I can connect to the device via BT, set up the com ports and everything, but no application will collect data off the device! Has anyone been able to connect a Holux GPSlim 236 BT to their star trek? And if anyone has a working GPS, what model? Thanks
Turns out i'm an idiot and i got it to work just fine!
Related
I`ve serious problem to connect gps receiver (holux gm-210) to mda. adapter is dedicated to mda led in mouse is blinking, etc. but any software can`t see the gps receiver (can`t communicate with him in any com port). where the problem can be ?
mike
I too have same problem, but when I connect my friends Tom Tom GPS is works !! I then disconnect Tom Tom Gps and Connect my Holux GM-21 and that works, but if you soft reset XDA then Holux GPS is not working again.
Please someone help or give links to help.
regards
Lee
Have you turn the IrDA off first ? Check the "data exchange" in the connection page.
IrDA will occupy the COM1..
Hi guys,
I've been using the 1.72 ROM for a couple of weeks now and I must say it is the most stable ROM since I've my MDA II. The radio on/off works like a charm and so does the bluetooth. But.....
I use TomTom Navigator 3 with an Emtac bluetooth GPS. It works fine with this ROM but I can't use TomTom anymore without the Emtac bluetooth GPS. What I mean is: Before this ROM I would sometimes open up TomTom to look something up on the map. This would be with bluetooth turned off and my GPS would be somewere else. Now with this 1.72 ROM and the Bluetooth Tools in it, I can't do this anymore. My MDA II will slow down in opening TomTom and will then freeze. It needs a soft reset to get out of this stage. This is very repeatable. I think it has to do with the bluetooth tools in the ROM.
So my questions are:
1. Does any of you guys have the same problem with a bluetooth GPS?
2. Can I do a hard reset and not let this bluetooth tools be installed and still get my bluetooth GPS working?
I hope any of you knows the answer to this (minor) problem.
Thanks!
Wouter
are you using the latest version of the tomtom gps driver, I had this problem on my old IPAQ 3970. but everything works fine on my XDA with 1.72 and bluetooth tools
I use the very, very latest GPS driver. So you can't reproduce that problem with a bluetooth gps mouse?
Wouter
I have a GlobalSat GPS mouse and it works fine.
Jon
I also have the latest GPS driver with the TomTom Wireless (Bluetooth) GPS mouse and works without any problem
Hi Xzanix,
Just to be sure if I just have bad luck. You can open the map in TomTom and look something up without the bluetooth GPS turned on? (I just want to be sure....)
Thanks,
Wouter
:lol: :lol: :lol:
Hi guys,
This thread can be closed. I solved the problem!
I tell you what I did. I had in the GPS settings choosen for COM5 because I had that one activated in the Bluetooth Tools. This was how TT did work but didn't work with no GPS turned on.
Now I turned Bluetooth Tools off and choose for Bluetooth GPS in the GPS settings. Now it works how it is supposed and I can still look something up on the map without my bluetooth GPS turned on.
I'm so happy! :lol:
Wouter
Cool 8) Was just compiling a reply Nice to read you've solved your issue
Well, thanks for your effort!
:lol:
Wouter
I have updated my XDAii with WM2005 (1.60c), everything I tested works fine, but I only have a problem with MN4.2 and an original Navigon BT Mouse.
I have changed the two .ini-files (prefs.ini + spgps.ini) to COM4 (the outgoing port).
Switching on the BT-Mouse the blue BT-LED of the mouse is flashing but after starting of MN the BT-LED of the mouse stays off and there's no connection.
I've never seen the mouse with no BT-LED before, because when the mouse is on BT is also on.
It seems that MN says the mouse to switch off BT ???
With Navio (for example) the connection is working on COM4.
It also worked with WM2003.
Has anybody any ideas?
Greetings
ossi
I use the GNS 5840 BT/TMC receiver.
It seems that the WM 5.0 BT stack does not allow for serial connection at 38400 baud which is needed by GNS/Navigon receivers.
I cannot connect at all to my receiver.
Error message from CruxView: "Could not set baudrate"
Sascha
My mouse is running with 4800 Baud and with Navio it works, only with MN4.2 i have this problem.
Ossi
The original Navigon GPS receiver (Navigon modular) which was shipped with MN|4.x is manufactured by GNS and runs on 38400 baud.
Sascha
It's an updated MN4.2 (i think 1.5 was the version with my receiver) and it worked with WM2003.
ossi
i am having a problem connecting to both recievers (royaltek rgt-1000 and Leadtek Wireless GPS Reciever)
I am trying to get them to work with my Wizard (t-mobile Vario)
but i am not getting anywhere.......HELP.......... i can put the in and outgoing ports on the bluetooth thingy as com6 and com7 but in the tom tom i can not even see those.................HELP!!!!!!!!
Sounds like you are running TT5 without the 5.21 update, this sorts that problem
I have an i-Blue 737 BT GPS. I have it set up for COM2 and I can not get it to work correctly. I have tried it with GPS Tuner, GPS Gate, OziExplorer, iGuidance and Google Maps and it will not work with any of them. The only program it works with is Tom Tom 6. I had each program set to look at COM2. Any ideas?
What are you running? (Hint: if it's not WM6, you're posting in the wrong forum)
Have you got it set as an incomming or outgoing port?
Same hardware working fine
I have an iMate JasJam with exactly the same GPS which I purchased today.
In conjunction with WM6 Black & Tomtom 6 it is working fine.
It is appearing on COM0:
tomtom is well known for hogging gps all for itself and not letting anything else play.
Head to the forums at pocketgpsworld.com
to use my Pharos GPS I had to open an outgoing port on the 8525 bluetooth section I think com9 before it would talk to the gps.
TheGenix said:
I have an i-Blue 737 BT GPS. I have it set up for COM2 and I can not get it to work correctly. I have tried it with GPS Tuner, GPS Gate, OziExplorer, iGuidance and Google Maps and it will not work with any of them. The only program it works with is Tom Tom 6. I had each program set to look at COM2. Any ideas?
Click to expand...
Click to collapse
I'm on WM6. I have it set as an outgoing port.
TheGenix said:
I'm on WM6. I have it set as an outgoing port.
Click to expand...
Click to collapse
i think you have to set it on com 0 i have the exact same reicever and it work perfect on WM6 pro black 3.01 .