.139.227.226/RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_TITAN_3.42.02_SPCS2.04_PPST_0718_Ship.exe
let it run for at least 20 minutes before deciding it crashed...after 1st boot softreset before letting it run any customizations
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "(294) INVALID VENDOR"
any suggestions ...
thanks in advance for your input
Airborne_Pathogen said:
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "wrong update utility"
any suggestions ...
thanks in advance for your input
Click to expand...
Click to collapse
Are you sure SPL is 2.21 and not 2.21.0001 as IPL 2.21.0001 ?
Well,if its 2.21 only,the phone's got mixed Bootloaders (IPL/SPL),IPL 2.21.0001 are G4 and SPL 2.21 is G3,I don't know how you got it,but your phone is 'Bricked'
mmm it figures
so it appears there could be a problem with the imei program,
as i said it never came out of boot mode after the unlock
and no errors were shown ...
i could get another and replaced the main board, this one is in new condition
except for the custom bricked rom . in the future i will not play with a g4
thanks for the diagnosis, no way to flash a new spl / ipl ... i did read that if
it booted you could get it back in some chance cases .. i am curious as to how this happened (others not doing this for a hobby could brick there only phone)
step 1 - ran imei unlock
never came out of boot mode after
2- flashing the to above roms said to be G4 safe
i never look to see what the ipl / spl were before
i looked with the wizard tool but didn't save it
well you live and learn, it's good for parts now off to ebay for another crack at it ...
thanks everyone ... the best thing about this phone is everything you can do to it
with help from those who know ...
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Custom build wm6 roms like TNT etc... never Brick a G4 phone as no IPL/SPL is included in them,they are completely safe for G4 devices.What I can gather,it must be the wrong imei unlock code perhaps.
Well,like Myrddin Wyllt said,there's no harm in trying,so if it gets into Bootloaders,try to flash the official rom and if there's an error "wrong update utility" ,replace the RUU in the rom with this RUU and run this RUU,hope it might work.
Myrddin Wyllt said:
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Click to expand...
Click to collapse
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
stuck
Airborne_Pathogen said:
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
Click to expand...
Click to collapse
ok, i swapped out every RUU i could find i get errors from
read file
invalid vendor id
wrong update utility
im too new to figure this out ..can you extract a ipl / spl from an
official rom and then flash that to get the boot loader's back in sync
i found the att 8125 ipl /spl nbf when i flash, it runs to 100% reboots but no changes
anyone have a link to flashing just the ipl / spl on the g4
i am most thankful for any advise ..
try running the hardspl on phone, it might just work to revert it back to a G4 spl.
Link to HardSPL : http://forum.xda-developers.com/showthread.php?t=332320
and G4 ipl and spl here : http://forum.xda-developers.com/showthread.php?t=342744
Also I paid to the IMEI Check and I had to change the plate because the PDA died as yours. E had not returned to the money of the IMEI Check only reply to me was that it had to change of plate ..... It had the unblocked CID?
bastards
yes they won't return my money ... somehow they bricked my phone
i would use the hard /spl and not the imei those guys are assholes